Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
Wiring Diagram VW TOURAN 2007 - Multimedia control unit - radio
| A | Battery |
| B | Starter |
| C | Alternator |
| J519 | Onboard supply control unit |
| J650 | Multimedia control unit, under front passenger seat |
| R | Radio |
| SA5 | Fuse 5 on fuse holder A |
| SC22 | Fuse 22 on fuse holder C |
| T12d | 12-pin connector |
| T26e | 26-pin connector |
| 508 | Screw connection (30), on electronics box |
Wiring Diagram VW TOURAN 2007 - Multimedia control unit - multimedia system operating unit
| E380 | Multimedia system operating unit |
| J519 | Onboard supply control unit |
| J650 | Multimedia control unit, under front passenger seat |
| T16l | 16-pin connector |
| T26e | 26-pin connector |
| 45 | Earth point, centre behind dash panel |
Wiring Diagram VW TOURAN 2007 - Multimedia control unit - multimedia system operating unit - multimedia display unit
| E380 | Multimedia system operating unit |
| J519 | Onboard supply control unit |
| J650 | Multimedia control unit, under front passenger seat |
| T8ac | 8-pin connector, on front of roof |
| T8ad | 8-pin connector |
| T16l | 16-pin connector |
| T26e | 26-pin connector |
| T26f | 26-pin connector |
| Y22 | Multimedia display unit 1 |
Wiring Diagram VW TOURAN 2007 - Multimedia control unit - DVD player
| J519 | Onboard supply control unit |
| J650 | Multimedia control unit, under front passenger seat |
| R7 | DVD player |
| T10ad | 10-pin connector |
| T26f | 26-pin connector |
VW TOURAN 2007 Overview of control units
| 1 - | ABS control unit -J104- |
| q | 26-pin connector assignment |
| q | 47-pin connector assignment |
| 2 - | Engine control unit -J623- |
| q | 121-pin connector assignment |
| q | 154-pin connector assignment |
| 3 - | Aerial selection control unit -J515- |
| 4 - | Vehicle inclination sender -G384- |
| 5 - | Convenience system central control unit -J393- |
| q | Connector assignment |
| 6 - | Traffic information control unit -J559- /Chip card reader control unit -J676- |
| q | Fitting location |
| 7 - | Climatronic control unit -J255- |
| 7 - | Air conditioning system control unit -J301- |
| 8 - | Control unit in dash panel insert -J285- |
| q | Connector assignment 32-pin connector -T32- |
| 8 - | Traffic data aerial -R173- |
| 9 - | Steering column electronics control unit -J527- |
| q | Fitting location from May 2010 |
| q | Connector assignment to May 2010 |
| q | Connector assignment from May 2010 |
| q | Connector assignment |
| 11 - | Park assist steering control unit -J791- / Parking aid control unit -J446- |
| q | Fitting location |
| q | Connector assignment |
| 12 - | Onboard supply control unit -J519- |
| q | Connector assignment to May 2010 |
| q | Fitting location from May 2010 |
| q | Connector assignment from May 2010 52-pin connector -T52 A--black- |
| q | Connector assignment from May 2010 52-pin connector -T52 B--white- |
| q | Connector assignment from May 2010 52-pin connector -T52 C--brown- |
| q | Connector assignment |
| 13 - | Mechatronic unit for dual clutch gearbox -J743- |
| q | 20-pin connector assignment |
| Dual clutch gearbox 0AM: |
| q | Fitting location |
| q | 25-pin connector assignment |
| 14 - | Voltage stabiliser -J532- |
