DescriptionThere are three ashtrays in the car: one is in the centre ofthe dashboard, and two are in the rear doors.The front ashtray is lit when the side lightsare on; it houses a standard power point; the ring round the powerpoint is lit with the side lights on. The cigar lighter resistanceis located in the socket, but it can be used for connection to otherinstruments or equipment (provided they operate at 12 V). To operatethe cigar lighter, simply press the knob: after a few seconds itpops out automatically, ready for use.The socket has a heat protection device:if devices with high energy absorption are connected, this protectioncuts off the supply.The current socket circuit is protectedby a special fuse and is operated by the relay which is excludedwhen the ignition is switched on and is located in the junctionunit.The sockets are only supplied when the ignitionis switched ON.
Functional description The power socket / cigarette lighter P50 is supplied (atpin 2) by the line controlled by the ignition (INT/A) for the relay R1 protectedby the fuse F15 : both are housed in the junction unit B1 . Pin 3 of socket P50 provides theearth from C20 . The ring nut for the power socket is litup (at pin 1) when the side lights are on by means of the line comingfrom the steering column switch unit H5 switch and is protectedby the controls illumination fuse B11 up to 2/99 or fuse F4 of theadditional fuse unit B98B from 2/99. The same supply line with the side lightson also lights up the ashtray light G35 .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the car on a ramp.Undo the bolt securing the bracket on thebattery mount.Release the battery from the anchoragebracket complete with strap and remove.
5530B14
769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour:a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery;a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For more details 3238420See subassembly5530 CURRENT GENERATOR . 768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360').Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows: If the voltage without load is less than12.10 V, replace the battery ( 32384295530B10battery - r+r ). If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery ( 32384305530B14battery - recharge ). If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
5530B22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the car on the liftingbridge.1. Open engine compartment cap and disconnect battery negative terminal.2. Disconnect mass terminal on side member.3. Lift the car and disconnect mass terminal on gearbox.4. Lower the car again and remove battery earth lead.2018767
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negative terminal.1. Open the protective cover2. Loosen the nut and disconnect the ABS supply lead3. Loosen the nut and disconnect the starter motor supply lead4. Undo the clip and undo the box retaining bolts.5. Loosen the battery positive terminal nut.2018769
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238429-5530B10battery - r+rRelease the air duct hose from the mountingbracket on the drip tray. Remove the relay shield.1. Release the relays from the battery drip tray and remove them.2. Undo the nut fixing the air filter mounting bracket to the batterydrip tray.3. Undo the two fixing nuts (3a) and move the connections/electricalwiring mounting bracket (3b) aside.4. Release the accelerator cable from the fastening on the bracket.2018771
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Please note the following warning.7691. Working on both sides of the longitudinal mount, prise off thecovers using the appropriate tool. 7692. Undo bolts (2a) and recover washers (2b) and gaskets (2c).3. Remove the longitudinal mount.4. Recover the gaskets.2019528
7065C30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Lower handle and remove badge.2. Unscrew screws.3. Remove handle (3a) by removing it from stops (3b).2019529
7065C34
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew I' sun blind fixing screw.2. Remove I' sun blind (2a) by releasing it from stop (2b).3. Remove and lift I' grab handle badge.4. Unscrew I' grab handle fixing screw.5. Remove l' grab handle.2019530
7065C42
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the ashtray and undo the screws.2. Move the ashtray over slightly.3. Disconnect the electrical connections (3a, 3b).2019531
7065C84
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove radio compartment (1a) from stops (1b) and extract itslightly.2. Disconnect electric connections (2a, 2b) from chambers.2019535
7065C58
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working on the interior rearview mirror mounting, remove thecover, releasing it from the retainers. 2. Disconnect the electrical connections (2a (2b).3. Working on the recess (3a), open the cover (3b) of the rain sensor.2019536
7065C68
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Only for vehicles equipped with a Telepass holder. Undo the bolt(1a), move the trim (1b) and disconnect the electrical connection(1c). 2019540
7065C69
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21The following procedure showsplate reattachment since it is not possible to detach plate fromglass if it has been properly fixed.769
7065C72
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238986-7065C42ashtray (one) r+r1. Take out the ashtray.2. Extract the cigar lighter housing (2a) using the special tool.The tool should engage in the recesses (2b) of the cigar lighterhousing.2019544
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connections.2. Open the socket cover.3. Wtihdraw the socket (3a) (cigarette lighter type) using the specialtool (3b).767The tool must engage in the recesses(3c) of the cigarette lighter seating.4. If necessary, remove the ring nut with cover from its seating.2019550
Русский
