DescriptionAn electronic management system supervises and governs all engine parameters. It optimises performance and fuel consumption by responding in real time to different service conditions.The system is managed by a single control unit that controls the twin spark ignition (static and lost spark), and the injection (phased).The system uses signals received from numerous sensors to control actuators. It is connected to the following systems:fuel supply;air supply system;accelerator pedal;engine cooling;exhaust with catalytic converter;fuel vapour recirculation.On this version, the engine is fitted with a throttle body controlled electronically by the control unit. The opening of the throttle is calculated in accordance with a specific logic within the engine management control unit; This dispenses with the need for a mechanical connection between the accelerator pedal and the throttle body. For more details, 3308466see DESCRIPTION AND OPERATION:1056PETROL INJECTION SYSTEMSupply lines to the control unit and the various system components (sensors and actuators) are protected by a special maxifuse and another protects the steering wheel fuses, located with the relays in a service tank (behind the engine bulkhead).
Functional description The engine control unit M10 monitors and controls the entire electronic ignition and injection system. The control unit is supplied directly by the battery via a line protected by maxifuse CENTR of B5 at pin 4 of connector B of M10 via the line protected by fuse F20 of junction unit B1.The main fuel injection relay J10 controls the entire system: it is supplied directly by the battery via the line of maxifuse B80; it is energized by an ignition-dependent signal (INT/A) by the line protected by fuse F16 of junction unit B1; the main relay J10 thuse sends a supply:to pin 2 of connector A of control unit M10 ;to injectors N70 ;to the coils A30 ;to timing sensor K47 , via a line protected by fuse B40.to air flow meter K41 , via a line protected by fuse B40 ;to fuel vapour recovery solenoid L10 , via a line protected by fuse B40 ;to the Lambda sensor heater K40 , via the line protected by fuse B40 ; The ignition-operated power supply (INT/A) also supplies fuel pump J15 , which is excited by a control signal (earth) from pin 29 of connector C of control unit M10 . This supplies power - via fuse F3 of junction unit B1 to fuel pump N40 , which is earthed through inertia switch I50 , which cuts off the circuit in the case of impact to prevent the danger of fuel flowing out. Pins 3, 7 and 8 of connector A of control unit M10 are earthed and used as references: the first two for the ignition and the third for the injectors. Pin 8 of connector F is also earthed. The engine control unit M10 receives signals from the various sensors in order to monitor all engine service conditions. Rpm sensor K46 supplies information on engine speed via a frequency signal sent to pins 37 and 38 of connector E of control unit M10 . Timing sensor K47 receives a reference earth from pin 39 of connector E of control unit M10 and sends back a frequency signal corresponding to the timing to pin 40 of the same connector. Engine temperature sender unit K36 receives a reference earth from pin 28 of connector E of control unit M10 and supplies a signal proportional to the coolant temperature to pin 29 of control unit connector E. The same sender unit also supplies information to the temperature gauge and warning light ( 3309717SeeE4010INSTRUMENT PANEL ). Hot lambda probe K40 provides control unit M10 with information on the correct composition of the air-fuel mixture. The signal is sent to pin 23 of connector C of the control unit, while pin 31 provides a reference earth signal. Probe K40 is heated by a resistor in order to ensure it works efficiently even when cold; the resistor is supplied by the relay J10 and receives the heating signal from pin 5 of connector A of M10 . Knock sensors K50 and K51 provide information on knock status via frequency signals sent to pins 42 and 44 respectively of control unit connector E. An earth signal is sent from pins 41 and 43 of connector E of M10 respectively. Air flow meter K41 (supplied from relay J10 ) receives a reference voltage from pin 46 of control unit connector E and sends to pin 47 of the same connector a signal proportional to air flow. K41 also contains an air temperature sensor: the sensor reference earth is supplied by pin 48 of connector E of M10, while pin 45 of connector E receives an air temperature signal. Accelerator pedal K55 is fitted with two built-in potentiometers (a main one and a safety back-up). The first receives power and earth from pins 22 and 23 respectively of connector C of M10 and sends a corresponding signal to pin 24 of the same connector. The second receives power and earth from pins 27 and 26 respectively of connector C of M10 and sends a corresponding signal to pin 25 of connector