Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
Wiring Diagram SKODA FABIA II 2012 - Starter - Alternator with voltage regulator - Fuse holder A
| A | Battery |
| B | Starter |
| CX1 | Alternator with voltage regulator |
| D | Ignition/starter switch |
| J519 | Onboard supply control unit |
| SA | Fuse holder A |
| SA1 | Fuse 1 in fuse holder A |
| SA5 | Fuse 5 in fuse holder A |
| T6o | 6-pin connector |
| T8d | 8-pin connector, front left in engine compartment |
| T73b | 73-pin connector |
| B276 | Positive connection (50), in main wiring harness |
| B315 | Positive connection 1 (30a) in main wiring harness |
| B344 | Connection 1 (61), in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Radiator fan control unit - Radiator fan - Radiator fan on right of radiator
| J293 | Radiator fan control unit |
| J519 | Onboard supply control unit |
| T2g | 2-pin connector, on radiator fan |
| T4ap | 4-pin connector |
| V7 | Radiator fan |
| V35 | Radiator fan on right of radiator |
| 380 | Earth connection 15, in main wiring harness |
| B315 | Positive connection 1 (30a) in main wiring harness |
| * | Only models with two radiator fans |
Wiring Diagram SKODA FABIA II 2012 - Fuse holder B
| J329 | Terminal 15 voltage supply relay |
| J519 | Onboard supply control unit |
| SB | Fuse holder B |
| SB3 | Fuse 3 on fuse holder B |
| SB7 | Fuse 7 on fuse holder B |
| SB8 | Fuse 8 on fuse holder B |
| SB16 | Fuse 16 on fuse holder B |
| SB46 | Fuse 46 on fuse holder B |
| T14a | 14-pin connector, front left in engine compartment |
| B275 | Positive connection (87), in main wiring harness |
| B278 | Positive connection 2 (15a) in main wiring harness |
| B280 | Positive connection 4 (15a) in main wiring harness |
| B316 | Positive connection 2 (30a) in main wiring harness |
| B319 | Positive connection 5 (30a) in main wiring harness |
| * | Only models with extended servicing intervals (ESI) |
| *2 | According to equipment |
Wiring Diagram SKODA FABIA II 2012 - Fuse holder B
| J519 | Onboard supply control unit |
| SB | Fuse holder B |
| SB28 | Fuse 28 on fuse holder B |
| SB29 | Fuse 29 on fuse holder B |
| SB30 | Fuse 30 on fuse holder B |
| SB31 | Fuse 31 on fuse holder B |
| SB32 | Fuse 32 on fuse holder B |
| SB33 | Fuse 33 on fuse holder B |
| SB34 | Fuse 34 on fuse holder B |
| B275 | Positive connection (87), in main wiring harness |
| B354 | Positive connection 5 (87a) in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Automatic glow period control unit - Engine control unit - Glow plug 1 - Glow plug 2 - Glow plug 3
 ">J179 | "> Automatic glow period control unit |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| Q10 | Glow plug 1 |
| Q11 | Glow plug 2 |
| Q12 | Glow plug 3 |
| T14a | 14-pin connector, front left in engine compartment |
| T73b | 73-pin connector |
| T94a | 94-pin connector |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Engine control unit
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T14a | 14-pin connector, front left in engine compartment |
| T94a | 94-pin connector |
| 281 | Earth point 1, engine prewiring harness |
| 376 | Earth connection 11, in main wiring harness |
| 377 | Earth connection 12, in main wiring harness |
| B353 | Positive connection 4 (87a) in main wiring harness |
| * | Only models with extended servicing intervals (ESI) |
| *2 | According to equipment |
Wiring Diagram SKODA FABIA II 2012 - Clutch pedal switch - Brake pedal switch - Accelerator position sender - Engine control unit
| F | Brake light switch |
| F36 | Clutch pedal switch |
| F47 | Brake pedal switch |
| G79 | Accelerator position sender |
