AIR CONDITIONING
2.7L
2.7L, Manual A/C Wiring Diagram for Dodge Intrepid SE 2002
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 2.7L, Manual A/C Wiring Diagram for Dodge Intrepid SE 2002:
- (a/c heater harness, near breakout to blend door actuator)
- (center of dash)
- (engine harness, front of engine)
- (in breakout to a/c heater controls)
- (in hvac assembly, on face of evaporator) evaporator temperature sensor
- (in power distribution center) s127
- (lower center of dash) g200
- (near right horn) g105
- (right side of engine) s104
- A/c compressor clutch
- A/c compressor clutch relay (in power distribution center)
- A/c led ind sig
- A/c mode mux
- A/c mode sw mux
- A/c press sig
- A/c pressure transducer (on a/c discharge line)
- Ambient temp
- Ambient temperature sensor (at right side of headlamp mounting module grille opening)
- Blend air dr drvr
- Blend door actuator (on lower left side of hvac assembly)
- Blnd dr driver
- Blnd dr fdbk
- Blower motor
- Blower motor resistor block (on lower right side of hvac housing)
- Body control module (at left end of dash, attached to junction block)
- C10
- C12
- C18
- C24
- C26
- C27
- C28
- C32
- C33
- C34
- C35
- C36
- C37
- C48
- C57
- C58
- C80
- C82
- Clockspring (behind steering wheel, in steering column)
- Com dr driver
- Common
- Common dr drvr
- D25
- Defogger system
- Driver
- E17
- Evap temp sig
- F20
- Fbck signal
- Fuse 10a
- Fuse 30a
- Fuse b 40a
- Fuse e 40a
- Ground
- High blower mtr
- High blwr mtr
- High speed radiator fan relay
- Hot at all times
- Hot in run
- Hot in run or start
- Ignition
- Interior lights system
- Junction block (at left end of dash)
- K25
- Low blower mtr
- Low speed radiator fan relay
- M1 blower mtr
- M2 blower mtr
- Manual temperature control head
- Mode door actuator (on lower left side of hvac unit housing)
- Mode door driver
- Mode dr driver
- Mode fbck signal
- Mode fdbk sig
- Nca
- Panel lamps drvr
- Park lp rly out
- Pci bus
- Pk lp rly out
- Power distribution center (on left side of engine compartment)
- Powertrain control module (pcm) (in left rear of engine compartment)
- Radiator fan
- Rear wdo defog
- Rear window def
- Recirc dr driver
- Recirculation door actuator (on right side of hvac assembly)
- Red/tan
- Relay ctrl
- S106
- S117 (left inner fender)
- S125 (in power distribution center)
- S208
- S210
- S211
- S212
- S220
- S222
- Sens gnd
- Sensor gnd
- Sensor ground
- Signal
- Sound systems
- Tan
- Temp select
Automatic A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002
List of elements for Automatic A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002:
- (engine harness, front of engine)
- (engine harness, front of engine) s110
- (front of engine between coolant & camshaft sensors)
- (in power distribution center) s127
- (instrument panel center) s208
- (instrument pnk
- (left rear of engine, on block) g101
- (lower center of dash) g200
- (lower center of dash) g201
- A/c compressor clutch
- A/c compressor clutch relay
- A/c press sig
- A/c pressure transducer (in right front of engine compartment, on a/c discharge line)
- Ambient temperature sensor (at right side of headlamp mounting module grille opening)
- Aspirator motor
- Aspirator mtr dr
- Automatic temperature control head
- Battery
- Blnd dr driver
- Blnd dr fdbk sig
- Blower motor
- Blower motor power module (at lower right side of hvac assembly)
- Blower mtr ctrl
- Body control module (at left end of dash, attached to junction block)
- C10
- C12
- C18
- C24
- C26
- C27
- C28
- C32
- C33
- C34
- C35
- C36
- C37
- C38
- C56
- C57
- Clockspring (behind steering wheel, in steering column)
- Com dr driver
- D25
- Evap temp sig
- Evaporator temperature sensor (in hvac assembly, on face of evaporator)
- F20
- Fuse 10a
- Fuse 19 15a
