Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
WIRING DIAGRAM - COURTESY LIGHTS - Fiat GRANDE PUNTO 1.2 8v
COMPONENTS - COURTESY LIGHTS - Fiat GRANDE PUNTO 1.2 8v
| Component code | Description | Reference to the operation |
| B001 | JUNCTION UNIT | |
| B099 | MAXI FUSE BOX ON BATTERY | |
| C015 | DASHBOARD EARTH, DRIVER'S SIDE | - |
| C030 | LEFT REAR EARTH | - |
| D030 | DRIVER'S FRONT DOOR COUPLING | - |
| D031 | PASSENGER FRONT DOOR COUPLING | - |
| D035 | LEFT REAR DOOR COUPLING | - |
| D036 | RIGHT REAR DOOR COUPLING | - |
| E050 | INSTRUMENT PANEL | |
| G010 | FRONT COURTESY LIGHT | |
| H001 | IGNITION SWITCH | |
| M001 | BODY COMPUTER | |
| N050 | DRIVER'S FRONT DOOR LOCK GEARED MOTOR | |
| N051 | RIGHT FRONT DOOR LOCK GEARED MOTOR | |
| N055 | LEFT REAR DOOR LOCK GEARED MOTOR | |
| N056 | RIGHT REAR DOOR LOCK GEARED MOTOR |
COMPONENT LOCATION - COURTESY LIGHTS - Fiat GRANDE PUNTO 1.2 8v
| Component code | Description | Reference to the operation |
| B001 | JUNCTION UNIT | |
| B099 | MAXI FUSE BOX ON BATTERY | |
| C015 | DASHBOARD EARTH, DRIVER'S SIDE | - |
| C030 | LEFT REAR EARTH | - |
| D030 | DRIVER'S FRONT DOOR COUPLING | - |
| D031 | PASSENGER FRONT DOOR COUPLING | - |
| D035 | LEFT REAR DOOR COUPLING | - |
| D036 | RIGHT REAR DOOR COUPLING | - |
| E050 | INSTRUMENT PANEL | |
| G010 | FRONT COURTESY LIGHT | |
| H001 | IGNITION SWITCH | |
| M001 | BODY COMPUTER | |
| N050 | DRIVER'S FRONT DOOR LOCK GEARED MOTOR | |
| N051 | RIGHT FRONT DOOR LOCK GEARED MOTOR | |
| N055 | LEFT REAR DOOR LOCK GEARED MOTOR | |
| N056 | RIGHT REAR DOOR LOCK GEARED MOTOR |
DESCRIPTION - COURTESY LIGHTS - Fiat GRANDE PUNTO 1.2 8v
There is only one bulb in the front courtesy light which can be switched on or off using the relevant switch or through a delay timer as described below.The courtesy light operation is timed according to a logic managed by the body computer:- when any of the doors is opened, it comes on for 3 seconds; the timer is reactivated whenever the door is opened;- when all the doors are closed; the lights stay on for a further 10 seconds with the key off. This time is interrupted if the key is moved to key on position: in this case, the courtesy lights are turned off immediately.- When all the doors are closed at key-on the courtesy lights are immediately switched off.- when the key is removed, the courtesy light comes on and a 10 second timer is activated.- all the courtesy lights are turned off immediately at the door lock control;- at the door release command, the courtesy light is turned on and a 10 second timer is activated.- If the inertia switch is operated the courtesy light comes on for 15 minutes.The switching on or off takes place gradually (dimmer) with the cycle lasting 2 seconds.The courtesy light power supply follows a battery voltage control logic: with the key off when any door or the boot is opened, a time of 15 seconds is set. After this, all the courtesy light is deactivated.If one or more doors are open, this is shown on the instrument panel display; the warning light remain on until all the vehicle doors and boot lid are properly shut. If a given speed limit is exceeded, this is also signalled by means of a buzzer.
FUNCTIONAL DESCRIPTION - COURTESY LIGHTS - Fiat GRANDE PUNTO 1.2 8v
The Body Computer M1 receives "door open" input signals at pin 57 (driver''s front door) pin 41 (left rear door) pin 56 (front passenger door) and pin 55 (right rear door) of connector A of M1.Front courtesy light G10 is supplied by a line protected by fuse F53 located on Body Computer M1.Front courtesy light G10 is supplied from Body Computer M1 in accordance with the strategy described previously from pin 25 of connector E, while the timed command analogue signal is received from pin 3 of connector C.Body Computer M1 - connector G - is supplied directly from the battery from a line protected by maxifuse F2 of engine compartment control unit B1. It is ignition-operated (INT) at pin 32 of connector D. Pin 10 of connector H of M1 supplies a reference earth to the Body Computer.Body Computer M1 is connected via the CAN line to instrument panel E50, to which it sends a signal that turns on the door open warning light, where necessary, and activates the buzzer to give an acoustic signal.
