DescriptionA control system called SELESPEED supervisesand governs the operation of the manual gearbox via an electrohydraulicdevice.An electronic control unit manages a complexoperating logic which enables the gearbox to be used in both 'semi-automatic'conditions, in which the driver manages the engagement of the gearsusing the lever or the two steering wheel buttons, and automatic'CITY' mode which delegates gear change management to the electronicsystem.The electronic control unit dialogues withthe engine management control unit via two dedicated lines (CAN),and receives the rpm, engine torque and engine temperature signals.The control unit drives, by means of a complexoperating logic, an electrohydraulic unit located on the gearbox,via a specific electric pump. For more details, 3232901Characteristic of working principle2127ELECTRO-HYDRAULIC SELECTION.GEARBOX EXTERNAL. CONTROLS . The system is also controlled by means oftwo relays located in the engine compartment near the battery.The supply lines to the control unit andthe various system components (sensors and actuators) are protectedby two specific maxifuses and other jumper fuses, located next tothe junction unit.
Functional description The SELESPEED control unit M54 monitorsand controls the entire gearbox management system. The control unit is supplied directly bythe battery, via the line of the maxifuse O/A located on the battery(connector B99 D ), at pin 27 of connector A of M54 . The supply controlled by the ignition (15/54)reaches pin 28 of connector A of M54 , via the line protectedby fuse F4 of supplementary fuse box B98 A. Pins 1 and 2 of connector A of M54 areearthed. A set of sensors and potentiometers on thegearbox informs the control unit as to which gear is engaged: the potentiometers are supplied from pin73 of connector B; the gear selection potentiometer K68 returnsa signal to pin 51 of connector A; the gear engagement potentiometer K69 returns a signal to pin 39 of connector A; the hydraulic unitoil pressure sensor K96 returns a signal to pin 40 of connectorA. The clutch position potentiometer K95 issupplied from pin 79 of connector B and returns a signal to pin52 of connector A. Pins 38 and 50 of connector A M54 areconnected to the car speed sensor (gearbox output) K77 . Pin 36 of connector A is connected to instrument E10 from which it receives the speedometer signal (car speed). Pin 48 of connector A is connected to instrument E15 from which it receives the engine rpm signal. The gear control unit H37 is connectedto the control unit M54 to signal the request to engage agear: these signals are sent to pins 67, 74, 68 of connector B of M54 ;and to pin 26 of connector A to signal the request for gears 1,2, 3 and D respectively. The selector H39 allows the CITYmode to be selected; it is connected to the M54 control unitat pin 77 of connector B; (the display is also lit up with the sidelights on (line coming from steering column switch unit H5 ). The steering wheel controls H38 sendsignals to pin 75 of connector B of M54 . Pin 69 of connector B of M10 receivesthe signal coming from the brake lights switch I30 , withthe supply controlled by the ignition (INT) from fuse F1 ofthe junction unit B13233830SeeE2021BRAKE LIGHTS . In accordance with the operating logic,the control unit controls the electrohydraulic unit located on thegearbox which effects the gear change: the electric pump N48 ,which keeps the oil in the hydraulic unit under pressure, is controlledfrom pin 31 of connector A. The pump N48 is controlled by a specificrelay J86 (supplied by the line of the specific maxifuseF/P located on the battery (connector B99 D ). The control unit then controls theopening of the hydraulic unit solenoids:the two gear engagement solenoids L51 and L52 arecontrolled from pins 32 and 44 of connector A of M54 ;the two gear selection solenoids L53 and L54 arecontrolled from pins 29 and 3 of connector A of M54 ;the clutch control solenoid L56 is controlled frompin 43 3 of connector A of M54 . A safety signal comes from pin 42 of connectorA of M54 for the starting enablement relay J05 whichgives starting enablement, pin 50 of the starter motor A20 ;the signal requesting starting reaches pin 76 of connector B 3234399SeeE5010STARTING AND RECHARING . The control unit M54 also managesthe door open buzzer: the driver's door open signal - catch N50 - reaches pin 78 of connector B of M54 ; the control for thebuzzer, located in instrument E15 departs from pin 80 ofconnector B. The control unit M54 has a self-testsystem, which can be used by connecting the unit to the connector R10 :this receives signals from pin 49 of connector A of M54 (theserial line is shared with the engine control unit M10 ). The same self-test also sends signals forthe 'automatic gearbox fault' warning light. located in the instrument E15 , via the same line - coming out of pin 72 of connectorB - it is used for the gear indication display on the instrument itself. The control unit M54 is connectedto the engine management control unit M10 : this connectionis made via the CAN line from pins 33 and 45 of connector B of M54 andis connected to pins 12 and 29 of connector A of M10 .