C. Pin 14 of connector D of M10 receives a signal from brake light switch I30 , ignition-operated (INT/A) through a line protected by fuse F1 in junction unit B1 ( 3309181SeeE2021BRAKE LIGHTS ). Pin 19 of connector D of M10 receives an earth signal from clutch pedal switch I31 . Injectors N70 receive a power supply to enable opening from main relay J10 . The engine management unit sends commands to the injectors from pins 25, 13, 1, 26, 14 and 2 of the connector, for cylinders 1, 2, 3, 4, 5 and 6 respectively. Control unit M10 also controls coils A30 via control signals for the coil primary windings, while the secondary winding sends a pulse to the spark plugs: pins 20, 6, 17, 13, 19 and 5 of connector F control ignition coils 1, 2, 3, 4, 5 and 6 respectively. The primary windings of the coils A30 receive a signal to enable opening from main relay J10 . Throttle body actuator N75 is fitted with two built-in potentiometers connected in parallel: they control throttle opening via a stepper motor. The motor receives information from pins 1 and 2 of connector F of M10 . Pin 33 of connector E sends a power supply to both potentiometers, pin 32 of connector E supplies an earth signal to the potentiometers, while pins 31 and 34 of the same connector receive signals from throttle body actuator N75 . Fuel vapour recovery solenoid L10 allows fuel vapours to pass through to the engine intake where they join the mixture entering the combustion chamber. Valve L10 , supplied by main relay J10 (via fuse B40 ), is opened by the control unit when the engine is under load via a duty-cycle signal from pin 21 of connector C of M10 . The control unit M10 is connected to the ALFA ROMEO CODE control unit M20 via a specific serial line from pin 39 of connector C; in this way if the ALFA ROMEO CODE unit does not detect a correct code, it does not issue enablement and the engine is not started.( 3309948SeeE7010CODE ). The control unit is equipped with a self-test system that may be used by connecting the unit to connector R10 : this receives indirect signals from control unit M10 via a serial line from control unit M20 described above.(pin 39 of connector C). The self-diagnostic system also generates a signal - from pin 21 of connector F - to the injection failure warning light on instrument panel E50 . This signal leaves control unit M10 , while pin 15 of connector A of E50 supplies an ignition-operated power supply (INT/A) from a line protected by fuse F1 of junction unit B1 . The speedometer signal (car speed) reaches pin 13 of connector D of control unit M10 ( 3309717SeeE4010INSTRUMENT PANEL ); the signal is generated by the ABS control unit M50 . Control unit M10 sends the instrument - via pin 38 of connector C - a signal proportional to engine rpm (see 3309717SeeE4010INSTRUMENT PANEL ). Control unit M10 is connected to the air conditioning system via pins 4 and 21 of connector E. This allows engine idling speed to be adjusted to increased engine load whenever the compressor is activated, or to turn off the compressor in the case of high speeds or high engine loads ( 3309931SeeE6021COMPRESSOR ENGAGEMENT ). The control unit also controls the engine cooling system: pin 6 of connector A, 3 of connector D and 15, 17 of connector E control activation of the relevant fan ( 3309782SeeE5020ENGINE COOLING ). Control unit M10 is connected to the electronic automatic transmission (EAT) via pins 5 and 17 of connector D ( 3310059SeeE7050AUTOMATIC TRANSMISSION ). Pins 11 and 12 of connector D of control unit M10 are connected to the ABS/ASR control unit via CAN line ( 3310008SeeE7021ASR / TCS ). Pins 20, 21, 22, 23, 24 of connector D and pin 10 of connector E of control unit M10 are connected to Cruise Control; ( 3309870SeeE5060CRUISE CONTROL ). Pin 28 of connector C and pins 23 and 24 of connector E of control unit M10 are connected to the electronic throttle opening system ( 3309896SeeE5065SPORT THROTTLE RESPONSE ). Some versions are fitted with supplementary connector R51 for connection to the control unit. This is located in the engine bay. 767This connection is used solely at the Production Plant and SHOULD UNDER NO CIRCUMSTANCES be used during servicing.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the high tension leads from the ignition coil.2. Disconnect the electrical connection from the ignition coil.3. Undo the bolts (3a) and remove the ignition coil (3b).2010599
5510C14
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . 1. Disconnect the electrical connections from the ignition coils.2. Disconnect the electrical connection for the air conditioningcompressor electro-magnet coupling.3. Disconnect the earth lead from the ignition coils mounting bracket.Release the electrical wiring from thebands on the tappet cover and move it aside.2010600
