Wiring Diagram VW JETTA NF 2017 - Mechatronic unit for dual clutch gearbox
| G487 | Gear selector movement sensor 1 |
| G488 | Gear selector movement sensor 2 |
| J743 | Mechatronic unit for dual clutch gearbox |
| N433 | Valve 1 in sub-gearbox 1 |
| N434 | Valve 2 in sub-gearbox 1 |
| N435 | Valve 3 in sub-gearbox 1 |
| N436 | Valve 4 in sub-gearbox 1 |
| N437 | Valve 1 in sub-gearbox 2 |
| N438 | Valve 2 in sub-gearbox 2 |
| N439 | Valve 3 in sub-gearbox 2 |
| N440 | Valve 4 in sub-gearbox 2 |
| SB1 | Fuse 1 on fuse holder B |
| SB2 | Fuse 2 on fuse holder B |
| T25 | 25-pin connector |
| 150 | Earth connection 2 in automatic gearbox wiring harness |
| 641 | Earth point 3, left in engine compartment |
Wiring Diagram VW JETTA NF 2017 - Mechatronic unit for dual clutch gearbox - Fuse 13 on fuse holder C - Diagnostic connection
| G270 | Gearbox hydraulic pressure sender |
| G489 | Gear selector movement sensor 3 |
| G490 | Gear selector movement sensor 4 |
| G510 | Temperature sender in control unit |
| G612 | Gearbox input speed sender 2 |
| G617 | Clutch travel sender 1 |
| G618 | Clutch travel sender 2 |
| G632 | Gearbox input speed sender 1 |
| J743 | Mechatronic unit for dual clutch gearbox |
| SC13 | Fuse 13 on fuse holder C |
| T16 | 16-pin connector |
| T25 | 25-pin connector |
| U31 | Diagnostic connection |
| V401 | Hydraulic pump motor |
| D51 | Positive connection 1 (15), in engine compartment wiring harness |
Wiring Diagram VW JETTA NF 2017 - Selector lever - Onboard supply control unit - Data bus diagnostic interface - Selector lever sensors control unit - Engine control unit
| E313 | Selector lever |
| J519 | Onboard supply control unit |
| J533 | Data bus diagnostic interface |
| J587 | Selector lever sensors control unit |
| J623 | Engine control unit |
| SC20 | Fuse 20 on fuse holder C |
| T10s | 10-pin connector |
| T20 | 20-pin connector |
| T73b | 73-pin connector |
| T73c | 73-pin connector |
| T94 | 94-pin connector |
| 44 | Earth point, lower part of left A-pillar |
| 366 | Earth connection 1, in main wiring harness |
| 367 | Earth connection 2, in main wiring harness |
| 605 | Earth point, on top end of steering column |
| A19 | Connection (58d), in dash panel wiring harness |
| A116 | Connection 2 (58d), in dash panel wiring harness |
| B172 | Positive connection 4 (30), in interior wiring harness |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
| * | see applicable current flow diagram for engine |
Wiring Diagram VW JETTA NF 2017 - Selector lever - Selector lever sensors control unit - Selector lever position display
| E313 | Selector lever |
| J587 | Selector lever sensors control unit |
| T10t | 10-pin connector |
| Y26 | Selector lever position display |
| * | According to equipment |
Wiring Diagram VW JETTA NF 2017 - Selector lever - Selector lever locked in position P switch - Selector lever sensors control unit - Selector lever lock solenoid - Ignition key withdrawal lock solenoid
| E313 | Selector lever |
| F319 | Selector lever locked in position P switch |
| J587 | Selector lever sensors control unit |
| N110 | Selector lever lock solenoid |
| N376 | Ignition key withdrawal lock solenoid |
| T4dr | 4-pin connector |
| T10s | 10-pin connector |
| A167 | Positive connection 3 (30a) in dash panel wiring harness |
Не нашел автомобиль произведенный после 2014 года? смотри здесь -> DiagnostData.com!
English
