Čeština
Dansk
Deutsch
Ελληνικά
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
Wiring Diagram VW PARATI 2008 - Battery - starter - alternator - voltage regulator
| A | Battery |
| B | Starter |
| C | Alternator |
| C1 | Voltage regulator |
| T2o | 2-pin connector, near battery |
| T2p | 2-pin connector, on alternator |
| T6i | 6-pin connector, behind the left trim in front dash panel |
| 1 | Earth strap, battery - body |
| 49 | Earth point, near battery |
| 500 | Screw connection 1 (30), on relay plate |
| 501 | Screw connection 2 (30), on relay plate |
| D26 | Positive connection (B+), in alternator wiring harness |
| P1 | Positive connection (30), in fuse holder on battery |
Wiring Diagram VW PARATI 2008 - Ignition/starter switch - speedometer sender - X-contact relief relay
| D | Ignition/starter switch |
| G22 | Speedometer sender |
| J59 | X-contact relief relay |
| J362 | Immobilizer control unit |
| R | Radio |
| T3c | 3-pin connector, on speedometer sender |
| T6a | 6-pin connector, behind the right trim in front dash panel |
| T7c | 7-pin connector, on ignition/starter switch |
| T8a | 8-pin connector, on immobilizer control unit |
| T8d | 8-pin connector, on radio |
| 331 | Earth connection, in injection system wiring harness |
| A2 | Positive connection (15), in dash panel wiring harness |
| E40 | Connection (speedometer sender), in injection system wiring harness |
| E41 | Positive connection (15), in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Hall sender - engine control unit - ignition transformer - ignition transformer output stage - ignition distributor - spark plug connector - spark plugs
| G40 | Hall sender |
| J623 | Engine control unit |
| N152 | Ignition transformer |
| N157 | Ignition transformer output stage |
| O | Ignition distributor |
| P | Spark plug connector |
| Q | Spark plugs |
| T2a | 2-pin connector, on ignition transformer output stage |
| T3b | 3-pin connector, on Hall sender |
| T45a | 45-pin connector, on engine control unit |
| 43 | Earth point, lower part of right A-pillar |
| 340 | Earth connection 2, in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Intake air temperature sender - coolant temperature sender - throttle valve potentiometer - intake manifold pressure sender - engine control unit
| G42 | Intake air temperature sender |
| G62 | Coolant temperature sender |
| G69 | Throttle valve potentiometer |
| G71 | Intake manifold pressure sender |
| J623 | Engine control unit |
| N80 | Activated charcoal filter system solenoid valve 1 |
| T2b | 2-pin connector, on active charcoal filter system solenoid valve 1 |
| T2d | 2-pin connector, on coolant temperature sender |
| T3a | 3-pin connector, on throttle valve potentiometer |
| T4x | 4-pin connector, on intake air temperature sender |
| T5o | 5-pin connector, near cylinder head cover |
| T6a | 6-pin connector, behind the right trim in front dash panel |
| T45a | 45-pin connector, on engine control unit |
| 339 | Earth connection (sender earth), in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Engine control unit - injector - cylinder 1 - injector - cylinder 2 - injector - cylinder 3 - injector - cylinder 4 - throttle valve module
| J623 | Engine control unit |
| N30 | Injector, cylinder 1 |
| N31 | Injector, cylinder 2 |
| N32 | Injector, cylinder 3 |
| N33 | Injector, cylinder 4 |
| T1a | Single pin connector, behind the right trim in front dash panel |
| T2ca | 2-pin connector, on injector, cylinder 1 |
| T2cb | 2-pin connector, on injector, cylinder 2 |
| T2cc | 2-pin connector, on injector, cylinder 3 |
| T2cd | 2-pin connector, on injector, cylinder 4 |
| T4b | 4-pin connector, on throttle valve positioner |
| T5p | 5-pin connector, near cylinder head cover |
| T45a | 45-pin connector, on engine control unit |
| V60 | Throttle valve positioner |
