AIR CONDITIONING
5.7L
5.7L VIN R, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 5.7L VIN R, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near diode)
- 22 cm from ebcm breakout)
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse block)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c control
- A/c disable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c req
- A/c switch
- Blower switch
- Diode
- Fuse block
- G104 (top right side of cylinder head)
- G105 (right side of engine)
- Hot in run
- Hot in run or start
- Htr a/c fuse 12 25a
- Hvac control module
- Ign e fuse 10a
- Ignition
- Near egr valve breakout)
- Off
- Pnk
- S146 (eng harn, pnk
- S185
- S186
- S268 (i/p harn, behind center of dash)
- Sw sig
- Underhood fuse block
- Vehicle control module (left side of engine compt)
5.7L VIN R, Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind left
- (hvac harn, 8 cm from recirc door breakout) s244
- (i/p harn, 24 cm from i/p cluster breakout)
- (right side of dash) g202
- Air temp dr sensor
- Battery
- Blower fuse 3 50a
- Blower motor (under right side of dash)
- Blower resistor (on blower motor housing)
- Blower switch
- Defogger element
- Front mode door motor (on front a/c-heater housing)
- Front temperature door motor (on front a/c-heater housing)
- Fuse block
- G200
- Ground
- High blower relay (on top of front a/c- heater blower housing)
- Hot at all times
- Hot in run
- Htr-a/c fuse 12 25a
- Hvac control module
- Ignition
- Illumination
- Interior lights system
- Mode signal
- Off
- Rear defogger system
- Recirc ctrl
- Recirculation door motor (on front a/c-heater housing)
- Red
- S243 (hvac harn, 4 cm from recirc door breakout)
- S268 (i/p harness, behind center of dash)
- S298
- Side of dash)
- Tan
- Underhood fuse/relay center
5.7L VIN R, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near diode)
- (engine harness, 22 cm from ebcm breakout, 7.4l)
- (engine harness, near ebcm breakout)
- (engine harness, near egr valve breakout)
- (exc 4.3 l)
- (fwd lamps harn, 5 cm from right headlamp breakout)
- (hvac harness, 4 cm from recirc door breakout)
- (i/p harn, 28 cm from cluster breakout)
- (i/p harness, behind center of dash)
- (right side
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse/relay center)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c ctrl
- A/c disable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c req
- A/c switch
- Air temp dr sensor
- Aux fan fuse 30a
- Auxiliary cooling fan motor
- Auxiliary cooling fan relay (exc 4.3l) (in underhood fuse/relay center)
- Battery
- Blower fuse 3 50a
- Blower motor (under right side of dash)
- Blower resistor (on blower motor housing)
- Blower switch
- Defogger element
- Diode
- Front mode door motor (on front a/c-heater housing)
- Front temperature door motor (on front a/c-heater housing)
- Fuse block
- G104 (top right side of cylinder head)
- G105 (right side of engine)
- G112 (right front of engine compartment)
- G200 (behind left side of dash)
- G202
- Ground
- High blower relay (on top of front a/c-heater housing)
- Hot at all times
- Hot in run
- Hot in run or start
- Htr a/c fuse 12 25a
- Hvac control module
- Ign e fuse 10a
- Ignition
- Illumination
- Interior lights system
- Mode signal
- Of dash)
- Off
- Pnk
- Rear defogger system
- Recirc door signal
- Recirculation door motor (on front a/c-heater housing)
- Red
- Relay ctrl
- S103
- S110
- S128
- S146
- S185
- S186
- S212 (i/p harn, behind center of dash)
- S243
- S244 (hvac harn, 8 cm from recirc door breakout)
- S268
- S298
- Sw sig
- Tan
- Underhood fuse block
- Vehicle control module (left side of engine compt)
6.5L
6.5L VIN F, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near diode)
- 30 cm from ebcm breakout)
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse/relay center)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c control
- A/c disable
- A/c enable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c switch
- Blower switch
- Diode
- Fuse block
- G105 (right side of engine)
- Hot in run
- Hot in run or start
- Htr a/c fuse 12 25a
- Hvac control module
- Ign 1 fuse 10a
- Ignition
- Off
- Pnk
- Powertrain control module (behind right side of dash)
- Recirc signal
- Recirculation door motor (on a/c-heater housing)
- S185
- S186
- S268 (i/p harn, behind center of dash)
- Underhood fuse block
6.5L VIN F, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind right
- (engine harn,
- (engine harn, near diode)
- (engine harness, near ebcm breakout)
- (hvac harness, 4 cm from recirc door breakout)
- (hvac harness, 8 cm from recirc door breakout)
- (i/p harn, 24 cm from cluster breakout)
- (i/p harness, behind center of dash)
- (right side of dash) g202
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse center)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c ctrl
- A/c disable
- A/c enable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c switch
- Air temp dr signal
- Battery
- Block
- Blower fuse 3 50a
- Blower motor
- Blower resistor (under right side of dash, on heater housing)
- Blower switch
- Defogger element
- Diode
- Front mode door motor (on front a/c-heater housing)
- Front temperature door motor (on front a/c-heater housing)
- Fuse
- Fuse block
- G105 (right side of engine)
- G200 (behind left side of dash)
- Ground
- Heater and a/c control module
- High blower relay (under dash on top of heater-a/c housing)
- Hot at all times
- Hot in run
- Hot in run or start
- Htr-a/c fuse 12 25a
- Ign e fuse 10a
- Ignition
- Illumination
- Interior lights system
- Mode signal
- Near diode)
- Off
- Pnk
- Powertrain control module
- Rear defogger system
- Recirc signal
- Recirculation door motor (under dash on heater- a/c housing)
- Red
- S107 (engine harn, 30 cm from breakout to ebcm)
- S110
- S185
- S186
- S212 (i/p harn, behind center of dash)
- S243
- S244
- S268
- S298
- Side of dash)
- Tan
- Underhood
7.4L
7.4L VIN J, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Compressor Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near diode)
- 22 cm from ebcm breakout)
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse block)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c control
- A/c disable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c req
- A/c switch
- Blower switch
- Diode
- Fuse block
- G104 (top right side of cylinder head)
- G105 (right side of engine)
- Hot in run
- Hot in run or start
- Htr a/c fuse 12 25a
- Hvac control module
- Ign e fuse 10a
- Ignition
- Near egr valve breakout)
- Off
- Pnk
- S146 (eng harn, pnk
- S185
- S186
- S268 (i/p harn, behind center of dash)
- Sw sig
- Underhood fuse block
- Vehicle control module (left side of engine compt)
7.4L VIN J, Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind left
- (hvac harn, 8 cm from recirc door breakout) s244
- (i/p harn, 24 cm from i/p cluster breakout)
- (right side of dash) g202
- Air temp dr sensor
- Battery
- Blower fuse 3 50a
- Blower motor (under right side of dash)
- Blower resistor (on blower motor housing)
- Blower switch
- Defogger element
- Front mode door motor (on front a/c-heater housing)
- Front temperature door motor (on front a/c-heater housing)
- Fuse block
- G200
- Ground
- High blower relay (on top of front a/c- heater blower housing)
- Hot at all times
- Hot in run
- Htr-a/c fuse 12 25a
- Hvac control module
- Ignition
- Illumination
- Interior lights system
- Mode signal
- Off
- Rear defogger system
- Recirc ctrl
- Recirculation door motor (on front a/c-heater housing)
- Red
- S243 (hvac harn, 4 cm from recirc door breakout)
- S268 (i/p harness, behind center of dash)
- S298
- Side of dash)
- Tan
- Underhood fuse/relay center
7.4L VIN J, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Manual A/C Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near diode)
- (engine harness, 22 cm from ebcm breakout, 7.4l)
- (engine harness, near ebcm breakout)
- (engine harness, near egr valve breakout)
- (exc 4.3 l)
- (fwd lamps harn, 5 cm from right headlamp breakout)
- (hvac harness, 4 cm from recirc door breakout)