| 15 - | Headlight range control unit -J431- |
| q | Connector assignment |
| 15 - | Control unit for cornering light and headlight range control -J745- |
| q | Connector assignment |
| q | Connector assignment 75-pin connector -T75- |
| q | Connector assignment 50-pin connector -T50- |
| 17 - | Power steering control unit -J500- |
| q | Connector assignment |
| q | Fitting location from May 2010 |
|
| 26-pin connector assignment: |
| A - | ABS control unit -J104- |
| Connector: |
| B - | 26-pin connector -T26a- on wiring harness |
| Back to overview |
| 47-pin connector assignment: |
| A - | ABS control unit -J104- |
| Connector: |
| B - | 47-pin connector -T47- /-T47a- on wiring harness |
| Back to overview |
|
| 121-pin connector assignment: |
| A - | Engine control unit -J623- |
| Connector: |
| B - | 81-pin connector -T81- on wiring harness |
| C - | 40-pin connector -T40- on wiring harness |
Note
| -T121- is comprised of items B and C. |
| Back to overview |
| 154-pin connector: |
| A - | Engine control unit -J623- |
| Connector: |
| B - | 94-pin connector -T94- on wiring harness |
| C - | 60-pin connector -T60- on wiring harness |
Note
| -T154- is comprised of items B and C. |
| Back to overview |
|
|
| Connector assignment: |
| A - | Convenience system central control unit -J393- |
| Connector: |
| B - | 6-pin connector -T6- on wiring harness |
| C - | 18-pin connector -T18- on wiring harness |
| D - | 8-pin connector -T8- on wiring harness |
| E - | 6-pin connector -T6- on wiring harness |
| F - | 18-pin connector -T18a- on wiring harness |
| Back to overview |
|
|
|
| 36-pin connector -T36- on wiring harness: |
| 1 - | Voltage supply positive, terminal 15 |
| 2 - | Voltage supply positive, terminal 30 |
| 3 - | Vacant |
| 4 - | Vacant |
| 5 - | Brake fluid level warning lamp -K33- |
| 6 - | Handbrake warning switch -F9- |
| 7 - | Immobiliser reader coil -D2- |
| 8 - | Immobiliser reader coil -D2- |
| 9 - | Speedometer -G21- Output signal on instrument cluster, not assigned in current flow diagram |
| 10 - | Vacant |
| 11 - | Vacant |
| 12 - | Data bus diagnostic interface -J533- Dash panel CAN, low |
| 13 - | Data bus diagnostic interface -J533- Dash panel CAN, high |
| 14 - | Vacant |
| 15 - | Data bus diagnostic interface -J533- Dash panel CAN wake-up wire |
| 16 - | Vacant |
| 17 - | Fuel gauge -G1- (full) |
| 18 - | Fuel gauge -G1- (empty) |
| 19 - | Earth connection 2, in main wiring harness -367- Terminal 31 |
| 20 - | Vacant |
| 21 - | Vacant |
| 22 - | Front left brake pad wear sender -G34- |
| 23 - | Vacant |
| 24 - | Fuel tank flap lock warning lamp |
| 25 - | Oil pressure switch -F1- |
| 26 - | Oil level and oil temperature sender -G266- |
| 27 - | Vacant |
| 28 - | Sliding sunroof adjustment control unit -J245- ,Control unit with display for radio and navigation -J503- Speedometer signal, output |
| 29 - | Vacant |
| 30 - | Vacant |
| 31 - | Vacant |
| 32 - | Vacant |
| 33 - | Earth connection (sender earth) in interior wiring harness -401- |
| 34 - | Windscreen washer fluid level sender -G33- |
| 35 - | Coolant shortage indicator sender -G32- |
| 36 - | Ambient temperature sensor -G17- |
| Back to overview |
| 32-pin connector -T32- on wiring harness: |
| 1 - | Fuel gauge sender -G- (full) |
