Wiring Diagram VW PASSAT CC 2016 - Control unit for electromechanical parking brake - parking brake motor left and right - lateral acceleration sender - yaw rate sender - longitudinal acceleration sender

| G200 | Lateral acceleration sender |
| G202 | Yaw rate sender |
| G251 | Longitudinal acceleration sender |
| G476 | Clutch position sender |
| J104 | ABS control unit |
| J540 | Control unit for electromechanical parking brake |
| SC2 | Fuse 2 on fuse holder C |
| SC22 | Fuse 22 on fuse holder C |
| SC24 | Fuse 24 on fuse holder C |
| T2an | 2-pin connector, black |
| T2ao | 2-pin connector, black |
| T5j | 5-pin connector |
| T30 | 30-pin connector |
| T38 | 38-pin connector |
| V282 | Left parking brake motor |
| V283 | Right parking brake motor |
| 688 | Earth point 2, on centre tunnel |
| B287 | Connection 11 (15a), in main wiring harness |
| B384 | Connection 2 (powertrain CAN bus, high), in main wiring harness |
| B391 | Connection 2 (powertrain CAN bus, low), in main wiring harness |
| * | Only models with manual gearbox |
| ** | Only models with automatic gearbox |
| *** | Only models with auto-hold function |
Wiring Diagram VW PASSAT CC 2016 - Control unit for electromechanical parking brake - button for electromechanical parking brake
| E538 | Button for electromechanical parking brake, left of dash panel |
| E540 | AUTO HOLD button, near gear selector |
| J285 | Control unit in dash panel insert |
| J540 | Control unit for electromechanical parking brake |
| K213 | Electromechanical parking brake warning lamp |
| K237 | Auto-hold warning lamp |
| L76 | Button illumination bulb |
| SC17 | Fuse 17 on fuse holder C |
| T6h | 6-pin connector |
| T10i | 10-pin connector |
| T30 | 30-pin connector |
| T32c | 32-pin connector |
| 249 | Earth connection 2, in interior wiring harness |
| 396 | Earth connection 31, in main wiring harness |
| 639 | Earth point, left A-pillar |
| 687 | Earth point 1, on centre tunnel |
| B332 | Connection 18 (30a), in main wiring harness |
| B340 | Connection 1 (58d), in main wiring harness |
| B482 | Connection 18, in main wiring harness |
| *** | Only models with auto-hold function |
Wiring Diagram VW PASSAT CC 2016 - Dash panel insert - multifunction display - data bus diagnosis interface
VW PASSAT CC 2016 Overview of control units
Overview of control units |
| 1 - | Auxiliary heater control unit -J364- |
| 2 - | Power steering control unit -J500- |
| 3 - | ABS control unit -J104- |
| 4 - | Automatic gearbox control unit -J217- |
| 4 - | Voltage stabiliser -J532- |
| 4 - | Mechatronic unit for dual clutch gearbox -J743- |
| 5 - | Engine control unit -J623- |
| 6 - | Adaptive cruise control unit -J428- |
| Auxiliary heater control unit -J364- | | behind the right front wheel housing liner | | - | Auxiliary heater control unit -J364- | | - | 2-pin connector -T2- -T2cn- | | - | 8-pin connector -T8- -T8ai- | | |
|
VW PASSAT CC 2016 Power steering control unit J500Power steering control unit -J500- | | At the steering on the subframe | | A - | 5-pin connector -T5- -T5z- | | B - | 2-pin connector -T2- -T2fn | | |
|
| On bulkhead, on right in engine compartment -arrow- | | - | 38-pin connector -T38- -T38- | | |
|
| Automatic gearbox control unit -J217- | | In front left wheel housing -arrow- | | - | 52-pin connector -T52- -T52- | | |
|
| Voltage stabiliser -J532- | | In front left wheel housing -arrow- | | - | 12-pin connector -T12- -T12ad- | | |
|
| Engine control unit -J623- | | under centre of plenum chamber cover -arrow- | | A - | 94-pin connector -T94- -T94- | | B - | 60-pin connector -T60- -T60- | | |
|
| Adaptive cruise control unit -J428- | | behind radiator in centre -arrow- | | - | 10-pin connector -T10- -T10y- | | |
|
| Mechatronic unit for dual clutch gearbox -J743- |
| 1 - | Mechatronic unit for dual clutch gearbox -J743- |
| A - | 20-pin connector -T20m- |
| Note: | The illustration does not correspond with the selected vehicle, but the fitting location is the same. | | | |