0Removing201Refitting21Place the car on a ramp.Undo the bolt securing the bracket on thebattery mount.Release the battery from the anchoragebracket complete with strap and remove.
5530B14
769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour:a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery;a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For more details 3238420See subassembly5530 CURRENT GENERATOR . 768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360').Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows: If the voltage without load is less than12.10 V, replace the battery ( 32384295530B10battery - r+r ). If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery ( 32384305530B14battery - recharge ). If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
5530B22
0Removing201Refitting21Place the car on the liftingbridge.1. Open engine compartment cap and disconnect battery negative terminal.2. Disconnect mass terminal on side member.3. Lift the car and disconnect mass terminal on gearbox.4. Lower the car again and remove battery earth lead.2018767
0Removing201Refitting21Disconnect the battery negative terminal.1. Open the protective cover2. Loosen the nut and disconnect the ABS supply lead3. Loosen the nut and disconnect the starter motor supply lead4. Undo the clip and undo the box retaining bolts.5. Loosen the battery positive terminal nut.2018769
5530B52
0Removing201Refitting213238429-5530B10battery - r+rRelease the air duct hose from the mountingbracket on the drip tray. Remove the relay shield.1. Release the relays from the battery drip tray and remove them.2. Undo the nut fixing the air filter mounting bracket to the batterydrip tray.3. Undo the two fixing nuts (3a) and move the connections/electricalwiring mounting bracket (3b) aside.4. Release the accelerator cable from the fastening on the bracket.2018771
0Removing201Refitting211. Unscrew the screw.2. Remove the frame (2a) and take it off the check clamps (2b).3. Unscrew the screws.4. Remove the speedometer/odometer (4a) from from support and moveit.5. Disconnect the electric connections (5a, 5b).2018847
5560B03
0Removing201Refitting211. Unscrew the screw.2. Remove the frame (2a) and take it off the check clamps (2b).3. Unscrew the screws.4. Extract the speedometer (4a) from the support (4b) e move it.5. Disconnect the electric connections (5a, 5b).2018848
5560B06
0Removing201Refitting21For the replacement of lampsof the speedometer/odometer proceed as follows.3238496-5560B02kilometre/mileometer - r r1. Turn and remove the lamp holder of the instrument lamp (1a) orthe lamp holder of the display lamp (1b).2. Remove the lamp from lamp holder. Pressure joint.2018849
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative (-) battery terminal.3237940-2127A20cover of control lever/handle for manual gearboxwith hydraulic selection - r r1. Remove the trim.2. Disconnect the electrical connection from the electro-hydraulicselection manual gear lever trim.3. Undo the bolts (3a) and remove the electro-hydraulic selectionmanual gear lever trim.2017111
2127A20
0Removing201Refitting211. Release the springs for the trim positioned as illustrated inthe diagram and lift the actual trim as much as necessary.2. Loosen the band (2a) and remove the electro-hydraulic selectionmanual gear lever/grip trim (2b).2017112
0Removing201Refitting21 Proceed with removal 3238527-5580C18air bag module - r+r . 769PROCEED AS FOLLOWS FOR THE RIGHT LEVER.1. Disconnect the electrical connection for the horn, then pushthe connector on the steering wheel as far as necessary to accessthe electrical wiring for the gear selector control lever. 2. Disconnect the electrical connection for the gear selector controllever.3. Undo the bolt (3a) and remove the gear selector control lever(3b) releasing the electrical wiring.2069760
0Removing201Refitting211. Disconnect the electrical connection.2. Turn IU+2019 switch (2a) anticlockwisely of about 60° and extractit.To make the opening easier operate by a wrench on the exagonalsection (2b) of the IU+2019 switch. 2018839
0Removing201Refitting211. Open the boot lid, turn and undo the lower studs securing theupper trim.2. Lower upper trim (2a) and unscrew knob (2b) securing the thirdbrake light.3. Prise out the brake light and remove.4. Prise electrical connection (4a) out of support (4b) and disconnect.Recover the light cluster.2018841
5550D17
0Removing201Refitting213238489-5550D16third stop light - r+r1. Unscrew the bolts and remove the mount from the light.2. Undo the bolts.3. Remove the bulb holder.4. Remove the bulbs (press-fit type)2018843
0Removing201Refitting21Place the car on an auto lift.1. Lift the car and disconnect the electrical connection of thereserving light switch.2. Unscrew and take the reserve light switch off.2018845
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Release the buttons (1a) and remove the right console closingdevice (1b).2017928
Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Service/end of line self-calibration'.Continue with the procedure on the Examiner.