5510C16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314293-1016A42left hand cylinder head ignition coil cover - r+r . 1. Disconnect the electrical connections from the ignition coils.1. Undo the bolts (1a) and remove the electrical wiring securingbrackets (1b).Move the electrical wiring to the side.2010607
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the lift. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection for the rpm and timing sensor.2010611
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the air supply hose from the air chamber.2. Disconnect the electrical connection from the engine coolanttemperature sensor.3. Undo and remove the engine coolant temperature sensor.2008717
1060G16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the excess pressuresensor.2. Undo the bolt (2a), remove the excess pressure sensor (2b).2008718
1060G18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the fuel temperaturesensor.2. Undo and remove the fuel temperature sensor from the fuel returnmanifold pipe.2008719
1060G20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the lift. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315302-7055B54under-engine guard - r r . 1. Disconnect the condensation oil return pipe from the separatorfrom the sump.2. Disconnect the electrical connection for the engine rpm and timingsensor.3. Undo the bolt (3a) and remove the engine timing and rpm sensor(3b).2008720
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 3314409-1016A10sound-proofing cover- r + r . 1. Disconnect the electrical connection from the fuel pressure sensoron the fuel manifold.2. Undo and remove the fuel pressure sensor on the fuel manifold.2070776
1060G30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Release the fuel supply and return pipes from the band.2008722
1060G38
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connection fromthe switch on the brake pedal.Rotate and remove the switch on the brakepedal.
1060G42
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connection fromthe switch on the clutch pedal.Rotate and remove the switch on the clutchpedal.
1060G50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Loosen band (1a) and disconnect the air delivery sleeve fromheat exchanger to intake manifold (1b), throttle body connectorside.2. Loosen the band (2a) and disconnect the vacuum pipe (2b) fromthe vacuum unit.2008725
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Loosen band (1a) and disconnect the air delivery sleeve fromheat exchanger to intake manifold (1b), throttle body connectorside.2008729
1060G70
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Disconnect the electrical connection from the solenoid on thevacuum tank.2008731
1060G72
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Disconnect the electrical connection from the solenoid on thevacuum tank.2. Disconnect the vacuum pipes from the solenoid on the vacuum tank.3. Undo the upper bolt (3a), loosen the lower bolt (3b), then releaseand remove the solenoid valve on the vacuum reservoir (3c), completewith lower pad. Recover the upper bolt pad.2008735
1060G80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Remove the buttons (1a) using the tool (1b) and remove the protection(1c).2. Open the two protective covers (2a) and undo the nuts (2b) underneathfixing the control unit cover.3. Undo the bolts (3a) and remove the control unit cover (3b).2008736
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Remove the caps (1a) and undo the bolts (1b) fixing the thirdbrake light to the rear parcel shelf.2. Disconnect the electrical connection (2a) and remove the thirdbrake light (2b).2010698
5550D17
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314911-5550D16third stop light - r+r . 1. Undo the bolts (1a) and remove the bulb holder (1b).2010699
5550D18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315223-7040L20tunnel trim - r r1. Undo the nut (1a) and disconnect the earth lead (1b).2. Disconnect the electrical connection from the handbrake warninglight switch.3. Undo the nut (3a) and remove the handbrake warning light switch(3b).2010701
<anchor>1</anchor><span>Refitting</span><icon><imageid>21</imageid></icon>0Removing20.767The fuel tank is supplied by theParts Dept. together with the multifunction valves (which cannotbe dismantled) and the immersed pump assembly complete with gauge.Therefore if the tank has to be replaced it is not possible to reuse theimmsered pump assembly complete with gauge removed, but a new pre-assembledunit consisting of a tank - pump - multifunction valves suppliedby the Parts Dept. must be fitted.Move the fuel tank closer to its housingusing the hydraulic jack and connect the supply pipes to the fuel vapourseparator.Refit the fuel tank in its seating andsecure with its bolts.Remove the hydraulic jack from under thefuel tank.1. Replace the rear suspension crossmeber (1a) in its housing usingthe hydraulic jack (1b) and fix it tightening the bolts (1c) tothe recommended torque.Remove the hydraulic jack from under thecrossmember.2007293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the lift.3315188-7040B10load platform (luggage platform) trim - r+r . 3314100-1040A70submerged pump assembly complete with level guagecontrol - r + r . Drain the fuel from the tank using suitableequipment.3314704-4450B11WHEEL (one) rear - R.R. (right) Undo the bolts and remove the rear partof the right rear wheel arch liner.1. Disconnect the connecting pipes to the valves on the tank fromthe fuel vapour separator.2. Disconnect the rapid attachment for the fuel vapour supply pipeto the canister.3. Undo the bolts fixing the fuel filler pipe to the bodyshell.4. Loosen the band fixing the fuel filler pipe to the hose.2007299
