Wiring Diagram AUDI A4 2010 - Entry and start authorisation switch - Fuse 6 on fuse holder D
| E415 | Entry and start authorisation switch |
| ST2 | Fuse carrier 2 |
| SD6 | Fuse 6 on fuse holder D |
| T16g | 16-pin connector |
| T17g | 17-pin connector, in right A-pillar coupling station |
| 135 | Earth connection 2, in dash panel wiring harness |
| A209 | Connection 1 (LIN bus) in dash panel wiring harness |
| * | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Control unit in dash panel insert - Radio controlled clock receiver
| J285 | Control unit in dash panel insert |
| J489 | Radio controlled clock receiver |
| J533 | Data bus diagnostic interface |
| ST2 | Fuse carrier 2 |
| SD4 | Fuse 4 on fuse holder D |
| SD5 | Fuse 5 on fuse holder D |
| T3i | 3-pin connector |
| T17c | 17-pin connector, in left A-pillar coupling station |
| T20d | 20-pin connector |
| T32f | 32-pin connector |
| T46s | 46-pin connector |
| 135 | Earth connection 2, in dash panel wiring harness |
| A1 | Positive connection (30a), in dash panel wiring harness |
| * | Up to April 2009 |
| *2 | see applicable current flow diagram for fuse assignment |
| *3 | see applicable current flow diagram |
| *4 | From May 2009 |
Wiring Diagram AUDI A4 2010 - Fuel gauge sender - Fuel system pressurisation pump - Control unit in dash panel insert
| G | Fuel gauge sender |
| G5 | Rev. counter |
| G6 | Fuel system pressurisation pump |
| G21 | Speedometer |
| G169 | Fuel gauge sender 2 |
| J285 | Control unit in dash panel insert |
| T2af | 2-pin connector |
| T5e | 5-pin connector |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T17g | 17-pin connector, in right A-pillar coupling station |
| T32f | 32-pin connector |
| 135 | Earth connection 2, in dash panel wiring harness |
| * | According to equipment |
| *2 | see applicable current flow diagram for engine |
Wiring Diagram AUDI A4 2010 - Steering column electronics control unit
| J527 | Steering column electronics control unit |
| ST1 | Fuse carrier 1 |
| ST2 | Fuse carrier 2 |
| SD5 | Fuse 5 on fuse holder D |
| SD12 | Fuse 12 on fuse holder D |
| T16f | 16-pin connector |
| T17b | 17-pin connector, in left A-pillar coupling station |
| T17q | 17-pin connector, in E-box |
| T46s | 46-pin connector |
| 135 | Earth connection 2, in dash panel wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | see applicable current flow diagram for engine |
| *3 | Front passenger side push-in bridge, brown |
| *4 | Data bus wire (CAN bus) |
Wiring Diagram AUDI A4 2010 - Turn signal switch - Cruise control system switch - Steering column electronics control unit
| E2 | Turn signal switch |
| E45 | Cruise control system switch |
| F138 | Airbag coil connector and return ring with slip ring |
| G85 | Steering angle sender |
| H | Horn plate |
| J234 | Airbag control unit |
| J453 | Multifunction steering wheel control unit |
| J527 | Steering column electronics control unit |
| N95 | Driver side airbag igniter |
| T4ac | 4-pin connector |
| T5b | 5-pin connector |
| T17x | 17-pin connector |
| T100 | 100-pin connector |
| 135 | Earth connection 2, in dash panel wiring harness |
| * | see applicable current flow diagram for multifunction steering wheel |
| *2 | Up to April 2009 |
| *3 | From May 2009 |
| *4 | see applicable current flow diagram for airbag |
Wiring Diagram AUDI A4 2010 - Intermittent wiper switch - Start/Stop operation button - Steering column electronics control unit - Control unit for electronic steering column lock
| E22 | Intermittent wiper switch |
| E693 | Start/Stop operation button |
| J519 | Onboard supply control unit |
| J527 | Steering column electronics control unit |
| J764 | Control unit for electronic steering column lock |
| ST2 | Fuse carrier 2 |
| SD9 | Fuse 9 on fuse holder D |
| T6z | 6-pin connector |
| T12ab | 12-pin connector |
| T17b | 17-pin connector, in left A-pillar coupling station |
| T17e | 17-pin connector, in left A-pillar coupling station |
| T17g | 17-pin connector, in right A-pillar coupling station |
| T32a | 32-pin connector |
| 135 | Earth connection 2, in dash panel wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | Only models with stop/start system |
Wiring Diagram AUDI A4 2010 - Bonnet contact switch - Treble horn - Bass horn - Horn relay