| 2 - | Fuel gauge sender -G- (empty) |
| 3 - | Vacant |
| 4 - | Vacant |
| 5 - | Vacant |
| 6 - | Vacant |
| 7 - | Immobiliser reader coil -D2- |
| 8 - | Immobilizer reader coil 2 -D3- |
| 9 - | Vacant |
| 10 - | Vacant |
| 11 - | Oil level and oil temperature sender -G266- |
| 12 - | Vacant |
| 13 - | Vacant |
| 14 - | Vacant |
| 15 - | Front left brake pad wear sender -G34- |
| 16 - | Earth connection 22, in main wiring harness -367- |
| 17 - | Washer fluid level warning lamp -K37- |
| 18 - | Coolant temperature and coolant shortage warning lamp -K28- |
| 19 - | Ambient temperature sensor -G17- |
| 20 - | Earth connection 1 (sender earth) in main wiring harness -410- |
| 21 - | Vacant |
| 22 - | Vacant |
| 23 - | Vacant |
| 24 - | Vacant |
| 25 - | Handbrake warning lamp -K139- |
| 26 - | Brake fluid level warning lamp -K33- |
| 27 - | Oil pressure warning lamp -K3- |
| 28 - | Data bus diagnostic interface -J533- Dash panel CAN, high |
| 29 - | Data bus diagnostic interface -J533- Dash panel CAN, low |
| 30 - | Vacant |
| 31 - | Voltage supply positive, terminal 15 |
| 32 - | Voltage supply positive, terminal 30a |
| Back to overview |
|
|
| Connector assignment: |
| A - | Steering column electronics control unit -J527- |
| B - | Airbag connector: |
| 1 - | Airbag 1 - |
| 2 - | Airbag 1+ |
| 3 - | Airbag 2+ |
| 4 - | Airbag 2 - |
| C - | Connector for turn signal switch -E2- / Headlight dipper and flasher switch -E4- / Cruise control system switch -E45- : |
| 1 - | Cruise control system terminal 15 voltage supply |
| 2 - | CCS off |
| 3 - | Cruise control system (CCS) SET button -E227- Res (+), Set (-) |
| 4 - | CCS on/off |
| 5 - | Earth CCS |
| 6 - | Cruise control system terminal 58 illumination |
| 7 - | Headlight flasher |
| 8 - | Main beam |
| 9 - | Turn signal |
| 10 - | Turn signal earth |
| D - | 20-pin connector -T20d- on wiring harness |
| 1 - | Taxi two-way radio 2 |
| 2 - | Taxi two-way radio 1 |
| 3 - | Taxi alarm 2 |
| 4 - | Taxi alarm 1 |
| 5 - | Vacant |
| 6 - | Vacant |
| 7 - | Vacant |
| 8 - | Vacant |
| 9 - | Vacant |
| 10 - | Powertrain CAN shielding |
| 11 - | Data bus diagnostic interface -J533- / Connection 1 (powertrain CAN bus, low), in main wiring harness -B390- |
| 12 - | Data bus diagnostic interface -J533- / Connection 1 (powertrain CAN bus, high), in main wiring harness -B383- |
| 13 - | Cruise control system, output |
| 14 - | Data bus diagnostic interface -J533- / Connection 1 (convenience CAN bus, high), in main wiring harness -B397- |
| 15 - | Data bus diagnostic interface -J533- / Connection 1 (convenience CAN bus, low), in main wiring harness -B406- |
| 16 - | Selector lever locked in position P switch -F319- |
| 17 - | Terminal 15 |
| 18 - | Terminal 50 |
| 19 - | Terminal 30 |
| 20 - | Terminal 31 |
| E - | 4-pin connector -T4ak- on wiring harness |
| 1 - | Airbag 1 - |
| 2 - | Airbag 1+ |
| 3 - | Airbag 2+ |
| 4 - | Airbag 2 - |
| F - | 12-pin connector -T12j- / ignition/starter switch -D- / ignition key withdrawal lock solenoid -N376- : |
| 1 - | Vacant |
| 2 - | Vacant |
| 3 - | 2-pin connector -T2dy- / ignition key withdrawal lock solenoid -N376- Terminal 30 |
| 4 - | 2-pin connector -T2dy- / ignition key withdrawal lock solenoid -N376- Earth |
| 5 - | Vacant |
