DescriptionThe front courtesy light includes two courtesy lights which operate differently according to the position of the two control switches.With the switches in the right position, the lights come on, whilst in the left position their operation is completely excluded.In the centre position, the lights come on for a timed period when the doors are opened or when the locks are released using the key or the remote control.Both rear interior lights contain a courtesy light that operates in different modes according to the position of the lens, which operates an internal switch.neutral position: light comes on for a timed period when the doors are opened;positioned to one side: lights always off;positioned to the other side: light always on.Courtesy light timing is controlled by control panel control unit sofware as follows:When any of the four doors is opened, all front and rear courtesy lights are operated for a timed period.timed period of 8 seconds when a previously-opened door is reclosed; timing is suspended when the key is turned to MAR (this function allows the driver to enter the car and insert the key in the ignition)timed interval of 3 minutes if one of the doors is left open (this function prevents the battery going flat if the car is left with a door open)When one of the other doors is opened, the current timer count is reset to zero.The courtesy light circuit is protected by a special junction unit fuse. one fuse also protects the supply line controlled by the ignition for the control unit in the control panel.
Functional description The supply for all the courtesy lights arrives directly from the battery via the line for maxifuse CENTR of B5 and fuse F17 of junction unit B1 . The interior lights G10 (front) and G25 and G26 (rear) are switched on - depending on the positions of their internal switch - by an earth signal which is direct (permanently on) or timed. However, the lights on the doors (front left G51 , front right G52 , rear left G55 and rear right G56 ) only ever come on for a timed period. The timed period is managed by the special courtesy lights relay J42 , supplied directly by the battery via the line for maxifuse CENTR of B5 and protected by fuse F17 of junction unit B1 . The timed period is operated by the instrument panel E50 , which sends the signal (from pin 11 of connector B to pin 85 of timer J42 ) as soon as at leas one of the doors is opened via switches N50A , N51B , N55 and N56 , connected to pins 14, 15, 16 and 17 of connector B of E50 , respectively. The timing is interrupted when the ignition 'on' signal is received, which reaches the instrument E50 from the ignition-operated line (INT/A) of the panel - pin 15 of connector A of E50 - through fuse F1 of junction unit B1 . Timing starts from the beginning again if the doors are unlocked via the safety knob: these signals reach the instrument E50 - to pin 12 of connector B - through the switches on the knobs, located in N50A and N51A . The timed period is also activated when the door locks are released using the key or the remote control. This signal comes from switches N50A and N51A and reaches pin 87A of J42 (the same signal reaches the central locking control unit - 3309443SeeE3040CENTRAL LOCKING ).
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use tool (1a) to prise out courtesy light(1b).2. Disconnect the electrical connection and remove the courtesylight.2010968
7040E22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in tthe OFF position, then disconnect the battery negative terminal.1. Remove the under-facia courtesy light (1a) using the tool (1b).2. Disconnect the electrical connection from the under-facia courtesylight and remove it.2010969
7040E24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use the tool shown to take the courtesy light out of its housingon the panel.1. Disconnect electrical cable (2a) from courtesy light (2b) andremove.2010970
7040E26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use the tool to prise the lower courtesy light out of the panel.2. Disconnect electrical connector (2a) from courtesy light (2b)and remove.2010971
7040E28
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use the tool to prise out the courtesy light.2. Disconnect electrical connection (2a) and remove courtesy light(2b).2010972
7040E40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use the tool to prise out the courtesy light.2. Disconnect electrical connection (2a) and remove courtesy light(2b).2010973
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the nuts (2a) and remove the electronic key anti-theft controlunit (2b) after having disconnected the electrical connections (2c)and (2d).2010733
5580E18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314734-5010C30central air outlet onfascia - r+r . 1. At the bench, remove the anti-theft device on warning light fromthe centre air vent in the dashboard.2010734
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal3314911-5550D16third stop light - r+r . 1. Undo the bolts fixing the anti-theft remote control receiverto the rear parcel shelf.2. Remove the anti-theft device remote control receiver (2a) afterhaving disconnected the electrical connection (2b).2010735
5580E46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315190-7040B13load compartment/load platform right side trim -r r . 1. Undo the bolt (1a) and the nut (1b) fixing the anti-theft devicealarm/control unit.2. Disconnect the electrical connections (2a) and (2b), then removethe anti-theft device alarm/control unit (2c).2010736
5580E50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Press in the direction of the arrow and lower the volumetricsensor unit (1a), releasing it from the inner retainers (1b) and(1c). 2071341
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Release the retaining spring (1a) and remove the protective cover(1b).2. Disconnect the electrical connection from the lamp.3. Release the retaining spring (3a) and remove the lamp (3b) fromthe light cluster.767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010662
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Rotate the bulb holder (1a) in an anti-clockwise direction untilit is released from the light cluster (1b).2. Disconnect the electrical connection (2a) and extract the bulbholder.3. Separate the lamp from the bulb holder (press fit).767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010663
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve.Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen with an opaque surface, 10 metres away, whichcontains the following lines.1. V - V: vertical corresponding to the trace of the vehicle symmetryplane.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal corresponding to the height from the groundof the reference centres for the light clusters.4. AC - AC: horizontal 11 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2010664
5540B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2. Disconnect the electrical connection from the headlamp alignmentmotor.2010666
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the control unit fixing bolts.2071307
5540B44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010672
5540B46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010675
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010678
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7005A04 front side door waterguard protection - r r or replace with door panel removed Move the window to closed position.1. Disconnect the outer handle and dowel connection links from thecatch.2. Unscrew the outer bolts retaining the striker to the door.3. Disconnect the catch motor reduction unit electrical connectors.4. Disconnect cable (4a) from the inner door handle, take out controllink retaining spring (4b).5. Remove the catch assembly.2010796
English