- (i/p harn, 28 cm from cluster breakout)
- (i/p harness, behind center of dash)
- (right side
- A/c comp fuse 10a
- A/c compressor clutch
- A/c compressor clutch relay (in underhood fuse/relay center)
- A/c compressor cycling switch (in low pressure line, on accumulator)
- A/c ctrl
- A/c disable
- A/c high pressure cutout switch (on a/c compressor)
- A/c low pressure cutout switch (on a/c compressor)
- A/c req
- A/c switch
- Air temp dr sensor
- Aux fan fuse 30a
- Auxiliary cooling fan motor
- Auxiliary cooling fan relay (exc 4.3l) (in underhood fuse/relay center)
- Battery
- Blower fuse 3 50a
- Blower motor (under right side of dash)
- Blower resistor (on blower motor housing)
- Blower switch
- Defogger element
- Diode
- Front mode door motor (on front a/c-heater housing)
- Front temperature door motor (on front a/c-heater housing)
- Fuse block
- G104 (top right side of cylinder head)
- G105 (right side of engine)
- G112 (right front of engine compartment)
- G200 (behind left side of dash)
- G202
- Ground
- High blower relay (on top of front a/c-heater housing)
- Hot at all times
- Hot in run
- Hot in run or start
- Htr a/c fuse 12 25a
- Hvac control module
- Ign e fuse 10a
- Ignition
- Illumination
- Interior lights system
- Mode signal
- Of dash)
- Off
- Pnk
- Rear defogger system
- Recirc door signal
- Recirculation door motor (on front a/c-heater housing)
- Red
- Relay ctrl
- S103
- S110
- S128
- S146
- S185
- S186
- S212 (i/p harn, behind center of dash)
- S243
- S244 (hvac harn, 8 cm from recirc door breakout)
- S268
- S298
- Sw sig
- Tan
- Underhood fuse block
- Vehicle control module (left side of engine compt)
ANTI-LOCK BRAKES
5.7L
5.7L VIN R, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near ebcm breakout) s111
- (selectable 4wd harn, near breakout to transfer case relay)
- 4wd sw input
- Abs fuse 60a
- Abs ind
- Abs ind ground
- Battery
- Brake fuse 18 10a
- Brake ind
- Brake ind input
- Brake lamp ind out
- Brake pressure warning switch (underside of ebcm)
- Brake sw input
- Brake sw output
- Data link connector (dlc) (left of steering column)
- Daytime running lamp (drl) module (behind left side of dash)
- Ebcm ground
- Electronic brake control module (left side of engine compt)
- Electronic variable orifice (evo)/ passlock control module (under center of dash)
- Engine controls system
- Front axle actuator (on right rear of front drive axle)
- Fuse/relay block (left rear of engine compt)
- G119 (right front of eng block)
- Gauges fuse 4 10a
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition
- Instrument cluster
- Left front wheel speed sensor
- M/t
- Pnk
- Pump motor ground
- Red
- Right front wheel speed sensor
- S107
- S147
- S150 (engine harn, approx 13 cm from ebcm breakout)
- S151
- S152
- S213
- S280 (i/p harn, approx 5 cm from dlc breakout)
- S314
- Sensor high
- Sensor low
- Serial data
- Serial data line
- Stoplamp switch (top of brake pedal)
- Tan
- Transfer case control module (on steering column support bracket)
- Transmissions system
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (vss) (left side of transmission/ transfer case)
- Vehicle speed sig
- Vss (+)
- Vss (-)
- Vss sig
6.5L
6.5L VIN F, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500:
- (behind right side of dash) vehicle speed sensor buffer
- 4wd sw input
- Abs fuse 60a
- Abs ind
- Abs ind ground
- Battery
- Brake fuse 18 10a
- Brake ind
- Brake ind input
- Brake lamp ind out
- Brake pressure warning switch (underside of ebcm)
- Brake sw input
- Data link connector (dlc) (left of steering column)
- Daytime running lamp (drl) module (behind left side of dash)
- Ebcm ground
- Electronic brake control module (left side of engine compt)
- Electronic variable orifice (evo)/ passlock control module (under center of dash)
- Engine controls system
- Front axle actuator (on right rear of front drive axle)
- Fuse/relay block (left rear of engine compt)
- G119 (right front of eng block)
- Gauges fuse 4 10a
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition
- Instrument cluster
- Left front wheel speed sensor
- M/t
- Pnk
- Powertrain control module (pcm) (behind right side of dash)
- Pump motor ground
- Red
- Right front wheel speed sensor
- S107
- S150 (engine harn, approx 13 cm from ebcm breakout)
- S151
- S152
- S213
- S280 (i/p harn, approx 5 cm from dlc breakout)
- S314 (selectable 4wd harn, near breakout to transfer case relay)
- Sensor high
- Sensor low
- Serial data
- Serial data line
- Stoplamp switch (top of brake pedal)
- Tan
- Transfer case control module (on steering column support bracket)
- Transmissions system
- Vss out
- Vss sig
7.4L
7.4L VIN J, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Anti-lock Brake Wiring Diagrams for Chevrolet Cab & Chassis C2000 2500:
- (engine harn, near ebcm breakout) s111
- (selectable 4wd harn, near breakout to transfer case relay)
- 4wd sw input
- Abs fuse 60a
- Abs ind
- Abs ind ground
- Battery
- Brake fuse 18 10a
- Brake ind
- Brake ind input
- Brake lamp ind out
- Brake pressure warning switch (underside of ebcm)
- Brake sw input
- Brake sw output
- Data link connector (dlc) (left of steering column)
- Daytime running lamp (drl) module (behind left side of dash)
- Ebcm ground
- Electronic brake control module (left side of engine compt)
- Electronic variable orifice (evo)/ passlock control module (under center of dash)
- Engine controls system
- Front axle actuator (on right rear of front drive axle)
- Fuse/relay block (left rear of engine compt)
- G119 (right front of eng block)
- Gauges fuse 4 10a
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition
- Instrument cluster
- Left front wheel speed sensor
- M/t
- Pnk
- Pump motor ground
- Red
- Right front wheel speed sensor
- S107
- S147
- S150 (engine harn, approx 13 cm from ebcm breakout)
- S151
- S152
- S213
- S280 (i/p harn, approx 5 cm from dlc breakout)
- S314
- Sensor high
- Sensor low
- Serial data
- Serial data line
- Stoplamp switch (top of brake pedal)
- Tan
- Transfer case control module (on steering column support bracket)
- Transmissions system
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (vss) (left side of transmission/ transfer case)
- Vehicle speed sig
- Vss (+)
- Vss (-)
- Vss sig
ANTI-THEFT
Forced Entry Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Forced Entry Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (right side of dash) g201
- Body control module (in center console)
- C16
- Cargo door jamb switch
- Ctsy fuse 3 20a
- D11
- D12
- D13
- D14
- Door lock
- Door lock inversion module (behind left side of dash)
- Door unlock
- Ex lights ctrl
- G201 (right side of dash)
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- Grd
- Hatch ajar sw
- Headlight system
- Horn rly ctrl
- Horns system
- Hot at all times
- I/p fuse block
- Left front door jamb switch
- Left rear door jamb switch
- Lf dr ajar sw
- Liftgate jamb switch
- Rf dr ajar sw
- Right front door jamb switch
- Right rear door jamb switch
- S204
- S218
- S262 (crossbody harn, approx 22 cm from seat belt breakout)
- S330
- S335
- S336
- S410
- Sec led ctrl
- Security led (in center of floor console)
- Shock
- Shock sensor
- Shock sensor (in center console)
- Tamper
- Tan
Pass-Key Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Pass-Key Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (dash harn, 5 cm from dlc breakout) s280
- 12v ref
- 5 volt ref
- Capacitor 0.47mf
- Data link connector (under left side of dash)
- Electronic power steering system
- Engine controls system
- Evo sol fd
- Evo sol out
- Evo/passlock module (under center of dash)
- Filter (molded in steering column harness)
- G134 (diesel: front top of engine, gas: right top center of cylinder head)
- Gauges fuse 4 10a
- Grd
- Hot at all times
- Hot in run or start
- I/p fuse block
- Ign
- Instrument cluster
- Nca
- Passlck sig
- Passlock sensor (internal to steering column)
- Passlock signal
- Pnk
- Resistor 10 ohms
- S213
- S215
- Sec ind out
- Security fuse 21 10a
- Security indicator
- Sens ret
- Sensor grd
- Serial data
- Steering handwheel speed sensor (sensor ground)