2127E10
0Removing201Refitting21Ensure that the ignition key is in OFFposition, then disconnect the negative battery terminal.1. Undo the nuts (1a) and remove the cover under the dashboard onthe passenger side (1b).2017208
2127E30
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-).3237940-2127A20cover of control lever/handle for manual gearboxwith hydraulic selection - r r . 1. Remove the trim.2. Disconnect the electrical connection for the electro-hydraulicgear selection city function selection switch.3. Disconnect the electrical connection from the electro-hydraulicselection manual gear lever trim.4. Undo the bolts (4a) and remove the electro-hydraulic gear selectioncity function selection switch (4b).2017216
2127E40
0Removing201Refitting213238429-5530B10battery - r+r3238435-5530B52Battery DRIP TRAY/SUPPORT - R.R.1. Disconnect the front battery electrical connection.2. Disconnect the ABS electrical connection.3. Disconnect the electrical connection from the gear engagementsolenoid valve.4. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.2017219
2127E42
0Removing201Refitting21 Proceed with the removal 3238429-5530B10battery - r+r Proceed with the removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R.1. Release the electrical wiring from the mounting bracket.2. Disconnect the electrical connection from the gear engagementsolenoid valve 1.3. Disconnect the electrical connection from the gear engagementsolenoid valve 2.4. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.5. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.2017223
2127E44
0Removing201Refitting21 Proceed with the removal 3238429-5530B10battery - r+r Proceed with the removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R.1. Release the electrical wiring from the mounting bracket.2. Disconnect the electrical connection from the gear engagementsolenoid valve 1.3. Disconnect the electrical connection from the gear engagementsolenoid valve 2.4. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.2017227
2127E50
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner.3238429-5530B10battery - r+r . 3238435-5530B52Battery DRIP TRAY/SUPPORT - R.R. . 1. Disconnect the electrical connection from the electro-hydraulicgear selection hydraulic circuit pressure sensor.2. Undo and remove the electro-hydrauilc gear selection hydrauliccircuit pressure sensor.2017231
2127E52
0Removing201Refitting21Position the vehicle on the ramp.Ensure that the ignition key is in OFFposition, then disconnect the negative battery terminal.3238966-7055B54under-engine guard - r r . 1. Disconnect the electrical connection from the electro-hydraulicgear selection input shaft speed sensor.2. Undo and remove the electro-hydraulic gear selection input shaftspeed sensor.2017233
Position the vehicle on a flat surface.Check fluid level and top up if necessary.Work with the engine cold.Turn the ignition key to the ON position.Wait for the pump to come on and go off.Immediately after it has gone off, check the level of hydraulicfluid in the hydraulic selection gearbox using the special dipstickin the reservoir cover.If necessary, top up the level using therecommended fluid.Turn the ignition to the OFF position.