| G185 | Accelerator position sender 2 |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T4d | 4-pin connector |
| T4h | 4-pin connector |
| T6u | 6-pin connector |
| T94a | 94-pin connector |
| B335 | Connection 1 (54), in main wiring harness |
| B355 | Positive connection 6 (87a) in main wiring harness |
| * | Only models with manual gearbox |
Wiring Diagram SKODA FABIA II 2012 - Intake air temperature sender - Diesel direct injection system relay - Engine control unit
| G42 | Intake air temperature sender |
| J322 | Diesel direct injection system relay |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T4at | 4-pin connector |
| T60a | 60-pin connector |
| T94a | 94-pin connector |
| 458 | Earth point 3, engine prewiring harness |
| B317 | Positive connection 3 (30a) in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Charge pressure sender - Knock sensor 1 - Engine control unit
| G31 | Charge pressure sender |
| G61 | Knock sensor 1 |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T4an | 4-pin connector |
| T60a | 60-pin connector |
| 458 | Earth point 3, engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Engine speed sender - Hall sender - Radiator outlet coolant temperature sender - Engine control unit
| G28 | Engine speed sender |
| G40 | Hall sender |
| G83 | Radiator outlet coolant temperature sender |
| J301 | Air conditioning system control unit |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T3j | 3-pin connector |
| T3m | 3-pin connector |
| T14a | 14-pin connector, front left in engine compartment |
| T16e | 16-pin connector |
| T60a | 60-pin connector |
| T94a | 94-pin connector |
| B696 | Connection 1 (air conditioning) in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Oil level and oil temperature sender - Engine control unit - Coolant circulation pump 2
| G266 | Oil level and oil temperature sender |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T3f | 3-pin connector |
| T3w | 3-pin connector |
| T14a | 14-pin connector, front left in engine compartment |
| T60a | 60-pin connector |
| V178 | Coolant circulation pump 2 |
| * | Only models with extended servicing intervals (ESI) |
Wiring Diagram SKODA FABIA II 2012 - Coolant temperature sender - Fuel temperature sender - Engine control unit - Injector - cylinder 1 - Injector - cylinder 2 - Injector - cylinder 3
| G62 | Coolant temperature sender |
| G81 | Fuel temperature sender |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| N30 | Injector, cylinder 1 |
| N31 | Injector, cylinder 2 |
| N32 | Injector, cylinder 3 |
| T60a | 60-pin connector |
| 283 | Earth point 2, engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Air mass meter - Engine control unit - Charge pressure control solenoid valve - Exhaust gas recirculation cooler changeover valve
| G70 | Air mass meter |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| N75 | Charge pressure control solenoid valve |
| N345 | Exhaust gas recirculation cooler changeover valve |
| T4am | 4-pin connector |
| T14a | 14-pin connector, front left in engine compartment |
| T60a | 60-pin connector |
| T94a | 94-pin connector |
| D196 | Connection 2 (87a) in engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Lambda probe - Engine control unit
| G39 | Lambda probe |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T6aj | 6-pin connector |
| T94a | 94-pin connector |
| Z19 | Lambda probe heater |
Wiring Diagram SKODA FABIA II 2012 - Fuel pressure sender - Position sender for charge pressure positioner - Engine control unit
| G247 | Fuel pressure sender |
