DescriptionThe direction indicators and hazard warninglights delimit the outer dimensions of the car.The left and right direction indicatorsare operated by raising or lowering the appropriate lever on thestalk unit.The hazard warning lights (right and leftdirection indicators operated simultaneously) are turned on by thepressing the red button at the centre of the dashboard.The direction indicators work with the ignitionon, while for safety reasons, the hazard warning lights can be turnedon at any time, as they are supplied directly from the battery.The circuit for the direction indicatorsand hazard warning lights is protected by a single fuse.Two warning lights on the instrument panel(rev counter module), which also flash, show when the right or leftdirection indicator is on.The red hazard warning light button containstwo leds: the first green one is ignition-operated and lights upthe specific symbol; The second red light comes on intermittentlywhen the hazard warning lights are operated.The hazard warning lights are also activatedby the alarm system, which is connected directly to the power supplyto the lights.
Functional description The circuit is controlled by the hazardwarning lights switch H20The intermittent device is locatedon the steering column switch unit H5. It is connected to earthat pin 7 of connector A and receives a supply signal at pin 7 ofconnector D through switch H20:when the hazard lights are not off, the supply is controlledby the ignition (INT/A) from fuse F6 of the additional fuse boxB98B.when the hazard warning lights are switched on, the supplyis direct from the battery through fuse F9 of the junction unitB1 and maxifuse J/B1of fuse B99. The intermittent device produces a signalwhich supplies the switch for the direction indicators on the steeringcolumn switch H5 and the switch H20 . The operation, in one direction or another,of the steering column switch lever H5 supplies the rightdirection indicators ( F11 , F21 , F31 ) or theleft ones ( F10 , F20 , F30 ). At the same time the warning light, locatedin the rev counter module E15 , comes on. Pressing the switch H20 closes threecontacts which simultaneously supply all the lights (right branchand left branch) close and the red LED in the actual switch whichlights up the symbol. In switch H20 there is also a greenLED which comes on when the ignition is switched on (INT/A). All the hazard warning lights are also operatedby the alarm system control unit M30 (pins 1 and 2 of connectorB), which is connected directly to the light power supply SeeE7015 ALARM .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the car on a ramp.Undo the bolt securing the bracket on thebattery mount.Release the battery from the anchoragebracket complete with strap and remove.
5530B14
769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour:a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery;a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For more details 3238420See subassembly5530 CURRENT GENERATOR . 768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360').Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows: If the voltage without load is less than12.10 V, replace the battery ( 32384295530B10battery - r+r ). If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery ( 32384305530B14battery - recharge ). If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
5530B22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the car on the liftingbridge.1. Open engine compartment cap and disconnect battery negative terminal.2. Disconnect mass terminal on side member.3. Lift the car and disconnect mass terminal on gearbox.4. Lower the car again and remove battery earth lead.2018767
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negative terminal.1. Open the protective cover2. Loosen the nut and disconnect the ABS supply lead3. Loosen the nut and disconnect the starter motor supply lead4. Undo the clip and undo the box retaining bolts.5. Loosen the battery positive terminal nut.2018769
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238429-5530B10battery - r+rRelease the air duct hose from the mountingbracket on the drip tray. Remove the relay shield.1. Release the relays from the battery drip tray and remove them.2. Undo the nut fixing the air filter mounting bracket to the batterydrip tray.3. Undo the two fixing nuts (3a) and move the connections/electricalwiring mounting bracket (3b) aside.4. Release the accelerator cable from the fastening on the bracket.2018771
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the screw.2. Remove the frame (2a) and take it off the check clamps (2b).3. Unscrew the screws.4. Remove the speedometer/odometer (4a) from from support and moveit.5. Disconnect the electric connections (5a, 5b).2018847
5560B03
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the screw.2. Remove the frame (2a) and take it off the check clamps (2b).3. Unscrew the screws.4. Extract the speedometer (4a) from the support (4b) e move it.5. Disconnect the electric connections (5a, 5b).2018848