| F266 | Bonnet contact switch |
| H2 | Treble horn |
| H7 | Bass horn |
| J413 | Horn relay |
| J519 | Onboard supply control unit |
| ST2 | Fuse carrier 2 |
| ST3 | Fuse carrier 3 |
| SC6 | Fuse 6 on fuse holder C |
| SC7 | Fuse 7 on fuse holder C |
| T2s | 2-pin connector |
| T17l | 17-pin connector |
| T17q | 17-pin connector, in E-box |
| T17r | 17-pin connector, in E-box |
| T32b | 32-pin connector |
| 366 | Earth connection 1, in main wiring harness |
| 368 | Earth connection 3, in main wiring harness |
| B474 | Connection 10, in main wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | see applicable current flow diagram for engine |
Wiring Diagram AUDI A4 2010 - Rain and light sensor - Wiper motor control unit
| G397 | Rain and light sensor |
| J400 | Wiper motor control unit |
| J519 | Onboard supply control unit |
| ST1 | Fuse carrier 1 |
| ST2 | Fuse carrier 2 |
| SC8 | Fuse 8 on fuse holder C |
| SC9 | Fuse 9 on fuse holder C |
| SC12 | Fuse 12 on fuse holder C |
| T3c | 3-pin connector |
| T4g | 4-pin connector |
| T16b | 16-pin connector |
| T17m | 17-pin connector |
| T17n | 17-pin connector |
| T32b | 32-pin connector |
| T46i | 46-pin connector |
| 370 | Earth connection 5, in main wiring harness |
| B475 | Connection 11, in main wiring harness |
| * | Only right-hand drive models |
| *2 | see applicable current flow diagram for fuse assignment |
| *3 | Left-hand drive models |
| *4 | Driver side push-in bridge, brown |
| *5 | Up to April 2009 |
| *6 | Data bus wire (CAN bus) |
| *7 | From May 2009 |
Wiring Diagram AUDI A4 2010 - Gear detector switch - Front left brake pad wear sender - Headlight washer system pump - Left washer jet heater element - Right washer jet heater element
| F208 | Gear detector switch |
| G34 | Front left brake pad wear sender |
| J519 | Onboard supply control unit |
| ST1 | Fuse carrier 1 |
| SC11 | Fuse 11 on fuse holder C |
| T2b | 2-pin connector |
| T2i | 2-pin connector |
| T2r | 2-pin connector |
| T2v | 2-pin connector |
| T17l | 17-pin connector |
| T17q | 17-pin connector, in E-box |
| T32b | 32-pin connector |
| V11 | Headlight washer system pump |
| Z20 | Left washer jet heater element |
| Z21 | Right washer jet heater element |
| 370 | Earth connection 5, in main wiring harness |
| * | Only models with heater elements for washer jets |
| *2 | Only models with headlight washer system |
| *3 | see applicable current flow diagram for engine |
| *4 | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Brake fluid level warning contact - Ambient temperature sensor - Coolant shortage indicator sender - Windscreen washer fluid level sender - Rear window wiper motor
| F34 | Brake fluid level warning contact |
| G17 | Ambient temperature sensor |
| G32 | Coolant shortage indicator sender |
| G33 | Windscreen washer fluid level sender |
| J519 | Onboard supply control unit |
| T2a | 2-pin connector |
| T2aa | 2-pin connector |
| T2t | 2-pin connector |
| T2u | 2-pin connector |
| T17l | 17-pin connector |
| T32b | 32-pin connector |
| V5 | Washer pump |
| V12 | Rear window wiper motor |
| 401 | Earth connection (sender earth), in interior wiring harness |
| B536 | Connection 27, in main wiring harness |
| B538 | Connection 29, in main wiring harness |
| * | Avant |
| *2 | Saloon |
Wiring Diagram AUDI A4 2010 - Switch module for driving mode selection
| E592 | Switch module for driving mode selection |
| E593 | Button 1 in switch module for driving mode selection |
| E594 | Button 2 in switch module for driving mode selection |
| J519 | Onboard supply control unit |
| SD2 | Fuse 2 on fuse holder D |
| ST2 | Fuse carrier 2 |
| T3m | 3-pin connector |
| T16b | 16-pin connector |
| T17d | 17-pin connector, in left A-pillar coupling station |
| T17f | 17-pin connector, in right A-pillar coupling station |
| B549 | Connection 2 (LIN bus) in main wiring harness |
| * | Only models with no navigation system |
| *2 | Only models with navigation system |
| *3 | see applicable current flow diagram for fuse assignment |
| *4 | gradual introduction |
| *5 | Gradually discontinued |
Wiring Diagram AUDI A4 2010 - Light switch - Hazard warning lights button
| E1 | Light switch |
| E20 | Switch and instrument illumination regulator |