| G581 | Position sender for charge pressure positioner |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T3u | 3-pin connector |
| T3z | 3-pin connector |
| T60a | 60-pin connector |
| 474 | Earth connection (sender earth) in engine prewiring harness |
| D141 | Connection (5V) in engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Exhaust gas recirculation potentiometer - Intake manifold flap potentiometer - Engine control unit - Exhaust gas recirculation valve - Intake manifold flap motor - Exhaust gas recirculation control motor
| G212 | Exhaust gas recirculation potentiometer |
| G336 | Intake manifold flap potentiometer |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| N18 | Exhaust gas recirculation valve |
| T5g | 5-pin connector |
| T6ak | 6-pin connector |
| T60a | 60-pin connector |
| V157 | Intake manifold flap motor |
| V338 | Exhaust gas recirculation control motor |
| 474 | Earth connection (sender earth) in engine prewiring harness |
| D141 | Connection (5V) in engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Throttle valve potentiometer - Throttle valve module - Engine control unit - Fuel pressure regulating valve - Fuel metering valve
| G69 | Throttle valve potentiometer |
| J338 | Throttle valve module |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| N276 | Fuel pressure regulating valve |
| N290 | Fuel metering valve |
| T5c | 5-pin connector |
| T14a | 14-pin connector, front left in engine compartment |
| T60a | 60-pin connector |
| 474 | Earth connection (sender earth) in engine prewiring harness |
| D141 | Connection (5V) in engine prewiring harness |
Wiring Diagram SKODA FABIA II 2012 - Exhaust gas temperature sender 1 - Engine control unit - Heater element for crankcase breather
| G235 | Exhaust gas temperature sender 1 |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| N79 | Heater element for crankcase breather |
| T2d | 2-pin connector, black |
| T94a | 94-pin connector |
| 327 | Earth connection (sender earth), in engine compartment wiring harness |
| B352 | Positive connection 3 (87a) in main wiring harness |
| * | Special equipment |
Wiring Diagram SKODA FABIA II 2012 - Fuel gauge sender - Fuel system pressurisation pump - Fuel pump relay - Engine control unit
| G | Fuel gauge sender |
| G6 | Fuel system pressurisation pump |
| J17 | Fuel pump relay |
| J519 | Onboard supply control unit |
| J623 | Engine control unit |
| T5a | 5-pin connector |
| T94a | 94-pin connector |
| 370 | Earth connection 5, in main wiring harness |
| 410 | Earth connection 1 (sender earth) in main wiring harness |
| B352 | Positive connection 3 (87a) in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Fuel gauge - Dash panel insert
| G1 | Fuel gauge |
| J285 | Control unit in dash panel insert |
| J519 | Onboard supply control unit |
| K | Dash panel insert |
| K105 | Reserve fuel warning lamp |
| T32a | 32-pin connector |
| 410 | Earth connection 1 (sender earth) in main wiring harness |
Wiring Diagram SKODA FABIA II 2012 - Oil pressure switch - Speedometer - Speedometer sender - Dash panel insert - Trip counter
| F1 | Oil pressure switch |
| G21 | Speedometer |
| G22 | Speedometer sender |
| J217 | Automatic gearbox control unit |
| J285 | Control unit in dash panel insert |
| J519 | Onboard supply control unit |
| K | Dash panel insert |
| K3 | Oil pressure warning lamp |
| K29 | Glow period warning lamp |
| K38 | Oil level warning lamp |
| K83 | Exhaust emissions warning lamp |
| T3l | 3-pin connector |
| T14a | 14-pin connector, front left in engine compartment |
| T32a | 32-pin connector |
| T52b | 52-pin connector |
| Y4 | Trip counter |
