DescriptionThe car is equipped with extra bright tail-lights (rear fog lamps) located in the centre (on the boot) of the tail-light unit for use in cases of poor visibility.The rear fog lamps are activated by a button on the central console; the ideogram is lit up when the ignition is switched ON.A second LED in the activation button indicates that the rear foglamps have been turned on.The rear fog lamps are enabled when the dipped beams are on, or when the fog lamps are on.The control software is governed by the check device.Fog lamp operation is monitored by the exterior lighting check device.The following faults may occur:blown bulbbulb s.c. to earth or positiveincorrect bulb (5W bulb instead of 21W)a special light failure warning light comes on on the control panel whenever a fault is detected in the various circuits. This warning light comes on for about 6 seconds when the ignition key is turned to MAR, to indicate it is working properly, then it goes off.The rear fog lamp circuit is protected by two fuses for lights monitored by the check system.
Functional description The main beams are controlled by electronic Check device M45 , that receives control signals from the switches and controls the bulbs while also checking the various lines. The supply for the Check device M45 arrives directly from the battery (maxifuse CENTR of B5 ) to pins 1 and 6 of connector C, via fuse F11 of junction unit B1 . The supply controlled by the ignition (INT/A) arrives via fuse F1 of junction unit B1 at pin 9 of connector C: pin 7 of connector C is earhed. The device M45 receives as an input the signal for rear fog lamps switched on by the button located in unit H35 - pin 10 of connector A; this signal only arrives if the side lights are on. If, in addition to this signal, there is also the dipped beam headlamps on signal - pin 6 of connector B - or front fog lamps on signal - pin 2 of connector A, the device M45 then sends the supply to the rear fog lamps in the central rear lights clusters F35 (left) and F36 (right), from pin 10 and pin 4 respectively of connector E of M45 . At the same time, a signal is sent from pin 3 of connector B to the unit H35 to light up the LED near the button indicating the 'rear fog lamps on' function. The supply for this LED for H35 is controlled by the ignition (INT/A) via fuse F5 of junction unit B1 ; this line allows the control panel H35 to be lit up when controlled by the ignition (INT/A). The device M45 checks the efficiency of the bulbs and their connections: if faults are detected in the circuit, the 'lights fault' warning light on the instrument panel E50 , pin 7 of connector C, is lit from pin 6 of connector A, while pin 15 of connector A supplies an ignition-operated power supply to the panel through fuse F1 of the junction unit B1 .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal1. Undo the bolt (1b) and open the fuse access cover (1b).2. Remove the complete exterior light switch (2a) from its housingusing the tool (2b).767Exert pressure inside the exteriorlights switch to facilitate its removal.3. Disconnect the electrical connections (3a), (3b) and (3c) andremove the exterior lights switch (3d).2010651
5540A56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010652
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the fixing knob (1b) and open the access cover (1a) .2. Disconnect the electrical connection from the inner rear lightcluster.3. Undo the nuts (3a) and remove the inner rear light cluster (3b).2010654
5540A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Open the access cover after having undone the fixing knob.2. Release the retaining tabs (2a) and extract the bulb holder (2b)from its housing.3. Replace the rear fog lamps bulb (3a) or the reversing lightsbulb (3b) or the side lights bulb (3c).2010655
5540A80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010656
5540A94
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), remove the complete number plate light (1b).2. Disconnect the electrical connection and remove the number platelight.2010658
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in the stop position,disconnect the battery negative terminal.1. Release the gear lever boot from its seat on the console.2. Undo the handbrake lever boot stud from its seat on the consoleand release from the lever.3. Unscrew the console retaining bolts. 4. Disconnect the cigar lighter and ashtray light electrical connection.5. Remove the trim by withdrawing from the handbrake lever.2010988
7040L40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew the retaining bolt in the upper corner of the sill plate.2. Use tool (2a) to prise sill plate (2b) up from the underlyingretainers.2010989
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew bolts (1a) retaining the driver's side footrest and remove.2010991
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
