DescriptionA device allows the headlamp beam to be adjusted, directly from the driver's seat, in accordance with the load. The headlamps are thus always aligned quickly and correctly.The adjustment device consists of a motor mounted on each of the two headlamps which tilts them as appropriate, lowering the light beam if the car is heavily laden, and raising it if the load decreases.A specific knob on the dashboard selects the four positions indicated:position 0 - one or two persons on the front seats, full fuel tank, car fully equipped and in running order;position 1 - five persons;position 2 - five persons with full boot (about 50 kg);position 3 - driver and 300 kg load, all stowed in boot.The adjustment button is on the facia, together with the exterior lighting control and the instrument lighting dimmer switch; The knob has a symbol which lights up when the side lights are on.The device is enabled only when the dipped beam headlamps are on.The headlamp adjustment circuit is protected by the same fuses as the dipped beam headlamps circuit, located in the junction unit.
Functional description The headlamp alignment device in H15 is supplied at pin 2 by a line coming from the circuit for the dipped beam headlamps ( 3309117SeeE2011DIPPED HEADLAMPS ); this line provides voltage to the regulator only when the dipped beams are on. The dipped beam switch on the exterior lights control H6 receives ignition-operated supply (INT/A) to pin 7, through fuse F1 of junction unit B1 . When the lights are switched on, the command is sent via the stalk unit B5 to pin 6 of connector B of M45 . When this signal is received, check device M45 controls the supply to the dipped beams from pin 5 of connector D; this signal excites relay R1 , located in relay unit B3 that supplies power to dipped beams and control H15 through fuse line F7 of B3 . Pin 3 of device H15 is earthed, while pin 1 sends an adjustment signal to the motors located in light clusters F10 (left) and F11 (right). A resistance divider alters output voltage to according to which of the four positions has been selected. Motors N30 and N31 contain a transducer that establishes actual motor travel on the basis of the voltage of an adjustment signal received by pin 2 from device H15 . The motors are supplied through pin 3 from the line (part of the dipped beam circuit) that supplies device H15 , while pins 1 are earthed.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Release the retaining spring (1a) and remove the protective cover(1b).2. Disconnect the electrical connection from the lamp.3. Release the retaining spring (3a) and remove the lamp (3b) fromthe light cluster.767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010662
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Rotate the bulb holder (1a) in an anti-clockwise direction untilit is released from the light cluster (1b).2. Disconnect the electrical connection (2a) and extract the bulbholder.3. Separate the lamp from the bulb holder (press fit).767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010663
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve.Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen with an opaque surface, 10 metres away, whichcontains the following lines.1. V - V: vertical corresponding to the trace of the vehicle symmetryplane.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal corresponding to the height from the groundof the reference centres for the light clusters.4. AC - AC: horizontal 11 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2010664
5540B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2. Disconnect the electrical connection from the headlamp alignmentmotor.2010666
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the control unit fixing bolts.2071307
5540B44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010672
5540B46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010675
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010678
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal1. Undo the bolt (1b) and open the fuse access cover (1b).2. Remove the complete exterior light switch (2a) from its housingusing the tool (2b).767Exert pressure inside the exteriorlights switch to facilitate its removal.3. Disconnect the electrical connections (3a), (3b) and (3c) andremove the exterior lights switch (3d).2010651
5540A56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010652
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the fixing knob (1b) and open the access cover (1a) .2. Disconnect the electrical connection from the inner rear lightcluster.3. Undo the nuts (3a) and remove the inner rear light cluster (3b).2010654
5540A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Open the access cover after having undone the fixing knob.2. Release the retaining tabs (2a) and extract the bulb holder (2b)from its housing.3. Replace the rear fog lamps bulb (3a) or the reversing lightsbulb (3b) or the side lights bulb (3c).2010655
5540A80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010656
5540A94
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), remove the complete number plate light (1b).2. Disconnect the electrical connection and remove the number platelight.2010658
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010681
5540C24
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the headlamp alignmentadjustment motor.2. For the left light cluster alignment motor only, open the spring(2a) and remove the main beam headlamp bulb protective cover (2b).3. Rotate the light cluster alignment motor in a clockwise directionand remove it.2010683
5540C40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas lightcluster alignment motor.2010684
5540C42
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the light cluster alignmentfront sensor.2. Undo the nut (2a) and disconnect the connecting rod (2b) fromthe light cluster alignment front sensor.3. Undo the nuts (3a) and remove the light cluster alignment frontsensor (3b).4. Undo the bolts (4a) and remove the light cluster alignment frontsensor mounting bracket (4b).2010686
5540C44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp1. Undo the nuts (1a) and remove the connecting rod for the exhaustgas light cluster alignment front sensor (1b).2. Undo the nut (2a) and remove the mounting bracket (2b) for theexhaust gas light cluster alignment front sensor connecting rod.2010687
5540C46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the light cluster alignmentrear sensor.2. Undo the nut (2a) and disconnect the connecting rod (2b) fromthe light cluster alignment rear sensor.3. Undo the bolts (3a) and remove the mounting bracket (3b) completewith light cluster alignment rear sensor (3c).At the bench, undo the nuts and separatethe light cluster alignment rear sensor from the bracket.2010688
5540C48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp1. Undo the nuts (1a) and remove the exhaust gas light cluster alignmentrear sensor connecting rod (1b).2. Undo the bolt (2a) and remove the exhaust gas light cluster alignmentrear sensor connecting rod mounting bracket (2b).2010689
5540C50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis OFF (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Move the front driver's seat forwards.Cut the floor covering along the area marked.1. Extract the control unit for the exhaust gas light cluster alignmentsystem from the support guide.2. Disconnect the electrical connection from the exhaust gas headlampalignment system control unit, then remove it.2010690
English