| B464 | Connection (speed signal), in main wiring harness |
| * | Only models with extended servicing intervals (ESI) |
| *2 | According to equipment |
SKODA FABIA II 2012
SKODA FABIA II 2012 Overview of the control units
| Overview of the control units |
| 1 - | Air conditioning system control unit -J301- |
| q | Pin assignment: Air conditioning system control unit -J301- |
| 2 - | Radio -R- |
| q | Pin assignment |
| q | Pin assignment for radio pre-installation for aftermarket units |
| 3 - | ABS control unit -J104- |
| q | Fitting location |
| q | Pin assignment: |
| 4 - | Engine control unit -J623- |
| q | Fitting location |
| q | 52-pin + 28-pin assignment |
| q | 94-pin + 60-pin assignment |
| 5 - | Radiator fan control unit -J293- |
| q | Fitting location |
| q | Pin assignment |
| 6 - | Automatic glow period control unit -J179- |
| q | Fitting location |
| 7 - | Lambda probe after catalytic converter -G130- |
| q | Fitting location |
| q | Pin assignment |
| 8 - | Lambda probe -G39- |
| q | Fitting location |
| q | Pin assignment |
| 9 - | Airbag control unit -J234- |
| q | Fitting location |
| q | Pin assignment: |
| 10 - | Power steering control unit -J500- |
| q | Fitting location |
| 11 - | Control unit in dash panel insert -J285- / Immobilizer control unit -J362- |
| q | Pin assignment |
| q | Warning light control in dash panel insert as of August 2010 |
| q | Warning light control in dash panel insert as of August 2011 |
| q | Display control in dash panel insert |
| 12 - | Onboard control unit -J519- |
| q | Fitting location |
| q | Pin assignment |
| 13 - | Light switch -E1- |
| q | Fitting location |
| q | Pin assignment |
| 14 - | Headlight range control adjuster -E102- |
| q | Fitting location |
| q | Pin assignment |
| 15 - | Ignition starter switch -D- |
| q | Pin assignment as of August 2010 |
| q | Pin assignment as of August 2011 |
| 16 - | Left steering column switch -EX19- / Right steering column switch -EX20- / Coil -F350- |
| q | Fitting location |
| q | Pin assignment |
|
| A | - | 6-pin connector, at wiring harness - T6af |
| B | - | 8-pin connector, at wiring harness - T8p |
| C | - | 8-pin connector, at wiring harness - T8n |
|
| A | - | 6-pin connector, at wiring harness - T6ae |
| B | - | 8-pin connector, at wiring harness - T8p |
| C | - | 8-pin connector, at wiring harness - T8n |
|
| 1 | - | T8a/50 |
| 2 | - | T8a/75 |
| 3 | - | T8a/30 |
| 4 | - | T8a/P |
| 5 | - | T8a/50b |
| 6 | - | T8a/15 |
| 7 | - | T8a/30 |
| 8 | - | T8a/86s |
|
| 1 | - | T6o/50 |
| 2 | - | T6o/15 |
| 3 | - | T6o/30 |
| 4 | - | T6o/86s |
| 5 | - | T6o/30 |
| 6 | - | T6o/75 |
|
| Pin assignment: |
| A | - | Left steering column switch -EX19- / Right steering column switch -EX20- / Coil -F350- |
| B | - | 41-pin connector, at wiring harness - T41a |
|
|
| A | - | Headlight range control adjuster -E102- |
| B | - | 8-pin connector, at wiring harness - T8b |
|
|
| A | - | Light switch -E1- |
| B | - | 17-pin connector, at wiring harness - T17a |
| Control unit in dash panel insert -J285- / Immobilizer control unit -J362- |
| Pin assignment: |
| A | - | Control unit in dash panel insert -J285- / Immobilizer control unit -J362- |
| B | - | 32-pin connector, at wiring harness - T32a |
| 32-pin connector -T32a- : |
| 1 | - | Fuel gauge sender -G- |
| 2 | - | Fuel gauge sender -G- |
| 3 | - | not assigned |
| 4 | - | not assigned |
| 5 | - | not assigned |
| 6 | - | not assigned |
| 7 | - | Immobilizer reading coil -D2- |
| 8 | - | Immobilizer reading coil -D2- |
| 9 | - | Speed signal - Ouput |
| 10 | - | Speedometer sender -G22- |
