DescriptionThe rearscreen wiper is operated by turningthe ring nut on the end of the lever located on the right of thesteering wheel.By pushing the lever gently towards thesteering wheel the rearscreen washer function is activated; thesame pump is used as for the windscreen washer (two-way), but itrotates in the opposite direction and sends the detergent fluid tothe rear.If the lever is kept pressed, the rearscreenwiper comes on and operates for a few moments after the lever isreleased. When the lever is released, the windscreen wipers willcontinue to operate for several strokes.The rearscreen wash/wipe can only be operatedwith the ignition switched ON.The windscreen wash/wipe circuit is protectedby a specific fuse and is operated by the ignition-operated relaylocated in the junction unit.
Functional description The stalk unit H5 is supplied atpin 3 of connector D from the ignition-operated line (INT/A) ofthe relay R1 protected by the fuse F14 : both arecontained in the junction unit B1 . The rear wiper is activated by stalk switch H5 viaa signal sent by pin 1 of connector D to rear wiper motor N16 . When operated, the windscreen washer switchon the steering column switch unit H5 sends two signals frompin 8 and pin 9 of connector A, which reach the pump for operatingthe windscreen washer N22 directly. The motor is operatedupon a command from stalk switch H5 in the opposite mannerto that described for the washer function (when the motor is operatedin reverse, it sends fluid to the back instead of to the front). One of the two signals (pin 2 of connectorD of H5 ) is sent to electronic device inside rear wiper motor N16 that controls the operation of the rear wiper in conjunctionwith the rear washer. The rear wiper motor N16 is thenconnected to earth. It consists of the actual geared motor, theend of travel contacts and the electronic adjustment and controldevice.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Turn IU+2019 switch (2a) anticlockwisely of about 60° and extractit.To make the opening easier operate by a wrench on the exagonalsection (2b) of the IU+2019 switch. 2018839
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the boot lid, turn and undo the lower studs securing theupper trim.2. Lower upper trim (2a) and unscrew knob (2b) securing the thirdbrake light.3. Prise out the brake light and remove.4. Prise electrical connection (4a) out of support (4b) and disconnect.Recover the light cluster.2018841
5550D17
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238489-5550D16third stop light - r+r1. Unscrew the bolts and remove the mount from the light.2. Undo the bolts.3. Remove the bulb holder.4. Remove the bulbs (press-fit type)2018843
5550D18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238117-3380A44handbrake/linkage protection- r+r1. Unscrew the screw.2. Move IU+2019switch.3. Disconnect the electrical connection and recover IU+2019switch.2018844
5550D22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the car on an auto lift.1. Lift the car and disconnect the electrical connection of thereserving light switch.2. Unscrew and take the reserve light switch off.2018845
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Lift the bonnet lid and move the jet with the tool.2. Disconnect the jet from the pipe.2018596
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Lift the wiper arm.2. Press on the end with stop (2a) of the support (2b) and removethe blade (2c) from the arm end.2018600
5050B32
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238363-5050B28windscreen wiper blade/s- r+r1. Lift the bonnet lid and move the nut cover.2. Unscrew the nut.3. Remove the wiper arm.2018601
5050B34
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Lift the bonnet lid and move the nut covering.2. Unscrew the nut.3. Remove the wiper arm.2018602
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Disconnect stop springs.3. Remove the intermittent function.2018606
5050B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238365-5050B34windscreen wiper arm/scomplete with blade - r+r1. Unscrew the left lining.2. Release the lining from the stops with l' the tool, then moveit.3. Remove the motor guard.4. Disconnect electrical connections (4a, 4b).5. Disconnect stop springs.6. Remove the intermittent function l'.2018607
5050B54
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213238365-5050B34windscreen wiper arm/s complete with blade - r+r (rightside). 1. Release the protection.2. Undo the bolts fixing the right trim.3. Move the trim after having released the inner retainers usingthe special tool.2018608
5050B64
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working on the interior rear view mirror mounting, open the cover.2. Move the rain sensor slightly.7693. Disconnect the electrical connection and recover the sensor.2018611
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release the end (1a) of the blade from retainer (1b), then withdrawfrom the other retainers (1c).2019574
7095B82
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Lift up the nut cover.2. Undo the nut.3. Remove the wiper arm.4. Remove the protection if necessary.2019575
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Release intermittence (2a) from retainer (2b), then from retainer(2c).3. Recover the intermittence. Take care not to damage the contactstrips (3a).2019579
Electric windscreen / rearscreen washer pump motor
English
