Description The car is equipped with two GAS DISCHARGE headlamps (for further details 3360690SeeE2011DIPPED HEADLAMPS ). The left headlamp is the Master control unit while the right acts as a Slave unit.The master downloads the dipped beam command, car speed and - to manage the function - signals from two sensors (potentiometric) on the wheel axles that manage front and rear ride.The control unit controls the adjustment motor - located in the headlamps - and tilts it by the required amount on the basis of input.768
767on the version with gas discharge headlamps, the light beam is adjusted automatically and the two buttons on the left side of the panel are no longer active.
The device is enabled only when the dipped beam headlamps are on. The relay which controls the switching on of the dipped beam headlamps 3360690SeeE2011DIPPED HEADLAMPS also supplies the adjustment motors built into the headlamps; this relay for switching on the dipped beam headlamps is managed by the Body Computer: the relay is energized by enablement signals of ignition on (INT) and the stalk unit dipped beam control.
Functional description The dipped beam activation signal is sent to pin 4 of connector D of the Body Computer M1 from the stalk unit H5 . The Body Computer M1 controls the supply to the dipped beam headlamps, sending an earth signal to the unit under the dashboard B2 - from pin 8 of connector F of M1 - which energizes the relay T1; this supplies the dipped beam headlamps and gives enablement to the headlamp adjustment motors F10 (left) and F11 (right). The two electronic circuits inside headlamps F10 (left) and F11 (right) are supplied - pin 9 - from the INT line protected by fuse F37 of control unit B2 . Pins 12 are both control units are interconnected, while 10 of the control unit inside headlamp F10 receives a speedometer signal from Body Computer M1 (pin 28 of connector B). Headlamp F10 contains built-in headlamp alignment control unit M73 , connected to two sensors (potentiometers) that record ride at front K1 and rear K2 . The headlamp electronic circuits use these signals to automatically adjust the light beam by means of a motor.
0Removing201Refitting21Disconnect the negative battery terminal.1. Remove the junction unit protective cover.192009560
5505A35
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363361-7040A44facia lh side cover - r r1. Disconnect the front electrical connectors of the junction unitcomplete with body computer.2. Unscrew the retaining bolts.3. Remove from its seating the junction unit complete with bodycomputer.4. Disconnect the rear electrical connectors of the junction unitcomplete with body computer.2027438
5505A36
0Removing201Refitting211. Separate the junction unit (1a) from the body computer (1b),by releasing the retaining lugs (1c).2027440
5505A41
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363151-5580C18air bag module - r+r . 769- 4110A16 steering wheel - r r for replacement or checks forversions with airbag and manual gearbox with hydraulic selection . 1. Disconnect the electrical connectors (1a) and remove the controlunit (1b) from its seating.2027441
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.1. Release the clips and remove the protective cover for the uniton the battery.2. Undo the bolts (2a) and remove the battery fixing bracket (2b).3. Slacken the nut and disconnect the battery's negative terminal.2027495
5530B52
0Removing201Refitting21Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.3363098Op. 5530B10 BATTERY - R+R3363096- Disconnect the engine management unit electrical connections.Release the wiring from the retaining bands.1. Undo the rear fixing bolt (1a), release the front fastenings (1b) and place the engine compartment junction unit (1c) at the side.192008351
5530B56
0Removing201Refitting211. Undo the fixing bolts (1a) and remove the battery cover (1b).2027502
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363357-7040A26steering column trim - r+r1. Undo the bolts fixing the analogue instrument panel trim.2. Remove the trim under the instrument panel.3. Undo the upper bolts fixing the instrument panel to the dashboard;then partly release the panel.2027547
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.1. Undo the top fixing nut (1a) on the window washer fluid reservoir(1b).2. Slacken the bottom fixing nut on the window washer fluid reservoir.2027513
0Removing201Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection for the right front lightcluster. 2062681
5540B48
0Removing201Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection for the headlamp alignmentcontrol unit.2. Adjust the clip (2a) and remove the protection (1b).2062684
0Removing201Refitting211. Disconnect the electrical connection on the front left lightscluster.2027517
5540B53
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.1. Undo the top fixing nut (1a) on the window washer fluid reservoir(1b).2. Slacken the bottom fixing nut on the window washer fluid reservoir.2027523
767 It is not possible toorder a single lock barrel or to order barrels using a single partcode. When ordering barrels, observe the special procedure illustrated 3363161See assembly5580E anti-theft device .
0Removing201Refitting211. Undo the bolts fixing the lower part of the trim.2. Remove the lower part of the trim.2027825
7040A31
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363362-7040A45facia rh side cover - r r1. Undo the fixing bolts (1a) and release the rods for the compartmentflap (1b) from the housing.2. Remove the compartment from the housing.Disconnect the electrical connector forthe glove compartment light.2027827
7040A37
0Removing201Refitting211. Undo the cover fixing bolts.2. Remove the fuse access cover in the dashboard.2027829
0Removing201Refitting211. Open the flap for the dashboard control unit complete with bodycomputer. 2. Undo the fixing bolts (2a) and remove the left dashboard sidetrim (2b).2027831
7040A45
0Removing201Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.Open the flap for the compartment in thedashboard.1. Undo the bolts fixing the right dashboard side trim.Release the right side trim from its housingand disconnect the electrical connector for the Air Bag disablingswitch.2. Remove the right side trim.2027832
0Removing201Refitting21Open the flap for the upperglove compartment.1. Undo the trim fixing bolts.2. Remove the cover.2027835
7040A60
0Removing201Refitting211. Break the fixing buttons.2. Remove the cover under the dashboard.2027836
7040A65
0Removing201Refitting213363355-7040A19cushion padding - rr1. Place one hand under the centre tunnel side trim, then pull inthe direction shown by the arrow (A) and, at the same time, extractthe trim as shown by the arrow (B). This releases the upper clips(1a) from the openings (1b) and the side clip (1c) from the opening(1d). 767Follow the procedure describedabove carefully because if you only exert force towards the outside(arrow B) then there is the risk of damaging the side clip (1c).2. Extract the side trim further outwards in order to release thebutton which is a press fit.3. Remove the centre console side trim.2027837
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.