| 11 | - | Oil level and oil temperature sender -G266- |
| 12 | - | not assigned |
| 13 | - | Rear fog light warning light -K13- |
| 14 | - | Main beam warning light -K1- |
| 15 | - | not assigned |
| 16 | - | Terminal 31 - Input |
| 17 | - | Windscreen washer fluid level sender -G33- |
| 18 | - | Coolant shortage indicator sender -G32- |
| 19 | - | Ambient temperature sensor -G17- |
| 20 | - | Terminal 31 (sender mass) - Output |
| 21 | - | Multi-function display -J119- |
| - | Function selection switch -E91- | |
| 22 | - | Multi-function display -J119- |
| - | Function selection switch -E91- | |
| 23 | - | Multi-function display -J119- |
| - | Reset button -E92- | |
| 24 | - | not assigned |
| 25 | - | Handbrake warning switch -F9- |
| 26 | - | Brake fluid level warning contact -F34- |
| 27 | - | Oil pressure switch -F1- |
| 28 | - | Drive train CAN bus, high |
| 29 | - | Drive train CAN bus, low |
| 30 | - | Fog light warning light -K17- |
| 31 | - | Terminal 15 - Input |
| 32 | - | Terminal 30 - Input |
| Warning light control in dash panel insert - K, as of August 2011 |
| Warning light | Signal source |
| Main beam warning light -K1- | T32a/14 |
| Alternator warning light -K2- | CAN bus Onboard control unit -J519- |
| Oil pressure warning light -K3- | T32a/27 |
| Brake system warning light -K118- | T32a/26, CAN bus ABS control unit -J104- |
| Handbrake warning light -K14- | T32a/25 |
| Rear fog light warning light -K13- | T32a/13 |
| Fog light warning light -K17- | T32a/30 |
| Seat belt warning light -K19- | CAN bus Airbag control unit -J234- |
| Coolant temperature and coolant shortage indicator warning light -K28- | T32a/18, CAN bus engine control unit -J623- |
| Glow period warning light -K29- | CAN bus Engine control unit -J623- |
| Oil level warning light -K38- | T32a/11 |
| ABS warning light -K47- | CAN bus ABS control unit -J104- |
| Dipped beam and rear lights warning light -K60- | CAN bus Onboard control unit -J519- |
| CCS warning light -K31- | CAN bus Onboard control unit -J519- |
| Left turn signal warning light -K65- | CAN bus Onboard control unit -J519- |
| Airbag warning light -K75- | CAN bus Airbag control unit -J234- |
| Exhaust emissions warning lamp -K83- | CAN bus Engine control unit -J623- |
| Electro/mechanical power steering warning light -K161- | CAN bus Onboard control unit -J519- |
| Right turn signal warning light -K94- | CAN bus Onboard control unit -J519- |
| Fuel reserve warning light -K105- | T32a/1, T32a/2 |
| Washer fluid low warning light -K106- | T32a/17 |
| Rear lid open warning light -K116- | CAN bus Onboard control unit -J519- |
| Electronic power control fault lamp -K132- | CAN bus Engine control unit -J623- |
| Door open warning light -K166- | CAN bus Onboard control unit -J519- |
| Selector lever lock warning light -K169- | CAN bus Automatic gearbox control unit -J217- , Double clutch gearbox mechatronics -J743- |
| Bonnet open warning light -K171- | CAN bus Onboard control unit -J519- |
| Warning light for tyre pressure display -K220- | CAN bus ABS control unit -J104- |
| Diesel particle filter warning light -K231- | CAN bus Engine control unit -J623- |
| Bulb failure warning light -K170- | CAN bus Onboard control unit -J519- |
| Warning light for engine cold -K249- | CAN bus Engine control unit -J623- |
| Display control in dash panel insert K |
| Display | Signal source |
| Fuel gauge -G1- | T32a/1, T32a/2 |
| Coolant temperature gauge -G3- | CAN bus Engine control unit -J623- |
| Rev. counter -G5- | CAN bus Engine control unit -J623- |
| Speedometer -G21- | T32a/10, CAN bus ABS control unit -J104- |