| E229 | Hazard warning lights button |
| E314 | Rear fog light button |
| E315 | Fog light button |
| J234 | Airbag control unit |
| J519 | Onboard supply control unit |
| K6 | Indicator lamp for hazard warning light |
| K145 | Front passenger side airbag deactivated warning lamp |
| ST1 | Fuse carrier 1 |
| ST2 | Fuse carrier 2 |
| SD4 | Fuse 4 on fuse holder D |
| ST4 | Fuse carrier 4 |
| SD7 | Fuse 7 on fuse holder D |
| SF12 | Fuse 12 in fuse holder F |
| SC14 | Fuse 14 on fuse holder C |
| T4t | 4-pin connector |
| T6ae | 6-pin connector |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T32a | 32-pin connector |
| T100 | 100-pin connector |
| 81 | Earth connection 1, in dash panel wiring harness |
| B163 | Positive connection 1 (15), in interior wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | Up to April 2009 |
| *3 | From May 2009 |
| *4 | see applicable current flow diagram for airbag |
Wiring Diagram AUDI A4 2010 - Front left headlight
| E102 | Headlight range control regulator |
| J519 | Onboard supply control unit |
| L22 | Left fog light bulb |
| L174 | Left daytime running light bulb |
| M1 | Left side light bulb |
| MX1 | Front left headlight |
| M5 | Front left turn signal bulb |
| M29 | Left headlight dipped beam bulb |
| M30 | Left headlight main beam bulb |
| M33 | Front left side marker bulb |
| ST3 | Fuse carrier 3 |
| SC8 | Fuse 8 on fuse holder C |
| T10a | 10-pin connector |
| T17b | 17-pin connector, in left A-pillar coupling station |
| T17g | 17-pin connector, in right A-pillar coupling station |
| T17m | 17-pin connector |
| T17n | 17-pin connector |
| V48 | Left headlight range control motor |
| B165 | Positive connection 2 (15), in interior wiring harness |
| B488 | Connection 24, in main wiring harness |
| C69 | Front left connection (fog light),, in main wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | Only models with no US equipment |
| *3 | Only models with US equipment |
| *4 | Only models with daytime running lights |
Wiring Diagram AUDI A4 2010 - Front right headlight
| J519 | Onboard supply control unit |
| L23 | Right fog light bulb |
| L175 | Right daytime running light bulb |
| MX2 | Front right headlight |
| M3 | Right side light bulb |
| M7 | Front right turn signal bulb |
| M31 | Right headlight dipped beam bulb |
| M32 | Right headlight main beam bulb |
| M34 | Front right side marker bulb |
| ST1 | Fuse carrier 1 |
| ST3 | Fuse carrier 3 |
| SC6 | Fuse 6 on fuse holder C |
| SC10 | Fuse 10 on fuse holder C |
| T10b | 10-pin connector |
| T17m | 17-pin connector |
| T17n | 17-pin connector |
| V49 | Right headlight range control motor |
| B165 | Positive connection 2 (15), in interior wiring harness |
| B488 | Connection 24, in main wiring harness |
| C15 | Connection 1, in headlight wiring harness |
| C25 | Connection (fog light), in front lighting wiring harness |
| * | Only models with no US equipment |
| *2 | see applicable current flow diagram for fuse assignment |
| *3 | Only models with daytime running lights |
| *4 | Only models with US equipment |
| *5 | Only for American markets |
Wiring Diagram AUDI A4 2010 - Rear left reading light button - Vanity mirror light bulb - Front interior light - Rear right interior light
| E317 | Interior light switch |
| E454 | Rear left reading light button |
| E455 | Rear right reading light button |
| E457 | Driver side reading light button |
| E458 | Front passenger side reading light button |
| F147 | Driver vanity mirror contact switch |
| F148 | Front passenger vanity mirror contact switch |
| J519 | Onboard supply control unit |
| L31 | Vanity mirror light bulb |
| T8b | 8-pin connector |
| T17l | 17-pin connector |
| W1 | Front interior light |
| W13 | Front passenger reading light |
| W19 | Driver side reading light |
| W47 | Rear left interior light |
| W48 | Rear right interior light |
| Y7 | Automatic anti-dazzle interior mirror |
| B476 | Connection 12, in main wiring harness |
| * | According to equipment |
Wiring Diagram AUDI A4 2010 - Key operated switch to deactivate front passenger side airbag - Valet parking button - Valet parking warning lamp
| E224 | Key operated switch to deactivate front passenger side airbag |
| E536 | Valet parking button |
