DescriptionThe rear window heater element, door mirror demister coils and the windscreen heater element absorb a considerable amount of energy. They must therefore be turned off once they have been working for a certain period of time.The system for demisting the rear window and door mirrors and heating the windscreen is controlled by a timer. The procedure is as follows.The system is turned on with:with the key in the ON positionactivation signal from the relevant button, located on the climate control system control panel.Coils are activated for 60 minutes, then the power supply is cut off.The power supply is also cut off under the following conditions:ignition in OFF position;deactivation signal from the relevant button;after the first 10 seconds of operation, if engine speed drops below 1000 rpm. .The led stays on as long as the back window heater element is activated.The control software is managed by the Check device located beside the junction unit (the climate control system panel houses only the control button and led, but does not affect the activation software in any way).The back window/door mirror demister and windscreen heater circuit is protected by a special fuse and controlled by a specific relay. These are located on the fuse and relay bracket on the right hand side of the luggage compartment.The door mirror and windowscreen coils are protected by another fuse located on the right hand side of the luggage compartment next to the fuse and relay described previously.
Functional description The heated rear window relay J55 controls the simultaneous switching on of the demisting function of the rear window P55 , the heated windscreen P56 and the external rearview mirrors P60 and P61 . (The control circuit of the heated rear window P55 passes through the power source/amplifier aerial P25 - 3309640SeeE3510RADIO ) The supply line to the latter is also protected by the mirror demister fuse B16 . The relay J55 is supplied by the direct line from the battery through the fuse B33 . An earth signal from the electronic Check device M45 - pin 10 of connector C - energizes the coil of relay J55 , so supply is sent to the resistors of P55 , P56 , P60 and P61 : this signal is enabled and suitably time-lagged by the device M45 . An ignition-operated power supply (INT/A) for the Check device M45 reaches pin 9 of connector C through fuse F1 of junction unit B1 : pin 7 of connector C is earthed. The device M45 gives enablement to the time-lagged switching on of the rear window when it receives the command from the on/off button - pin 11 of connector A - and at the same time the engine rpm signal is present - pin 8 of connector B, coming from the instrument panel E50 . The enablement takes place when the engine speed is above 1000 rpm. The button which switches on the heated rear window function is in the climate control panel H80 : the command is sent to the climate control unit M70 - pin 13 of connector C - from pin 9 through the serial line. The control unit M70 is supplied - to pin 11 of connector B - from the ignition-controlled line (INT/A) of relay R1 protected by fuse F9 of junction unit B1 : pin 8 of connector C is earthed. From pin 9 of connector B of M70 , the command is sent to the Check device M45 - pin 11 of connector A. With the function switched on, the Check device M45 sends back a signal - from pin 2 of connector B - to illuminate the led which indicates that the function is on; the signal reaches pin 11 of connector C of M70 and from there the controls H80 .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315012-7005E12corner cover of onefront side door, lh or rh r rWith the ignition key in the OFF position,disconnect the battery negative terminal.Take out the connector carrier and openit.1. Disconnect electric mirror wiring connectors (1a), (1b) and(1c). 2. Remove bolt cover panel (2a) and uncrew the bolts (2b) securingthe mirror to the door.3. Withdraw the wiring and remove the mirror.2010797
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use tool (1a) to prise out reflector (1b).1. Disconnect the electrical connections from the reflector andthen remove.2010798
7005R36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315037-7005R35door mirror reflector- r r1. Unscrew the motor retaining bolt.2. Disconnect the electrical connections shown.3. Remove the positioning motor.2010799
7005R37
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315037-7005R35door mirror reflector- r r3315038-7005R36door mirror motor - r r1. Unscrew the bolts retaining the cover to the mount.2. Unscrew the bolts retaining the motor mount to the cover.3. Cut the electrical wiring retaining strip and prise the outdoortemperature sensor out of the cover.4. Remove the rear view mirror cover.2010800
7005R40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Take the control switch unit out of the handle by undoing theretaining clip.2. Disconnect the electrical connectors.3. Remove the control switch unit.2010801
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314810-5050B34windscreen wiper arm/s complete with blade - r+r . 3315282-7055A18Windscreen base TRIM - R.R. . 1. Disconnect the electrical connection for the intake/recirculationair flap actuator.2. Undo the bolts (2a) and loosen the bolt (2b) for the recirculation/intakeair flap actuator using the tools (2c) and (2d).3. Disconnect the linkage (3a), rotate the recirculation/intakeair flap actuator (3b), completely undo the remaining bolt and removeit.2010575
5040D70
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314729-5010B52ducts (one), lh or rh,on air distribution unit for air duct beneath facia r r with faciaremoved . 1. Disconnect the electrical connection for the distribution airflap actuator.2. Undo the fixing bolts and move the distribution air flap actuatoraside.3. Undo the bolts (3a) and remove the actuator mounting bracket(3b).4. Release the wiring and remove the distribution air flap actuator.2010576
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314767-5040A10Air conditioning refrigerant CIRCUIT - Draining andRefilling . 1. Disconnect the electrical connection for the air conditioningsystem multi-stage pressure switch.2. Undo and remove the air conditioning system multi-stage pressureswitch.2010547
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Undo the wing bolts and removethe boot left side trim. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connections forthe loudspeakers' amplifier.1. Undo the nuts and move aside the on-board navigator componentsmounting as far as necessary.Disconnect the electrical connection fromthe navigation system CD player/changer.Disconnect the electrical connections ofthe audio CD player/changer.2. Remove the complete on-board navigator components mounting.2010738
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