- Fuse 21 10a
- Fuse 30a
- Ground
- Hot at all times
- Hot in run
- Hot in run or start
- Ignition
- In car temp sens
- In car temp sig
- Interior lights system
- Junction block (at left end of dash)
- K25
- Mode dr driver
- Mode dr fbck sig
- Nca
- Panel behind cluster) s204
- Panel lamps driver
- Pci bus
- Pnk
- Power distribution center (on left side of engine compartment)
- Powertrain control module (pcm) (in left rear of engine compartment)
- Pressure signal
- Recirc dr driver
- Red/tan
- Relay ctrl
- S104
- S106
- S117 (left inner fender)
- Sensor gnd
- Sensor ground
- Sensor signal
- Sun sens signal
- Sun sensor/ vtss led
Automatic A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002
List of elements for Automatic A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002:
- (a/c heater harness, near breakout to blend door actuator)
- (in power distribution center) s125
- (near right horn) g105
- (not used)
- 87a
- Blend air dr drvr
- Blend door actuator (on lower left side of hvac assembly)
- Common
- Common dr drvr
- Driver
- Fbck signal
- Fuse b 40a
- Fuse e 40a
- High speed radiator fan relay
- Hot at all times
- Low speed radiator fan relay
- Mode door actuator (on lower left side of hvac housing)
- Mode door driver
- Mode fbck signal
- Power distribution center (on left side of engine compartment)
- Radiator fan motor 1
- Radiator fan motor 2
- Radiator fan relay 1 (under center of radiator fan assembly)
- Radiator fan relay 2 (under center of radiator fan assembly)
- Recirculation door actuator (on right side of hvac assembly)
- Red
- S210
- S211
- S212
- Sensor gnd
- Sensor ground
3.5L
3.5L, Manual A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002
List of elements for 3.5L, Manual A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002:
- (engine harness, front of engine)
- (front of engine between coolant & camshaft sensors)
- (in breakout to a/c heater controls) s220
- (in power distribution center) s127
- (left rear of engine, on block) g114
- (lower center of dash) g206
- A/c compressor clutch
- A/c compressor clutch relay
- A/c led ind sig
- A/c mode mux
- A/c mode sw mux
- A/c press sig
- A/c pressure transducer (in right front of engine compartment, on a/c discharge line)
- Ambient temp
- Ambient temperature sensor (at right side of headlamp mounting module grille opening)
- Blnd dr driver
- Blnd dr fdbk
- Blower motor resistor block (on lower right side of hvac assembly)
- Body control module (at left end of dash, attached to junction block)
- C10
- C12
- C18
- C24
- C26
- C27
- C28
- C32
- C33
- C34
- C35
- C36
- C37
- C48
- C57
- C58
- C80
- C82
- Clockspring (behind steering wheel, in steering column)
- Com dr driver
- D25
- Defogger system
- E17
- Engine)
- Evap temp sig
- Evaporator temperature sensor (in hvac assembly, on face of evaporator)
- F20
- Fuse 10a
- Fuse 21 10a
- Fuse 30a
- Ground
- High blower mtr
- High blwr mtr
- Hot in run
- Hot in run or start
- Ignition
- Interior lights system
- Junction block (at left end of dash)
- K25
- Low blower mtr
- M1 blower mtr
- M2 blower mtr
- Manual temperature control head
- Mode dr driver
- Mode fdbk sig
- Nca
- Panel lamps drvr
- Park lp rly out
- Pci bus
- Pk lp rly out
- Power distribution center (on left side of engine compartment)
- Powertrain control module (pcm) (in left rear of engine compartment)
- Rear wdo defog
- Rear window def
- Recirc dr driver
- Red/tan
- Relay ctrl
- S104
- S106
- S117 (left inner fender)
- S208 (center of dash)
- S222
- Sensor gnd
- Sensor ground
- Signal
- Sound systems
- Tan
- Temp select
3.5L, Manual A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002
List of elements for 3.5L, Manual A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002:
- (a/c heater harness, near breakout to blend door actuator)
