DescriptionThe electric front windows are operated automatically, depending on how the switch is pressed:- For the driver's window:the operation is manual (the glass goes up/down only when the button is pressed) when the button is held down for 60 to 300 milliseconds;the operation is instead automatic (the glass continues to go up/down to the end of travel, even if the button is released) when the button is held down for over 300 milliseconds;if the button is pressed again during movement of the glass, the glass is stopped instantly;if the button is pressed for less than 60 milliseconds, it is ignored (it is considered to have been knocked accidentally).- For the passenger's window:closing is only manual;opening is the same as for the driver's window (automatic).Both windows can only be operated when the ignition is ON.The control software is located in the electric front windows control unit located under the central console of the facia.The control unit also carries out a series of safety checks:The stopping of the electric windows (switching off the electric supply to the motor) is determined when the glass reaches the end of travel at top or bottom, or if an obstacle blocks the glass. This is regulated by checking the motor current;if there are faults on the electrical circuits, the control unit switches the system off temporarily (for example if the motor control signals are interrupted or if the absorbed current is below the usual values);if there is a fault in the control buttons (short circuit, or buttons jammed in the pressed position), the control unit switches the system off temporarily.The electric front window control and check circuit is protected by three specific fuses located in the junction unit.The control switch symbols are lit when the key is turned to MAR.
Functional description Control unit M81 controls the operation of the electrically-operated front windows. The power supply to control unit M81 reaches pin 2 of connector E from the line of maxifuse CENTR of B5 , protected by fuse F15 of junction unit B1 . The ignition-activated power supply (INT/A) reaches pin 4 of connector B from the line of relay R1 , protected by fuse F9 : both are contained within junction unit B1 . Pins 3 of connector B and 1 of connector E supply earth, C20 . Switches H44 (electrically-operated window control unit on driver's door) and H50 (passenger side front door electrically-operated window switch) are supplied when the ignition is turned on (INT/A) from a line from fuse F5 , of junction unit B1 , and are connected respectively to earth C15 and C20 . This means they are also lit when the key is turned to MAR. This means they are also lit when the key is turned to MAR. When the switches are operated, they send control signals (positive and negative) to control unit M81:to pins 3 and 4 of connector A from switch H44 , to control the left-hand electrically-operated window;at pins 5 and 6 of connector A from switch H44 ; or pins 1 and 2 of connector C from switch H50 , to control the right electric windowControl unit M81 controls the electrically-operated windows as described previously:pins 1 and 2 of connnector D send commands to the left electric front window motor N60 .pins 3 and 4 of connector D send commands to right electric front motor N61 .When the positive and negative signals are reversed, the motor direction of rotation is also reversed.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315016-7005E38front side door interiorhandle-r r1. Unscrew retaining bolts (1a) and remove switch unit protectivecover (1b).2. Apply slight pressure to switches (2a) and push sideways usingtool (2b) to separate the printed circuit complete with switches(2c) from the three retaining pins on the grip and from the retainersinside the switch unit.2010790
7005M12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315016-7005E38front side door interiorhandle-r r1. Prise the switch out of its housing and press the switch in fromthe outside to remove.2010791
7005M20
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7005A04 front side door waterguard protection - r r or replace with door panel removed 1. With the window fully raised, arrange a device to support thewindow in raised position.2. Unscrew the nuts retaining the window bracket.3. Unscrew the nuts retaining the slide bracket.4. Unscrew the window motor retaining bolts.5. Adjust the electrically-operated window until the window isclosed, disconnect the window motor electrical connection.6. Remove the electrically-operated window from the door compartment.2010792
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 7005A04 front side door waterguard protection - r r or replace with door panel removed Open and close the windows a few timesto check for adjustment defects (window does not quite reach the topor the rear door pillar).1. With the window fully raised, loosen both nuts retaining theelectrically-operated window device to the window.2. Place the window in the correct closure position by hand (windowreaches top and rear edges).3. Operate the window device electrically, fit it against the glassand tighten the retaining bolts.2010793
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in tthe OFF position, then disconnect the battery negative terminal.1. Undo the bolts (1a) and remove the right and left trims (1b).2010794
Русский