| Buzzer and gong -H3- | CAN bus Control unit in dash panel insert -J285- |
| Digital clock -Y2- | CAN bus Control unit in dash panel insert -J285- |
| Odometer display -Y4- | CAN bus Control unit in dash panel insert -J285- |
| Multi-function display -J119- | T32a/19, 21, 22, 23, CAN bus Engine control unit -J623- , Control unit in dash panel insert -J285- |
| Selector lever position indicator -Y6- | CAN bus Automatic gearbox control unit -J217- , Double clutch gearbox mechatronics -J743- |
|
|
| Pin assignment: |
| A | - | 73-pin connector (black) - T73a |
| B | - | 73-pin connector (white) - T73b |
| 73-pin connector -T73a- (black): |
| 1 | - | not assigned |
| 2 | - | not assigned |
| 3 | - | not assigned |
| 4 | - | Output for Interior light (31) |
| 5 | - | not assigned |
| 6 | - | not assigned |
| 7 | - | Input of light switch -E1- (fog lights) |
| 8 | - | not assigned |
| 9 | - | not assigned |
| 10 | - | Output for central locking motor in rear lid -V53- |
| 11 | - | Output for central locking motor in driver door -V56- , central locking motor in front passenger door -V57- , central locking motor in rear left door, lock -V214- , central locking motor in rear right door, lock -V215- |
| 12 | - | Output for central locking motor in driver door -V56- , motor for SAFE function of central locking in driver door -V161- |
| 13 | - | Output for motor for SAFE function of central locking in driver door -V161- , motor for SAFE function of central locking in front passenger door -V162- , motor for SAFE function of central locking in rear left door -V163- , motor for SAFE function of central locking in rear right door -V164- |
| 14 | - | Input (31) - for central locking |
| 15 | - | Output for central locking motor in front passenger door -V57- , motor for SAFE function of central locking in front passenger door -V162- , central locking motor in rear left door, lock -V214- , central locking motor in rear right door, lock -V215- |
| 16 | - | Input (30) - for central locking |
| 17 | - | Input of central locking lock unit, rear left -F222- |
| 18 | - | Input of central locking lock unit, rear right -F223- |
| 19 | - | Input of door contact switch, driver side -F2- (31) |
| 20 | - | Input of door contact switch, front passenger side -F3- (31) |
| 21 | - | Input of central locking lock unit, front passenger side -F221- |
| 22 | - | Input of central locking lock unit, driver side -F220- |
| 23 | - | Input of rear lid remote release button -E233- , rear lid handle release button -E234- (31) (on vehicles without central locking) |
| 24 | - | Input of central locking lock unit, driver side -F220- , central locking lock unit, front passenger side -F221- |
| 25 | - | Input of interior locking switch, driver side -E150- |
| 26 | - | Input of door contact switch, rear right -F11- |
| 27 | - | Input of bonnet contact switch -F266- (31) |
| 28 | - | Input of hazard warning light button -E229- (31) |
| 29 | - | Input of horn activation -H- (31) |
| 30 | - | Input of rear lid lock unit -F256- (31) |
| 31 | - | not assigned |
| 32 | - | Input of turn signal switch -E2- (right turn signal) (31) |
| 33 | - | Input of turn signal switch -E2- (left turn signal) (31) |
| 34 | - | Input of door contact switch, rear left -F10- |
| 35 | - | not assigned |
| 36 | - | not assigned |
| 37 | - | not assigned |
| 38 | - | Output for heated exterior mirror, driver side, heated exterior mirror, front passenger side |
| 39 | - | Input (31) |
| 40 | - | not assigned |
| 41 | - | not assigned |
| 42 | - | Input of ignition starter switch -D- (86s) |
| 43 | - | Input of brake light switch -F- (54) |