- (in power distribution center) s125
- (near right horn) g101
- (not used)
- 87a
- Blend air dr drvr
- Blend door actuator (on lower left side of hvac assembly)
- Common
- Common dr drvr
- Driver
- Fbck signal
- Fuse b 40a
- Fuse e 40a
- High speed radiator fan relay
- Hot at all times
- Low speed radiator fan relay
- Mode door actuator (on lower left side of hvac assembly)
- Mode door driver
- Mode fbck signal
- Power distribution center (on left side of engine compartment)
- Radiator fan motor 1
- Radiator fan motor 2
- Radiator fan relay 1 (under center of radiator fan assembly)
- Radiator fan relay 2 (under center of radiator fan assembly)
- Recirculation door actuator (on right side of hvac assembly)
- Red
- S210
- S211
- S212
- Sensor gnd
- Sensor ground
Automatic A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002
List of elements for Automatic A/C Wiring Diagram (1 of 2) for Dodge Intrepid SE 2002:
- (engine harness, front of engine)
- (engine harness, front of engine) s110
- (front of engine between coolant & camshaft sensors)
- (in power distribution center) s127
- (instrument panel center) s208
- (instrument pnk
- (left rear of engine, on block) g101
- (lower center of dash) g200
- (lower center of dash) g201
- A/c compressor clutch
- A/c compressor clutch relay
- A/c press sig
- A/c pressure transducer (in right front of engine compartment, on a/c discharge line)
- Ambient temperature sensor (at right side of headlamp mounting module grille opening)
- Aspirator motor
- Aspirator mtr dr
- Automatic temperature control head
- Battery
- Blnd dr driver
- Blnd dr fdbk sig
- Blower motor
- Blower motor power module (at lower right side of hvac assembly)
- Blower mtr ctrl
- Body control module (at left end of dash, attached to junction block)
- C10
- C12
- C18
- C24
- C26
- C27
- C28
- C32
- C33
- C34
- C35
- C36
- C37
- C38
- C56
- C57
- Clockspring (behind steering wheel, in steering column)
- Com dr driver
- D25
- Evap temp sig
- Evaporator temperature sensor (in hvac assembly, on face of evaporator)
- F20
- Fuse 10a
- Fuse 19 15a
- Fuse 21 10a
- Fuse 30a
- Ground
- Hot at all times
- Hot in run
- Hot in run or start
- Ignition
- In car temp sens
- In car temp sig
- Interior lights system
- Junction block (at left end of dash)
- K25
- Mode dr driver
- Mode dr fbck sig
- Nca
- Panel behind cluster) s204
- Panel lamps driver
- Pci bus
- Pnk
- Power distribution center (on left side of engine compartment)
- Powertrain control module (pcm) (in left rear of engine compartment)
- Pressure signal
- Recirc dr driver
- Red/tan
- Relay ctrl
- S104
- S106
- S117 (left inner fender)
- Sensor gnd
- Sensor ground
- Sensor signal
- Sun sens signal
- Sun sensor/ vtss led
Automatic A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002
List of elements for Automatic A/C Wiring Diagram (2 of 2) for Dodge Intrepid SE 2002:
- (a/c heater harness, near breakout to blend door actuator)
- (in power distribution center) s125
- (near right horn) g105
- (not used)
- 87a
- Blend air dr drvr
- Blend door actuator (on lower left side of hvac assembly)
- Common
- Common dr drvr
- Driver
- Fbck signal
- Fuse b 40a
- Fuse e 40a
- High speed radiator fan relay
- Hot at all times
- Low speed radiator fan relay
- Mode door actuator (on lower left side of hvac housing)
- Mode door driver
- Mode fbck signal
- Power distribution center (on left side of engine compartment)
- Radiator fan motor 1
- Radiator fan motor 2
- Radiator fan relay 1 (under center of radiator fan assembly)
- Radiator fan relay 2 (under center of radiator fan assembly)
- Recirculation door actuator (on right side of hvac assembly)
- Red
- S210
- S211
- S212
- Sensor gnd
- Sensor ground
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