0Removing201Refitting213237946-2127C12hydraulic gear selection fluid reservoir - r r . 1. Release the electrical connection for the electro-hydraulic selectionsystem electric pump from the support.2. Release the pipe between the electro-hydraulic selection hydraulicunit and the fluid reservoir from the band on the support.3. Release the pipe between the electric pump and the electro-hydraulicselection hydraulic unit from the band on the support.2017134
2127C12
0Removing201Refitting211. Remove the electro-hydraulic selection gearbox hydraulic circuitfluid reservoir cap.Drain the electro-hydraulic selection gearbox hydrauliccircuit fluid reservoir.2. Loosen the band fixing the electro-hydraulic selection gearboxhydraulic circuit fluid reservoir.3. Disconnect the supply and return pipes from the electro-hydraulicselection gearbox hydraulic circuit fluid reservoir.4. Remove the electro-hydraulic selection gearbox hydraulic circuitfluid reservoir.2017146
2127C18
0Removing201Refitting211. Remove the electro-hydraulic gear selection system hydrauliccircuit fluid reservoir cap.Drain the electro-hydraulic gear selectionsystem hydraulic circuit fluid reservoir.2. Release the electrical connection for the electro-hydraulic gearselection system electric pump from the support.3. Loosen the fixing bands and remove the pipe between the hydrauliccircuit fluid reservoir and the electro-hydraulic gear selectionelectric pump.2017149
2127C20
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner.3238429-5530B10battery - r+r3238435-5530B52Battery DRIP TRAY/SUPPORT - R.R.1. Remove the electro-hydraulic gear selection system hydrauliccircuit fluid reservoir cap.Drain the electro-hydraulic gear selectionsystem hydraulic circuit fluid reservoir.2. Release the electrical connection for the electro-hydraulic gearselection system electric pump from the support.2017154
2127C22
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner.1. Remove the electro-hydraulic selection gearbox hydraulic circuitfluid reservoir cap.Drain the electro-hydraulic selection gearbox hydrauliccircuit fluid reservoir.2. Release the electrical connection for the electro-hydraulic gearselection system electric pump from the support.2017164
2127C30
0Removing201Refitting21Connect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner.Ensure that the ignition key is in OFFposition, then disconnect the negative battery terminal.3237946-2127C12hydraulic gear selection fluid reservoir - r r . 1. Release the electrical connection for the electro-hydraulic gearselection system electric pump from the support and disconnect it.2. Release the pipe between the electro-hydraulic selection hydraulicunit and the fluid reservoir from the band on the support.3. Release the pipe between the electric pump and the electro-hydraulicselection hydraulic unit from the band on the support.2017170
2127C40
0Removing201Refitting21Place the gear lever in neutral.Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Remove the electro-hydraulic gear selectionsystem hydraulic circuit fluid reservoir cap and drain the reservoirusing a syringe.767Do not reuse the fluid from thehydraulic gear selector system circuit.1. Disconnect the pipe between the electro-hydraulic gear selectionhydraulic unit and the fluid reservoir, hydraulic unit side.2. Undo the connector (2a) and disconnect the pipe between the electricpump and the electro-hydraulic gear selection hydraulic unit (2b),hydraulic unit side. 767The fluid recovered should notbe reused.2017183
2127C25
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . Proceed with removal 3238966-7055B54under-engine guard -r r . 1. Undo the connector and disconnect the pipe between the selectionsolenoid valve and the engagement/selection actuator, hydraulicactuator unit side.2069788
2127C26
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . Proceed with removal 3238966-7055B54under-engine guard -r r . 1. Undo the connector and disconnect the pipe between the unevengear engagement solenoid valve and the engagement/selection actuator,hydraulic actuator unit side. 2069792
2127C27
0Removing201Refitting21Connect the Examiner diagnostic equipment.Keep the brake pedal depressed.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . Proceed with removal 3238966-7055B54under-engine guard -r r . 1. Undo the connector and disconnect the pipe between the even gearengagement solenoid valve and the engagement/selection actuator,hydraulic actuator unit side.2069796
2127C28
0Removing201Refitting21Connect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . 1. Undo the connector and disconnect the pipe between the clutchengagement solenoid valve and the clutch hydraulic actuator, hydraulicactuator unit side.2069800
2127C44
0Removing201Refitting21Position the vehicle on the rampConnect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . 1. Undo the upper bolt fixing the pressure accumulator collar tothe gearbox.2069818
0Removing201Refitting21Place the gear lever in neutral, N.Connect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . 1. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.2. Disconnect the electrical connection from the electro-hydraulicgear selection position sensor.3. Undo the connector and disconnect the pipe between the selectionsolenoid valve and the engagement/selection actuator, gear engagementelectro-hydraulic selection device side. 4. Undo the connector and disconnect the pipe between the even gearengagement solenoid valve and the engagement/selection actuator,gear engagement electro-hydraulic selection device side. 5. Undo the connector and disconnect the pipe between the unevengear engagement solenoid valve and the engagement/selection actuator,gear engagement electro-hydraulic selection device side. 2069823
