DescriptionThe left and right direction indicators are operated by raising or lowering the left lever on the stalk unit. the function is activated with the ignition key in the ON position.The hazard warning lights (right and left direction indicators operated simultaneously) are turned on by the pressing a button in the centre of the dashboard between the climate control system controls and both the direction indicators come on at the same time. An LED in the back of the button also comes on flashing in synchronization with the outside lights; the function is always activated.The switching on of the direction indicators / hazard warning lights is managed by the Body Computer which also controls the flashing frequency which is sent to the other connectors via the CAN serial network.In this way, the two direction indicator warning lights in the instrument panel are also lit up; in addition, as well as the activation of the lamps, the system also produces a low frequency auditory signal.The correct operation of the lights is controlled by the direction indicators 'check' function: the following is controlled for each of the two circuits (right branch and left side):open circuit or bulb missingshort circuit to earth (bulb short circuit or wiring short circuit to earth)short circuit to Vbatt (wiring short circuit to Vbatt)If one of the situations described above is detected, the Body Computer notifies the CAN of the failure state: the special 'lights failure' warning light in the instrument panel comes on and, at the same time, the information is shown on the display.In addition, at the same time as the failure indication is activated, the frequency of the flashing for the visual display in the panel and the auditory signal increases; the frequency of the flashing of the exterior lights and the LED in the hazard warning lights button, on the other hand, remains unchange.23 the direction indicators are also used to signal the receipt of the commands sent by the remote control and/or to signal a manoeuvre not carried out by the 'passenger compartment access' control system 2399254SeeE3040CENTRAL LOCKING .
Functional description The turn signal activation (earth) signals are sent to pins 7 of connector I and 30 of connector G of the Body Computer M1 from the steering column switch unit H5. The hazard warning lights activation signal, on the other hand, reaches pin 34 of connector G of M1 from the control button in the climate control system controls H80 (or M70). The direct supply for the climate control system H80 controls (or M70) arrives via the line of fuse F39 of the junction unit under the dashboard B2; pin 7 of connector A is earthed (earth controlled by the Body Computer M1). The Body Computer M1 receives a specific direct supply for the hazard warning lights via fuse line F53 of the junction unit under the dashboard B2; as a result, it controls the side direction indicators F20 (left) and F21 (rght) from pins 2 and 13 of connector D, the front side lights F10 (left) F11 (right) from pins 38 and 39 of connector B and for the rear side lights F30 (left) F31 (right) from pins 12 and 3 of connector D. The (positive) signal is sent, from pin 29 of connector G of M1, to light up the LED in the climate control system controls button H80 (or M70). The Body Computer M1 is connected, via the CAN line, to the instrument panel E50, to manage the 'direction indicators' warning light, the buzzer and, if there are failures in the circuit, the 'lights failure' warning light.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve and driveron board. Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen or an opaque surface, 10 metres away,which contains the following lines. 1. V - V: vertical line corresponding to the plot of the plane ofsymmetry of the vehicle.2. C - C: plots of the vertical planes passing through the referencecentres of the lights clusters. 3. HC - HC: horizontal line corresponding to the height from theground of the reference centres for the lights clusters. 4. AC - AC: horizontal line 12 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2050815
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Rotate in an anti-clockwise direction and withdraw the cover.2050805
5540B25
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b).2050808
5540B26
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b2050811
5540B28
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Turn the cover retainer.2. Remove cover (2a), releasing the retainers (2b).2050813
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove side repeater (1a), release the retainers (1b) and then(1c).2. Rotate and extract the bulb holder with the bulb.3. Recover the side repeater.2050827
5550C54
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400607-5550C22l/h or r/h side flasher(one) - r+r1. Extract the bulb (1a) from the bulb holder (1b) (press fit).2050828
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the tailgate.1. Remove the flap (1a) releasing the retainers (1b) and then (1c). 2. Disconnect the electrical connection.3. Unscrew the nuts.4. Remove the light cluster from the outside.2050801
5540A50
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400584-5540A44l/h or r/h tail light(one) - r+r1. Release retainers (1a) and raise bulb holder (1b) with seal.2050802
5540A94
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Release retainer (1a) and then (1b). Recover the lens protection(1c).2. Remove bulb (2a) by releasing side retainers (2b).23 The number plate light bulb holderis an integral part of the outer handle; to remove it 2400752-7015B30exterior handle or blocksupport - r+r with panel/protection removed2050804
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400797-7040A19cushion padding - rr1. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor releasing the intake.2050724
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400797-7040A19cushion padding - rr1. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor releasing the intake.2050726
5040D94
23
5040D96
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400797-7040A19cushion padding - rr1. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor releasing the intake.2050728