| 44 | - | Input of ignition starter switch -D- (15) |
| 45 | - | Input of light switch -E1- (58R) |
| 46 | - | not assigned |
| 47 | - | not assigned |
| 48 | - | not assigned |
| 49 | - | not assigned |
| 50 | - | not assigned |
| 51 | - | not assigned |
| 52 | - | Output for fuel supply relay -J643- (31) |
| 53 | - | not assigned |
| 54 | - | not assigned |
| 55 | - | not assigned |
| 56 | - | Output for hazard warning light system warning light -K6- + bulb for button illumination -L76- |
| 57 | - | not assigned |
| 58 | - | Output for warning light for SAFE function of central locking -K133- |
| 59 | - | Output for interior locking warning light, driver side -K174- |
| 60 | - | Output for heated rear window warning light -K10- |
| 61 | - | not assigned |
| 62 | - | not assigned |
| 63 | - | not assigned |
| 64 | - | Input for heated exterior mirror driver's side -Z4- , heated exterior mirror front passenger's side -Z5- |
| 65 | - | Output for front interior light -W1- , glove box light -W6- (30g) |
| 66 | - | Input for front interior light -W1- , glove box light -W6- (30) |
| 67 | - | not assigned |
| 68 | - | Input for windscreen wiper motor -V- (30) |
| 69 | - | Output for windscreen wiper motor -V- (1st stage) |
| 70 | - | Input (31) |
| 71 | - | Output for windscreen wiper motor -V- (2nd stage) |
| 72 | - | Output for high tone horn -H2- , low tone horn -H7- |
| 73 | - | Input (30) for high tone horn -H2- , low tone horn -H7- |
| 73-pin connector -T73b- (white): |
| 1 | - | not assigned |
| 2 | - | not assigned |
| 3 | - | not assigned |
| 4 | - | not assigned |
| 5 | - | not assigned |
| 6 | - | not assigned |
| 7 | - | not assigned |
| 8 | - | not assigned |
| 9 | - | not assigned |
| 10 | - | not assigned |
| 11 | - | Input for reversing light bulb, left -M16- , reversing light bulb, right -M17- , static cornering light, left -M51- , static cornering light, right -M52- |
| 12 | - | not assigned |
| 13 | - | Input for turn signal (30) |
| 14 | - | Output for turn signal bulb, front left -M5- , turn signal bulb, rear left -M6- , side turn signal bulb, left -M18- |
| 15 | - | Output for turn signal bulb, front right -M7- , turn signal bulb, rear right -M8- , side turn signal bulb, right -M19- |
| 16 | - | Output for brake light bulb, left -M9- , brake light bulb, right -M10- (54) |
| 17 | - | LIN bus door control unit driver's side -J386- , door control unit front passenger's side -J387- , rear left door control unit -J388- , rear right door control unit -J389- |
| 18 | - | Drive train CAN bus, low |
| 19 | - | Drive train CAN bus, high |
| 20 | - | Convenience CAN bus, high |
| 21 | - | Convenience CAN bus, low |
| 22 | - | Drive train CAN bus low (switched) |
| 23 | - | Drive train CAN bus high (switched) |
| 24 | - | not assigned |
| 25 | - | not assigned |
| 26 | - | not assigned |
| 27 | - | Input of intermittent wiper switch -E22- (1st stage) |
| 28 | - | not assigned |
| 29 | - | not assigned |
| 30 | - | not assigned |
| 31 | - | Input of heated rear window button -E230- (31) |
| 32 | - | Input of windscreen wiper motor -V- |
| 33 | - | not assigned |
| 34 | - | Input of light switch -E1- (58L) |
| 35 | - | not assigned |
| 36 | - | not assigned |
| 37 | - | Diagnosis wire K |
| 38 | - | Input (31) |
| 39 | - | Input (30) |
| 40 | - | not assigned |
| 41 | - | not assigned |
| 42 | - | not assigned |
| 43 | - | not assigned |
| 44 | - | not assigned |
| 45 | - | not assigned |
| 46 | - | not assigned |
| 47 | - | not assigned |
| 48 | - | Input of reversing light switch -F4- (not valid for vehicles with automatic gearbox) |
| 49 | - | Input of alternator with voltage regulator -CX1- terminal L |