- Vss
- Whl pos sig
COMPUTER DATA LINES
Computer Data Lines for Chevrolet Cab & Chassis C2000 2500
List of elements for Computer Data Lines for Chevrolet Cab & Chassis C2000 2500:
- (diesel) g134 (front to of engine)
- (right front of eng, near thermostat housing) (gas) g131
- 13 cm from ebcm breakout)
- Automatic transfer case control module (behind left side of dash)
- Aux pwr fuse 7 25a
- Data clss
- Data clss 2
- Data link connector (dlc) (under left side of dash, left of steering column)
- Diag enable
- Diesel
- Electronic brake control module (ebcm) (on left side of engine compt)
- Electronic variable orifice/passlock control module (under center of dash)
- Except luxury
- G202 (behind left side of dash)
- Gasoline
- Hot at all times
- I/p fuse block
- Inflatable restraint sensing & diagnostic module (under driver's seat carpet)
- Powertrain control module (pcm) (behind right side of dash, near blower motor)
- Prog enable
- Radio
- Remote control door lock receiver (behind center of dash)
- S204
- S215
- S245
- S272
- S280 (dash harness, approx 5 cm from dlc breakout)
- S294
- Serial data
- Tan
- Transfer case control module (tccm) (under dash, on steering column support bracket)
- Uart data
- Vehicle control module (vcm) (on left side of engine compt)
- Vehicle interface unit
COOLING FAN
Cooling Fan Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Cooling Fan Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (fwd lamps harn, 5 cm from right headlamp breakout)
- (in underhood fuse/relay center)
- A/c comp fuse 10a
- Aux fan fuse 30a
- Auxiliary cooling fan motor
- Auxiliary cooling fan relay
- G112 (right front of engine compartment)
- Hot at all times
- Hot in run or start
- Red
- Relay ctrl
- S128
- Underhood fuse block
- Vehicle control module (left rear of engine compt)
CRUISE CONTROL
5.7L
5.7L VIN R, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (i/p harn, 20 cm from heater/ a/c breakout) s222
- (i/p harn, left rear of engine compt)
- A/t
- A12
- A13
- A14
- A15
- Brake fuse 18 10a
- Clutch pedal position switch (top of clutch pedal)
- Cruise control module (left rear of engine compartment)
- Cruise control switch
- Cruise engage input
- Cruise fuse 6 10a
- Cruise on input
- Engine control system
- Exterior light system
- G119 (right front of engine, near thermostat housing)
- Ground
- Hot at all times
- Hot in run
- I/p fuse block (left side of dash)
- Ignition
- M/t
- Off
- R/a
- Resume/accel sig
- S/c
- S153
- S215
- S220 (i/p harness, 6 cm from steering column harness breakout)
- S221 (i/p harn, 20 cm from cluster breakout)
- S299
- Set/coast sig
- Shift inter- lock system
- Speed sensor input
- Speed sensor output
- Stop/haz fuse 1 20a
- Stoplamp or clutch sw input
- Stoplamp sw input
- Stoplamp switch (top of brake pedal)
- Vcm signal
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (vss) (left side of transmission)
- Vss high
- Vss low
6.5L
6.5L VIN F, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind right side of dash)
- (behind right side of dash) powertrain control module (pcm)
- (i/p harn, 6 cm from steering column breakout) s220
- A/t
- A11
- A12
- A13
- A14
- A15
- Antilock brake system
- B10
- B11
- Brake fuse 18 10a
- Clutch pedal position switch (top of clutch pedal)
- Cruise control switch
- Cruise fuse 6 10a
- Cruise on input
- D10
- Engine control system
- Exterior light system
- Hot at all times
- Hot in run
- I/p fuse block (under left side of dash)
- M/t
- Off
- R/a
- Resume/accel sig
- S/c
- S152 (eng harn, 4 cm from i/p harn breakout)
- S211
- S220
- S222 (i/p harn, 20 cm from inflatable restraint switch breakout)
- S299
- Set/coast sig
- Stop/haz fuse 1 20a
- Stoplamp switch (top of brake pedal)
- Stoplamp switch input
- Stoplamp/ clutch switch input
- Vehicle speed sensor (vss) (left side of transmission)
- Vehicle speed sensor buffer
- Vss high
- Vss input
- Vss low
- Vss output
7.4L
7.4L VIN J, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Cruise Control Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (i/p harn, 20 cm from heater/ a/c breakout) s222
- (i/p harn, left rear of engine compt)
- A/t
- A12
- A13
- A14
- A15
- Brake fuse 18 10a
- Clutch pedal position switch (top of clutch pedal)
- Cruise control module (left rear of engine compartment)
- Cruise control switch
- Cruise engage input
- Cruise fuse 6 10a
- Cruise on input
- Engine control system
- Exterior light system
- G119 (right front of engine, near thermostat housing)
- Ground
- Hot at all times
- Hot in run
- I/p fuse block (left side of dash)
- Ignition
- M/t
- Off
- R/a
- Resume/accel sig
- S/c
- S153
- S215
- S220 (i/p harness, 6 cm from steering column harness breakout)
- S221 (i/p harn, 20 cm from cluster breakout)
- S299
- Set/coast sig
- Shift inter- lock system
- Speed sensor input
- Speed sensor output
- Stop/haz fuse 1 20a
- Stoplamp or clutch sw input
- Stoplamp sw input
- Stoplamp switch (top of brake pedal)
- Vcm signal
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (vss) (left side of transmission)
- Vss high
- Vss low
DEFOGGERS
Defogger Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Defogger Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (w/ heated mirrors)
- C222
- Convenience center (under left side of dash)
- Fuse/relay block (left rear of engine compt)
- G201 (right side of dash)
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- G905 (right "c" pillar)
- Heated mirror relay (behind left side of dash, above support bracket)
- Hot in run
- Hot in run or start
- Htr-a/c fuse 12 25a
- Hvac control module (in center of dash)
- I/p fuse block (under left side of dash)
- Left cargo door contactor
- Left heated mirror
- Left power outside rear view mirror
- Left rear cargo door defogger grid
- Mirrors fuse 10a
- Pick-up w/ extended or crew cab
- Rear window defogger grid
- Rear window defogger switch
- Right cargo door contactor
- Right heated mirror
- Right rear cargo door defogger grid
- Rr-defog fuse 30a
- S218
- S223
- S251
- S259
- S268
- S410
- S425
- S506 (inside power outside rear view mirror harn., 7 cm from power outside rear view mirror)
- Solid state time delay relay
- Suburban/utility w/ liftgate
- Suburban/utility w/o liftgate
ELECTRONIC POWER STEERING
Electronic Power Steering Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Electronic Power Steering Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (front top of engine) g134 (2000)
- (i/p harness, approximately 40 cm from instrument cluster breakout)
- (i/p harness, approximately 5 cm from dlc breakout)
- (right front of engine) g119
- (right rear of engine)
- 5 volt ref
- Battery
- Data
- Data link connector (dlc) (under left side of dash, left of steering column)
- Diesel
- Electronic variable orifice (evo)/ passlock module (under center of dash)
- Evo feed
- Evo solenoid out
- G117 (1999)
- Gas
- Gauges fuse 4 10a
- Ground
- Hot at all times
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition
- Pnk
- S213
- S215
- S221
- S280
- Security/strg fuse 21 20a
- Sensor return
- Steering assist control solenoid (part of power steering pump)
- Steering handwheel speed sensor (on steering column, near firewall)
- Steering wheel posit signal
- Sws posit sig
- Vehicle control module (on left side of engine compartment)
- Vehicle speed sensor buffer (behind right side of dash)
- Volt ref
- Vss sig out
- Vss signal input
ENGINE PERFORMANCE
5.7L
5.7L VIN K, Engine Performance Wiring Diagrams (1 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (1 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (attached to right rear of throttle body) idle air control (iac) valve
- (bottom front of engine near, crank pulley) crankshaft position sensor
- (eng harn, 13 cm from fuse/relay center)
- (eng harn, 13 cm from starter solenoid breakout)
- (eng harn, 20 cm from fuse/relay center)
- (eng harn, 6.5 cm from cps breakout)
- (eng harn, 6.5 cm from starter solenoid breakout)
- (engine harn, 17 cm from under- hood fuse/relay center nreakout)
- (top right side of engine) evaporative emission canister purge solenoid valve
