DescriptionThis device allows maximum ease of manoeuvring during parking; with reverse gear engaged, it indicates if the driver is approaching an obstacle that could be outside his field of vision, as illustrated in the diagram below. The system operates in accordance with the ultrasound 'sonar' principle: four ultrasound transducers are located in the rear bumper. They send signals to a control unit, which processes this information and determines the distance of possible obstacles. A loudspeaker controlled by the control unit emits an intermittent tone, proportional to the distance of the obstacle detected. The control unit is activated when reverse gear is engaged: under these conditions it energizes the transducers and sends them a signal request, and receives response signals from them. Via the specific loudspeaker, the control unit emits a signal with an intermittent tone: this sound increases in frequency as the bumper comes closer to an obstacle.If the distance measured from the obstacle increases, or if the driver disengages reverse gear, the sound stops. If the distance measured from the obstacle remains constant, the sound ceases after about 3 seconds. The signal that the reversing light has been switched on is managed by the Body Computer node which forwards this information to the parking sensor control unit via the CAN network.
Functional description The body computer node M001, at pin 1 connector C, receives the signal (positive) that reverse gear is engaged, from the switch I020. From pin 6 connector G, the body computer node informs the parking sensors control unit M084 (pin 13) that reverse gear has been engaged. The control unit M084 supplies the parking sensors unit K097, providing the supply from pin 5 and the earth reference to pin 6. From pins 1, 2, 3, 4, the parking control unit receives the signals provided by the parking sensors unit K097. The parking control unit M084 manages the operation of the loudspeaker P044, used for acoustic signalling of obstacle detection. The system fault is indicated by a warning light located in the instrument panel E050.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the cable pass on the right side of the vehicle from itsseating and open the cover.2. Remove the adhesive tape (2a) present on the wiring (2b) andrelease the windscreen/rear window washer tubes (2c).Release the wiring from the cable pass.Following the same procedure, release thewiring from the cable pass on the left of the vehicle.2046933
5505C34
768769
5505C35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the aerial coaxial cable connections.2. Disconnect the electrical connections (2a), (2b), (2c), (2d),(2e) and (2f).2046939
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753183-7040A23frame of instrument panel on facia - r r1. Undo the retaining bolts.Partially remove the instrument panel.2. Disconnect the electrical connection.3. Remove the instrument panel.2046983
767It is not possible toorder a single lock barrel or to order barrels using only the partcode. When ordering barrels, observe the special procedure set outin operation 5580 - Special Accessories. 768769
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disengage the fixing lugs (1a) and remove the cover (1b).2046919
5505A32
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753188-7040A37fuse box cover - r r1. Undo the retaining bolts.Disconnect the electrical connections.2. Remove the body computer.2046922
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