5560B06
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21For the replacement of lampsof the speedometer/odometer proceed as follows.3238496-5560B02kilometre/mileometer - r r1. Turn and remove the lamp holder of the instrument lamp (1a) orthe lamp holder of the display lamp (1b).2. Remove the lamp from lamp holder. Pressure joint.2018849
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238952-7055A43central front grille - r r3238951-7055A41RIGHT FRONT GRILLE - R.R. (leftand right) It is advisable to place the vehicle on a lift.1. Undo the bolts fixing the end of the front bumper.2. Release the wheel arch liner from the front bumper using thespecial tool in the area where the bolts were removed. 3. Working from the bottom, undo the two bolts securing the bumperto the wing.2018790
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts.2. Remove control unit (2a) by disconnecting from electrical connection(2b).2018803
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Rotate the cover in an anti-clockwise direction and extract it.2. Extract the bulb holder and bulb (press fit).3. Extract the bulb from the bulb holder.2018810
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238952-7055A43central front grille- r r . 3238951-7055A41RIGHT FRONT GRILLE - R.R. (right andleft). 767It is advisable to place the vehicleon a lift.1. Undo the bolts fixing the ends of the front bumper.2. Release the wheel arch liner from the front bumper, using thespecial tool, in the area where the bolts were removed. 3. Working from the bottom, undo the two bolts securing the bumperto the wing.2018811
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the ash-tray and take the warning light switch off.2. Disconnect the electrical connections (2a, 2b) and recover theswitch.2018836
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Take the side flasher off by the suitable tool. Operate fromthe shown side.2. Disconnect the electrical connection and recover the side flasher.3. If necessary, turn anticlockwisely and extract the light holder(3a) and take the light off(3b).The light is pressure inserted.2018838
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the boot lid and undothe two side bolts fixing the inner trim.2018778
5540A68
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the boot lid and undo the bolts fixing the inner lining.2018781
5540A78
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the boot lid and undo the bolts fixing the inner lining.2018784
5540A80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the trunk lid panel and unscrew the two clamping screwsof the light fender.2. Unloose the check tongs (2a) and extract the light holder (2b).3. Take the lights off from the light holder.(Bayonet joint)2018787
5540A94
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Operating from the right side, by a screwdriver, and take thelight off.2. Disconnect the electrical connection.2018788
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor (3a) releasing the toothed wheel (3b) from thecam rack.2018552
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the motor retaining bolt.2. Disconnect the electrical connections for the motor (2a, 2b,2c, 2d).3. Remove the motor (3a) releasing its connection (3b).2018560
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238793-7040A26steering column trim- r+r3238799-7040A37fuse box cover - r r1. Disconnect the antenna connection from the power unit.2. Remove the antenna from the starting block.3. Free the cable from the check clamps.4. Remove the antenna unit.2018926
5580E12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238799-7040A37fuse box cover - r r1. Unscrew the shunt power unit screws .2. Remove the shunt power unit.3. Disconnect the anti-theft device power unit.4. Remove the anti-theft device power unit.5. Disconnect the electric connection.6. Disconnect thel'antenna connection.2018927
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238843-7040H38central pillar upperelement - r r1. Prise the volumetric sensor from its seat in the pillar trim.2018930
5580E24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238799-7040A37fuse box cover - r r1. Disconnect electrical connections (1a), (1b).2. Undo the nut.3. Remove the switch and bridge.2018931
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the bonnet lid and remove the buttons retaining the uppertrim using the special tool.2. Lower the upper trim and disconnect the electrical connectionfor the receiver.3. Unscrew the nuts.4. Remove the receiver.2018932
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238964-7055B42Additional FRONT WHEELARCH (one), left or right - R.R.1. Unscrew the control unit bracket retaining nuts.2. Move control unit bracket (2a) and disconnect electrical connections(2b, 2c).3. Unscrew the nuts retaining the control unit to the bracket.4. Recover the control unit by taking off its bracket.2018935
English