- 1-2 shift sol ctrl
- 2-3 shift sol ctrl
- 3-2 shift sol ctrl
- A/t w/ 4wd
- Air pump rel ctrl
- Cam posit sens sig
- Camshaft position sensor (inside distributor)
- Crank posit sens sig
- Ect sens sig
- Egr posit sig
- Fuel gauge lvl
- Fuel tank press sens
- G119 (right front of engine block)
- Heated oxygen sensor (bank 1 sensor 1) (in left exhaust pipe, in front of catalytic converter)
- Heated oxygen sensor (bank 2 sensor 1) (in right exhaust pipe, in front of catalytic converter)
- Heated oxygen sensor (below 8600 gvw: bank 1 sensor 2) (left exhaust pipe, behind catalytic converter (over 8600 gvw: bank 2 sensor 2) (right exhaust pipe, behind catalytic converter)
- Ho2s low
- Ho2s sig
- Iat sens sig
- Idle air ctrl (iac) a hi
- Idle air ctrl (iac) b lo
- Ign feed
- Inj 1 ctrl
- Inj 2 ctrl
- Inj 3 ctrl
- Inj 4 ctrl
- Inj 5 ctrl
- Inj 6 ctrl
- Inj 7 ctrl
- Inj 8 ctrl
- Inline gender adapter a
- Knock sens sig
- Knock sensor (ks) (right side of engine block, below exhaust manifold, forward of starter)
- Low ref
- Map sens input
- Mass air flow sens sig
- Nca
- Others
- Pnk
- Pnk c ignition feed
- S012
- S013
- S016
- S021
- S022
- S031
- S148
- S149
- S162
- Sens rtn
- Sens sig
- Sensor return
- Tan
- Tcc pwm sol ctrl
- Tcc sol ctrl
- Temp sens input
- Throttle posit sens
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (left side of transmission, left side of transfer case w/ 4wd)
- Vent ctlr
- Vss sig
- Vss signal
5.7L VIN K, Engine Performance Wiring Diagrams (2 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (2 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (eng harn, 14 cm from thermostat ground stud breakout)
- (left front corner of eng compt) g100
- A 2-3 shift red
- A 3-2 shift solenoid
- A nca
- Air injection reaction pump motor (left front of eng compt)
- Air injection reaction pump relay (california) (underhood fuse/ relay center)
- Automatic transmission
- Automatic transmission fluid pressure (tfp) manual valve position switch
- Aux-b fuse 30a stud-b
- Ecm1 fuse 20a
- Eng1 k7
- Evaporative emissions (evap) canister vent valve (left side of engine compt)
- Exhaust gas recirculation (egr) valve (front of engine near thermostat housing)
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuse 20a l8
- Heated oxygen sensor (below 8600 gvw: bank 2 sensor 2) (right exhaust pipe, behind catalytic converter) (over 8600 gvw: bank 1 sensor 2) (left exhaust pipe behind catalytic converter)
- Hot at all times
- Hot in run & start
- Nca
- Pnk
- Pnk a
- Pressure control solenoid valve
- Red
- S018
- S104 pnk a
- S108
- S161
- S166 (eng harn, 18 cm from ebcm breakout)
- S167
- Solenoid
- Solenoid check valve
- Tan
- Tcc solenoid
- Torque converter red clutch pulse width modulation solenoid
- Trans fluid temperature sensor
- Under hood fuse/relay center
5.7L VIN K, Engine Performance Wiring Diagrams (3 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (3 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (af harness, 10 cm from hpl conn)
- (eng harn, 10 cm from thermostat ground stud breakout)
- (eng harn, 13 cm from cps breakout)
- (eng harn, 4 cm from fuse/relay center)
- (eng harn, near underhood lamp conn breakout)
- (produc- tion use)
- +5v ref
- 1x cam sens
- 4x crank in
- Actual gas
- Af ecu bat
- Af ecu gnd
- Af ecu ign
- Alternative fuel engine control unit (left side of engine compt)
- C001
- C002
- Class 2 data
- Cng fuse 20a
- Ect input
- Egr sens
- F pmp rly
- Fps +5v
- Fps sig
- Fps/fts gnd
- Fts sig
- Fuel lev out
- Fuel pressure sensor (end of cng fuel tank)
- Fuel temperature sensor (end of cng fuel tank)
- G119 (right front of engine)
- Gas flow out
- Gauge sel sw
- Hi pres lo
- Ho2s in
- Hot at all times
- Hot in run, bulb test and start
- Iat input
- Ign e fuse 10a
- Ind ctrl
- Low pres lo
- Maf input
- Map input
- Mil ctrl
- Mil out
- Ngo enable
- Pnk
- Red
- Relay ctrl
- S001
- S002
- S009
- S014
- S015
- S017
- S019
- S020
- S399
- Sensor gnd
- Serial data
- Tan
- Tp sensor
- Under hood fuse/relay center
- Vss input
5.7L VIN K, Engine Performance Wiring Diagrams (4 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (4 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (af harn, 32.5 cm from relay breakout)
- (af harn, near lpl breakout)
- Af d1 (af harn 10 cm from hpl conn)
- Af d2 (af harn 10 cm from lpl conn)
- Af fuel pump relay (left of engine compt)
- Fuel gauge relay (left of engine compt)
- Fuel gauge select switch
- G119 (right front of engine)
- Gas mass sensor (right front of engine)
- High pressure lock-off solenoid (end of cng fuel tank)
- Ignition relay (left of engine compt)
- Interior lights system
- Lock-off relay (left of engine compt)
- Low pressure lock-off solenoid (right middle of engine)
- Mixture control valve motor (right front of engine)
- Nca
- Pnk
- Red
- S003 (af harn, 22.5 cm from relay breakout)
- S004
- S005 (af harn, 13 cm from conn breakout)
- S009
- S010
- S011
- S398 (af harn, near breakout to hpl conn)
- S399
- Tan
5.7L VIN K, Engine Performance Wiring Diagrams (5 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (5 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (eng harn, approx 17 cm from breakout to egr valve) s106
- (eng harn, hd: 10 cm from egr valve breakout, ld: 27 cm from egr valve breakout)
- (engine harn, approx 16 cm from breakout to egr valve)
- (inside left frame rail, near rear crossmember)
- (right rear of cylinder head) g117
- (taillamp extension harn, 6 cm from the fuel pump harn breakout)
- Automatic transmission input shaft speed sensor (left side of transmission)
- C100
- C223
- Convenience center (under left side of dash)
- Engine coolant temperature sensor (top right front of engine, near thermostat housing)
- Fuel gauge input
- Fuel pump & sender (in fuel tank)
- Fuel tank pressure sensor (in fuel tank)
- G415
- Gauges fuse 4 10a
- Grd
- Hot in off, run or start
- Hot in run or start
- I/p fuse block
- Ign
- Instrument cluster
- Intake air temperature sensor (in air intake duct)
- M/t only
- Manifold absolute pressure (map) sensor (top right of engine, near fuel injectors)
- Mass airflow sensor (in air intake duct)
- Pnk
- Red
- S103
- S131
- S213
- S231
- S232
- S430
- Service engine soon indicator
- Sig
- Speedometer input
- Tachometer input
- Tan
- Tan a
- Throttle position sensor (on throttle body assembly)
- Trans fuse 20 10a
- Upshift lamp
- W/o dual fuel tank
5.7L VIN K, Engine Performance Wiring Diagrams (6 of 6) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, Engine Performance Wiring Diagrams (6 of 6) for Chevrolet Cab & Chassis C2000 2500:
- (engine harness, approx 13 cm from ebcm breakout) s150
- (engine harness, approx 7 cm from ebcm breakout)
- (i/p harn, 20 cm from inflatable restraint switch breakout)
- (i/p harn, harness, 13 cm from left engine grommet)
- (i/p harness, approx 40 cm from instrument cluster breakout)
- (or
- (right rear of cylinder head) g120
- 4wd input
- 5v ref voltage
- 87a
- A pnk
- A/c comp enable rel
- A/c request signal
- A/t
- Air conditioning system
- Air inlet vlv mtr ctlr
- Automatic 4wd
- Automatic transfer case shift controller
- Aux fan relay
- Brake sw input
- Brake switch input
- Check eng lp ctrl
- Clutch pedal position (cpp) switch (at top of clutch pedal bracket)
- Cooling fans system
- Cpp sw input
- Cruise control module (left rear of engine compt, on firewall)
- Cruise ctrl sig eng
- Data link connector (under left side of dash, left side of steering column)
- Distributor
- Egr vlv feed
- Egr vlv ground
- Electronic brake control module (ebcm) (on left side of engine compt)
- Electronic variable orifice/ passlock control module (center of dash)
- Est output sig
- Evap can purge vlv
- F11 ecmb fuse 20a
- Force motor feed
- Force motor return
- Four whl dr sig
- Four whl dr sig lo
- Fuel level input
- Fuel pump a prime connector (left rear of eng compt)
- Fuel pump relay
- Fuel pump rly ctrl
- G117 (right rear of cylinder head)
- G12
- Ground
- High voltage coil wire
- Hot at all times
- Hot in run
- I/p fuse block
- Ign coil out
- Ign input
- Ign timing sig.
