Wiring Diagram SEAT TOLEDO 2000 - Battery - starter - alternator - voltage regulator - ignition/starter switch - relief relay for x contact
| A | Battery (00532) |
| B | Starter |
| C | Alternator |
| C1 | Voltage regulator |
| D | Ignition/starter switch |
| J59 | Relief relay for x contact |
| S10 | Fuses in fuse box |
| S11 | Fuses in fuse box |
| S163 | Fuse -2- (30) in fuse holder/battery |
| S176 | Fuse -4- (30), in fuse holder/battery |
| S177 | Fuse -5- (30), in fuse holder/battery |
| S229 | Fuse in fuse box |
| T2k | 2 pin connector, on the engine |
| T4l | 4 pin connector, on the engine |
| T6l | 6 pin connector, brown, on the protective housing, on the water case, left side |
| A2 | Positive (+) connection (15), in dash panel wiring loom |
| A32 | Positive connection (30), in dash panel wiring loom |
| A41 | Positive (+) connection (50), in dash panel wiring loom |
| A98 | Positive connection -4- (30), in dash panel wiring harness |
| 500 | Screw connection -1- (30), on relay plate |
| 501 | Screw connection -2- (30), on relay plate |
| 502 | Screw connection -1- (30a), on relay plate |
| * | Only in vehicles with air conditioning |
Wiring Diagram SEAT TOLEDO 2000 - 4LV control unit (injection system) - coolant temperature sender - hall sender - ignition transformer - spark plug connector - flame plug
| G2 | Coolant temperature sender (01039) |
| G40 | Hall sender (00515-2113) |
| G62 | Sender for coolant temperature (00522-2312) |
| J448 | 4LV control unit (injection system) |
| N152 | Ignition transformer |
| P | Spark plug connector |
| Q | Flame plug |
| T4r | 4 pin connector |
| T6l | 6 pin connector, brown, on the protective housing, on the water case, left side |
| T14a | 14 pin connector, in the cable channel, left side |
| T80 | 80 pin connector |
| 85 | Earth connection -1-, in engine compartment wiring loom |
| 220 | Earth connection (sender earth), in engine wiring loom |
| A98 | Positive connection -4- (30), in dash panel wiring harness |
| A104 | Positive connection -2- (15), in dash panel wiring harness |
Wiring Diagram SEAT TOLEDO 2000 - 4LV control unit (injection system) - engine speed sender - intake air temperature sender
| G28 | Engine speed sender (00513-2111) |
| G42 | Intake air temperature sender (00523-2322) |
| G71 | Intake manifold pressure sender (00519-2222) |
| J255 | Control unit for Climatronic (01320) |
| J293 | Control unit for radiator fan (00831) |
| J448 | 4LV control unit (injection system) |
| N121 | Exhaust gas recirculation frequency valve |
| T3d | 3 pin connector, near the admission tube |
| T10 | 10 pin connector, orange, in the protective body of connections, in the water case, left side |
| T14 | 14 pin connector |
| T16b | 16 pin connector |
| T80 | 80 pin connector |
| 220 | Earth connection (sender earth), in engine wiring loom |
| D101 | Connection -1-, in engine compartment wiring loom |
Wiring Diagram SEAT TOLEDO 2000 - 4LV control unit (injection system) - throttle valve control unit - knock sensor I - throttle valve drive (electric throttle operation)
| G61 | Knock sensor I (00524-2142) |
| G186 | Throttle valve drive (electric throttle operation) |
| G187 | Angle sender -1- for throttle valve drive (electric throttle operation) |
| G188 | Angle sender -2- for throttle valve drive (electric throttle operation) |
| J104 | Control unit for ABS with EDS |
| J338 | Throttle valve control unit (01165) |
| J448 | 4LV control unit (injection system) |
| T2r | 2 pin connector, on the cylinder head, left side |
| T6n | 6 pin connector |
| T10d | 10 pin connector, green, in the protective body of connections, in the water case, left side |
| T25 | 25 pin connector |
| T47 | 47 pin connector |
| T80 | 80 pin connector |
| D101 | Connection -1-, in engine compartment wiring loom |
| D102 | Connection -2-, in engine compartment wiring loom |
Wiring Diagram SEAT TOLEDO 2000 - 4LV control unit (injection system) - accelerator position sender - accelerator pedal position sender -2- - injector - cylinder 1 - injector - cylinder 2 - injector - cylinder 3
| G79 | Accelerator position sender (00777-3131) |
| G185 | Accelerator pedal position sender -2- |
| J448 | 4LV control unit (injection system) |
| N30 | Injector, cylinder 1 (01249-4411) |
| N31 | Injector, cylinder 2 (01250-4412) |
| N32 | Injector, cylinder 3 (01251-4413) |
| N33 | Injector, cylinder 4 (01252-4414) |
| S232 | Fuse in fuse box |
| T6m | 6 pin connector, on the accelerator pedal |
| T10d | 10 pin connector, green, in the protective body of connections, in the water case, left side |
| T10h | 10 pin connector, blue, in the protective body of connections, in the water case, left side |
| T14a | 14 pin connector, in the cable channel, left side |