0Removing201Refitting21Position the vehicle on the rampConnect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner.Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 3238966-7055B54under-engine guard -r r . 1. Disconnect the electrical connection of the gear selection solenoid.2. Undo the bolts (2a) and gear selection solenoid valve (2b).2069829
2127C56
0Removing201Refitting21Connect the Examiner diagnostic equipment.Select 'Alf 156 Selespeed' on the Examiner.Select 'Control Unit Test' on the Examinerand select the 'Marelli Selespeed Automatic Transmission'.Press 'Active Diagnosis' on the Examinerand select 'Accumulator depressurizing'.Continue with the procedure on the Examiner. Proceed with removal 3238429-5530B10battery - r+r . Proceed with removal 3238435-5530B52Battery DRIP TRAY/SUPPORT- R.R. . Proceed with removal 3237525-1048A10air cleaner filtering element- replace . 1. Disconnect the electrical connection from the clutch controlsolenoid.2. Undo the bolts (2a) and remove the clutch control solenoid valve (2b).2069830
0Removing201Refitting21Disconnect the battery negative (-) terminal.1. Disconnect the electrical connection from the hot-film air flowmeter. Move the relays fastened to the batterycradle to one side.2. Disconnect the pipe carrying air to the throttle body from theflow meter.3. Undo bolts (3a), remove half-rings (3b) and air flow meter (3c).2013556
1056B10
0Removing201Refitting21Ensure that the ignition key is in thestop position, then disconnect the battery negative terminal.1. Disconnect the electrical connection from the air flow meter.Move the relays fastened to the batterycradle to one side.2. Disconnect the pipe carrying air to the throttle body from theflow meter.3. Undo bolts (3a), remove half-rings (3b) and air flow meter (3c).2013557
1056B17
0Removing201Refitting21Ensure that the ignition key is in stopposition, then disconnect the battery negative terminal.1. Disconnect the oil vapour recirculation pipe from the right cylinderhead.2. Disconnect the corrugated hose from the throttle body and moveaside.2013558
0Removing201Refitting21- 1072B42 left hand or right hand inlet manifold (one) - r+r 767Before any interventions on componentsof the fuel system, discharge the pressure in the system using toolN. 1.870.684.000 connected to the specific valve located on thefuel distribution manifold.1. Disconnect the fuel inlet hose, then plug to prevent fuel escaping.2. Disconnect the electrical connections from the injectors.3. Undo the bolts (3a) and remove the complete fuel pipe (3b) completewith fuel injectors (3c).2013562
0Removing201Refitting211. Remove the retainers (1a) and remove the fuel injectors (1b)from the fuel manifold pipe.2. Remove the O-rings from the fuel injectors.2013564
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal.1. Working from the passenger compartment, undo bolts (1a) and removeinjection/ignition control unit guard (1b).2. Disconnect the electrical connections from the fuel injection/ignitioncontrol unit.767Follow the disconnection order:D - E - F - C - B - A.3. Undo nuts (3a) and remove injection/ignition control unit (3b).2013565
1056B90
0Removing201Refitting21Disconnect the battery negative (-) terminal.Raise the car.1. Disconnect the electrical connection for the air conditionercompressor electromagnet.2013568
1056B14
0Removing201Refitting213237529-1048A34sleeve(s) from flow meter to air supply capacitycase - r + r1. Disconnect the constant idle actuator electrical connection.2. Disconnect both coolant inlet and outlet pipes (2a-2b) from thethrottle body.3. Disconnect the throttle position switch (potentiometer) electricalconnection.4. Disconnect the accelerator cable.Release the pipes from the fasteners onthe bracket under the throttle body.5. Undo the four bolts (5a) and remove throttle body (5b) with itsgasket.2014090
1056B15
0Removing201Refitting21Ensure that the ignition key is in stopposition, then disconnect the battery negative terminal.3237652-1016A40ignition coil cover on cylinder head- r+r3237529-1048A34sleeve(s) from flow meter to air supply capacitycase - r + rDisconnect the electrical connection fromthe throttle body integral with the M.D.S.1. Disconnect electrical connections (1a) and (1b) from the injection/ignitioncontrol unit and earth lead (1c) from the throttle body integralwith the M.D.S.2. Disconnect the accelerator cable from the throttle body integralwith the M.D.S.3. Disconnect the injection/ignition wiring from the mounting bracket.4. Undo bolts (4a) and remove the throttle body integral with theM.D.S. (4b) complete with the injection/ignition control unit (4c).2014091
1056B19
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the battery negative terminal.3237544-1056B82injection/ignition system e.c.u. (one) - r + r . 1. Disconnect the earth lead from the injection control unit support.2. Disconnect the oil vapour recovery pipe from the corrugated hose.3. Loosen the bands and remove the second section of the corrugatedhose after having released it from the bracket.4. Disconnect the electrical connection (4a) from the butterflycasing integrated with D.V.L. and release the wiring from the band(4b).2014095
1056B40
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the intake air temperaturesensor.2. Loosen collar (2a), withdraw air sleeve (2b) from the throttlebody and move to one side.3. Unscrew both power steering fluid reservoir bolts and move toone side.2014098
1056B43
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the constant idle actuator electrical connection.2. Unscrew both retaining bolts and remove the throttle body actuator.Recover the seal.2014100
1056B46
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the intake air temperaturesensor.2. Withdraw and remove the intake air temperature sensor from theair sleeve.2014101
1056B48
0Removing201Refitting21Disconnect the battery negative terminal.