| J234 | Airbag control unit |
| J519 | Onboard supply control unit |
| K159 | Valet parking warning lamp |
| L67 | Dash panel left vent illumination bulb |
| L68 | Dash panel central vent illumination |
| L69 | Dash panel right vent illumination bulb |
| T12k | 12-pin connector |
| T17g | 17-pin connector, in right A-pillar coupling station |
| T32a | 32-pin connector |
| T100 | 100-pin connector |
| 378 | Earth connection 13, in main wiring harness |
| 475 | Earth connection (airbag), in main wiring harness |
| B478 | Connection 14, in main wiring harness |
| * | Only models with key operated switch to deactivate front passenger airbag |
| *2 | see applicable current flow diagram for airbag |
| *3 | According to equipment |
Wiring Diagram AUDI A4 2010 - Glove compartment light switch - Front left footwell illumination bulb - Front right footwell illumination bulb - Glove compartment light
| E26 | Glove compartment light switch |
| J519 | Onboard supply control unit |
| L151 | Front left footwell illumination bulb |
| L152 | Front right footwell illumination bulb |
| T10m | 10-pin connector, Coupling point under front passenger seat |
| T10p | 10-pin connector, near driver seat |
| T12k | 12-pin connector |
| T17d | 17-pin connector, brown |
| T17g | 17-pin connector, black |
| T17l | 17-pin connector |
| T32a | 32-pin connector |
| W6 | Glove compartment light |
| W45 | Rear left footwell light |
| W46 | Rear right footwell light |
| 369 | Earth connection 4, in main wiring harness |
| 378 | Earth connection 13, in main wiring harness |
| B433 | Connection (footwell light), in main wiring harness |
| B479 | Connection 15, in main wiring harness |
| * | Gradually discontinued |
| *2 | According to equipment |
| *3 | gradual introduction |
Wiring Diagram AUDI A4 2010 - 12 V socket
| E538 | Electromechanical parking brake button |
| G538 | Potentiometer for rear temperature selection |
| J519 | Onboard supply control unit |
| L42 | Socket illumination bulb |
| SF2 | Fuse 2 in fuse holder F |
| ST4 | Fuse carrier 4 |
| T3l | 3-pin connector |
| T3p | 3-pin connector |
| T8ad | 8-pin connector |
| T12b | 12-pin connector |
| T32b | 32-pin connector |
| U5 | 12 V socket, in front centre console |
| U13 | DC/AC converter with socket, 12 V - 230 V |
| 369 | Earth connection 4, in main wiring harness |
| B490 | Connection 26, in main wiring harness |
| * | see applicable current flow diagram for air conditioning |
| *2 | According to equipment |
| *3 | see applicable current flow diagram for fuse assignment |
| *4 | Only models with DC/AC converter |
Wiring Diagram AUDI A4 2010 - Adaptive cruise control unit
| J428 | Adaptive cruise control unit |
| J519 | Onboard supply control unit |
| J533 | Data bus diagnostic interface |
| J769 | Lane change assist control unit |
| ST1 | Fuse carrier 1 |
| ST4 | Fuse carrier 4 |
| SF7 | Fuse 7 in fuse holder F |
| SC9 | Fuse 9 on fuse holder C |
| T8a | 8-pin connector |
| T12f | 12-pin connector |
| T12h | 12-pin connector |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T20d | 20-pin connector |
| B108 | Connection 1 (CAN bus extended high), in main wiring harness |
| B109 | Connection 1 (CAN bus extended low), in main wiring harness |
| B665 | Connection 1 (CAN bus extended high), in dash panel wiring harness |
| B666 | Connection 1 (CAN bus extended low), in dash panel wiring harness |
| * | Only models with adaptive cruise control (ACC) |
| *2 | From May 2009 |
| *3 | Up to April 2009 |
| *4 | Only models with lane departure warning assist |
| *5 | Data bus wire (CAN bus) |
Wiring Diagram AUDI A4 2010 - Rear roller blind switch - TCS and ESP button - Parking aid button
| E149 | Rear roller blind switch |
| E256 | TCS and ESP button |
| E266 | Parking aid button |
| J104 | ABS control unit |
| J519 | Onboard supply control unit |
| J791 | Park assist steering control unit |
| ST1 | Fuse carrier 1 |
| SD6 | Fuse 6 on fuse holder D |
| T8r | 8-pin connector |
| T16e | 16-pin connector |
| T17c | 17-pin connector, in left A-pillar coupling station |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T17g | 17-pin connector, in right A-pillar coupling station |
| T32a | 32-pin connector |
| T38a | 38-pin connector |
| * | Only models with navigation system |
