DescriptionThe vehicle is prepared for fitting a cellular telephone.This preparation consists of a specific connection, located inside the tunnel cover by the centre armrest between the front seats which provides the supply for the telephone and the connection for the hands free function.The predisposition comprises the following parts:specific aerial, located at the rear of the roof (with dual function GSM and GPS);a hands-free speaker, located in the passenger door. It is the same loudspeaker as for the radio, with a double connection;predisposition for a microphone in the area of the front courtesy light (2.0 TB 6M and 3.0 V6 only);connection for the supply and recharging of the cellular telephone, located in the central armrest;cables for supplying and connecting the components.The mobile phone connection has two power supplies; one direct from the battery and one ignition operated.The above lines are protected by two fuses in the junction unit.
Functional description The connection D75 receives the direct supply (pin 1) from the battery via the line of fuse F18 of the junction unit B1 and the maxifuse B5 . Receives the ignition-dependent supply (INT/A) (pin 5) via the line of fuse F5 of the junction unit B1 . Pin 3 of connection D75 is earthed at C34 , while pins 6 and 7 supply the signal to the loudspeaker P46 , connector B, while connector A is for the car radio (see E3510 - RADIO). Pins 4 and 8 of connection D75 represent the preparation for the microphone P26 (hands free function). Only the 2.0 TB 6M and 3.0 V6 versions have the preparation at the front courtesy light fitted as standard; the other versions have the preparation up to coupling D42 (Dashboard/Courtesy lights coupling). The MUTE signal for decreasing the volume during a telephone call is sent to the radio system via pin 2 for connection D75.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Undo the wing bolts and removethe boot left side trim. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connections forthe loudspeakers' amplifier.1. Undo the nuts and move aside the on-board navigator componentsmounting as far as necessary.Disconnect the electrical connection fromthe navigation system CD player/changer.Disconnect the electrical connections ofthe audio CD player/changer.2. Remove the complete on-board navigator components mounting.2010738
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis in the OFF position, then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315271-7050A20one-piece rear seat cushion - r r . 3315270-7050A19rear seat squab - r r . - 7050A42 rear squab catch device (one) - r+r (left). 1. Disconnect the electrical connections from the radio aerial controlunit in the heated rear window.2. Disconnect the aerial cable from the radio aerial control unitin the heated rear window.3. Undo the nuts (3a) and remove the radio aerial control unit inthe heated rear window (3b).2010708
5570T36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Undo the wing bolts and removethe boot left side trim. Make sure that the ignition is in the OFFposition, then disconnect the negative battery terminal (refer toop. 33148615530B10battery - r+r ). 1. Undo the bolts (1a) and remove the embellishment (1b).2010709
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis in the OFF position, then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315014-7005E22l/h or r/h front door panel radio grille (one) -r+r . 1. Undo the fixing bolts.2. Disconnect the electrical connection.3. Remove the front speaker.2010712
5570T92
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis in the OFF position, then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314984-7005C44interior handle panel - r r . 1. Rotate and remove the front tweeter (1a), releasing the clips(1b).2010713
5570T98
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis in the OFF position, then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), release the attachments (1b) and removethe rear speaker protective grille (1c).2. Undo the bolts fixing the rear speaker to the rear parcel shelf.3. Disconnect the electrical connection from the rear speaker.4. Remove the speaker.2010714
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
