Wiring Diagram VW JETTA NF 2017 - Battery - Alternator - Voltage regulator - Onboard supply control unit - Fuse 1 in fuse holder A - Fuse 2 in fuse holder A - Fuse 5 in fuse holder A
| A | Battery |
| C | Alternator |
| C1 | Voltage regulator |
| J519 | Onboard supply control unit |
| SA | Fuse holder A |
| SA1 | Fuse 1 in fuse holder A |
| SA2 | Fuse 2 in fuse holder A |
| SA5 | Fuse 5 in fuse holder A |
| T2ay | 2-pin connector |
| T4 | 4-pin connector |
| T73 | 73-pin connector |
| T73b | 73-pin connector |
| 12 | Earth point, on left in engine compartment |
| 652 | Earth point, engine and gearbox earth |
| 714 | Earth point on right of engine |
| * | Only models with "Low" equipment (AW0) |
| *2 | Only models with "High" equipment (AW1) |
| *3 | Wiring colour depends on equipment |
Wiring Diagram VW JETTA NF 2017 - Starter - Terminal 30 voltage supply relay - Onboard supply control unit - Terminal 50 voltage supply relay
| B | Starter |
| J317 | Terminal 30 voltage supply relay |
| J519 | Onboard supply control unit |
| J682 | Terminal 50 voltage supply relay |
| T73 | 73-pin connector |
| T73a | 73-pin connector |
| T73b | 73-pin connector |
| 44 | Earth point, lower part of left A-pillar |
| 366 | Earth connection 1, in main wiring harness |
| 367 | Earth connection 2, in main wiring harness |
| 605 | Earth point, on top end of steering column |
| B169 | Positive connection 1 (30), in interior wiring harness |
| B170 | Positive connection 2 (30), in interior wiring harness |
| B239 | Positive connection 1 (50), in interior wiring harness |
| B240 | Positive connection 2 (50), in interior wiring harness |
| * | Only models with automatic gearbox |
| *2 | Only models with "High" equipment (AW1) |
| *3 | Only models with "Low" equipment (AW0) |
| *4 | Cross section depends on equipment |
| *5 | Only models with manual gearbox |
Wiring Diagram VW JETTA NF 2017 - Ignition/starter switch - Cruise control system switch - Onboard supply control unit
| D | Ignition/starter switch |
| E45 | Cruise control system switch |
| J519 | Onboard supply control unit |
| T7 | 7-pin connector |
| T16x | 16-pin connector |
| T73b | 73-pin connector |
| A16 | Connection (CCS), in dash panel wiring harness |
| A33 | Connection (75), in dash panel wiring harness |
| B165 | Positive connection 2 (15), in interior wiring harness |
| B171 | Positive connection 3 (30), in interior wiring harness |
| B188 | Positive connection 5 (30), in interior wiring harness |
| * | Only models with "High" equipment (AW1) |
| *2 | Cross section depends on equipment |
Wiring Diagram VW JETTA NF 2017 - Onboard supply control unit
| J519 | Onboard supply control unit |
| T73 | 73-pin connector |
| T73a | 73-pin connector |
| T73b | 73-pin connector |
| * | Only models with "High" equipment (AW1) |
| *2 | Only models with "Low" equipment (AW0) |
Wiring Diagram VW JETTA NF 2017 - Fuse holder C - Fuse 30 on fuse holder C - Fuse 32 on fuse holder C - Fuse 33 on fuse holder C
| SC | Fuse holder C |
| SC28 | Fuse 28 on fuse holder C |
| SC30 | Fuse 30 on fuse holder C |
| SC31 | Fuse 31 on fuse holder C |
| SC32 | Fuse 32 on fuse holder C |
| SC33 | Fuse 33 on fuse holder C |
| SC41 | Fuse 41 on fuse holder C |
| T14a | 14-pin connector |
| B146 | Positive connection 1 (87), in interior wiring harness |
| * | Cross section depends on equipment |
| *2 | Only models with 1.4l engine |
| *3 | Only models with "Low" equipment (AW0) |
| *4 | Only models with "High" equipment (AW1) |
Wiring Diagram VW JETTA NF 2017 - Fuse holder C - Fuse 3 on fuse holder C - Fuse 20 on fuse holder C - Fuse 24 on fuse holder C - Diagnostic connection
| F138 | Airbag coil connector and return ring with slip ring |
| SC | Fuse holder C |
| SC3 | Fuse 3 on fuse holder C |
| SC20 | Fuse 20 on fuse holder C |
| SC24 | Fuse 24 on fuse holder C |
| SC25 | Fuse 25 on fuse holder C |
| T16 | 16-pin connector |
| T16y | 16-pin connector |
| U31 | Diagnostic connection |
| A167 | Positive connection 3 (30a) in dash panel wiring harness |
| B172 | Positive connection 4 (30), in interior wiring harness |
| B218 | Positive connection 6 (30), in interior wiring harness |