| 50 | - | Input of ignition starter switch -D- (50) |
| 51 | - | Input of ignition starter switch -D- (75) |
| 52 | - | Input of light switch -E1- (for headlight washer system) |
| 53 | - | Input of intermittent wiper switch -E22- (2nd stage) |
| 54 | - | not assigned |
| 55 | - | not assigned |
| 56 | - | not assigned |
| 57 | - | not assigned |
| 58 | - | Input of exterior mirror heating button |
| 59 | - | Input of fuse in fuse holder A on the battery (30 analogue) |
| 60 | - | Input (31 analog) |
| 61 | - | Input of rear wiper switch -E34- |
| - | Output for rear window wiper motor -V12- | |
| 62 | - | Input of intermittent wiper control -E38- |
| 63 | - | Output for heated rear window -Z1- |
| 64 | - | not assigned |
| 65 | - | not assigned |
| 66 | - | not assigned |
| 67 | - | Input for heated rear window -Z1- (30) |
| 68 | - | not assigned |
| 69 | - | not assigned |
| 70 | - | not assigned |
| 71 | - | not assigned |
| 72 | - | not assigned |
| 73 | - | not assigned |
|
| 52-pin + 28-pin assignment: |
| A | - | Engine control unit -J623- |
| B | - | 28-pin connector, at wiring harness - T28c |
| C | - | 52-pin connector, at wiring harness - T52a |
| 94-pin + 60-pin assignment: |
| A | - | Engine control unit -J623- |
| B | - | 94-pin connector, at wiring harness - T94a |
| C | - | 60-pin connector, at wiring harness - T60a |
|
| Power output module for left headlight -J667- |
| Pin assignment: |
| A | - | Power output module for left headlight -J667- |
| B | - | 10-pin connector, at wiring harness - T10a |
|
| Pin assignment: |
| A | - | Radiator fan control unit -J293- |
| B | - | 10-pin connector, at wiring harness - T10g |
|
Note
|
|
| A | - | 4-pin connector, at wiring harness - T4k |
Note
|
|
| |
| A | - | 4-pin connector, at wiring harness - T4j |
| B | - | 6-pin connector, at wiring harness - T6aj |
| Power output module for right headlight -J668- |
| Pin assignment: |
| A | - | Power output module for right headlight -J668- |
| B | - | 10-pin connector, at wiring harness - T10b |
|
|
| 1 | - | Terminal 30 |
| 2 | - | not assigned |
| 3 | - | not assigned |
| 4 | - | not assigned |
| 5 | - | not assigned |
| 6 | - | Front right speed sensor -G45- |
| 7 | - | Terminal 30 |
| 8 | - | not assigned |
| 9 | - | not assigned |
| 10 | - | not assigned |
| 11 | - | not assigned |
| 12 | - | not assigned |
| 13 | - | Earth |
| 14 | - | Drive train CAN bus, low |
| 15 | - | not assigned |
| 16 | - | not assigned |
| 17 | - | not assigned |
| 18 | - | Front right speed sensor -G45- |
| 19 | - | Rear right speed sensor -G44- |
| 20 | - | Rear left speed sensor -G46- |
| 21 | - | not assigned |
| 22 | - | Front left speed sensor -G47- |
| 23 | - | not assigned |
| 24 | - | not assigned |
| 25 | - | Terminal 30 |
| 26 | - | Drive train CAN bus, high |
| 27 | - | not assigned |
| 28 | - | not assigned |
| 29 | - | not assigned |
| 30 | - | Brake light switch -F- |
| 31 | - | Rear right speed sensor -G44- |
| 32 | - | not assigned |
| 33 | - | Rear left speed sensor -G46- |
| 34 | - | Front left speed sensor -G47- |
| 35 | - | Terminal 15 |
| 36 | - | not assigned |
| 37 | - | not assigned |
| 38 | - | Earth |
|
| Pin assignment: |
| A | - | Airbag control unit -J234- |
| B | - | 50-pin connector, at wiring harness - T50a |
| Pin assignment: Air conditioning system control unit -J301- |
| Pin assignment: |
| A | - | Air conditioning system control unit -J301- |
| B | - | 18-pin connector, at wiring harness - T18c |
| C | - | 16-pin connector, at wiring harness - T16e |
| D | - | 5-pin connector, at wiring harness - T5h |