| 6 - | Vacant |
| 7 - | Ignition/starter switch -D- Terminal 50, output |
| 8 - | Ignition/starter switch -D- Terminal 30 |
| 9 - | Ignition/starter switch -D- Terminal S, output |
| 10 - | Ignition/starter switch -D- Terminal X, output |
| 11 - | Ignition/starter switch -D- Terminal P, output |
| 12 - | Ignition/starter switch -D- Terminal 15, output |
| G - | Connector for intermittent wiper switch -E22- / sliding sunroof adjustment regulator -E38- / washer pump switch (automatic wash/wipe and headlight washer system) -E44- / multifunction display call-up button -E86- / reset button -E92- : |
| 1 - | Wiper switch signal |
| 2 - | Earth wiper |
| 3 - | Rear lid wash/wipe signal |
| 4 - | Vacant |
| 5 - | MFD signal |
| 6 - | Earth MFD, interval potentiometer |
| 7 - | Intermittent operation speeds signal |
| 8 - | Vacant |
| H - | Connector for steering angle sender -G85- : |
| 1 - | Photoelectric beam 5 |
| 2 - | Photoelectric beam 3 |
| 3 - | Photoelectric beam 1 |
| 4 - | 12 Volt voltage supply, steering angle sender |
| 5 - | 5 Volt voltage supply, steering angle sender |
| 6 - | Photoelectric beam 6 |
| 7 - | Photoelectric beam 4 |
| 8 - | Photoelectric beam 2 |
| 9 - | Earth |
| 10 - | Photoelectric beam 7 |
| I - | 10-pin connector -T10x- / coil connector -F350- / airbag coil connector and return ring with slip ring -F138- : |
| 1 - | Vacant |
| 2 - | Vacant |
| 3 - | Airbag 1 + |
| 4 - | Airbag 1 - |
| 5 - | Airbag 2 + |
| 6 - | Airbag 2 - |
| 7 - | Earth for coil connector, multifunction steering wheel and signal horn |
| 8 - | CCS in detent -Off-, signal horn |
| 9 - | LIN bus, heated steering wheel temperature sensor |
| 10 - | Multifunction steering wheel voltage supply terminal 15 |
| Back to overview |
| Steering column electronics control unit -J527- , from May 2010 |
| Fitting location: |
| 1 - | Steering column electronics control unit -J527- |
| Near steering column switch |
| Connectors: |
| q | -A-16-pin connector -T16k- |
| q | -B-4-pin connector -T4k- |
| Back to overview |
|
| 1 - | Fuse 6 on fuse holder B -SB6- via B504 Positive connection 8 (30a) in interior wiring harness |
| q | Only models with no start/stop system |
| - Fuse 57 on fuse holder C -SC57- via B321 Positive connection 7 (30a) in main wiring harness |
| q | Only models with start/stop system |
| 2 - | 382 Earth connection 17 in main wiring harness |
| 3 - | B406 Connection 1 (convenience CAN bus, low), in main wiring harness |
| 4 - | B397 Connection 1 (convenience CAN bus, high), in main wiring harness |
| 5 - | Engine control unit -J623- , GRA E_A) |
| 6 - | Onboard supply control unit -J519- , (T52c/14), (terminal 50) |
| 7 - | Terminal S, vacant |
| 8 - | Vacant |
| 9 - | Vacant |
| 10 - | Vacant |
| 11 - | Selector lever locked in position P switch -F319- , P locked |
| 12 - | B390 Connection 1 (powertrain CAN bus, low), in main wiring harness |
| 13 - | B383 Connection 1 (powertrain CAN bus, high), in main wiring harness |
| 14 - | Onboard supply control unit -J519- , (T52c/13, T52c/31) |
| 15 - | Vacant |
| 16 - | Vacant |
|
| 1 - | Airbag control unit -J234- , (T50/21), (airbag 1+) |
| 2 - | Airbag control unit -J234- , (T50/20), (airbag 1–) |
| 3 - | Vacant |
| 4 - | Vacant |
| Back to overview |
|
|