| B302 | Positive connection 6 (30), in main wiring harness |
| E114 | Connection (air conditioning system, 15a), in dash panel wiring harness |
| * | Cross section depends on equipment |
Wiring Diagram VW JETTA NF 2017 - Engine control unit - Fuse holder C - Fuse 4 on fuse holder C - Fuse 6 on fuse holder C
| J623 | Engine control unit |
| SC | Fuse holder C |
| SC4 | Fuse 4 on fuse holder C |
| SC6 | Fuse 6 on fuse holder C |
| T121 | 121-pin connector |
| B278 | Positive connection 2 (15a) in main wiring harness |
| * | Wiring colour depends on equipment |
| *2 | Cross section depends on equipment |
Wiring Diagram VW JETTA NF 2017 - Engine control unit - Diagnostic connection
| J623 | Engine control unit |
| T14a | 14-pin connector |
| T16 | 16-pin connector |
| T121 | 121-pin connector |
| U31 | Diagnostic connection |
| 85 | Earth connection 1, in engine compartment wiring harness |
| 368 | Earth connection 3, in main wiring harness |
| 389 | Earth connection 24, in main wiring harness |
| 641 | Earth point 3, left in engine compartment |
| A76 | Connection (K-diagnosis wire), in dash panel wiring harness |
| * | From July 2014 |
Wiring Diagram VW JETTA NF 2017 - Engine control unit - Ignition coil 1 with output stage - Ignition coil 2 with output stage - Ignition coil 3 with output stage - Ignition coil 4 with output stage - Spark plug connector
| J623 | Engine control unit |
| N70 | Ignition coil 1 with output stage |
| N127 | Ignition coil 2 with output stage |
| N291 | Ignition coil 3 with output stage |
| N292 | Ignition coil 4 with output stage |
| P | Spark plug connector |
| T121 | 121-pin connector |
| 15 | Earth point, on cylinder head |
| 85 | Earth connection 1, in engine compartment wiring harness |
| 281 | Earth point 1, engine prewiring harness |
| D206 | Connection 4 (87a) in engine prewiring harness |
Wiring Diagram VW JETTA NF 2017 - High-pressure sender - Air conditioning system relay - Climatronic control unit - Radiator fan control unit - Air conditioning system control unit - Engine control unit - Radiator fan
| G65 | High-pressure sender |
| J32 | Air conditioning system relay |
| J255 | Climatronic control unit |
| J293 | Radiator fan control unit |
| J301 | Air conditioning system control unit |
| J623 | Engine control unit |
| N25 | Air conditioning system magnetic clutch |
| T2er | 2-pin connector |
| T3 | 3-pin connector |
| T3a | 3-pin connector |
| T4 | 4-pin connector |
| T10 | 10-pin connector |
| T10s | 10-pin connector |
| T16n | 16-pin connector |
| T121 | 121-pin connector |
| V7 | Radiator fan |
| 13 | Earth point, on right in engine compartment |
| 317 | Earth connection 7, in engine compartment wiring harness |
| 671 | Earth point 1, on front of left longitudinal member |
| * | Only models with manual air conditioning system |
| *2 | Only models with Climatronic |
| *3 | Cross section depends on equipment |
Wiring Diagram VW JETTA NF 2017 - Hall sender - Throttle valve drive for electric throttle - Throttle valve drive angle sender 1 for electric throttle - Throttle valve drive angle sender 2 for electric throttle - Throttle valve module - Engine control unit
| G40 | Hall sender |
| G186 | Throttle valve drive for electric throttle |
| G187 | Throttle valve drive angle sender 1 for electric throttle |
| G188 | Throttle valve drive angle sender 2 for electric throttle |
| J338 | Throttle valve module |
| J623 | Engine control unit |
| T3a | 3-pin connector |
| T6 | 6-pin connector |
| T121 | 121-pin connector |
| D101 | Connection 1 in engine compartment wiring harness |
Wiring Diagram VW JETTA NF 2017 - Knock sensor 1 - Accelerator position sender - Accelerator position sender 2 - Engine control unit - Activated charcoal filter solenoid valve 1 - Camshaft control valve 1
| G61 | Knock sensor 1 |
| G79 | Accelerator position sender |
| G185 | Accelerator position sender 2 |
| J623 | Engine control unit |
| N80 | Activated charcoal filter solenoid valve 1 |
| N205 | Camshaft control valve 1 |
| T2d | 2-pin connector |
| T2e | 2-pin connector |
| T6q | 6-pin connector |
| T121 | 121-pin connector |