1056B60
0Removing201Refitting21Disconnect the battery negative (-) terminal.
1056B87
0Removing201Refitting21Ensure that the ignition key is in thestop OFF, then disconnect the battery negative terminal.1. Disconnect electrical connections (1a) and (1b) from the injection-ignitioncontrol unit.2. Release the electrical wiring from the fastening on the ignition/injectionsystem control unit mount.2014110
1056B89
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the battery negative terminal.3237544-1056B82injection/ignition system e.c.u. (one) - r + r . 1. Disconnect the earth lead from the injection control unit support.2. Disconnect the oil vapour recovery pipe from the corrugated hose.3. Loosen the bands and remove the second section of the corrugatedhose after having released it from the bracket.4. Disconnect the electrical connection (4a) from the butterflycasing integrated with D.V.L. and release the wiring from the band(4b).2014117
0Removing201Refitting213238803-7040A65passenger compartment box lock , one , r r1. Undo the nuts and withdraw the electronic automatic transmissioncontrol unit as much as necessary. 2. Disconnect the electrical connections (2a) and (2b), then removeelectronic automatic transmission control unit.2017422
0Removing201Refitting21Position the vehicle on the ramp.3238429-5530B10battery - r+r . 1. Disconnect the electrical connection for the automatic transmissionfluid temperature sensor and release the wiring from the securingbands.2. Undo nut (2a) and bolt (2b) then remove the automatic transmissionfluid temperature sensor cover bracket (3c).3. Undo the automatic transmission oil temperature sensor completewith wiring and remove.767Collect the automatic transmissionfluid which leaks out in a suitable container.2017433
Carry out a preliminary check of the automatictransmission fluid level when cold as follows.Park the car on level ground and engagethe hand brake.With the engine idling, starting from theP position select all the other gears 2 or 3 times then return tothe P position. Withdraw the oil level dipstick, cleanit, then insert it fully into its housing.Withdraw the dipstick again and check thatthe oil level is between the MIN and MAX references on the sideof the stick marked "COLD".If the oil level is low, top up with thespecified oil.767The final gearbox oil level checkmust be carried out with the engine and gearbox at normal operatingtemperature (gearbox oil temperature 70° - 80° C), so the carshould be driven for an appropriate time before the check.Carry out the final check of the automatictransmission fluid level when warm as follows.Park the car on level ground and engagethe hand brake.With the engine idling, starting from theP position select all the other gears 2 or 3 times then return tothe P position. Withdraw the oil level dipstick, cleanit, then insert it fully into its housing.Withdraw the dipstick again and check thatthe oil level is between the MIN and MAX references on the sideof the stick marked "HOT".If the oil level is low, top up with thespecified oil.The quantity of oil need for filling ifnecessary is as follows:
0Removing201Refitting213238633-7010A04rear side door waterguard protection - r r or arrange with door panel removed1. Disconnect, from the lock side, the linkage connecting to theouter handle.2. Release the rod guide springs from the door frame.3. Disconnect the rod (3a) from the idler (3b).4. Undo the bolts fixing the inner handle.5. Unscrew the catch retaining bolts. 6. Move the lock over slightly.7. Disconnect the electrical connections (7a, 7b), then extractthe lock.8. If necessary, separate the two rods from the lock.2019053
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.