DescriptionThe side lights come on when the selector on the left side of the facia is turned to the first position and only work with the key turned to MAR.They can also be turned on by turning the switch in an anti-clockwise direction - park position. In this case their operation is independent of the position of the ignition switch.Under these conditions, if the turn signal lever is in the right or left selection position, the parking lights are turned on only on the selected side.Turning on the side lights also turns on the number plate lights and numerous other interior lights for passenger compartment lighting and instrument & control lighting (these lines are described and illustrated in the diagrams for the components to which they refer).The circuit is protected by two fuses, one for the right-hand lights, one for the left-hand lights.A warning light on the instrument panel indicates that the side lights have been turned on. Operation of the side lights and number plate lights is monitored by the exterior light check device.The following faults may occur:blown bulbbulb s.c. to earth or positiveA special light failure warning light on the dashboard comes on for all other faults in the various circuits. This warning light comes on for about 6 seconds when the ignition key is turned to MAR, to indicate it is working properly, then it goes off.
Functional descriptionThe side lights and parking lights are controlled by the electronic Check device M45, that receives control signals from the switches and controls the bulbs while also checking the various lines.Check device M45 is supplied directly from the battery. (maxifuse CENTR of B5) to pins 1 and 6 of connector C, via fuse F11 of junction unit B1.An ignition-operated power supply (INT/A) reaches pin 9 of connector C through fuse F1 of junction unit B1: pin 7 of connector C is earthed.The outside lights control H6 side lights switch receives a go-ahead from pin 5 of connector A; when the lights are on, it sends a command to pin 4 of connector A of M45.In response to this signal the Check device M45 controls the supply of the front side lights F01 (left) and F11 (right) from pins 6 and 4 of connector D; the rear lights F30 and F35 (left), F31 and F36 (right) from pins 11, 2, 3, 12 of connector E; and, lastly, the number plate lights F50 and F51 from pins 1 and 6 of connector E.At the same time the 'side lights on' warning light on the instrument panel E50, pin 5 of connector C, is turned on from pin 9 of connector B, while pin 15 of connector A supplies the ignition-controlled supply to the panel, through fuse F1 of the junction unit B1.The parking lights switch of the exterior lights control H6 receives enablement from pin 13 of connector A and sends the command to pin 9 of connector A of M45.In response to this signal, the Check device M45 controls the supply to the side lights as described above.When the parking lights are switched on, a control is send from pin 12 of connector B to the stalk unit B5. if from the stalk unit B5 a signal reaches pins 4 and 5 of connector B indicating the selection of the right or left indicators, the Check device M45 controls the supply of the side lights only on the selected side.The device M45 checks the efficiency of the bulbs and their connections: if faults are detected in the circuit, the 'lights fault' warning light on the instrument panel E50, pin 7 of connector C, is lit from pin 6 of connector A, while pin 15 of connector A supplies an ignition-operated power supply to the panel through fuse F1 of the junction unit B1.The exterior lights control H6 is illuminated when the ignition is on (INT/A), through the line of fuse F15 to the fuse and relay unit B1.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Release the retaining spring (1a) and remove the protective cover(1b).2. Disconnect the electrical connection from the lamp.3. Release the retaining spring (3a) and remove the lamp (3b) fromthe light cluster.767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010662
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Rotate the bulb holder (1a) in an anti-clockwise direction untilit is released from the light cluster (1b).2. Disconnect the electrical connection (2a) and extract the bulbholder.3. Separate the lamp from the bulb holder (press fit).767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010663
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve.Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen with an opaque surface, 10 metres away, whichcontains the following lines.1. V - V: vertical corresponding to the trace of the vehicle symmetryplane.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal corresponding to the height from the groundof the reference centres for the light clusters.4. AC - AC: horizontal 11 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2010664
5540B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Position the vehicle on theramp. Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2. Disconnect the electrical connection from the headlamp alignmentmotor.2010666
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the control unit fixing bolts.2071307
5540B44
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010672
5540B46
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010675
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2010678
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal1. Undo the bolt (1b) and open the fuse access cover (1b).2. Remove the complete exterior light switch (2a) from its housingusing the tool (2b).767Exert pressure inside the exteriorlights switch to facilitate its removal.3. Disconnect the electrical connections (3a), (3b) and (3c) andremove the exterior lights switch (3d).2010651
5540A56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010652
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the fixing knob (1b) and open the access cover (1a) .2. Disconnect the electrical connection from the inner rear lightcluster.3. Undo the nuts (3a) and remove the inner rear light cluster (3b).2010654
5540A74
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Open the access cover after having undone the fixing knob.2. Release the retaining tabs (2a) and extract the bulb holder (2b)from its housing.3. Replace the rear fog lamps bulb (3a) or the reversing lightsbulb (3b) or the side lights bulb (3c).2010655
5540A80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010656
5540A94
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), remove the complete number plate light (1b).2. Disconnect the electrical connection and remove the number platelight.2010658
Русский
