DescriptionThe boot is opened by means of a button located in the glove compartment or by the key: the key is inserted into the boot lock and turned to operate an electric motor.The boot opening circuit is enabled for operation only when the car is at a standstill. It is protected by a fuse located in the luggage compartment.Fuel flap opening is controlled by a button on the tunnel near the gearlever.The fuel flap opening circuit is enabled for operation only when the car is at a standstill. It is protected by a fuse located in the luggage compartment.
Functional description Boot opening is controlled by the specific central boot opening switch H33 located in the glove compartment or by the key inserted in the rear lock (boot opening switch H71 ). When the car is stationary if the button H33 is pressed it energizes the boot opening relay J56 . The enablement signal comes from pin 9 of connector B of the instrument panel E50 , whose internal software enables this function when the speedometer signal - coming from the ABS control unit - is less than 2 km/h. The boot opening switch H71 energizes the relay J56 without any enablement. The relay J56 is supplied directly from the battery, through the fuse line B62 , and controls the boot lock motor N57 . Fuel flap opening is controlled by the specific switch located among the controls on the tunnel H36 . When the engine is not running, if the button H36 is pressed it energizes the fuel flap opening relay J57 ; the enablement signal arrives from terminal D+ of the alternator A10 : it is the same signal which lights up the recharging warning light in the instrument panel ( 3309762SeeE5010STARTING AND RECHARING ). The relay J57 is supplied directly from the battery, through the fuse line B61 , and it controls the fuel flap locking motor N58 .
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Lift the boot lid.1. Loosen hinge bolts (1a) and adjust the boot lid position.Arrows(1b) indicate permitted movements.Tighten the hinge retaining bolts to thespecified torque.2. Adjust the buffer blocks if necessary.2010856
7025B14
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315123-7025B18boot lid lining - r+r3315125-7025B26l/h or r/h boot lid lift device (one) - r+rOpen the luggage compartment lid.1. Disconnect electrical connectors (1a), (1b), (1c) and (1d).2. Release the wiring from the clips that secure it to the bootlid.3. Prise up wiring duct protection (3a) from the boot lid and withdrawwiring (3b).4. Unscrew the hinge fastenings and remove the boot lid with theaid of a second operator.2010858
7025B18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the boot lid.1. Use tool (1a) to remove retaining studs (1b). 2. Remove the sound-deadening trim.2010859
7025B22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Unscrew bolts retaining the bracket to the body.2. Remove the hinge by releasing from the sealant.2010860
7025B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the boot lid.1. Undo the retaining clips.2. Slightly lift the heads press-fitted to the boot hinge.3. Remove the raising device.2010861
7025B38
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315123-7025B18boot lid lining - r+r3315127-7025B41boot lid lock1. Disconnect the catch dowel control link from the dowel spring.2. Unscrew the catch retaining bolts. 3. Remove the catch from its seat to gain access to link (3) andthen disconnect.4. Disconnect electrical connection (4a), then remove catch (4b).2010862
7025B41
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the boot lid.1. Use tool (1a) to prise out plastic guard (1b) from the catchand remove.2010863
7025B46
<anchor>1</anchor><span>Refitting</span><icon><imageid>21</imageid></icon>0Removing20Check that the lock barrelis undamaged.Fit the retaining spring into its seat.Fit the lock barrel into its seat untilthe groove engages with the retaining clips.Test that the barrel works properly andthat the catch control mechanism action is correct. Complete op. 33151237025B18boot lid lining - r+r
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315123-7025B18boot lid lining - r+r1. Disconnect the ends of link (1a) from connections (1b) on thebarrel and catch, then remove the link.2010865
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.3315123-7025B18boot lid lining - r+r3315127-7025B41boot lid lock3315126-7025B38boot lid lock - r+r1. Unscrew the lock motor retaining nuts.2. Disconnect motor actuator electrical connection (2a) and removemotor (2b).2010870
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the front directionindicator bulb.2. Rotate the bulb holder in an anti-clockwise direction and extractit.3. Remove the bulb for the front direction indicator from the bulbholder (bayonet fitting).2010694
5550C22
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 767Protect the panel surroundingthe side repeater using paper tape to prevent the paintwork from beingdamaged.1. Remove the side repeater (1a) using the tool (1b).2. Disconnect the electrical connection from the side repeater andremove it.3. Rotate the bulb holder (3a) in an anti-clockwise direction andextract it, then remove the bulb (3b) which is a press fit.2010695
5550C40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the bolts (1a) and remove the right and left trims (1b).2010696
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the nuts (2a) and remove the electronic key anti-theft controlunit (2b) after having disconnected the electrical connections (2c)and (2d).2010733
5580E18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314734-5010C30central air outlet onfascia - r+r . 1. At the bench, remove the anti-theft device on warning light fromthe centre air vent in the dashboard.2010734
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal3314911-5550D16third stop light - r+r . 1. Undo the bolts fixing the anti-theft remote control receiverto the rear parcel shelf.2. Remove the anti-theft device remote control receiver (2a) afterhaving disconnected the electrical connection (2b).2010735
5580E46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315190-7040B13load compartment/load platform right side trim -r r . 1. Undo the bolt (1a) and the nut (1b) fixing the anti-theft devicealarm/control unit.2. Disconnect the electrical connections (2a) and (2b), then removethe anti-theft device alarm/control unit (2c).2010736
5580E50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Press in the direction of the arrow and lower the volumetricsensor unit (1a), releasing it from the inner retainers (1b) and(1c). 2071341
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314706-4450B13rear wheels(2) r r3315301-7055B43REAR WHEEL ARCH liner (one), left or right - R.R.1. Open the fuel flap and remove the filler cap.2. Remove fuel filler fitting rubber protection (2a) and unscrewboth nuts (2b) securing the flap hinge to the body.3. Remove the flap and hinge from the outside by releasing the retainingpins.2010872
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