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the access flap to the fuel fillerpipe cap.Undo and remove the fuel filler pipe cap.
1040A70
769
1040A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7045A10 l/h or r/h front seat (one) - r+r . 1. Cut the floor carpet along the marked line.2. Undo the bolts fixing the inertia switch to the bodyshell.3. Disconnect the electrical connection (3a) and remove the inertiaswitch (3b).2007309
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . 3314111-1048A48throttle heater sleeve - r r . 1. Disconnect the electrical connection from the butterfly casingintegrated with the M.D.S.2. Disconnect the electrical connections (2a) and (2b) from theinjection/ignition control unit and the earth lead (2c) from thebutterfly casing integrated with the M.D.S.3. Disconnect the accelerator cable from the butterfly casing integratedwith the M.D.S.4. Disconnect the injection/ignition wiring from the mounting bracket.5. Undo the bolts (5a) and remove the butterfly casing integratedwith the M.D.S. (5b) complete with the injection/ignition controlunit (5c).2007326
1056B21
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3315197-7040D14engine bay rear sidecover (one) lh or rh - r r (Right side). 1. Loosen the band (1a) and disconnect the oil vapour recirculationpipe (1b) from the corrugated hose.2. Loosen the bands (2a) and remove the hose between resonator andthrottle body (2b), complete with resonator (2c).2007327
1056B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . 1. Disconnect the electrical connection from the phase transformerelectro-magnet.2. Undo the bolts (2a) and remove the phase transformer electro-magnet(2b).2007334
1056B50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314110-1048A28vacuum air circuit resonator pipe - r+r1. Disconnect the electrical connection from the engine coolanttemperature sensor.2. Undo and remove the engine coolant temperature sensor.2007335
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3314048-1016A40ignition coil cover on cylinder head- r+r . Discharge the fuel supply pressure (seeGroup 10 Warnings).1. Disconnect the rapid attachment for the fuel supply pipe.2. Disconnect the electrical connections from the injectors (2a)and the electrical connection from the phase transformer electro-magnet(2b).3. Undo the two bolts (3a) and remove the single fuel manifold pipe(3b) complete with injectors (3c).2007337
1056B68
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the clips (1a) and remove the injectors (1b) from thesingle fuel manifold pipe.2. Remove the seals from the injectors.2007338
Make sure that the ignition key is in theOFF position. Check that: the air conditioning is switchedoff, the accelerator pedal is never pressed and the accelerator cableis correctly positioned (refer to op. 33141321068A30accelerator control cable - r + r ). Connect the tool to the diagnostic socketand place the knob in position 3.Connect the Examiner diagnostic equipment.Connect the Examiner diagnostic equipment.Using the Examiner, enter the "ControlUnit Test" ambient.Place the ignition key in the ON position.Using the Examiner, enter the "ActiveDiagnosis" ambient, then select "Reset self-adjustmentparameters" and "Idle actuator".Using the Examiner, press "Carry outactive diagnosis".Place the ignition key in the OFF positionand wait for 30 seconds.Place the ignition key in the ON positionand wait for 30 seconds.Using the Examiner, re-establish the dialoguewith the engine control system.Using the Examiner, enter the "Parameters"ambient and select the following tests from the menu - "Idle recognitiontest - carried out" and "Idle recognition signals - synchronized".767If at least one of the parametersdoes not conform, place the ignition key in the OFF position andrepeat the procedure. If this non conformity persists, check thatthe diagnostic cable is correctly connected and check the operationof the instrument.Place the ignition key in the OFF positionand wait for 30 seconds.Start up the engine without acting on theaccelerator pedal.Disconnect the diagnostic equipment.Test the vehicle by driving for severalkilometres then, with the engine warmed up, check that it is idlingcorrectly.