- Ignition
- Ignition coil (top right rear of engine)
- Ignition control module (right side rear of engine)
- Ignition feed
- M/t
- M4 brake fuse 18 10a n3
- Manual or selectable 4wd
- Ngo input
- Pnk
- Pressure switch input
- Radio
- Red
- S101
- S103
- S111 (engine harness, approx 10 cm from ebcm breakout)
- S151
- S152
- S153
- S221
- Sensor ground
- Sensor return
- Serial data sig
- Shift ind lp out
- Speed sensor
- Speed sensor input
- Stoplamp switch (top of brake pedal)
- Stoplamp/ clutch switch input
- Switch signal
- Trans input speed rtn
- Trans input speed sig
- Transfer case control module (under dash, on steering column support bracket)
- Transfer case switch (left top of transfer case)
- Transmissions system
- Underhood fuse/ relay center
- Vcm sig
- Vehicle control module (vcm) (left side of engine compt)
- Vss input
- Vss sig out
5.7L VIN R, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (attached to right rear of throttle body) idle air control (iac) valve
- (bottom front of engine near, crank pulley) crankshaft position sensor
- (top right side of engine) evaporative emission canister purge solenoid valve
- 1-2 shift sol ctrl
- 2-3 shift sol ctrl
- 3-2 shift sol ctrl
- A/t w/ 4wd
- Air pump rel ctrl
- Cam posit sens sig
- Camshaft position sensor (inside distributor)
- Crank posit sens sig
- Ect sens sig
- Egr posit sig
- Fuel gauge lvl
- Fuel tank press sens
- G119 (right front of engine block)
- Heated oxygen sensor (bank 1 sensor 1) (in left exhaust pipe, in front of catalytic converter)
- Heated oxygen sensor (bank 2 sensor 1) (in right exhaust pipe, in front of catalytic converter)
- Heated oxygen sensor (below 8600 gvw: bank 1 sensor 2) (left exhaust pipe, behind catalytic converter (over 8600 gvw: bank 2 sensor 2) (right exhaust pipe, behind catalytic converter)
- Ho2s low
- Ho2s sig
- Iat sens sig
- Idle air ctrl (iac) a hi
- Idle air ctrl (iac) b lo
- Ign feed
- Inj 1 ctrl
- Inj 2 ctrl
- Inj 3 ctrl
- Inj 4 ctrl
- Inj 5 ctrl
- Inj 6 ctrl
- Inj 7 ctrl
- Inj 8 ctrl
- Inline gender adapter a
- Knock sens sig
- Knock sensor (ks) (right side of engine block, below exhaust manifold, forward of starter)
- Low ref
- Map sens input
- Mass air flow sens sig
- Nca
- Others
- Pnk
- Pnk c ignition feed
- Pnk pnk
- S148
- S149
- S162
- Sens rtn
- Sens sig
- Sensor return
- Tan
- Tcc pwm sol ctrl
- Tcc sol ctrl
- Temp sens input
- Throttle posit sens
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (left side of transmission, left side of transfer case w/ 4wd)
- Vent ctlr
- Vss sig
- Vss signal
5.7L VIN R, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (left front corner of eng compt) g100
- A 2-3 shift red
- A 3-2 shift solenoid
- A nca
- Air injection reaction pump motor (left front of eng compt)
- Air injection reaction pump relay (california) (underhood fuse/ relay center)
- Automatic transmission
- Automatic transmission fluid pressure (tfp) manual valve position switch
- Aux-b fuse 30a stud-b
- Ecm1 fuse 20a
- Eng1 k7
- Evaporative emissions (evap) canister vent valve (left side of engine compt)
- Exhaust gas recirculation (egr) valve (front of engine near thermostat housing)
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuse 20a l8
- Heated oxygen sensor (below 8600 gvw: bank 2 sensor 2) (right exhaust pipe, behind catalytic converter) (over 8600 gvw: bank 1 sensor 2) (left exhaust pipe behind catalytic converter)
- Hot at all times
- Hot in run & start
- Nca
- Pnk
- Pnk pnk pnk tan red
- Pressure control solenoid valve
- Red
- S104
- S108
- S161
- S166 (eng harn, 18 cm from ebcm breakout)
- S167
- Solenoid
- Solenoid check valve
- Tan
- Tcc solenoid
- Torque converter red clutch pulse width modulation solenoid
- Trans fluid temperature sensor
- Under hood fuse/relay center
5.7L VIN R, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (eng harn, approx 17 cm from breakout to egr valve) s106
- (eng harn, hd: 10 cm from egr valve breakout, ld: 27 cm from egr valve breakout)
- (engine harn, approx 16 cm from breakout to egr valve)
- (inside left frame rail, near rear crossmember)
- (right rear of cylinder head) g117
- (taillamp extension harn, 6 cm from the fuel pump harn breakout)
- Automatic transmission input shaft speed sensor (left side of transmission)
- C100
- C223
- Convenience center (under left side of dash)
- Engine coolant temperature sensor (top right front of engine, near thermostat housing)
- Fuel gauge input
- Fuel pump & sender (in fuel tank)
- Fuel tank pressure sensor (in fuel tank)
- G415
- Gauges fuse 4 10a
- Grd
- Hot in off, run or start
- Hot in run or start
- I/p fuse block
- Ign
- Input
- Instrument cluster
- Intake air temperature sensor (in air intake duct)
- M/t only
- Manifold absolute pressure (map) sensor (top right of engine, near fuel injectors)
- Mass airflow sensor (in air intake duct)
- Pnk
- Pnk pnk tan red
- S103
- S213
- S231
- S232
- S430
- Service engine soon indicator
- Sig
- Speedometer input
- Tachometer
- Tan a
- Throttle position sensor (on throttle body assembly)
- Trans fuse 20 10a
- Upshift lamp
- W/o dual fuel tank
5.7L VIN R, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (engine harness, approx 13 cm from s150
- (engine harness, approx 7 cm from ebcm breakout)
- (i/p harn, 20 cm from inflatable restraint switch breakout)
- (i/p harn, harness, 13 cm from left engine grommet)
- (i/p harness, approx 40 cm from instrument cluster breakout)
- (or
- (right rear of cylinder head) g120
- 4wd input
- 5v ref voltage
- 87a
- A pnk
- A/c comp enable rel
- A/c request signal
- A/t
- Air conditioning system
- Air inlet vlv mtr ctlr
- Automatic 4wd
- Automatic transfer case shift controller
- Aux fan relay
- Brake sw input
- Brake switch input
- Check eng lp ctrl
- Clutch pedal position (cpp) switch (at top of clutch pedal bracket)
- Cooling fans system
- Cpp sw input
- Cruise control module (left rear of engine compt, on firewall)
- Cruise ctrl sig eng
- Data link connector (under left side of dash, left side of steering column)
- Distributor
- Ebcm breakout)
- Egr vlv feed
- Egr vlv ground
- Electronic brake control module (ebcm) (on left side of engine compt)
- Electronic variable orifice/ passlock control module (center of dash)
- Est output sig
- Evap can purge vlv
- F11 ecmb fuse 20a
- Force motor feed
- Force motor return
- Four whl dr sig
- Four whl dr sig lo
- Fuel level input
- Fuel pump a prime connector (left rear of eng compt)
- Fuel pump relay
- Fuel pump rly ctrl
- G117 (right rear of cylinder head)
- G12
- Ground
- High voltage coil wire
- Hot at all times
- Hot in run
- I/p fuse block
- Ign coil out
- Ign input
- Ign timing sig.
- Ignition
- Ignition coil (top right rear of engine)
- Ignition control module (right side rear of engine)
- Ignition feed
- M/t
- M4 brake fuse 18 10a n3
- Manual or selectable 4wd
- Pnk
- Pressure switch input
- Radio
- Red
- S101
- S103
- S111 (engine harness, approx 10 cm from ebcm breakout)
- S151
- S152
- S153
- S221
- Sensor ground
- Sensor return
- Serial data sig
- Shift ind lp out
- Speed sensor
- Speed sensor input
- Stoplamp switch (top of brake pedal)
- Stoplamp/ clutch switch input
- Switch signal
- Trans input speed rtn
- Trans input speed sig
- Transfer case control module (under dash, on steering column support bracket)
- Transfer case switch (left top of transfer case)
- Transmissions system
- Underhood fuse/ relay center
- Vcm sig
- Vehicle control module (vcm) (left side of engine compt)
- Vss input
- Vss sig out
6.5L
6.5L VIN F, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (bottom front of engine, near crank pulley) crankshaft position (ckp) sensor
- (engine harn, 31 cm from taillamp harn breakout)
- (i/p harn, approx 16 cm into i/p cluster breakout)
- (top center of engine) boost pressure sensor
- (top of engine, near
- (top rear of right cylinder head) g117
- (top right front of engine, near thermostat housing) engine coolant temperature (ect) sensor
- 4wd signal
- 5 volt ref
- 5 vref
- 5v ref volt
- A 1-2 red shift sol
- A 2-3 red shift sol
- A torque red converter clutch pulse wdth mod sol
- A/c request sig
- A/c system
- A/t fluid pressure (tfp) manual valve position switch
- A/t w/ 4wd
- A10
- A11 3 mode cruise a12
- Anti-lock brakes system
- App 1 sig
- App 2 sig
- App 3 sig
- Automatic transmission
- Automatic transmission input shaft speed (a/t iss) sensor (left side of transmission)
- B10
- B11
- B12
- Brake sw in
- Brake switch input
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- Cam posit sens sig rtn
- Camshaft posit sens
- Closure gnd
- Cruise control system
- Cruise ctrl sw engage
- Cruise eng sw retard
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Ect temp sens in
- Engine crank sens input
- Force mtr hi
- Force mtr low
- Fuel pump input
- Fuel pump rly ctrl
- Fuel sol closure (5v sig)
- Fuel temp sens (5v sig)
- Glow plug "wait" lp out
- Glow plug relay
- Ground
- Ign
- Inline gender adapter
- Intake air temperature (iat) sensor
- Intake man air temp sens
- Intake manifold
- Map sens input
- Nca
- Opening)
- Others
- Pnk
- Powertrain control module (pcm) (behind right side of dash, near blower motor)
- Pressure control solenoid valve
- Radio, evo/ passlock control module, transfer case control module
- Range mode sel a
- Range mode sel b
- Range mode sel c
- Red
- S140
- S170
- S199
- S211
- S215
- Sensor gnd
- Tan
- Timing stepper mtr (high)
- Timing stepper mtr (low)
- Transmission speed input
- Transmission temp input
- Transmission temperature sensor
- Transmissions system
- Vehicle speed input
- Vehicle speed sensor (left side of transmission)
- Vehicle speed sensor buffer (behind right side of dash)
- Vss hi
- Vss lo
- Vss output
- Vss rtn
- Vss sig
6.5L VIN F, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (a/t: eng harn, approx 4 cm from i/p harness breakout, m/t: i/p harn, 20 cm from inflatable restraint i/p module switch breakout)
- (on inj pump)
- 5 volt ref
