DescriptionThe brake lights are located at the rear in the side lights and in the central third brake light.All three bulbs are operated whenever the brake pedal is pressed, by means of a switch on the pedal itself.The circuit is supplied with the ignition switched ON and is protected by a fuse, in the junction unit under the facia.The braking signal is also taken from the ABS system (where fitted).
Functional descriptionBbrake pedal switch I030:pin 4 receives a supply controlled by the ignition from the line protected by fuse F37;when pressed, pin 2 sends the brake pedal depressed signal to pin 5 connector B of body computer node M001;on cars with ABS, this signal is distributed from short circuiting junction D097C to body computer node M001 and ABS control unit M050 See E7020 ABS .767Connection between switch I030 and underfacia junction unit B002 via junction D001. The junction is housed in the passenger compartment area in the lower part of the right front pillar near the passenger side door wiring channel.Once it has received the signal, the body computer node:pin 5 connector E supplies the brake lights housed in tail-lights F030 and F031;pin 6 connector E supplies the brake lights housed in supplementary tail-light F040.The body computer node monitors the light system to ensure it is working correctly and indicates any faults by turning on the lighting failure warning light on instrument panel E050 under the following conditions:load open;short circuit to earth;short circuit to +battery.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the cable pass on the right side of the vehicle from itsseating and open the cover.2. Remove the adhesive tape (2a) present on the wiring (2b) andrelease the windscreen/rear window washer tubes (2c).Release the wiring from the cable pass.Following the same procedure, release thewiring from the cable pass on the left of the vehicle.2046933
5505C34
768769
5505C35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the aerial coaxial cable connections.2. Disconnect the electrical connections (2a), (2b), (2c), (2d),(2e) and (2f).2046939
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753183-7040A23frame of instrument panel on facia - r r1. Undo the retaining bolts.Partially remove the instrument panel.2. Disconnect the electrical connection.3. Remove the instrument panel.2046983
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Using a suitable tool, remove the number plate light lens.2. Remove the number plate light bulb.2046962
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Rotate and remove the switch on the brake pedal.2046979
5550D16
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Undo the retaining bolts.2. Disconnect the electrical connection.3. Remove the third brake light complete with surround.2046980
5550D17
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2752991-5550D16third stop light - r+r1. Disengage the clip (1a) and remove the bulb holder (1b).2. Remove the bulb concerned.2046982
767It is not possible toorder a single lock barrel or to order barrels using only the partcode. When ordering barrels, observe the special procedure set outin operation 5580 - Special Accessories. 768769
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disengage the fixing lugs (1a) and remove the cover (1b).2046919
5505A32
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753188-7040A37fuse box cover - r r1. Undo the retaining bolts.Disconnect the electrical connections.2. Remove the body computer.2046922