1056B82
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Release and disconnect the electrical connections (1a) and (1b)from the injection/ignition system control unit.2. Undo the nuts (2a) and remove the injection/ignition controlunit (2b).2007339
1056B82
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3315197-7040D14engine bay rear sidecover (one) lh or rh - r r (Right side). 1. Loosen the band (1a) and disconnect the oil vapour recirculationpipe (1b) from the corrugated hose.2. Loosen the bands (2a) and remove the hose between resonator andthrottle body (2b), complete with resonator (2c).2007340
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the intake air temperaturesensor.2. Undo and remove the intake air temperature sensor.2007791
1056B62
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Discharge the fuel pressure (see GR 10- WARNINGS).1. Disconnect the electrical connections from the injectors.2007793
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the altitude corrector. 2. Undo the attachments and remove the altitude corrector.2007796
1056B79
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the buttons (1a) using the tool (1b) and remove the protection(1c).2. Open the two protective covers (2a) and undo the nuts (2b) underneathfixing the control unit cover.3. Undo the bolts (3a) and remove the control unit cover (3b).2007797
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (rightand left). 3315198-7040D30engine bay front beam cover - r r . 1. Disconnect the electrical connections from the engine radiatorfan resistance.2. Disconnect the electrical connection from the engine coolingfan.Release the electrical wiring from thesecuring bands.3. Undo the bolts (3a) and remove the engine cooling fan (3b).2007448
1088E20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (rightand left). 3315198-7040D30engine bay front beam cover - r r . 1. Disconnect the electrical connections (1a) and (1b) from theresistance for the engine cooling fan.2. Undo the bolts (1a) and remove the resistance for the enginecooling fan (1b).2007449
1088E11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (rightand left). 3315198-7040D30engine bay front beam cover - r r . 1. Disconnect the electrical connections for the engine radiatorfan resistances (1a) and (1b).2. Disconnect the electrical connections from the engine coolingfans (2a) and (2b).3. Release the electrical wiring from the securing bands.2008921
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the lift. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection for the Lambda sensor andrelease the electrical wiring from the bands on the modular inletmanifold.2007407
1080B62
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp.Position a hydraulic jack under the catalyticconverter.1. Undo the bolts fixing the catalytic converter to the exhaustpipe attached to the manifold.2. Tighten the bolts fixing the catalytic converter to the intermediateexhaust silencer.3. Remove the catalytic converter.4. Remove the seals.2007409
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp. Ensure that the ignition key is in OFFposition, then disconnect the negative terminal (-) from the battery( 3314861-5530B10battery - r+r ). 1. Disconnect the electrical connection for the rear Lambda sensorfor the catalytic converter.2007419
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a ramp. Proceed with the removal 3315302-7055B54under-engine guard -r r . 1. Undo the bolt (1a) and remove the collar (1b) connecting theexhaust pipes between preconverters and catalytic converter.2008349
1080B66
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a ramp.1. Open the cover of the electrical connection box.2. Remove the connections and disconnect the electrical connectionfor the left rear Lambda sensor for the catalytic converter.Release the electrical wiring for the leftrear Lambda sensor for the catalytic converter from the fastenings inthe engine bay.2008377
1080B97
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Place the vehicle on a ramp.1. Open the cover of the electrical connection box. 2. Remove the connections and disconnect the electrical connectionfor the right rear Lambda sensor for the catalytic converter. Release the electrical wiring for the rightrear Lambda sensor for the catalytic converter from the fastenings inthe engine bay. 2008380
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Remove the rubber accelerator pedal cover.
