DescrizioneIl riscaldatore supplementare consente diintegrare il riscaldamento del liquido di raffreddamento del motoresubito dopo l'avviamento e durante la marcia, per accelerare ilraggiungimento e mantenere la temperatura ottimale di funzionamentodel motore e del riscaldatore dell'abitacolo.Il dispositivo funziona in modo completamenteautomatico e si attiva solo quando il motore e in moto, con temperaturaesterna inferiore o uguale a +5°C e temperatura liquido di raffreddamentoinferiore a 60°C.Quando il liquido di raffreddamento raggiungei 61°C, la centralina elettronica riduce la potenza del bruciatoree ne interrompe il funzionamento al raggiungimento dei 72°C, perriattivarla automaticamente quando la temperatura del liquido scendea 60°C. Se invece, dopo la riduzione della potenza del bruciatore,la temperatura del liquido inizia subito a scendere, la centralinainterviene ripristinando la piena potenza. Per maggiori dettagli vedere Descrizionie Funzionamento 5020L RISCALDATORE ADDIZIONALE . La linea di alimentazione della centralinae protetta da un fusibile della centralina vano motore e da unteleruttore posto nella vasca servizi (dietro la paratia motore).La linea di alimentazione del teleruttoree protetta da un fusibile posto nella centralina di derivazione.
Descrizione funzionale La centralina del riscaldatore addizionale M75 ealimentata al pin 1 (connettore B) direttamente dalla batteria.attraverso la linea protetta dal fusibile F23 della centralina vanomotore B1 . La massa viene portata al pin 2 (connettoreB) attraverso il teleruttore riscaldatore addizionale J36 ,l'interruttore I20 e il teleruttore T1 della centralina diderivazione B2 . Quando il teleruttore T1 viene eccitatotramite la linea (15/54) il suo contatto alimenta, attraverso ilfusibile F6 , la bobina del teleruttore riscaldatore addizionale, J36 ed attraverso il suo contatto la centralina M75 riceveil segnale di massa. Al pin 3 del connettore A di M75 entrail segnale dall'apposito sensore di temperatura K79 che rilevala temperatura aria nel vano motore. Il sensore funziona solo a motore avviato;riceve infatti il segnale di riferimento dall'alternatore(D+); talesegnale e "basso' (di massa) quando l'alternatore non ruota,a motore avviato tale segnale diviene "alto' (12 V) e alimentail sensore. 3295046VedereE5010AVVIAMENTO E RICARICA Dal pin 6 (connettore A) viene comandatal'elettropompa del riscaldatore addizionale N44 , che e collegataa massa attraverso l'interruttore inerziale I50 . Questo,in caso di urto, interrompe il circuito fermando possibili e pericolose erogazionidi combustibile. Inoltre un intervento dell'interruttoreinerziale diseccita il teleruttore J36 . La centralina M75 e dotata di unsistema di autodiagnosi, che puo essere utilizzato collegandosial connettore R10 attraverso il pin 2 (connettore A). 3295357VedereE8010CONNETTORE MULTIPLO DI DIAGNOSI .
0Stacco201Riattacco213300112-5505A18CENTRALINA MULTISERVIZIintegrati - S.R. . 1. Svitare la vite (1a) ed arretrare la centralina di derivazionequanto basta a scollegare le connessioni elettriche (1b).767Per una precisa identificazionedelle connessioni elettriche vedere Sezione Schemi Elettrici.2. Rimuovere la centralina di derivazione.2010592
0Stacco201Riattacco21 Accertarsi che la chiave diaccensione sia in posizione "STOP", quindi scollegareil morsetto (-) della batteria (fare riferimento a op. 33001495530B10BATTERIA - S.R. ). 1. Svitare la vite (1a) e aprire il coperchio accesso fusibili (1b).2. Svitare la vite (2a) e rimuovere la centralina multiservizi integrati(2b) dopo aver scollegato le connessioni elettriche (2c), (2d),(2e), (2f) e (2g).2010595
5505A29
0Stacco201Riattacco21Aprire il coperchio vano motore.1. Disimpegnare i ritegni (1a) e rimuovere il coperchio (1b) dellacentralina di derivazione supplementare.2071293
0Stacco201Riattacco213300152-5530B54COPERTURA batteria -S.R. . Accertarsi che la chiave di accensionesia in posizione "STOP".1. Scollegare i morsetti negativo e positivo dalla batteria.2. Svitare la vite (2a) di fissaggio della staffa (2b) di ritegnobatteria.3. Rimuovere la batteria.2010647
5530B40
0Stacco201Riattacco213300152-5530B54COPERTURA batteria - S.R.1. Premere e disimpegnare i ritegni (1a), quindi rimuovere il coperchio(1b) della scatola di alimentazione su batteria. 2071303
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore.3300477-7040B10RIVESTIMENTO PIANO DI CARICO (piano bagagli) - S.R. . 3299388-1040A70COMPLESSIVO POMPA IMMERSA completa di comando indicatoredi livello - S.R. . Aspirare il combustibile dal serbatoiocon una idonea attrezzatura.3299992-4450B11RUOTA (una) posteriore - S.R. (destra). Svitare le viti e scalzare la parte posterioredel rivestimento vano ruota posteriore destro.1. Scollegare dal separatore vapori combustibile le tubazioni dicollegamento alle valvole sul serbatoio.2. Scollegare l'innesto rapido della tubazione di mandata vaporicombustibile al canister.3. Svitare le viti di fissaggio tubo introduzione combustibile allascocca.4. Allentare la fascetta di fissaggio tubo introduzione combustibileal manicotto.2007299
0Stacco201Riattacco21Aprire lo sportello di accesso al tappoper tubo introduzione combustibile.Svitare e rimuovere il tappo per tubo diintroduzione combustibile.