| *2 | Only models with no navigation system |
| *3 | Only models with parking aid (PDC) |
| *4 | see applicable current flow diagram for ABS |
| *5 | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Entry and start authorisation button
| E408 | Entry and start authorisation button |
| J519 | Onboard supply control unit |
| J587 | Selector lever sensors control unit |
| ST2 | Fuse carrier 2 |
| SC5 | Fuse 5 on fuse holder C |
| T4n | 4-pin connector |
| T6f | 6-pin connector |
| T6k | 6-pin connector, Coupling point under front passenger seat |
| T6l | 6-pin connector, near driver seat |
| T10k | 10-pin connector |
| T32b | 32-pin connector |
| B472 | Connection 8, in main wiring harness |
| * | see applicable current flow diagram for fuse assignment |
| *2 | see applicable current flow diagram for automatic gearbox |
| *3 | see applicable current flow diagram for seat heating |
Wiring Diagram AUDI A4 2010 - Entry and start authorisation button - Contact sensor for front left exterior door handle - Contact sensor for front right exterior door handle - Convenience system central control unit - Left aerial for entry and start authorisation
| E408 | Entry and start authorisation button |
| G605 | Contact sensor for front left exterior door handle |
| G606 | Contact sensor for front right exterior door handle |
| J393 | Convenience system central control unit |
| R137 | Luggage compartment aerial for entry and start system |
| R138 | Interior aerial 1 for entry and start system |
| R200 | Left aerial for entry and start authorisation |
| T2aj | 2-pin connector |
| T2bo | 2-pin connector |
| T2bp | 2-pin connector |
| T2bv | 2-pin connector |
| T2bw | 2-pin connector |
| T4n | 4-pin connector |
| T17p | 17-pin connector |
| T27a | 27-pin connector, in left A-pillar |
| T27b | 27-pin connector, in left A-pillar |
| T27c | 27-pin connector, in right A-pillar |
| T32d | 32-pin connector |
| T32e | 32-pin connector |
| 205 | Earth connection, in driver door wiring harness |
| 206 | Earth connection, in front passenger door wiring harness |
| 367 | Earth connection 2, in main wiring harness |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit - Left tail light - Left tail light 2 - Luggage compartment light
| J393 | Convenience system central control unit |
| MX3 | Left tail light |
| M4 | Left tail light bulb |
| MX5 | Left tail light 2 |
| M6 | Rear left turn signal bulb |
| M16 | Left reversing light bulb |
| M21 | Left brake and tail light bulb |
| M37 | Rear left side marker bulb |
| M41 | Left tail light and rear fog light bulb |
| M69 | Left brake, turn signal and tail light bulb |
| T2ah | 2-pin connector |
| T17o | 17-pin connector |
| T17p | 17-pin connector |
| T32c | 32-pin connector |
| W3 | Luggage compartment light |
| 371 | Earth connection 6, in main wiring harness |
| 372 | Earth connection 7, in main wiring harness |
| B477 | Connection 13, in main wiring harness |
| * | Saloon |
| *2 | Only models with US equipment |
| *3 | Only models with no US equipment |
| *4 | Cross-section 1.5 possible |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit - Rear lid central locking motor
| F124 | Contact switch in lock cylinder for rear lid, anti-theft alarm system and central locking system |
| F248 | Release button for rear lid lock cylinder |
| J329 | Terminal 15 voltage supply relay |
| J393 | Convenience system central control unit |
| M25 | High-level brake light bulb |
| ST2 | Fuse carrier 2 |
| SF8 | Fuse 8 in fuse holder F |
| SF10 | Fuse 10 in fuse holder F |
| SF11 | Fuse 11 in fuse holder F |
| T2g | 2-pin connector |
| T17o | 17-pin connector |
| T17p | 17-pin connector |
| T32c | 32-pin connector |
| T32d | 32-pin connector |
| V53 | Rear lid central locking motor |
| X4 | Left number plate light |
| X5 | Right number plate light |
| 249 | Earth connection 2, in interior wiring harness |
| 372 | Earth connection 7, in main wiring harness |
| 690 | Earth point, rear centre roof frame |
| * | Saloon |
| *2 | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit - Right tail light - Right tail light 2
| J393 | Convenience system central control unit |
| M2 | Right tail light bulb |
| MX4 | Right tail light |
| MX6 | Right tail light 2 |
| M8 | Rear right turn signal bulb |