1068A14
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the end of the accelerator cable (1a) from the acceleratorpedal (1b).2. Remove the clip (2a), undo the bolts (2b) and remove the acceleratorpedal (2c).2007347
1068A30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the end of the accelerator cable (1a) from the acceleratorpedal (1b).2007351
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Remove the passenger side carpet.1. Undo bolts (1a) and remove passenger side footrest (1b).2008240
1068A53
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working from the right side of the passenger compartment, undothe upper bolts retaining the pedal unit to the bodyshell.2. Loosen the nuts retaining the pedal unit to the bodyshell.2008252
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the lift.3314704-4450B11WHEEL (one) rear - R.R. (right) Undo the bolts and remove the rear partof the right rear wheel arch liner.1. Undo the bolts fixing the fuel filler pipe to the bodyshell.2007422
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314048-1016A40ignition coil cover on cylinder head- r+r . 3314111-1048A48throttle heater sleeve - r r . 1. Disconnect the electrical connection from the fuel vapour cut-outsolenoid valve from the filter.2. Undo the bolts (2a), disconnect the pipes (2b) and remove thefuel vapour cut out solenoid valve from the filter (2c).2007426
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on the ramp. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315302-7055B54under-engine guard - r r . 1. Disconnect the electrical connection from the supercharging pressuresolenoid valve.2. Undo the nut securing the supercharging pressure solenoid valve.3. Disconnect the pipes (3a) and remove the supercharging pressuresolenoid valve (3b).2007805
1064B42
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Ensure that the ignition key is in OFFposition, then disconnect the battery negative terminal ( 3314861-5530B10battery - r+r ). Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Loosen the band (1a) and disconnect the oil vapour recirculationpipe (1b) from the tappet cover.2008770
1064B50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Disconnect the turbocharger vane position actuator solenoid inletpipe, vacuum reservoir side.2008772
1064B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Proceed with the removal 3314409-1016A10sound-proofing cover- r + r . 1. Disconnect the pipe from the solenoid valve to the turbochargervane position actuator, solenoid valve side.2. Release the pipe from the solenoid valve to the turbochargervane position actuator from the fastenings.2008775
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the nuts (2a) and remove the electronic key anti-theft controlunit (2b) after having disconnected the electrical connections (2c)and (2d).2010733
5580E18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314734-5010C30central air outlet onfascia - r+r . 1. At the bench, remove the anti-theft device on warning light fromthe centre air vent in the dashboard.2010734
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal3314911-5550D16third stop light - r+r . 1. Undo the bolts fixing the anti-theft remote control receiverto the rear parcel shelf.2. Remove the anti-theft device remote control receiver (2a) afterhaving disconnected the electrical connection (2b).2010735
5580E46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315190-7040B13load compartment/load platform right side trim -r r . 1. Undo the bolt (1a) and the nut (1b) fixing the anti-theft devicealarm/control unit.2. Disconnect the electrical connections (2a) and (2b), then removethe anti-theft device alarm/control unit (2c).2010736
5580E50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Press in the direction of the arrow and lower the volumetricsensor unit (1a), releasing it from the inner retainers (1b) and(1c). 2071341
abs check/adjustment devices
3340A12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (left). 3315197-7040D14engine bay rear side cover (one) lh or rh - r r (left). Remove the cap with built-in brake fluidlevel switch and drain the brake/clutch fluid from the reservoir usinga suitable syringe.1. Disconnect the comb from the A.B.S. hydraulic and electroniccontrol unit.2. Release the A.B.S. pipes from their clip.3. Disconnect the pipes from the A.B.S. hydraulic and electroniccontrol unit and move them aside.2009904
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on thelift. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r (right) 3315197-7040D14engine bay rear side cover (one) lh or rh - r r (right) 1. Release the front right wheel speed sensor wiring from its clamp.2. Disconnect the electrical connection for the front right wheelspeed sensor.3. Release the rubber cable pass for the front right wheel speedsensor wiring from the bodywork.2009919