- Accelerator pedal position (app) module (part of accelerator pedal)
- Clutch pedal position (cpp) switch (m/t only) (top of clutch pedal bracket)
- Cmp sig
- D2 trans fuse 20 20a e1
- D8 stop/haz fuse 1 20a c7
- Ecm-1 h7
- Electronic brake control module (on left side of engine compt)
- Engine shutoff solenoid (top of fuel injection pump)
- Fuel solenoid (rear of fuel injection pump)
- Fuel solenoid driver (left side of fuel injection pump)
- Fuse 20a
- High res sig
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block
- Injection timing stepper motor (top right front of engine)
- M4 brake fuse 18 10a n3
- Nca
- Optical fuel temperature sensor (on top of fuel injection pump)
- Pnk
- Pnk pnk
- Power distribution system
- Red
- S166
- S190
- S198
- S220 (i/p harness, approx 6 cm from steering column breakout)
- S222 (m/t) s152 (a/t)
- S299
- Sens grd
- Stop- lamp switch (on top of brake pedal)
- Tan d
- Underhood fuse/relay center
6.5L VIN F, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (inside left frame rail, below driver's door)
- (m/t: engine harness, approx 37 cm from breakout to ebcm, a/t: engine harness, approx 31 cm from taillamp harn breakout) s100
- (taillamp ext harn, 10 cm from fuel pump balance mod breakout)
- (top rear of right cylinder head)
- (top rear of right cylinder head) g117
- Auxiliary tank fuel level sensor
- Ecm-b fuse 20a
- F11
- Fuel balance pump
- Fuel gauge
- Fuel lift pump
- Fuel pump balance module (inside left side frame rail)
- Fuel pump balance relay (on fuel pump balance module)
- Fuel pump prime connector (left side of eng compt)
- Fuel pump relay (in under fuse- relay center)
- Fuel pump/oil pressure switch
- G117
- G12
- G415 (inside left frame rail, near rear crossmember)
- Gauges fuse 4 10a
- Hot at all times
- Hot in run or start
- I/p fuse block
- Ign--e fuse 10a
- Instrument cluster
- Instrument cluster system
- Nca
- Pnk
- Primary tank fuel level sensor
- Red
- S101
- S103
- S147
- S213
- S315
- S317
- S318
- S319
- Service engine soon indicator
- Service throttle soon indicator
- Tan
- Underhood fuse/relay center
- Vehicle speed input
- W/ dual tanks
- W/o dual tank
- Wait to start "glow plugs" indicator
- Water in fuel indicator
- Water in-fuel sensor (on fuel filter/ manager)
6.5L VIN F, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500:
- "serv eng soon" ind
- "serv throttle soon" ind
- (engine harness, approx 13 cm into ebcm breakout)
- (on fuel manager/filter) fuel heater
- 12v battery (fused)
- 12v battery fused
- 3/2 ctrl out
- A/c enable
- A/c system
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Data link connector (dlc) (under left side of dash, left of steering column)
- Eng-i k7
- Engine shutoff sol out
- Fuel sol module (5 vref)
- Fuel sol module feed
- Fuse 20a
- Fusible link
- G117 (top rear of right cylinder head)
- Glow plug 1
- Glow plug 2
- Glow plug 3
- Glow plug 4
- Glow plug 5
- Glow plug 6
- Glow plug 7
- Glow plug 8
- Glow plug output
- Glow plug relay (top left rear of engine)
- Grd
- Hot at all times
- Hot in run or start
- Ign
- Ignition
- Nca
- Pcm gnd
- Pnk
- Powertrain control module (pcm) (behind right side of dash, near blower motor)
- Red
- Relay ctrl
- S103
- S108
- S137
- S138
- S147
- S150
- S191
- S269
- Serial data sig
- Shift sol a input
- Shift sol b input
- Tan
- Tps 2 ref voltage
- Underhood fuse/relay center
- Wait to start ind
- Wastegate sol
- Wastegate solenoid (top left rear of engine)
7.4L
7.4L VIN J, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Engine Performance Wiring Diagrams (1 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (19 cm into oxygen sensor harn)
- (attached to right rear of throttle body) idle air control (iac) valve
- (bottom front of engine near, crank pulley) crankshaft position sensor
- (top right side of engine) evaporative emission canister purge solenoid valve
- 1-2 shift sol ctrl
- 2-3 shift sol ctrl
- A/t w/ 4wd
- Air pump rel ctrl
- Cam posit sens sig
- Camshaft position sensor (inside distributor)
- Crank posit sens sig
- Ect sens sig
- Egr posit sig
- Fuel gauge lvl
- Fuel level input
- Fuel tank press sens
- G119 (right front side of eng block)
- Heated oxygen sensor (bank 1 sensor 1) (in left exhaust pipe in front of catalytic converter)
- Heated oxygen sensor (bank 2 sensor 1) (in right exhaust pipe in front of catalytic converter)
- Heated oxygen sensor (bank 2 sensor 2) (in right exhaust pipe in back of catalytic converter) (california)
- Ho2s low
- Ho2s sig
- Iat sens sig
- Idle air ctrl (iac) a hi
- Idle air ctrl (iac) b lo
- Ign feed
- Inj 1 ctrl
- Inj 2 ctrl
- Inj 3 ctrl
- Inj 4 ctrl
- Inj 5 ctrl
- Inj 6 ctrl
- Inj 7 ctrl
- Inj 8 ctrl
- Inline gender adapter
- Knock sens sig
- Knock sensor (ks) (left) (left side of engine block, below exhaust manifold)
- Knock sensor (ks) (right) (right side of engine block, below exhaust manifold)
- Map sens input
- Mass air flow sens sig
- Nca
- Others
- Pnk
- Pnk c ignition feed
- Pnk pnk
- Pnk pnk pnk pnk
- S114
- S148
- S149
- S162
- Sens rtn
- Sens sig
- Sensor return
- Tan
- Tcc pwm sol ctrl
- Temp sens input
- Throttle posit sens
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (left side of transmission, left side of transfer case w/ 4wd)
- Vent ctlr
- Vss rtn
- Vss sig
- Vss signal
- W/ dual fuel tanks
7.4L VIN J, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Engine Performance Wiring Diagrams (2 of 4) for Chevrolet Cab & Chassis C2000 2500:
- 2-3 shift red
- Air injection reaction pump clutch (on front of air pump)
- Air injection reaction relay (underhood fuse/ relay center)
- Automatic transmission
- Automatic transmission fluid pressure (tfp) manual valve position switch
- Ecm1 fuse 20a
- Eng1 k7
- Evaporative emissions (evap) purge solenoid vacuum switch (on top of engine) (california)
- Exhaust gas recirculation (egr) valve (on top left side of eng)
- Fluid temperature sensor
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuse 20a l8
- G119 (right front side of eng block)
- Heated oxygen sensor (bank 1 sensor 2) (in left exhaust pipe in back of catalytic converter) (california)
- Hot in run & start
- Nca
- Pnk
- Pnk pnk pnk pnk
- Pnk pnk pnk tan red
- Pressure control solenoid valve
- Red
- S104
- S108
- S147
- S154
- S155
- Solenoid
- Tan
- Torque convertor clutch pulse width modulation solenoid
- Underhood fuse/relay center
7.4L VIN J, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Engine Performance Wiring Diagrams (3 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (eng harn,
- (eng harn, approx 4 cm from egr valve breakout)
- (engine harn)
- (inside left frame rail, near rear crossmember)
- (inside left frame rail, near rear crossmember) g415
- (taillamp extension harness, approx 10 cm from fuel pump balance module breakout)
- 7 cm from egr valve breakout) s106
- Automatic transmission input shaft speed sensor (left side of transmission)
- Aux tank fuel lvl sig
- Auxiliary fuel tank level sensor (in fuel tank)
- Balance fuel pump (on inside left frame rail, near front of rear tank)
- Convenience center (under left side of dash)
- D w/ dual fuel tanks
- Engine coolant temperature sensor (top right front of engine, near thermostat housing)
- F7 ign e fuse 10a g8
- Fuel gauge input
- Fuel pump & sender (w/o dual fuel tanks) (in fuel tank)
- Fuel pump balance module (inside left side of frame rail)
- Fuel pump balance relay (on fuel pump balance module)
- Fuel pump module (w/ dual fuel tanks)
- Fuel tank pressure sensor (in fuel tank) (california)
- Fuel tanks
- G117 (back side of eng block, below right side of cylinder head)
- G415
- Gauges fuse 4 10a
- Ground
- Hot in off, run or start
- Hot in run or start
- I/p fuse block
- Ignition
- Instrument cluster
- Intake air temperature sensor (in air intake duct)
- Manifold absolute pressure (map) sensor (top right front of engine)
- Mass air- flow sensor (in air intake duct)
- Output to gauge c2
- Pnk
- Pnk a
- Pnk pnk tan red
- Primary tank fuel lvl sig
- Relay ctrl
- S103
- S146
- S213
- S231
- S232
- S315
- S318
- S319
- S324
- S430
- Service engine soon indicator
- Speedometer input
- Tachometer input
- Tan a
- Throttle position sensor (on throttle body assembly)
- Trans fuse 20 10a
- Underhood fuse/relay center
- W/ dual fuel tank
- W/ dual w/o dual fuel tank
- W/o dual fuel tank
- W/o dual fuel tanks
7.4L VIN J, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Engine Performance Wiring Diagrams (4 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (back side of eng block, below right side of cylinder head)
- (engine harness, approx 13 cm from s150
- (engine harness, approx 7 cm from ebcm breakout)
- (i/p harn, 13 cm from ccm)
- (i/p harn, 20 cm from inflatable restraint switch breakout)
- (i/p harness, approx 40 cm from instrument cluster breakout)
- (or
- 4wd input
- 5v ref voltage
- 87a
- A/c comp enable rel
- A/c request signal
- A/t
- Air conditioning system
- Air inlet vlv mtr ctlr
- Automatic 4wd
- Automatic transfer case controller
- Aux fan relay
- Brake sw input
- Brake switch input
- Check eng lp ctrl
- Clutch pedal position (cpp) switch (at top of clutch pedal bracket)
- Cooling fans system
- Cpp sw input
- Cruise control module (left rear of engine compt, on firewall)
- Cruise ctrl sig eng
- Data link connector (under left side of dash, left side of steering column)
- Distributor
- Dual fuel mod return
- Ebcm breakout)
- Egr vlv feed
- Egr vlv ground
- Electronic brake control module (ebcm) (on left side of engine compt)
- Electronic variable orifice/ passlock control module (center of dash)
- Est output sig
- Evap can purge vlv
- F11 ecmb fuse 20a
- Force motor feed
- Force motor return
- Four whl dr sig
- Four whl dr sig lo
- Fuel level input
- Fuel pump a prime connector (left rear of eng compt)
- Fuel pump relay
- Fuel pump rly ctrl
- G117
- G12
- Ground
- High voltage coil wire
- Hot at all times
- Hot in run
- I/p fuse block
- Ign coil out
- Ign input
- Ign timing sig.