| E45 | Connection (87), in injection system wiring harness |
| E48 | Connection (injectors), in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Lambda probe - knock sensor 1 - engine control unit - push-in bridge
| G39 | Lambda probe |
| G61 | Knock sensor 1 |
| J362 | Immobilizer control unit |
| J623 | Engine control unit |
| T2c | 2-pin connector, on push-in bridge |
| T2e | 2-pin connector, on knock sensor 1 |
| T4c | 4-pin connector, on Lambda probe |
| T6a | 6-pin connector, behind the right trim in front dash panel |
| T8a | 8-pin connector, on immobilizer control unit |
| T45a | 45-pin connector, on engine control unit |
| TV23 | Push-in bridge |
Wiring Diagram VW PARATI 2008 - Engine control unit
| F163 | Thermal switch for air conditioning system shut-off |
| J623 | Engine control unit |
| T1au | Single pin connector, on thermal switch for air conditioning system shut-off |
| T6c | 6-pin connector, behind the right trim in front dash panel |
| T8b | 8-pin connector, behind dash panel |
| T45a | 45-pin connector, on engine control unit |
| E96 | Connection 5, in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Fuel gauge sender - coolant temperature sender - fuel system pressurisation pump
| G | Fuel gauge sender |
| G2 | Coolant temperature sender |
| G6 | Fuel system pressurisation pump |
| S13 | Fuse in relay plate fuse holder |
| T2ag | 2-pin connector, on coolant temperature sender |
| T4i | 4-pin connector, on fuel pump |
| T6a | 6-pin connector, behind the right trim in front dash panel |
| T6b | 6-pin connector, behind the right trim in front dash panel |
| T6e | 6-pin connector, behind the dash panel near relay plate |
| T16a | 16-pin connector, behind driver storage compartment |
| 86 | Earth connection 1, in rear wiring harness |
| 335 | Earth connection 5, in dash panel wiring harness |
| 625 | Earth point, left tail light |
| A164 | Positive connection 2 (30a), in dash panel wiring harness |
| E42 | Positive connection (30a), in injection system wiring harness |
Wiring Diagram VW PARATI 2008 - Fuel pump relay - air conditioning system switch-off relay
| F129 | Air conditioning system pressure switch |
| J17 | Fuel pump relay |
| J365 | Air conditioning system switch-off relay |
| N25 | Air conditioning system magnetic coupling |
| S14 | Fuse in relay plate fuse holder |
| T1i | Single pin connector, on air conditioning system magnetic clutch |
| T4e | 4-pin connector, on air conditioning system pressure switch |
| T6a | 6-pin connector, behind the right trim in front dash panel |
| T6c | 6-pin connector, behind the right trim in front dash panel |
| T6j | 6-pin connector, behind the left trim in front dash panel |
| T9a | 9-pin connector, on air conditioning system switch-off relay |
| T9b | 9-pin connector, on fuel pump relay |
Wiring Diagram VW PARATI 2008 - Fuel gauge - coolant temperature gauge - rev. counter - control unit with display in dash panel insert - dash panel insert - alternator warning lamp
| G1 | Fuel gauge |
| G3 | Coolant temperature gauge |
| G5 | Rev. counter |
| J285 | Control unit with display in dash panel insert |
| K | Dash panel insert |
| K2 | Alternator warning lamp |
| K101 | Speed warning lamp, yellow symbol |
| K105 | Reserve fuel warning lamp |
| T6g | 6-pin connector, behind the dash panel near relay plate |
| T32a | 32-pin connector, on dash panel insert |
VW PARATI 2008 ABS control unit J104
| ABS control unit -J104- |
|
| Designation of connector: |
| A - | ABS control unit -J104- |
| B - | 31-pin connector, on ABS control unit -T31a- |
|
|
| Designation of connector: |
| A - | Airbag control unit -J234- |
| B - | 75-pin connector, on ABS control unit -T75a- |
|
|
| Designation of connector: |
| A - | Control unit with display in dash panel insert -J285- |
| B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