| Connector assignment: |
| A - | Data bus diagnostic interface -J533- |
| Connector: |
| B - | 20-pin connector -T20- on wiring harness |
| Back to overview |
|
| A - | Park assist steering control unit -J791- / Parking aid control unit -J446- |
| B - | Front parking aid warning buzzer -H22- |
| Back to overview |
| Connector assignment: |
| A - | Parking aid control unit -J446- / park assist steering control unit -J791- |
| B - | 16-pin connector -T16j- |
| Connector assignment: |
| 1 - | Fuse 11 on fuse holder B -SB11- Terminal 15 |
| 2 - | Rear parking aid warning buzzer -H15- Pin 1 - |
| 3 - | Vacant |
| 4 - | Parking aid button -E266- Pin 4 |
| 5 - | Vacant |
| 6 - | Data bus diagnostic interface -J533- , Powertrain CAN bus high |
| 7 - | Vacant |
| 8 - | Earth connection |
| 9 - | Warning light for park assist steering -K241- Pin 2 |
| 10 - | Rear parking aid warning buzzer -H15- Pin 1 + |
| 11 - | Vacant |
| 12 - | Vacant |
| 13 - | Parking aid warning lamp -K136- Pin 2 |
| 14 - | Vacant |
| 15 - | Data bus diagnostic interface -J533- Powertrain CAN bus low |
| 16 - | Park assist steering button -E581- Pin 5 |
| C - | 12-pin connector -T12t- |
| Connector assignment: |
| 1 - | Front sender, pin 3 - |
| 2 - | Front sender, pin 1 + |
| 3 - | Front parking aid warning buzzer -H22- Pin 2 - |
| 4 - | Front parking aid warning buzzer -H22- Pin 1 + |
| 5 - | Front left parking aid sender -G255- Pin 2 signal |
| 6 - | Front centre left parking aid sender -G254- Pin 2 signal |
| 7 - | Front centre right parking aid sender -G253- Pin 2 signal |
| 8 - | Front right parking aid sender -G252- Pin 2 signal |
| 9 - | Front left sender for park assist steering on left side of vehicle -G568- Pin 2 signal |
| 10 - | Front right sender for park assist steering on right side of vehicle -G569- Pin 2 signal |
| 11 - | Vacant |
| 12 - | Vacant |
| D - | 12-pin connector -T12n- |
| Connector assignment: |
| 1 - | Vacant |
| 2 - | Rear centre right parking aid sender -G205- Pin 2 signal |
| 3 - | Rear centre left parking aid sender -G204- Pin 2 signal |
| 4 - | Rear right parking aid sender -G206- Pin 2 signal |
| 5 - | Rear left parking aid sender -G203- Pin 2 signal |
| 6 - | Vacant |
| 7 - | Vacant |
| 8 - | Rear sender Pin 3 - |
| 9 - | Vacant |
| 10 - | Vacant |
| 11 - | Rear sender, pin 1 + |
| 12 - | Vacant |
| Back to overview |
|
| Connector assignment: |
| A = 11-pin connector -T11b- on wiring harness |
| 1 - | Terminal 30 |
| 2 - | Right dipped beam bulb/ right gas discharge light control unit |
| 3 - | Right main beam bulb (not for xenon) |
| 4 - | Right fog light bulb |
| 5 - | Right dipped beam screen motor (xenon) |
| 6 - | Front right turn signal bulb |
| 7 - | Left side light bulb |
| 8 - | Vacant |
| 9 - | Earth |
| 10 - | Fuel pump control unit |
| 11 - | Terminal 50 voltage supply relay |
| B = 12-pin connector -T12a- on wiring harness: |
| 1 - | Right reversing light bulb, automatic anti-dazzle interior mirror |
| 2 - | Vacant |
| 3 - | Vacant |
| 4 - | Rear left fog light bulb |
| 5 - | Right brake light bulb |
| 6 - | Vacant |
| 7 - | Footwell lighting bulb front left, footwell lighting bulb front right |
| 8 - | Vacant |
| 9 - | Right tail light bulb |
| 10 - | Rear right turn signal bulb |