3340A35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on thelift.3314864-5530B54battery cover - r+r . 3314861-5530B10battery - r+r . 3314863-5530B52Battery DRIP TRAY/SUPPORT - R.R. . 1. Disconnect the electrical connection (1a) for the rear rightwheel speed sensor and release the wiring from the clip (1b).2. Release the rubber cable pass from the rear left wheel speedsensor from the bodywork.2009921
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Release the retaining spring (1a) and remove the protective cover(1b).2. Disconnect the electrical connection from the lamp.3. Release the retaining spring (3a) and remove the lamp (3b) fromthe light cluster.767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010662
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Rotate the bulb holder (1a) in an anti-clockwise direction untilit is released from the light cluster (1b).2. Disconnect the electrical connection (2a) and extract the bulbholder.3. Separate the lamp from the bulb holder (press fit).767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010663
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve.Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen with an opaque surface, 10 metres away, whichcontains the following lines.1. V - V: vertical corresponding to the trace of the vehicle symmetryplane.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal corresponding to the height from the groundof the reference centres for the light clusters.4. AC - AC: horizontal 11 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2010664
5540B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2. Disconnect the electrical connection from the headlamp alignmentmotor.2010666
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the control unit fixing bolts.2071307
5540B44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010672
5540B46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010675
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010678
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314362-1060F36lines to injectors - r r . 1. Disconnect the electrical connections from the injectors, thenmove the electrical wiring after having released it from the bands.2008706
1060F20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Undo the bolts and move the fuel returnmanifold pipe away from the air chamber.1. Undo the connector for the pipe from the pressure pump to thefuel manifold, manifold side, using a suitable spanner2. Undo the connector for the pipe from the pressure pump to thefuel manifold, pump side, using a suitable spanner.3. Remove the pipe from the pressure pump to the fuel manifold.767Fit a new high pressure pipe fromthe pressure pump to the fuel manifold upon reassembly. 2008708
1060F30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314362-1060F36lines to injectors - r r . 1. Disconnect the electrical connection from the fuel pressure sensor.2. Undo the connector for the pipe from the pressure pump to thefuel manifold, manifold side, using a suitable spanner3. Undo the connector for the pipe from the pressure pump to thefuel manifold, pump side, using a suitable spanner.4. Remove the pipe from the pressure pump to the fuel manifold.767Fit a new high pressure pipe fromthe pressure pump to the fuel manifold upon reassembly. 5. Undo the nuts (5a) and remove the single fuel manifold pipe (5b).2008710
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the nuts (1a) and move the fuel filter (1b) away from theair capacity body.2. Undo the nuts (2a) and remove the oil vapour separator (2b) awayfrom the air chamber.3. Undo the bolts (3a) and move the fuel return manifold pipe (3b)aside.4. Undo the connectors for the pipes from the fuel manifold to theinjectors, injector side, using a suitable spanner.5. Undo the connectors for the pipes from the fuel manifold to theinjectors, injector side, using a suitable spanner.6. Remove all the pipes from the fuel manifold to the injectors.767Fit new pipes from fuel manifoldto injectors upon reassembly.2008712
1060F50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the fuel temperaturesensor.2.Disconnect the following from thefuel return manifold pipe:the fuel return pipe for lubricating the injectors (2a),the fuel return pipe from the pressure pump (2b),the fuel return pipe to the tank (2c),the fuel return pipe from the filter (2d).2008714
1060F52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the pipe from the injectorsto the fuel recovery manifold, manifold side.Remove the springs on the injectors andremove the pipe from the injectors to the fuel recovery manifold.
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