| M17 | Right reversing light bulb |
| M22 | Right brake and tail light bulb |
| M38 | Rear right side marker bulb |
| M42 | Right tail light and rear fog light bulb |
| M70 | Right brake, turn signal and tail light bulb |
| T17o | 17-pin connector |
| T17p | 17-pin connector |
| T32c | 32-pin connector |
| 372 | Earth connection 7, in main wiring harness |
| * | Saloon |
| *2 | Only models with US equipment |
| *3 | Only models with no US equipment |
Wiring Diagram AUDI A4 2010 - Sliding sunroof adjustment regulator - Sliding sunroof adjustment control unit - Convenience system central control unit - Sliding sunroof motor
| E139 | Sliding sunroof adjustment regulator |
| J245 | Sliding sunroof adjustment control unit |
| J393 | Convenience system central control unit |
| ST3 | Fuse carrier 3 |
| SC9 | Fuse 9 on fuse holder C |
| SC11 | Fuse 11 on fuse holder C |
| T6e | 6-pin connector, black |
| T10c | 10-pin connector |
| T10x | 10-pin connector |
| T32c | 32-pin connector |
| V1 | Sliding sunroof motor |
| 277 | Earth connection 3, in interior wiring harness |
| B528 | Connection 1 (LIN bus) in main wiring harness |
| * | Avant |
| *2 | see applicable current flow diagram |
| *3 | Saloon |
| *4 | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Anti-theft alarm sensor - Alarm horn - Convenience system central control unit - Central locking and anti-theft alarm system aerial - Aerial amplifier 3
| G578 | Anti-theft alarm sensor |
| H12 | Alarm horn |
| J393 | Convenience system central control unit |
| R47 | Central locking and anti-theft alarm system aerial |
| R112 | Aerial amplifier 3 |
| ST3 | Fuse carrier 3 |
| SC12 | Fuse 12 on fuse holder C |
| T3e | 3-pin connector |
| T4f | 4-pin connector |
| T32c | 32-pin connector |
| 277 | Earth connection 3, in interior wiring harness |
| 377 | Earth connection 12, in main wiring harness |
| B301 | Positive connection 5 (30), in main wiring harness |
| B528 | Connection 1 (LIN bus) in main wiring harness |
| * | Saloon |
| *2 | see applicable current flow diagram for fuse assignment |
| *3 | see applicable current flow diagram for MMI (information electronics) |
| *4 | According to equipment |
Wiring Diagram AUDI A4 2010 - Clutch pedal switch - Convenience system central control unit
| F36 | Clutch pedal switch |
| F194 | Clutch pedal switch for engine start |
| F305 | Gear selector position P switch |
| G476 | Clutch position sender |
| J217 | Automatic gearbox control unit |
| J393 | Convenience system central control unit |
| J623 | Engine control unit |
| T4h | 4-pin connector |
| T6g | 6-pin connector |
| T17q | 17-pin connector, in E-box |
| T17r | 17-pin connector, in E-box |
| T32d | 32-pin connector |
| B471 | Connection 7, in main wiring harness |
| D114 | Connection 12 in engine compartment wiring harness |
| * | see applicable current flow diagram for engine |
| *2 | Only models with manual gearbox |
| *3 | see applicable current flow diagram for automatic gearbox |
Wiring Diagram AUDI A4 2010 - Brake light switch - Convenience system central control unit
| F | Brake light switch |
| J255 | Climatronic control unit |
| J393 | Convenience system central control unit |
| J623 | Engine control unit |
| T4k | 4-pin connector |
| T12u | 12-pin connector, brown |
| T17e | 17-pin connector, in left A-pillar coupling station |
| T17r | 17-pin connector, in E-box |
| T20e | 20-pin connector |
| T32d | 32-pin connector |
| B146 | Positive connection 1 (87), in interior wiring harness |
| B335 | Connection 1 (54), in main wiring harness |
| * | see applicable current flow diagram for engine |
| *2 | Solenoid coil for brake light sensor |
| *3 | see applicable current flow diagram for air conditioning |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit
| J345 | Trailer detector control unit |
| J387 | Front passenger door control unit |
| J393 | Convenience system central control unit |
| J502 | Tyre Pressure Monitoring System control unit |
| J605 | Rear lid control unit |
| J772 | Reversing camera system control unit |
| T8ae | 8-pin connector |
| T12d | 12-pin connector |
| T12u | 12-pin connector, brown |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T20a | 20-pin connector |
| T20g | 20-pin connector |
