DescriptionThe vehicle is equipped with two dipped headlamps in the light clusters.The dipped beam headlamps are switched on through the steering column switch by turning the specific ring to the position after the side lights.A special relay - in the underdashboard control unit - controls the switching on of the dipped headamps via two lines protected by special fuses.The relay for switching on the dipped headlamps is managed by the Body Computer: the energizing of the relay is activated by the go ahead signals with the ignition key in the ON position (INT) and by the specific signal from the steering column switch unit.The Body Computer also manages the 'dipped headlampa maintenence' function: when the main beam headlamps are on, the Body Computer keeps the dipped headlamps on.If the dipped headlamps and the main beam headlamps are already on and the fog lights are switched on, then the dipped headlamps are switched off.Similarly, if the dipped headlamps and the fog lights are on and main beam headlamps are switched on, then the dipped headlamps are switched off.In other words, with the main beam headlamps and the fog lights on, the dipped headlamps are always switched off.The dipped headlamps are activated automatically, via the dusk sensor, if the AUTO function is set on the steering column switch unit.The sensitivity of the sensor can be adjusted via the MODE buttons in the left panel.The 'Follow me home' function is designed to keep the dipped headlamps and the side lights on after the engine has been switched off (key in OFF position) for a time of 30 seconds or multiples thereof.Keeping the dipped headlamps on is signalled by the side lights warning light in the instrument panel remaining on.The funciton is switched on by operating the flasher lever within 2 minutes: each time the lever is operated the time the lights remain on increases by 30 seconds up to a maximum of 210 secs.Operating the flasher lever for longer than 2 seconds switches the function off; the function is also switched off if the ignition key is turned to the ON position.
Functional descriptionThe dipped headlamps activation signal is sent to pin 4 of connector I of the Body Computer The 'ignition ON' signal (INT) for the switch H1 reaches the underdashboard control unit B2 at pin 11 of connector H and from there moves on to the Body Computer M1 (pin 9 of connector F). The dipped beams are active even if dusk sensor K85 is present (signal to pin 7 of connector D of M1 ) , and AUTO function is set on stalk unit H5 (signal to pin 2 of connector I of M1 ). Dusk sensor K85 is supplied from the INT line protected by fuse F49 of control unit B2 ; The Body Computer M1 controls the supply of the dipped headlamps sending an earth signal to the underdashboard control unit B2 - from pin 8 of connector F of M1 - which energizes the relay T1: this supplies the dipped headlamps F10 (left) and F11 (right). Each circuit is protected by a control unit B2 fuse: F13 for the left headlamp and F12 for the right one.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the negative battery terminal.1. Remove the junction unit protective cover.192009560
5505A35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363361-7040A44facia lh side cover - r r1. Disconnect the front electrical connectors of the junction unitcomplete with body computer.2. Unscrew the retaining bolts.3. Remove from its seating the junction unit complete with bodycomputer.4. Disconnect the rear electrical connectors of the junction unitcomplete with body computer.2027438
5505A36
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Separate the junction unit (1a) from the body computer (1b),by releasing the retaining lugs (1c).2027440
5505A41
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363151-5580C18air bag module - r+r . 769- 4110A16 steering wheel - r r for replacement or checks forversions with airbag and manual gearbox with hydraulic selection . 1. Disconnect the electrical connectors (1a) and remove the controlunit (1b) from its seating.2027441
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connectors (1a) and (1b).2. Undo the fixing bolts (2a) and remove the door node (2b).2027444
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.1. Release the clips and remove the protective cover for the uniton the battery.2. Undo the bolts (2a) and remove the battery fixing bracket (2b).3. Slacken the nut and disconnect the battery's negative terminal.2027495
5530B52
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.3363098Op. 5530B10 BATTERY - R+R3363096- Disconnect the engine management unit electrical connections.Release the wiring from the retaining bands.1. Undo the rear fixing bolt (1a), release the front fastenings (1b) and place the engine compartment junction unit (1c) at the side.192008351
5530B56
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the fixing bolts (1a) and remove the battery cover (1b).2027502
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.1. Undo the top fixing nut (1a) on the window washer fluid reservoir(1b).2. Slacken the bottom fixing nut on the window washer fluid reservoir.2027513
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection for the right front lightcluster. 2062681
5540B48
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection for the headlamp alignmentcontrol unit.2. Adjust the clip (2a) and remove the protection (1b).2062684
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection on the front left lightscluster.2027517
5540B53
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.1. Undo the top fixing nut (1a) on the window washer fluid reservoir(1b).2. Slacken the bottom fixing nut on the window washer fluid reservoir.2027523
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection for the right front lightcluster. 2062695
767 It is not possible toorder a single lock barrel or to order barrels using a single partcode. When ordering barrels, observe the special procedure illustrated 3363161See assembly5580E anti-theft device .
5520A18
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting213363098-5530B56BATTERY DRIP TRAY COVER- R.R.Disconnect the battery negative terminal.3363357-7040A26steering column trim - r+r1. Disconnect the electrical connectors of the ignition block (1a)and Cruise Control (1b).2. Release the retaining clips on the ignition switch contact block.2027470
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