| 1 - | Vacant |
| 2 - | Engine control unit |
| 3 - | Terminal 15a |
| 4 - | Terminal R |
| 5 - | Fuel gauge sender |
| 6 - | Airbag control unit |
| 7 - | Terminal 31 |
| 8 - | Coolant temperature sender |
| 9 - | Terminal 31 |
| 10 - | Oil pressure switch |
| 11 - | Engine control unit |
| 12 - | Terminal 61 |
| 13 - | Engine control unit |
| 14 - | Terminal 75 |
| 15 - | Terminal 58 |
| 16 - | Terminal 58 |
| 17 - | Radio |
| 18 - | Radio |
| 19 - | ABS control unit |
| 20 - | Immobilizer control unit |
| 21 - | Radio |
| 22 - | Terminal L |
| 23 - | Terminal 30 |
| 24 - | Terminal 31 |
| 25 - | Terminal K |
| 26 - | Speedometer sender |
| 27 - | Engine control unit |
| 28 - | Speedometer sender |
| 29 - | Brake system monitoring |
| 30 - | Terminal 56a |
| 31 - | Terminal 58d |
| 32 - | Terminal 58d |
| B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
Note
| for models with 1.0 l Flex engine, 1.0 l and 1.4 l petrol engines only, from March 2008 |
| 1 - | Terminal 30 |
| 2 - | Terminal 31 |
| 3 - | Turn signal |
| q | only for Gol Phoenix |
| 4 - | Terminal CAN-Bus high |
| 5 - | Terminal CAN-Bus low |
| 6 - | Vacant |
| 7 - | Radio |
| 8 - | Radio |
| 9 - | Radio |
| 10 - | Terminal 61 |
| 11 - | Terminal 56a |
| 12 - | ABS control unit |
| 13 - | Airbag control unit |
| 14 - | Brake system monitoring |
| 15 - | Immobilizer control unit |
| 16 - | Immobilizer control unit |
| 17 - | Terminal 15 |
| 18 - | Terminal 31 |
| 19 - | Vacant |
| 20 - | Terminal 31 |
| 21 - | CAN Shield |
| 22 - | Fuel gauge sender |
| 23 - | Oil pressure switch |
| 24 - | S-contact |
| 25 - | Speedometer sender |
| 26 - | Terminal K |
| 27 - | Terminal L |
| 28 - | Vacant |
| 29 - | Terminal 75 |
| 30 - | Terminal 58d |
| 31 - | Terminal 58d |
| 32 - | Terminal R |
Note
|
|
| Designation of connector: |
| A - | Control unit with display in dash panel insert -J285- |
| B - | 32-pin connector, on control unit in dash panel insert -T32a- |
| 1 - | Speedometer sender |
| 2 - | Vacant |
| 3 - | Terminal 15 |
| 4 - | Terminal R |
| 5 - | Fuel gauge sender |
| 6 - | Airbag control unit |
| 7 - | Terminal 31 |
| 8 - | Coolant temperature sender |
| 9 - | Terminal 31 |
| 10 - | Oil pressure switch |
| 11 - | Engine control unit |
| 12 - | Terminal 61 |
| 13 - | Engine control unit |
| 14 - | Terminal 75 |
| 15 - | Oil pressure switch |
| 16 - | Immobilizer control unit |
| 17 - | Radio |
| 18 - | Radio |
| 19 - | ABS control unit |
| 20 - | Terminal 58d |
| 21 - | Radio |
| 22 - | Coolant shortage indicator sender |
| 23 - | Terminal 30 |
| 24 - | Terminal 31 |
| 25 - | Terminal K |
| 26 - | Terminal 58 |
| 27 - | Engine control unit |
| 28 - | Speedometer sender |
| 29 - | Brake system monitoring |
| 30 - | Terminal 56a |
| 31 - | Terminal L |
| 32 - | Terminal 56 |
|
|
| Designation of connector: |
| A - | Convenience system central control unit -J393- |
| B - | 12-pin connector, on convenience system central control unit -T12c- |
| C - | 23-pin connector, on convenience system central control unit -T23a- |
| D - | 12-pin connector, on convenience system central control unit -T12b- |
|
|
| Designation of connector: |
| A - | Engine control unit -J623- |
| B/C - | 80-pin connector, on engine control unit -T80a- |
|
|
| Designation of connector: |
| A - | Air conditioning system control unit -J301- |
| B - | 5-pin connector, on air conditioning system control unit -T5d- |
| C - | 7-pin connector, on heater control unit -T7d- |
|
|
| Designation of connector: |
| A - | Immobilizer control unit -J362- |
| B - | 8-pin connector, on immobilizer control unit -T8g- |
| C - | 2-pin connector, on immobilizer control unit -T2bp- |
|
|
| Designation of connector: |
| A - | Alarm system control unit -J85- |
| B - | 22-pin connector, on alarm system control unit -T22a- |