- Ignition
- Ignition coil
- Ignition control module (on rear of intake manifold)
- Ignition feed
- M/t
- M4 brake fuse 18 10a n3
- Manual or selectable 4wd
- Pnk
- Pnk a
- Pressure switch input
- Radio
- Red
- S101
- S103
- S111 (engine harness, approx 7 cm from ebcm breakout)
- S151
- S152
- S153
- S221
- Sensor ground
- Sensor return
- Serial data sig
- Speed sensor
- Speed sensor input
- Stoplamp switch (top of brake pedal)
- Stoplamp/ clutch switch input
- Switch signal
- Trans input speed rtn
- Trans input speed sig
- Transfer case control module (under dash, on steering column support bracket)
- Transfer case switch (left top of transfer case)
- Transmissions system
- Underhood fuse/ relay center
- Vcm sig
- Vehicle control module (vcm) (left side of engine compt)
- Vss input
- Vss sig out
EXTERIOR LIGHTS
Back-up Lamps Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Back-up Lamps Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (chassis cab) a c
- (ex chassis cab)
- (left side of transmission) back-up lamp switch
- A c
- A/t
- G415 (left frame rail, behind bumper)
- Hot in run or start
- I/p fuse block
- Left back-up lamp
- M/t
- Mirrors system (automatic day/night mirror)
- Pnk
- Right back-up lamp
- S411
- S414
- Trailer tow connector
- Transmission range switch (left side of transmission)
- Turn b/u fuse 16 20a
Exterior Lamps Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Exterior Lamps Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (dash harness behind left side of dash) s210
- (execpt suburban/ utility)
- (forward lamps harn, 35 cm from wiper harn breakout) s122
- (forward lamps harness, 5 cm from right headlamp breakout) s127
- (front to rear body harness, near chmsl harness breakout)
- (license lamp harness, near license lamp toward taillamp breakout) s415
- (rear lamps harn, 27 cm from trailer harness breakout) (w/ duel rear wheels) s413
- (tail- lamp harness, near taillamps extension harness break- out) s412
- Aux fuse 22 20a
- Auxiliary lead (taped to harness)
- Back-up lights circuit
- Cargo lamp
- Cargo lamp (2 bulbs)
- Cargo lamp switch
- Center high mount stop lamp
- Chmsl lamp (2 bulbs)
- Cruise control system
- Ctsy fuse 20a
- Fuse block
- G108 (left radiator support, near left headlamp)
- G119 (right front of engine block)
- G1o1 (right front side of engine compt)
- G201 (right side of dash)
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- G415 (left frame rail, behind bumper)
- H9 turn pwr h8 haz pwr h7 flshr out g8 gnd
- Hazard
- Headlamp & panel dimmer switch
- Headlights system
- Hot at all times
- Hot in run, bulb test or start
- I/p fuse block
- Instru- ment cluster
- Interior lights system
- Left
- Left front marker lamp
- Left front park/ turn lamps
- Left spotlamp assembly (police package)
- Left tail/ stop/ turn lamp
- Left turn indic
- License lamp
- License lamps
- Maxi fuse 30a
- Nca
- Normal
- Off
- Park
- Park lps fuse 9 20a
- Pickup
- Pnk
- Police package (1999 only)
- Rear clearance lamps circuit
- Red
- Rheo- stat
- Right
- Right front marker lamp
- Right front park/ turn lamps
- Right spotlamp assembly (police package)
- Right tail/ stop/ turn lamp
- Right turn indic
- Roof marker lamps
- S107
- S119 (forward lamps harn, 16 cm from wiper harn breakout)
- S123
- S128
- S204
- S215
- S220 (dash harn, 6 cm from column harness breakout)
- S242
- S259
- S283 (spotlamp ext harness)
- S299
- S316
- S411
- S416
- S419
- S421 (tail/stop lamp harness, 7 cm from g415)
- S422 (tail/stop lamp harn, 7 cm from trailer harness breakout)
- S424
- Stop- lamp relay (except subur- ban/ utility)
- Stop/ haz fuse 1 20a
- Stoplamp switch (top of brake pedal)
- Suburban/ utility
- Trailer tow connector
- Turn- b/u fuse 16 15a
- Turn/ hazard switch
- Turn/hazard flasher (on convenience center)
- Under- hood fuse relay center (left rear of engine compt)
- Under- hood fuse- relay center (left rear of engine compt)
- W/ dual rear wheels
- W/ step bumper
- W/o step bumper
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram (1 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for Ground Distribution Wiring Diagram (1 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (i/p harness, approx 24 cm from instrument cluster breakout)
- (left front of intake manifold)
- A16
- Ashtray lamp
- Audio alarm module
- Automatic transfer case control module
- Automatic transfer case select switch
- Auxiliary cooling fan motor
- Auxiliary heater control switch (utility)
- Body control module
- Brake trans- mission shift interlock switch
- C10
- Cargo lamp switch (pickup)
- Cigar lighter
- Convenience center
- D10
- D12
- D13
- Data link connector
- Daytime running lamps module
- Fog lamp switch (luxury)
- Front auxiliary power outlet
- Front windshield wiper/ washer pump motor
- G101 (right front side of eng compt, at wheelhousing)
- G101 (right front wheelhouse)
- G105 (right rear of engine compt)
- G108 (left radiator support, near left headlamp)
- G110 (diesel)
- G117 (right rear of engine)
- G121 (top center of firewall)
- G202 (behind left side of dash)
- Ground strap
- Headlamp & panel dimmer switch
- Heater & a/c control switch
- Horn switch
- Hvac control module
- I/p compartment lamp
- Ignition switch
- Inflatable restraint i/p module enable switch
- Key-in warning buzzer switch (luxury)
- Left battery
- Left fog lamp
- Left front door jamb switch
- Left front park/ turn lamp
- Left high beam headlamp
- Left high/ low beam headlamp
- Left horn
- Left low beam headlamp
- Liftgate release switch (utility)
- Low coolant level indicator module (diesel)
- Luxury
- Pickup only
- Radio
- Rear stereo controller
- Rear window washer pump motor
- Rear window wiper/ washer switch (utility)
- Right fog lamp
- Right front door jamb switch
- Right front park/ turn lamp
- Right high beam headlamp
- Right high/ low beam headlamp
- Right horn
- Right low beam headlamp
- S123 (forward lamps harness, approx 23 cm from left park/lamp breakout)
- S128 (forward lamps harness, approx 5 cm from right headlamp breakout)
- S158 (in washer pump jumper harness)
- S204 (i/p harness, approx 10 cm from steering column harn)
- S218 (i/p harness, aprrox 16 cm from dlc breakout)
- S298
- S336 (floor console harn, approx 5 cm from crossbody in-line connector breakout)
- Shock sensor
- Spare
- To s316 (diagram 2 of 4)
- Transfer case control module
- Transfer case select switch
- Turn/ hazard flasher
- Uncoated
- Under- hood lamp
- Vehicle interface unit (luxury)
- W/ dual horns
- W/ quad headlamps
- W/ quad headlamps/ sport package
- Windshield wiper motor module
Ground Distribution Wiring Diagram (2 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for Ground Distribution Wiring Diagram (2 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (4wd harn, approx 10 cm from transfer case relay breakout)
- (eng harn, approx 16 cm into vehicle speed sensor breakout)
- (engine harness, near diode)
- (i/p harness, approx 8 cm from i/p cluster breakout)
- (illuminated vanity mirror jumper, approx 11 cm toward left illuminated vanity mirror)
- (oxygen sensor jumper harn, approx 7 cm from right bank oxygen sensor harn)
- (right front of engine block) g119
- (right front of engine, near thermostat housing)
- 87a
- A.i.r. solenoid check valve
- A/c com- pressor low cutout switch
- A/c compressor clutch
- A/c compressor clutch relay
- A/c compressor cycling switch
- A/c compressor pressure switch
- Air injection reactor pump (7.4l only)
- Air pump motor
- Brake pressure warning switch
- Cruise control module
- Data link connector
- Diesel
- E16
- Electrochromic rearview mirror w/ compass
- Electronic brake control module
- Evo passlock module
- Except utility
- From s204 (diagram 1 of 4)
- Front axle actuator
- Fuel heater
- Fuel pump relay
- G110 (left front of engine)
- G119
- G134 (right top center of cylinder head)
- G202 (left side of dash)
- Gasoline
- Glow plug relay
- Heated oxygen sensor (5.0l: bank 1 sensor 2, 5.7l w/ below 8600 gvw: bank 2 sensor 2, 5.7l w/ over 8600b gvw & 7.4l: bank 1 sensor 2)
