DescriptionAn automatic system manages the climate control in the passenger compartment, i.e. temperature and ventilation, with recirculation and air flow orientation.A dedicated control unit manages system operation by controlling:air temperature at outlets;fan speed;air distribution;activation of the compressor (air refrigeration circuit);activation of air recirculation.The control unit sets the above parameters in order to adjust passenger compartment temperature to the required level.The control unit supplies information on interior and exterior temperature via special sensors. After processing the information, it adjusts the passenger compartment air intake speed by means of the fan motor and the air temperature by a mxer actuator. It also controls interior air recirculation via a specific actuator. When required, the ECU automatically activates the cooling circuit and dehumidifies the air by operating the air conditioner compressor. ( 3309931SeeE6021COMPRESSOR ENGAGEMENT ). In addition to the climate control commands described above, the climate control system also comprises the solar radiation sensor located in the middle at the base of the windscreen; this sensor enables you to foresee an increase in temperature in the interior compartment caused by heat from solar radiation, and consequently appropriate strategies are adopted to improve climatic comfort in the car. For greater detail, see 3308537see DESCRIPTION AND OPERATION:5040AIR CONDITIONING CASING AND COMPONENTS . The control unit supply lines are protected by a fuse in the junction unit.The fan supply line is protected by a special maxifuse.The system will only operate when the ignition is turned to MAR.
Functional description Control unit M70 is supplied when the ignition is turned on (INT/A) at pin 11 of connector B from a line protected by fuse F9 from junction unit B1 .; The power supply comes directly from the battery to pin 10 of connector C through fuse F17 of junction unit B1 and a line protected by maxifuse CENTR of B5 . Pin 8 of connector C of M70 is earthed. The outdoor temperature sensor is located on the left door mirror P60 : the sensor is connected to pins 1 and 7 of connector A of M70 . Control unit M70 is also connected to sensors K87 (lower treated air), K88 (upper treated air) and K89 (passenger compartment air), which are connected to pins 3-5, 11-12 and 8-13 of connector A of M70 respectively. Sensor K89 is fitted with a fan motor so that the temperature reading is not affected by the motionless and thus warmer air inside the facia: the motor is connected to the control unit via pins 10 and 12 of connector B. Solar radiation sensor K90 is connected to pins 6 and 15 of connector A of M70 . The air conditioning system is equipped with three activators for recirculation ( N82 ), air mixing ( N81 ) and air distribution ( N80 ). Recirculation actuator N82 is controlled by control unit M70 , via pins 3 and 4 of connector B. The air mixing actuator N81 is controlled from pins 1 and 2 of connector B from control unit M70 ; it receives a supply for control by potentiometer from pin 20, the reference earth to pin 14 at connector A, and sends a feedback signal to pin 16 of connector A. The air distribution actuator N80 is connected from pins 7 and 8 of connector B from control unit M70 ; it receives a supply for control by potentiometer from pin 18, the reference earth at pin 2 of connector A, and sends a feedback signal to pin 17 of connector A. An electronic governor operates fan N85 at different speeds: this receives a control signal from control unit M70 - from pin 2 of connector C - and converts it to a variable voltage signal that controls the fan. Pin 1 of connector C provides a reference earth, pin 6 of connector C of M70 provides a speedometer signal. Fan unit N45 is supplied when the ignition is turned on (INT/A) via relay J35 and fuse B65 . Pin 4 of connector C of M70 receives a speedometer signal from instrument E50 . A heated back window activation control - from pin 9 of connector B - is sent to control unit M45 ( SeeE3030 HEATED REAR WINDSCREEN AND DOOR MIRROR DEFROSTING . ) Pin 6 of connector B controls activation of the compressor ( 3309931SeeE6021COMPRESSOR ENGAGEMENT ). Climate control unit H80 communicates with control unit M70 via a serial connection line: from pin 13 of connector C of M70 to pin 9 of H80 . The supply to the climate control unit H80 arrives directly from the battery. (maxifuse CENTR of B5 ) to pin 1, via fuse F18 of junction unit B1. An ignition-operated power supply (INT/A) reaches pin 2 via fuse F5 of junction unit B1; pin 7 is earthed. Climate control unit H80 is then connected - from pin 8. to ICS display E60 - pin 15 of connector B, via a special serial connection line. Control unit M70 is equipped with a self-diagnostic system, that may be used by connecting to connector R10 : it receives signals from pin 13 of connector C of M70 through a serial connection line between control unit M70 and climate control unit H80 ; from here it is connected to the ICS display E60 . Control unit H80 also receives other signals for the Trip Computer function of the ICS display: these signals are then exchanged with display E60 via the above serial line ( 3309749SeeE4090NAVIGATOR ).