| T27c | 27-pin connector, in right A-pillar |
| T32c | 32-pin connector |
| T46s | 46-pin connector |
| T54b | 54-pin connector |
| B398 | Connection 2 (convenience CAN bus, high), in main wiring harness |
| B401 | Connection 5 (convenience CAN bus, high), in main wiring harness |
| * | Only models with reversing camera system |
| *2 | Only models with trailer socket |
| *3 | Avant |
| *4 | Only models with Tyre Pressure Monitoring System |
| *5 | see applicable current flow diagram for convenience system |
| *6 | Front passenger side push-in bridge, brown |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit
| J345 | Trailer detector control unit |
| J387 | Front passenger door control unit |
| J393 | Convenience system central control unit |
| J502 | Tyre Pressure Monitoring System control unit |
| J605 | Rear lid control unit |
| J772 | Reversing camera system control unit |
| T8ae | 8-pin connector |
| T12d | 12-pin connector |
| T12u | 12-pin connector, brown |
| T17f | 17-pin connector, in right A-pillar coupling station |
| T20a | 20-pin connector |
| T20g | 20-pin connector |
| T27c | 27-pin connector, in right A-pillar |
| T32c | 32-pin connector |
| T46s | 46-pin connector |
| T54b | 54-pin connector |
| B407 | Connection 2 (convenience CAN bus, low), in main wiring harness |
| B410 | Connection 5 (convenience CAN bus, low), in main wiring harness |
| * | see applicable current flow diagram for convenience system |
| *2 | Front passenger side push-in bridge, brown |
| *3 | Only models with Tyre Pressure Monitoring System |
| *4 | Only models with reversing camera system |
| *5 | Only models with trailer socket |
| *6 | Avant |
Wiring Diagram AUDI A4 2010 - Convenience system central control unit - Rear roller blind motor - Tank filler flap locking motor - Heated rear window
| C18 | Window aerial suppression filter |
| J9 | Heated rear window relay |
| J393 | Convenience system central control unit |
| J807 | Relay for power sockets |
| R178 | Frequency modulation (FM) frequency filter in negative wire |
| R179 | Frequency modulation (FM) frequency filter in positive wire |
| S41 | Heated rear window single fuse |
| T2k | 2-pin connector |
| T17o | 17-pin connector |
| T17p | 17-pin connector |
| T32c | 32-pin connector |
| T32d | 32-pin connector |
| V91 | Rear roller blind motor |
| V155 | Tank filler flap locking motor |
| Z1 | Heated rear window |
| 657 | Earth point 1, on left near rear window |
| * | Saloon |
| *2 | Only vehicles with electric rear roller blind |
| *3 | see applicable current flow diagram for fuse assignment |
Wiring Diagram AUDI A4 2010 - Cigarette lighter - 12 V socket 2 - 12 V socket 3
| R126 | Telephone bracket |
| SF1 | Fuse 1 in fuse holder F |
| SF3 | Fuse 3 in fuse holder F |
| ST4 | Fuse carrier 4 |
| SF4 | Fuse 4 in fuse holder F |
| T3g | 3-pin connector |
| T3n | 3-pin connector |
| U1 | Cigarette lighter |
| U18 | 12 V socket 2 |
| U19 | 12 V socket 3 |
| B473 | Connection 9, in main wiring harness |
| * | According to equipment |
| *2 | Only models with 12 V socket in luggage compartment |
| *3 | see applicable current flow diagram for telephone systems |
| *4 | see applicable current flow diagram for seat heating |
| *5 | see applicable current flow diagram for fuse assignment |
AUDI A4 2010 Overview of fuses
Note
| Overview also valid for Avant models (5-door)! |
| Fuse holder A -SA- |
| q | Fitting location: |
| 1 - | Battery isolation relay fuse -S171- |
| q | Fitting location next to second battery |
| q | Fitting location for models with right-hand drive, up to and including model year 2009: |
| q | Fitting location for models with left-hand drive, from model year 2010: |
| q | Fitting location for models with right-hand drive, from model year 2010: |
| q | Fitting location for models with left-hand drive, from November 2011: |
| q | Fitting location for models with right-hand drive, from November 2011: |
| q | Fitting location for models with right-hand drive: |
| 6-pin coupling station of A-pillar, driver side |
| q | Fitting location for models with left-hand drive: |
| q | Fitting location for models with right-hand drive: |
| 3-pin relay and fuse holder |
| q | Fitting location for models with left-hand drive: |
