Wiring Diagram SEAT INCA 2002 - Battery - starter - alternator - voltage regulator
| A | Battery |
| B | Starter |
| C | Alternator |
| C1 | Voltage regulator |
| D | Ignition/starter switch |
| J362 | Immobilizer control unit |
| SA1 | Fuse -1- fuse box/battery |
| SA2 | Fuse -2- fuse box/battery |
| SA4 | Fuse -4- fuse box/battery |
| SA5 | Fuse -5- fuse box/battery |
| T5d | 5-pin connector, on engine, near gearbox |
| 1 | Earth strap, battery - body |
| 2 | Earth strap, gearbox - body |
| D50 | Positive (+) connection (30), in engine compartment wiring harness |
| * | Only models with additional heater |
Wiring Diagram SEAT INCA 2002 - Diesel direct injection system control unit - kick-down switch - idling switch - accelerator pedal position sender - intake manifold temperature sender
| F8 | Kick-down switch |
| F60 | Idling switch |
| G70 | Air mass meter |
| G71 | Intake manifold pressure sender |
| G79 | Accelerator pedal position sender |
| J248 | Diesel direct injection system control unit |
| J362 | Immobilizer control unit |
| 201 | Earth connection -5-, in engine compartment wiring harness |
| D136 | Positive (+) connection -2- (15a), in engine compartment wiring harness |
| * | Only models with engine codes ALH |
| ** | Does not apply to models with engine codes ALH |
Wiring Diagram SEAT INCA 2002 - Diesel direct injection system control unit - engine speed sender - needle lift sender - shut-off valve
| G28 | Engine speed sender |
| G42 | Intake air temperature sender |
| G71 | Intake manifold pressure sender |
| G80 | Needle lift sender |
| J248 | Diesel direct injection system control unit |
| N75 | Charge pressure control solenoid valve |
| N109 | Fuel shut-off valve |
| T2s | 2-pin connector, self-diagnosis |
| T3j | 3-pin connector |
| T10y | 10-pin connector, black, on lower part of left A-pillar |
| D110 | Connection -8-, in engine compartment wiring harness |
| * | Only models with engine codes ALH |
Wiring Diagram SEAT INCA 2002 - Diesel direct injection system control unit - fuel temperature sender - modulating piston movement sender - metering adjuster - exhaust gas recirculation valve
| F129 | Air conditioner pressure switch |
| G81 | Fuel temperature sender |
| G149 | Modulating piston movement sender |
| J248 | Diesel direct injection system control unit |
| J293 | Radiator fan control unit |
| J362 | Immobilizer control unit |
| N18 | Exhaust gas recirculation valve |
| N146 | Metering adjuster |
| N239 | Intake manifold flap change-over valve |
| T10y | 10-pin connector, black, on lower part of left A-pillar |
| D80 | Positive (+) connection (87 a - for activated charcoal filter system solenoid valve), in engine compartment wiring harness |
| D107 | Connection -5-, in engine compartment wiring harness |
| F25 | Connection -1-, in diesel direct injection system wiring harness |
| * | Only models with air conditioner |
| ** | Only models with engine codes AYQ |
| *** | Only models with engine codes ALH |
| **** | Wire W for self-diagnosis |
Wiring Diagram SEAT INCA 2002 - Diesel direct injection system control unit - intake manifold preheating heater element
| J248 | Diesel direct injection system control unit |
| J317 | Terminal 30 voltage supply relay |
| J325 | Coolant heater element relay |
| J359 | Low heat output relay |
| J360 | High heat output relay |
| N51 | Intake manifold preheating heater element |
| Q7 | Coolant heating elements |
| S109 | Coolant heater element fuse |
| 12 | Earth point, in engine compartment, left |
| 85 | Earth connection -1-, in engine compartment wiring harness |
| D103 | Connection -3-, in engine compartment wiring harness |
| D114 | Connection -12-, in engine compartment wiring harness |
| * | Only models with additional heater |
| ** | Only models without additional heater |
| *** | Only northern countries |
Wiring Diagram SEAT INCA 2002 - Diesel direct injection system control unit - brake light switch - brake pedal switch - coolant temperature sender
| F | Brake light switch |
| F36 | Clutch pedal switch |
| F63 | Brake pedal switch |
| G2 | Coolant temperature sender |
| G62 | Coolant temperature sender |
| J248 | Diesel direct injection system control unit |
| M21 | Brake and tail light bulb, left |
| M22 | Brake and tail light bulb, right |
| M25 | High level brake light bulb |
| N108 | Commencement of injection valve |
| TV2 | Terminal 30 junction box |
| T10y | 10-pin connector, black, on lower part of left A-pillar |
| D52 | Positive (+) connection (15a), in engine compartment wiring harness |
| D73 | Positive (+) connection (54), in engine compartment wiring harness |
| D114 | Connection -12-, in engine compartment wiring harness |
Wiring Diagram SEAT INCA 2002 - Oil pressure switch - fuel gauge sender - speedometer sender - fuel pump (pre-supply pump) - glow plugs (engine) - glow plug relay
| F1 | Oil pressure switch |
| G | Fuel gauge sender |
| G22 | Speedometer sender |
| J52 | Glow plugs relay |
| Q6 | Glow plugs - (engine) |
| T1l | Single connector, brown, behind relay plate |
| T1m | Single connector, brown, behind relay plate |
| T2b | 2-pin connector |
| TV7 | Terminal 31 junction box |
| 30 | Earth point -1-, next to relay plate |
| D108 | Connection -6-, in engine compartment wiring harness |
| F31 | Connection (glow plugs - engine), in diesel direct injection system wiring harness |
Wiring Diagram SEAT INCA 2002 - Control unit with display in dash panel insert - fuel gauge - coolant temperature gauge - speedometer - diagnostic connector - rev. counter
| G1 | Fuel gauge |
| G3 | Coolant temperature gauge |
| G5 | Rev. counter |
| J285 | Control unit with display in dash panel insert |
| K2 | Alternator warning lamp |
| K3 | Oil pressure warning lamp |
| K28 | Coolant temperature warning lamp/coolant shortage warning lamp |
| K29 | Glow period warning lamp |
| T4k | 4-pin connector, behind dash panel insert |
| A49 | Connection -1-, in dash panel wiring harness |
Didn't find a car made after 2014? Look here -> DiagnostData.com!
Русский