| D80 | Positive connection (87a, for activated charcoal filter system solenoid valve), in engine compartment wiring harness |
| * | Only models with 1.6l engine |
| *2 | Only models with 1.4l engine |
| *3 | Only models with "Low" equipment (AW0) |
Wiring Diagram VW JETTA NF 2017 - Engine speed sender - Coolant temperature sender - Intake manifold pressure sender - Engine control unit
| G28 | Engine speed sender |
| G42 | Intake air temperature sender |
| G62 | Coolant temperature sender |
| G71 | Intake manifold pressure sender |
| J623 | Engine control unit |
| T2b | 2-pin connector |
| T3b | 3-pin connector |
| T4b | 4-pin connector |
| T121 | 121-pin connector |
Wiring Diagram VW JETTA NF 2017 - Fuel gauge sender - Fuel system pressurisation pump - Fuel pump relay - Engine control unit
| G | Fuel gauge sender |
| G6 | Fuel system pressurisation pump |
| J17 | Fuel pump relay |
| J623 | Engine control unit |
| T5 | 5-pin connector |
| T121 | 121-pin connector |
| 43 | Earth point, lower part of right A-pillar |
| 199 | Earth connection 3, in dash panel wiring harness |
| 371 | Earth connection 6, in main wiring harness |
| B156 | Positive connection (30a), in interior wiring harness |
Wiring Diagram VW JETTA NF 2017 - Engine control unit - Injector - cylinder 1 - Injector - cylinder 2 - Injector - cylinder 3 - Injector - cylinder 4
| J623 | Engine control unit |
| N30 | Injector, cylinder 1 |
| N31 | Injector, cylinder 2 |
| N32 | Injector, cylinder 3 |
| N33 | Injector, cylinder 4 |
| T14a | 14-pin connector |
| T121 | 121-pin connector |
| D95 | Connection (injectors), in engine compartment wiring harness |
Wiring Diagram VW JETTA NF 2017 - Lambda probe - Lambda probe after catalytic converter - Engine control unit
| G39 | Lambda probe |
| G130 | Lambda probe after catalytic converter |
| J623 | Engine control unit |
| T4a | 4-pin connector |
| T4b | 4-pin connector |
| T121 | 121-pin connector |
| Z19 | Lambda probe heater |
| Z29 | Lambda probe 1 heater after catalytic converter |
| D189 | Connection (87a) in engine prewiring harness |
Wiring Diagram VW JETTA NF 2017 - Brake light switch - Clutch pedal switch - Brake pedal switch - Evaporator output temperature sender - Engine control unit
| F | Brake light switch |
| F36 | Clutch pedal switch |
| F47 | Brake pedal switch |
| G263 | Evaporator output temperature sender |
| J623 | Engine control unit |
| T4d | 4-pin connector |
| T4f | 4-pin connector |
| T121 | 121-pin connector |
| 417 | Earth connection 9, in engine compartment wiring harness |
| B350 | Positive connection 1 (87a) in main wiring harness |
| B633 | Connection (brake pedal switch), in main wiring harness |
| * | Only models with manual gearbox |
| *2 | Only models with manual air conditioning system |
| *3 | Cross section depends on equipment |
| *4 | Only models with "High" equipment (AW1) |
| *5 | Only models with "Low" equipment (AW0) |
Wiring Diagram VW JETTA NF 2017 - Oil pressure switch - Coolant shortage indicator sender - Buzzer and gong - Control unit in dash panel insert
| F1 | Oil pressure switch |
| G32 | Coolant shortage indicator sender |
| H3 | Buzzer and gong |
| J285 | Control unit in dash panel insert |
| K2 | Alternator warning lamp |
| K3 | Oil pressure warning lamp |
| K28 | Coolant temperature and coolant shortage warning lamp |
| K31 | Cruise control system warning lamp |
| K83 | Exhaust emissions warning lamp |
| T1g | Single connector |
| T2s | 2-pin connector |
| T14a | 14-pin connector |
| T32 | 32-pin connector |
| 410 | Earth connection 1 (sender earth) in main wiring harness |
Wiring Diagram VW JETTA NF 2017 - Fuel gauge - Rev. counter - Speedometer - Multifunction indicator - Control unit in dash panel insert - Trip counter
| G1 | Fuel gauge |
| G5 | Rev. counter |
| G21 | Speedometer |
| J119 | Multifunction indicator |
| J285 | Control unit in dash panel insert |
| K105 | Reserve fuel warning lamp |
| K132 | Electronic power control fault lamp |
| T32 | 32-pin connector |
| Y4 | Trip counter |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
| * | Only models with "High" equipment (AW1) |
| *2 | Only models with "Low" equipment (AW0) |
Can't find your car? Check -> DiagnostData.com!
Русский