| T80 | 80 pin connector |
| D95 | Connection (injectors), in engine compartment wiring loom |
Wiring Diagram SEAT TOLEDO 2000 - 4LV control unit (injection system) - lambda probe - lambda probe heater
| F | Brake light switch |
| G39 | Lambda probe |
| J448 | 4LV (injection system) control unit |
| Z19 | Lambda probe heater |
| T6q | 6-pin connector, on exhaust pipe |
| T10d | 10-pin connector, green, in protective housing for connectors, in plenum chamber, left |
| T10e | 10-pin connector, black, in protective housing for connectors, in plenum chamber, left |
| T80 | 80-pin connector |
| 10 | Earth point, in plenum chamber |
| 131 | Earth connection -2-, in engine compartment wiring harness |
| * | Only models with cruise control system |
Wiring Diagram SEAT TOLEDO 2000 - 4LV (injection system) control unit - lambda probe after catalyst - lambda probe 1 heater - downstream of catalytic converter - fuel pump relay
| G130 | Lambda probe after catalyst |
| J17 | Fuel pump relay |
| J234 | Airbag control unit |
| J448 | 4LV (injection system) control unit |
| N80 | Activated charcoal filter system solenoid valve 1 (pulsed) |
| Z29 | Lambda probe 1 heater, downstream of catalytic converter |
| T4p | 4-pin connector, centre in engine compartment |
| T6l | 6-pin connector, brown, in protective housing for connectors, in plenum chamber, left |
| T10 | 10-pin connector, orange, in protective housing for connectors, in plenum chamber, left |
| T75 | 75-pin connector, behind the centre console |
| T80 | 80-pin connector |
| A27 | Connection (speed signal), in dash panel wiring harness |
| A125 | Connection (crash signal), in dash panel wiring harness |
| E30 | Connection (87a), in engine wiring harness |
| * | Only models with multi-function display |
| ** | Wire W for self-diagnosis |
Wiring Diagram SEAT TOLEDO 2000 - Fuel gauge sender - fuel pump (pre-supply pump) - coolant shortage indicator sender
| G | Fuel gauge sender (00771-3113) |
| G6 | Fuel pump (pre-supply pump) |
| G32 | Coolant shortage indicator sender |
| S228 | Fuse in fuse holder |
| S234 | Fuse in fuse holder |
| S243 | Fuse in fuse holder |
| T6l | 6-pin connector, brown, in the connec. protective housing, in the plenum chamber, left side |
| T14a | 14-pin connector, in the wire channel, left side |
| 135 | Earth connection -2-, in dash panel wiring harness |
| 269 | Earth connection (sender earth) -1-, in dash panel wiring harness |
| 504 | Screw connection -1- (87F), on relay plate |
| A99 | Connection -1- (87), in dash panel wiring harness |
| A100 | Connection -2- (87), in dash panel wiring harness |
| E30 | Connection (87a), in engine wiring harness |
Wiring Diagram SEAT TOLEDO 2000 - Control unit with display in dash panel insert - oil pressure switch - speedometer sender - oil pressure warning buzzer - alternator warning lamp
| F1 | Oil pressure switch |
| G22 | Speedometer sender (01086)(Hall sender on gearbox) |
| H11 | Oil pressure warning buzzer |
| J285 | Control unit with display in dash panel insert (01317) |
| K2 | Alternator warning lamp |
| K3 | Oil pressure warning lamp (00755) |
| K28 | Coolant temperature/coolant shortage warning lamp |
| K83 | Exhaust emissions warning lamp |
| K132 | Electronic power control fault lamp |
| S7 | Fuse in relay plate/fuse box |
| T14a | 14-pin connector, in wire channel, left side |
| T32 | 32-pin connector, blue, in dash panel |
| T32a | 32-pin connector, green, in dash panel |
| 10 | Earth point, in plenum chamber |
| 85 | Earth connection -1-, in engine compartment wiring harness |
| B163 | Positive connection -1- (15), in interior wiring harness |
| D51 | Positive (+) connection -1- (15), in engine compartment wiring harness |
| * | Self-diagnosis line W |
Wiring Diagram SEAT TOLEDO 2000 - Control unit with display in dash panel insert - multi-function display - multi-function display call-up button - multi-function display - memory switch
| E86 | Multi-function display call-up button |
| E109 | Multi-function display, memory switch |
| G1 | Fuel gauge (00664) |
| G3 | Coolant temperature gauge |
| G5 | Rev. counter (00662) |
| G21 | Speedometer (00663) |
| J119 | Multi-function display |
| J255 | Climatronic control unit (01320) |
| J285 | Control unit with display in dash panel insert (01317) |
| K105 | Reserve fuel warning lamp (01082) |
| T6d | 6-pin connector |
| T12d | 12-pin connector, in the Climatronic |
| T16b | 16-pin connector |
| T32 | 32-pin connector, blue, in dash panel |
| T32a | 32-pin connector, green, in dash panel |
| A13 | Connection (door contact switch), in dash panel wiring harness |
| A27 | Connection (speed signal), in dash panel wiring harness |
| * | Only vehicles with M.F.I. |
Can't find your car? Check -> DiagnostData.com!
Русский
