SKODA SUPERB II 2011 — Anti-lock brake system (ABS) with differential lock (EDL), traction control system (TCS), electronic stabilisation program (ESP), hill hold control (HHC) — MK60 EC, As of November 2010 . Wiring diagrams, Pin Connector, Location

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - fuse holder C in the dash panel

E226	Tyre pressure monitor button
J104	ABS control unit
J519	Vehicle voltage control unit
SC2	Fuse 2 on fuse holder C
T47a	47-pin connector, at ABS control unit
B281	Positive connection 5 (15a) in main wiring harness
*1	for vehicles with tyre pressure monitor

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - fuse holder B on the E box

J104	ABS control unit
J519	Vehicle voltage control unit
N99	ABS inlet valve, front right
N100	ABS outlet valve, front right
N101	ABS inlet valve, front left
N102	ABS outlet valve, front left
SB2	Fuse 2 on fuse holder B
SB4	Fuse 4 on fuse holder B
SB25	Fuse 25 on fuse holder B
SB48	Fuse 48 on fuse holder B
T40a	40-pin connector, at the E box
T47a	47-pin connector, at ABS control unit
V64	ABS hydraulic pump
43	Earth point lower part of right A-pillar
640	Earth point 2 on left in engine compartment
*1	not valid for 3.6 ltr./191 kW
*2	valid for 3.6 ltr./191 kW
*3	only for vehicles with left-hand drive
*4	only for vehicles with right-hand drive

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - Speed sensor

G44	Rear right speed sensor
G45	Front right speed sensor
G46	Rear left speed sensor
G47	Front left speed sensor
J104	ABS control unit
J519	Vehicle voltage control unit
N133	ABS inlet valve, rear right
N134	ABS inlet valve, rear left
N135	ABS outlet valve, rear right
N136	ABS outlet valve, rear left
T47a	47-pin connector, at ABS control unit

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - TCS and ESP button

E256	TCS and ESP button
F	Brake light switch
G201	Brake pressure sender 1
J104	ABS control unit
J519	Vehicle voltage control unit
L115	Bulb for lighting of stabilising program button
T4c	4-pin connector, at brake pedal switch
T6v	6-pin connector, at TCS and ESP button
T47a	47-pin connector, at ABS control unit
374	Earth connection 9 in main wiring harness
B335	Connection 1 (54) in main wiring harness
B340	Connection 1 (58d) in main wiring harness

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - ESP sensor unit - vacuum sensor

G200	Lateral acceleration sender
G202	Yaw rate sender
G251	Longitudinal acceleration sender
G419	ESP sensor unit
G608	Vacuum sensor
J104	ABS control unit
J519	Vehicle voltage control unit
N225	Vehicle stabilising program switch valve -1-
N226	Vehicle stabilising program switch valve -2-
N227	Vehicle stabilising program switch high pressure valve -1-
N228	Vehicle stabilising program switch high pressure valve -2-
T4bm	4-pin connector, at vacuum sensor
T47a	47-pin connector, at ABS control unit
*1	for vehicles with four-wheel drive or with hill hold control (HHC)
*2	depending on equipment

Wiring Diagram SKODA SUPERB II 2011 - ABS control unit - data bus diagnostic interface - dash panel insert

J104	ABS control unit
J285	Control unit in dash panel insert
J519	Vehicle voltage control unit
J533	Data bus diagnostic interface
K	Dash panel insert
K47	ABS warning light
K155	ESP and TCS warning light
K216	ESP and TCS warning light 2
T20c	20-pin connector, at data bus diagnostic interface
T32a	32-pin connector, at dash panel insert
T47a	47-pin connector, at ABS control unit
B383	Connection 1 (drive train CAN bus High) in main wiring harness
B390	Connection 1 (drive train CAN bus Low) in main wiring harness
B708	Connection 1 (CAN bus dash panel insert High) in main wiring harness
B709	Connection 1 (CAN bus dash panel insert Low) in main wiring harness