| 11 - | Left interior light, right interior light, button illumination bulb |
| 12 - | Terminal 58d |
| Back to overview |
| C = 12-pin connector -T12m- on wiring harness: |
| 1 - | Heated driver seat control unit, heated front passenger seat control unit |
| 2 - | Left brake light bulb |
| 3 - | Vacant |
| 4 - | Vacant |
| 5 - | Vacant |
| 6 - | Vacant |
| 7 - | Vacant |
| 8 - | Number plate light |
| 9 - | Additional brake light bulb |
| 10 - | Left tail light bulb |
| 11 - | Rear left turn signal bulb |
| 12 - | Left reversing light bulb (only models without rear left fog light bulb) |
| D = 11-pin connector -T11c- on wiring harness: |
| 1 - | Terminal 30 |
| 2 - | Left fog light bulb |
| 3 - | Left headlight main beam bulb |
| 4 - | Left headlight dipped beam bulb |
| 5 - | Earth |
| 6 - | Left dipped beam screen motor |
| 7 - | Bridge to T8a/2- |
| 8 - | Headlight washer system relay |
| 9 - | Vacant |
| 10 - | Right side light bulb |
| 11 - | Front left turn signal bulb |
| E = 16-pin connector -T16k- on wiring harness: |
| 1 - | Lighting switch terminal 58 |
| 2 - | Brake light switch |
| 3 - | Vacant |
| 4 - | Vacant |
| 5 - | Vacant |
| 6 - | Fog light switch |
| 7 - | Earth (only models with manual gearbox not for American markets) |
| 7 - | Clutch position sender (only models with manual gearbox for American markets) |
| 8 - | Lighting switch terminal 56 |
| 9 - | Vacant |
| 10 - | Vacant |
| 11 - | Vacant |
| 12 - | Vacant |
| 13 - | Rear fog light switch |
| 14 - | Light switch, driving light assist |
| 15 - | Vacant |
| 16 - | Light switch (daytime running lights) |
| Back to overview |
| F = 8-pin connector -T8a- on wiring harness: |
| 1 - | Terminal 50 voltage supply relay |
| 2 - | Bridge to Connector -T11c/7- |
| 3 - | Windscreen wiper motor, rain and light sensor (LIN bus) |
| 4 - | Alternator -C- |
| 5 - | Bonnet contact switch |
| 6 - | Vacant |
| 7 - | Terminal 30 |
| 8 - | Terminal 31 |
| G = 12-pin connector -T12n- on wiring harness: |
| 1 - | Steering column electronics control unit terminal 50 |
| 2 - | Indicator lamp for hazard warning light |
| 3 - | Vacant |
| 4 - | Switch and instrument illumination regulator |
| 5 - | Vacant |
| 6 - | Vacant |
| 7 - | Convenience CAN bus low |
| 8 - | Convenience CAN bus high |
| 9 - | Hazard warning light switch |
| 10 - | Switch and instrument illumination regulator |
| 11 - | Steering column electronics control unit terminal 15 |
| 12 - | Switch and instrument illumination regulator |
| H = 12-pin connector : |
| - | Pin connector H is vacant. |
| Back to overview |
| I = 2-pin connector -T2z- on wiring harness: |
| 1 - | Fuses terminal 30 |
| 2 - | Terminal 75a |
| J = 6-pin connector -T6l- on wiring harness: |
| 1 - | Washer pump fuse |
| 2 - | Washer pump |
| 3 - | Horn fuse |
| 4 - | Washer pump |
| 5 - | Earth |
| 6 - | Treble tone horn, bass tone horn |
| K = 10-pin connector -T10- on wiring harness: |
| 1 - | Heated rear window |
| 2 - | Vacant |
| 3 - | Vacant |
| 4 - | Vacant |
| 5 - | Fuse terminal 30 |
| 6 - | Heated rear window fuse |
| 7 - | Vacant |
| 8 - | Vacant |
| 9 - | Vacant |
| 10 - | Terminal 30g |
| L = 2-pin connector -T2- - on wiring harness: |
| 1 - | Fuse terminal 30 |
| 2 - | Interior terminal 15 |
| Back to overview |
|