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Working in the luggage compartment, undo the knob for the batterycover.2. Remove the battery cover.2010650
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314917-5560B11analogue control panel- r+r or replace . 1. At the bench, remove the bulbs from the panel using suitablepliers.2010702
5560B11
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Undo the wing bolts and removethe boot left side trim. Make sure that the ignition is off (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). Disconnect the electrical connections forthe loudspeakers' amplifier.1. Undo the nuts and move aside the on-board navigator componentsmounting as far as necessary.Disconnect the electrical connection fromthe navigation system CD player/changer.Disconnect the electrical connections ofthe audio CD player/changer.2. Remove the complete on-board navigator components mounting.2010738
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314810-5050B34windscreen wiper arm/s complete with blade - r+r . 3315282-7055A18Windscreen base TRIM - R.R. . 1. Disconnect the electrical connection for the intake/recirculationair flap actuator.2. Undo the bolts (2a) and loosen the bolt (2b) for the recirculation/intakeair flap actuator using the tools (2c) and (2d).3. Disconnect the linkage (3a), rotate the recirculation/intakeair flap actuator (3b), completely undo the remaining bolt and removeit.2010575
5040D70
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314729-5010B52ducts (one), lh or rh,on air distribution unit for air duct beneath facia r r with faciaremoved . 1. Disconnect the electrical connection for the distribution airflap actuator.2. Undo the fixing bolts and move the distribution air flap actuatoraside.3. Undo the bolts (3a) and remove the actuator mounting bracket(3b).4. Release the wiring and remove the distribution air flap actuator.2010576
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213314930-5580C14air bag ecu - r+r . 3315223-7040L20tunnel trim - r r . - 7045A10 l/h or r/h front seat (one) - r+r . 1. Move the floor covering and undo the nut fixing the steeringcolumn universal joint protection.2. Remove the universal joint protection.3. Undo the bolt fixing the steering column to the power steeringbox pinion.4. Push back the steering column joint.2010556
5040C16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts (1a) and remove the distribution air flap motor(1b) complete with bracket.2010562
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release the electrical connection for the air conditioning fanfrom the fixing on the casing.2. Undo the bolts (2a) and remove the air conditioning fan (2b).2010567
5040C50
768
5040C52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21- 1088A20 engine cooling system- wash inside . 1. Undo the bolts (1a) and remove the duct (1b).2. Disconnect the coolant inlet and outlet pipes from the air conditioningheater radiator.3. Remove the heater radiator.2010568
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts (1a) and separate the fan unit (1b) from the airconditioning unit (1c).2. Undo the bolts (2a) and remove the pollen filter filter element(2b).3. Undo the bolts (3a) and remove the bracket (3b).2010569
5040C80
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the bolts (1a) and remove the intake/recirculation air flapactuator (1b).2. Remove the intake/recirculation air flap control linkage.3. Remove the hinge pin (3a) and remove the intake/recirculationair flap (3b).2010571
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315037-7005R35door mirror reflector- r r . 3315012-7005E12corner cover of one front side door, lh or rh r r . 1. Undo the bolts (1a) fixing the starter motor support and thebolts (1b) fixing the cover to the support.2. Remove the outside air temperature sensor.3. Extract and open the connection holder.4. Disconnect the electrical connection for the outside air temperaturesensor and remove it.2010421
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection for the upper mixed airtemperature sensor.2. Remove the upper mixed air temperature sensor (2a) using thetool (1b).2010422
5010D26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection for the lower mixed airtemperature sensor.2. Remove the lower mixed air temperature sensor (2a) using thetool (2b).2010423
5010D30
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2010424
5010D56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314734-5010C30central air outlet on fascia - r+r . 3314917-5560B11analogue control panel - r+r or replace . 1. Release the electrical wiring for the solar sensor from the fixingband.2. Disconnect the electrical connection for the solar sensor.3. Remove the solar sensor (3a) from the dashboard using the tool(3b).2010427
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 3314767-5040A10Air conditioning refrigerant CIRCUIT - Draining andRefilling . 1. Disconnect the electrical connection for the air conditioningsystem multi-stage pressure switch.2. Undo and remove the air conditioning system multi-stage pressureswitch.2010547
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315012-7005E12corner cover of onefront side door, lh or rh r rWith the ignition key in the OFF position,disconnect the battery negative terminal.Take out the connector carrier and openit.1. Disconnect electric mirror wiring connectors (1a), (1b) and(1c). 2. Remove bolt cover panel (2a) and uncrew the bolts (2b) securingthe mirror to the door.3. Withdraw the wiring and remove the mirror.2010797
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Use tool (1a) to prise out reflector (1b).1. Disconnect the electrical connections from the reflector andthen remove.2010798
7005R36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315037-7005R35door mirror reflector- r r1. Unscrew the motor retaining bolt.2. Disconnect the electrical connections shown.3. Remove the positioning motor.2010799
7005R37
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213315037-7005R35door mirror reflector- r r3315038-7005R36door mirror motor - r r1. Unscrew the bolts retaining the cover to the mount.2. Unscrew the bolts retaining the motor mount to the cover.3. Cut the electrical wiring retaining strip and prise the outdoortemperature sensor out of the cover.4. Remove the rear view mirror cover.2010800
7005R40
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21With the ignition key in thestop position, disconnect the battery negative terminal.1. Take the control switch unit out of the handle by undoing theretaining clip.2. Disconnect the electrical connectors.3. Remove the control switch unit.2010801
Русский