1040A70
0Stacco201Riattacco21 Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria (fare riferimento a op. 33001495530B10BATTERIA - S.R. ). 3300477-7040B10RIVESTIMENTO PIANO DI CARICO (piano bagagli) - S.R. . 1. Svitare le viti (1a) e rimuovere il coperchio (1b) di accessoal complessivo pompa immersa completa di comando indicatore di livello.2. Scollegare la connessione elettrica dal complessivo pompa immersacompleta di comando indicatore di livello.3. Scollegare gli innesti rapidi delle tubazioni di mandata e ritornocombustibile.2007751
1040A74
0Stacco201Riattacco21- 7045A10 SEDILE ANTERIORE (uno), sx o dx - S.R. . 1. Tagliare lungo la zona pretranciata il tappeto pavimento.2. Svitare le viti di fissaggio interruttore inerziale alla scocca.3. Scollegare la connessione elettrica (3a) e rimuovere l'interruttoreinerziale (3b).2007753
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). Procedere con lo stacco 3300591-7055B54PROTEZIONE/RIPARO sottomotore- S.R. . 1. Svitare il tappo di scarico posto sul radiatore e scaricare illiquido di raffreddamento motore.767Recuperare il liquido di raffreddamentoin un idoneo recipiente.2010428
5020M14
0Stacco201Riattacco211. Svitare le viti (1a) e rimuovere la staffa di supporto (1b) dalgruppo riscaldatore autonomo supplementare.2010449
5020M16
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). 1. Svitare il dado (1a) e spostare lateralmente la centralina dipreriscaldo candelette (1b) dopo aver disimpegnato il relativo cablaggioelettrico (1c) dalla fascetta di fissaggio (1d). 2010455
5020M20
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). Procedere con lo stacco 3300192-5550B30AVVISATORE ACUSTICO(uno), sx o dx - S.R. (destro). 1. Scollegare la connessione elettrica dal sensore temperatura ariaesterna.2. Svitare la vite (2a) e rimuovere il sensore temperatura ariaesterna (2b) completo.3. Operando al banco svitare la vite (3a) e separare il sensoretemperatura aria esterna (3b) e il distanziale (3c) dalla staffadi supporto (3d).2010464
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). 1. Scollegare la connessione elettrica dall'elettropompa dosaggio/mandatacombustibile al riscaldatore autonomo supplementare.2. Allentare le fascette e scollegare le tubazioni di entrata eduscita dall'elettropompa dosaggio/mandata combustibile al riscaldatoreautonomo supplementare.767Tappare opportunamente le tubazioniscollegate per evitare la fuoriuscita di combustibile.3. Svitare la vite (3a) e rimuovere l'elettropompa dosaggio/mandatacombustibile al riscaldatore autonomo supplementare (3b) completadi relativo supporto (3c).2010471
5020M32
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore.1. Allentare la fascetta (1a), svitare il dado (1b) e rimuovereil tubo di scarico per riscaldatore autonomo supplementare (1c).2010472
5020M33
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). Procedere con lo stacco 3299697-1016A10COPERCHIO INSONORIZZANTE- S.R. . 1. Svitare i dadi (1a) e spostare la centralina dell'impianto iniezioneelettronica diesel (1b) dalla relativa staffa di supporto.2010473
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore.1. Allentare la fascetta (1a) e scollegare la tubazione gasolioper riscaldatore supplementare (1b), lato elettropompa.2. Allentare la fascetta (2a) e scollegare il tubo rigido gasolioper riscaldatore supplementare (2b) dal manicotto.3. Disimpegnare dai relativi fissaggi la tubazione gasolio per riscaldatoresupplementare e rimuoverla.2010492
5020M44
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore.1. Allentare la fascetta (1a), svitare i dadi (1b), quindi rimuoverela tubazione gas di scarico per riscaldatore autonomo supplementarecompleta (1c).2010493
5020M52
0Stacco201Riattacco21Posizionare la vettura sul ponte elevatore. Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). Procedere con lo stacco 3300591-7055B54PROTEZIONE/RIPARO sottomotore- S.R. . 1. Svitare il tappo di scarico posto sul radiatore e scaricare illiquido di raffreddamento motore.767Recuperare il liquido di raffreddamentoin un idoneo recipiente.2010495
5020M55
0Stacco201Riattacco211. Svitare le viti (1a) e rimuovere la staffa di supporto (1b) dalgruppo riscaldatore autonomo supplementare.2010503
0Stacco201Riattacco211. Disimpegnare il tubo flessibile di uscita acqua dal gruppo riscaldatoreautonomo dalle mollette di fissaggio.2. Allentare la fascetta (2a) e rimuovere il tubo flessibile diuscita acqua calda dal gruppo riscaldatore autonomo (2b).2010506
5020M90
0Stacco201Riattacco21 Accertarsi che la chiave di accensionesia in posizione "STOP", quindi scollegare il morsetto(-) della batteria ( 3300149-5530B10BATTERIA - S.R. ). Procedere con lo stacco 3299697-1016A10COPERCHIO INSONORIZZANTE- S.R. . 1. Svitare il dado (1a) e spostare lateralmente la centralina dipreriscaldo candelette (1b) dopo aver disimpegnato il relativo cablaggioelettrico dalla fascetta di fissaggio. 2010507
Sensore temp. interna per riscaldatore supplementa
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.