| q | Fitting location for models with right-hand drive: |
| Relay/fuse holder B -SB- |
| q | Fitting location for models with left-hand drive, up to October 2011: |
| q | Fitting location for models with right-hand drive, up to October 2011: |
| q | Fitting location for models with left-hand drive, from November 2011: |
| q | Fitting location for models with right-hand drive, from November 2011: |
| Terminal 30 wiring junction 2 -TV22- with jump start socket -U6- |
| q | Fitting location up to October 2011: |
| q | Fitting location from November 2011: |
| 6-pin coupling station of A-pillar, front passenger side |
| q | Fitting location for models with left-hand drive: |
| q | Fitting location for models with right-hand drive: |
| q | Fitting location for models with right-hand drive: |
| Relay/fuse holder F -SF- |
| q | Fitting location up to and including model year 2009: |
| q | Fitting location from model year 2010: |
| q | Fitting location from November 2011: |
|
| A - | Battery isolation igniter -N253- |
| 1 - | Fuse 1 on fuse holder A -SA1-, |
| 2 - | Fuse 2 on fuse holder A -SA2-, |
| 3 - | Fuse 3 on fuse holder A -SA3-, |
| ST1 - | Fuse carrier 1, fuses |
| ST2 - | Fuse carrier 2, fuses |
| A - | 46-pin connector, black, CAN disconnector, dash panel -T46s- |
|
| ST1 - | Fuse carrier 1, fuses |
| ST2 - | Fuse carrier 2, fuses |
| A - | 46-pin connector, black, CAN disconnector, dash panel -T46s- |
|
| No. | Current Flow Diagram designation | Nominal value | Function/component | Terminal | ||
| 1 | - | Fuse 1 on fuse holder D -SD1- | - | Not assigned | ||
| 2 | - | Fuse 2 on fuse holder D -SD2- | - | Not assigned | ||
| 3 | - | Fuse 3 on fuse holder D -SD3- | - | Not assigned | ||
| 4 | - | Fuse 4 on fuse holder D -SD4- | - | Not assigned | ||
| 5 | - | Fuse 5 on fuse holder D -SD5- | 5 A | - | Steering column electronics control unit -J527- | 15 |
| 6 | - | Fuse 6 on fuse holder D -SD6- | 5 A | - | TCS and ESP button -E256- Parking aid button -E266- | 15 |
| 7 | - | Fuse 7 on fuse holder D -SD7- | 5 A | - | 16-pin connector -T16-, diagnostic connector | 15 |
| 8 | - | Fuse 8 on fuse holder D -SD8- | 5 A | - | Data bus diagnostic interface -J533- | 15 |
| 9 | - | Fuse 9 on fuse holder D -SD9- | 5 A | - | High heat output relay -J360- | 15 |
| 10 | - | Fuse 10 on fuse holder D -SD10- | - | Not assigned | ||
| 11 | - | Fuse 11 on fuse holder D -SD11- | - | Not assigned | ||
| 12 | - | Fuse 12 on fuse holder D -SD12- | - | Not assigned |
|
| No. | Current Flow Diagram designation | Nominal value | Function/component | Terminal | ||
| 1 | - | Fuse 1 on fuse holder D -SD1- | 5 A | - | CD changer -R41- DVD changer -R161- Connection for external audio sources -R199- | 30 |
| 2 | - | Fuse 2 on fuse holder D -SD2- | 5 A | - | Switch module for driving mode selection -E592- | 30 |
| 3 | - | Fuse 3 on fuse holder D -SD3- | 5 A 5 A 20 A 20 A | - | Display unit for front information display and operating unit control unit -J685- Control unit 1 for information electronics -J794- Radio -R- | 30 |
| 4 | - | Fuse 4 on fuse holder D -SD4- | 5 A | - | Control unit in dash panel insert -J285- | 30 |
| 5 | - | Fuse 5 on fuse holder D -SD5- | 5 A | - | Data bus diagnostic interface -J533- | 30 |
| 6 | - | Fuse 6 on fuse holder D -SD6- | 5 A | - | Entry and start authorisation switch -E415- | 30 |
| 7 | - | Fuse 7 on fuse holder D -SD7- | 5A | - | Light switch -E1- | |
| 8 | - | Fuse 8 on fuse holder D -SD8- | 40 A | - | Fresh air blower control unit -J126- | 30 |
| 9 | - | Fuse 9 on fuse holder D -SD9- | 5 A | - | Control unit for electronic steering column lock -J764- | 30 |
| 10 | - | Fuse 10 on fuse holder D -SD10- | 10 A | - | Climatronic control unit -J255- | 30 |
| 11 | - | Fuse 11 on fuse holder D -SD11- | 10 A | - | 16-pin connector -T16-, diagnostic connector | 30 |
| 12 | - | Fuse 12 on fuse holder D -SD12- | 5 A | - | Steering column electronics control unit -J527- | 30 |
|
| ST1 - | Fuse carrier 1, fuses |
| ST2 - | Fuse carrier 2, fuses |
| ST3 - | Fuse carrier 3, fuses |
| ST4 - | Fuse carrier 4, fuses |
| ST5 - | Fuse carrier 5, fuses |
| H - | Heated rear window single fuse -S41- |
|


































































































































