Fiat BRAVO 1.9 JTD 8v – BOOT OPENING – – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION – WIRING DIAGRAM, LOCATION COMPONENTS, OPERATIONAL DESCRIPTION

WIRING DIAGRAM - BOOT OPENING - Fiat BRAVO 1.9 JTD 8v

BOOT OPENING - WIRING DIAGRAM Fiat BRAVO 1.9 JTD 8v

COMPONENTS - BOOT OPENING - Fiat BRAVO 1.9 JTD 8v

Component code	Description	Reference to the operation
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXI FUSE BOX ON BATTERY	-
C030	LEFT REAR EARTH	-
C038	EARTH ON CENTRE TUNNEL	-
E050	INSTRUMENT PANEL
H001	IGNITION SWITCH
H090	SWITCH CONTROL PANEL
I033	SWITCH ON BOOT OUTER HANDLE
M001	BODY COMPUTER
M080	CENTRAL DOOR LOCKING CONTROL UNIT
N057	BOOT LOCK GEARED MOTOR
P093	AERIAL FOR ALARM AND CENTRAL LOCKING RECEIVER	-

COMPONENT LOCATION - BOOT OPENING - Fiat BRAVO 1.9 JTD 8v

BOOT OPENING - COMPONENT LOCATION Fiat BRAVO 1.9 JTD 8v

모든 배선 다이어그램에 액세스하십시오.

Component code	Description	Reference to the operation
B002	JUNCTION UNIT UNDER DASHBOARD
B099	MAXI FUSE BOX ON BATTERY	-
C030	LEFT REAR EARTH	-
C038	EARTH ON CENTRE TUNNEL	-
E050	INSTRUMENT PANEL
H001	IGNITION SWITCH
H090	SWITCH CONTROL PANEL
I033	SWITCH ON BOOT OUTER HANDLE
M001	BODY COMPUTER
M080	CENTRAL DOOR LOCKING CONTROL UNIT
N057	BOOT LOCK GEARED MOTOR
P093	AERIAL FOR ALARM AND CENTRAL LOCKING RECEIVER	-

DESCRIPTION - BOOT OPENING - Fiat BRAVO 1.9 JTD 8v

The boot opening geared motor is operated by:- the remote control;- the button in the rear handle;- the unlocking button in the control unit in the centre of the dashboard, right sideOperation through the remote control takes place in two ways.- indepedently of the doors: there is a special button on the remote control that allows the boot only to be "unlocked": the boot is released and lifts up slightly. The operation is signalled by the direction indicators flashing twice; when it is closed again the boot returns to the state prior to opening.- together and at the same time as the unlocking of the doors: the tailgate is considered as a fifth door to all intents and purposes: for the control logic.The boot unlocking function is controlled by the Body Computer, but activated by the central locking power module.The locking/unlocking power module receives a power supply from a line protected by a specific fuse in the junction unit under the dashboard.

FUNCTIONAL DESCRIPTION - BOOT OPENING - Fiat BRAVO 1.9 JTD 8v

The boot opening function is controlled by the Body Computer M1 and activated by the central locking power module M80 controlled by the Body Computer M1.Body Computer M1 receives the following inputs:- door lock/release signals from the aerial-receiver of remote control unit P93, which are connected to pins 30 and 43 of connector B of M1;- the negative signal from the boot unlocking button, located in the control unit H90, at pin 22 of connector H of M1;- the negative signal from the button in the rear handle I33, from pin 47 of connector E of M1.The Body Computer M1 receives a direct supply from the battery via the line protected by maxifuse B99 at pin 18 of connector F of the interface with the junction unit under the dashboard B2; the ignition-controlled supply (INT) reaches pin 9 of connector F of the interface with the junction unit B2.The central locking power module M80 receives a power supply from the line protected by fuse F36 of the junction unit under the dashboard B2.Depending on the operating logic illustrated, the Body Computer M1 operates the central locking power module M80 which, in turn, activates the geared motor in the boot lock via a relay: the command is sent from pin 41 of connector E to the module M80 which, in turn, activates the motor for lock N57.Body Computer M1 is connected via the CAN line to instrument panel E50, to which it sends a signal that turns on the boot open warning light, where necessary, and activates the buzzer to give an acoustic signal.