- Heated oxygen sensor (5.0l: bank 1 sensor 3, 5.7l w/ below 8600 gvw: bank 1 sensor 2, 5.7l w/ over 8600b gvw & 7.4l: bank 2 sensor 2)
- Heated oxygen sensor bank 1 sensor 1
- Heated oxygen sensor bank 1 sensor 2
- Ignition control module
- Inflatable restraint front end sensor
- Inflatable restraint sensing & diagnostic module
- Instrument cluster
- Left illuminated vanity mirror
- Low coolant level sensor
- Mass airflow sensor
- Park/ neutral position switch
- Right illuminated vanity mirror
- Roof marker lamps
- S103 (eng harn, 5.0l/5.7l: 8 cm from egr, 6.5l/7.4l: 12 cm from starter solenoid breakout)
- S107 (engine harness, 5.0l/5.7l: approx 20 cm egr, 6.5l: approx 40 cm from ebcm, 7.4l: approx 18 cm from ebcm breakout)
- S147 (diesel: eng harn, approx 4 cm from starter motor solenoid, gas: eng harn, approx 5 cm from egr valve breakout)
- S149
- S156
- S162 (5.0l/5.77l: eng harn, 17 cm from starter solenoid breakout, 7.4l: eng harn, approx 15 cm from right bank oxygen sensor breakout)
- S167 (battery harn, at left side of eng compt)
- S185
- S186
- S215
- S302
- S302 (4wd harn, approx 10 cm from transfer case relay breakout)
- S316
- Starter relay
- Stoplamp relay
- Trans range switch
- Transfer case relay
- Transfer case shift control module
- Transfer case shift switch
- Underhood fuse block
- Vehicle control module
- Vehicle speed sensor
- Water in fuel filter
- Water valve (utility)
Ground Distribution Wiring Diagram (3 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for Ground Distribution Wiring Diagram (3 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (i/p harness, approx 12 cm from i/p cluster breakout)
- (left seat harn, approx 5 cm from power seat lumbar switch breakout)
- (right front seat harn, approx 5 cm from power seat lumbar switch breakout)
- (right side of dash)
- Audio amplifier
- Auxiliary power connector rear console
- Base pickup
- Bench seat
- Body control module
- Cargo lamp
- Center high mount stop- lamp
- Data link connector
- Diesel
- Door lock inversion module
- Door lock relay
- E16
- Evo passlock module
- Except pickup & ext. cab
- Four-wheel drive indicator lamp
- Front blower motor
- Fuel gauge sender
- Fuel pump balance module
- Fuel pump relay
- G134 (front top of engine)
- G201
- G905 (right "c" pillar)
- Headlamp control module (luxury)
- Heated mirror relay
- High blower motor relay
- Instrument cluster
- Interior lamp control module
- Left front door lock switch
- Left front power door lock switch
- Left front seat belt switch
- Left power lumbar support motor
- Left power seat adjuster switch
- Left rear heated seat element
- Left rear heated seat module
- Left rear heated seat switch
- Left rear power window switch
- Left rear seat belt switch
- Luxury
- Mass airflow sensor
- Mode door motor
- Others
- Pickup & ext. cab
- Pickup only
- Pickup/ extended & crew only
- Power amplifier relay
- Power door locks only
- Power outside rearview mirror switch
- Power window master switch
- Powertrain control module
- Rear window defogger grid (crew cab)
- Rear window lockout switch (except 2-dr utility)
- Recirculation door motor
- Remote control door lock receiver
- Right front power lumbar support motor
- Right front power outside rear view mirror motor
- Right front power seat adjuster switch
- Right front power seat lumbar motor
- Right front power window switch
- Right front seat belt switch
- Right rear heated seat element
- Right rear heated seat module
- Right rear heated seat switch
- Right rear power window switch
- Right rear seat belt switch
- Right seat power lumbar motor
- S103 (engine harness, approx 12 cm from starter solenoid breakout)
- S215
- S227
- S228
- S244 (hvac harn, approx 8cm from recirculation door breakout)
- S251 (crossbody harness, approx 13cm right of left door harness breakout)
- S259 (crossbody harness, approx 7 cm into seat belt switch breakout)
- S317 (taillamp extension harness, approx 10 cm from fuel gage sender breakout)
- S330 (floor console harn, approx 13 cm from heated seat breakout)
- S337 (left rear heated seat harn)
- S358
- S500
- S500 (inside left front door harness, 8 cm from tweeter speaker breakout)
- Secondary fuel gage sender
- Security led
- Temperature door motor
- Transfer case mode selector illumination lamp
- Transfer case shift control module
- Under- hood fuse block
- Vehicle speed sensor buffer
- W/ a/c
- W/ dual tanks
- W/ rke
- W/o a/c
- W/o rke
Ground Distribution Wiring Diagram (4 of 4) for Chevrolet Cab & Chassis C2000 2500
List of elements for Ground Distribution Wiring Diagram (4 of 4) for Chevrolet Cab & Chassis C2000 2500:
- (auxiliary hvac harn, approx 7 cm from blower motor resistor breakout)
- (diesel)
- (front- to-rear body harn, appr0x 8 cm from chmsl breakout)
- (gas)
- (license lamps harness, approx 8 cm from tail- lamp harness breakout)
- (rear lamps harness, 17-33 cm from taillamps extension breakout)
- (right front seat harn, approx 5 cm from power seat lumbar switch breakout) s321
- Auxiliary blower motor
- Auxiliary heater- a/c logic module
- Auxiliary mode door motor
- Auxiliary temp door motor
- Cargo door lock relay
- Cargo doors
- Center high mount stoplamp
- Chassis cab & heavy duty
- Door lock control module (w/ cargo doors)
- Endgate marker lamps
- Except chassis cab & heavy duty
- Front auxiliary heater-a/c control module
- Front dome lamp
- Fuel pump & sender (primary)
- Fuel pump & sender (secondary)
- G305 (right 'b' pillar)
- G415 (left frame rail, behind bumper)
- G416 (inside left framerail, near rear crossmember)
- Garage door opener
- In-line resistor
- Left cargo door defogger grid
- Left door contact button
- Left front clearance lamp
- Left license lamp
- Left rear clearance lamp
- Left rear tail, stop, license, turn & back-up lamps
- Left rear tail, stop, turn & backup lamps
- Left tail, stop, turn & backup lamps
- Lift gate
- Liftgate release relay
- Liftgate window defogger grid
- Luxury
- Nca
- Pickup w/ dual rear wheels
- Reading lamp overhead console
- Rear auxiliary heater-a/c control module
- Rear auxiliary power connector
- Rear dome lamp
- Rear door jamb switch
- Rear wiper motor module
- Right cargo door defogger grid
- Right door contact button
- Right front clearance lamp
- Right license lamp
- Right rear clearance lamp
- Right rear tail, stop, license, turn & back-up lamps
- Right rear tail, stop, turn & back-up lamps
- Right tail, stop, turn & backup lamps
- S307 (rear hvac control harness, approx 10 cm from hvac logic module breakout)
- S319 (taillamp extension harn, approx 7cm from fuel pump and sender breakout)
- S403
- S410 (front to rear lamps harness, 1213 cm from right rear door speaker breakout)
- S411
- S411 (rear lamps harness, 17-33 cm from taillamps extension breakout)
- S416
- S419
- S424
- Trailer ground (taped back)
- Utility
- W/ dual tanks
HEADLIGHTS
Headlight Wiring Diagram, with Quad Headlamps for Chevrolet Cab & Chassis C2000 2500
List of elements for Headlight Wiring Diagram, with Quad Headlamps for Chevrolet Cab & Chassis C2000 2500:
- (except gas: i/p harn, near strng col harn breakout) (gas: i/p harn, near auxiliary power outlet)
- (forward lamps harn, approx 12 cm from left headlamp breakout toward windshield washer pump)
- Acc
- Brake ind ctrl
- Brake warn in
- Bulb test
- Convenience center (under left side of dash)
- Daytime running lamp module (behind left side of dash)
- Daytime running lamps relay
- Diode 203
- Drl indicator
- Drl relay ctrl
- Drl-fog fuse 15 20a
- Exterior lights system
- Fog lamp relay
- Fog lamp switch
- G101 (right front side of engine compartment)
- G108 (left radiator support)
- G134 (right top center of cylinder head)
- G202 (behind left side of dash)
- Gauges fuse 4 10a
- Ground
- Head
- Head- lamp dimmer switch
- Headlamp & panel dimmer switch
- High beam indicator
- Hot at all times
- Hot in run, bulb test or start
- I/p fuse block (left side of dash)
- Ignition
- Ignition switch
- Illum lamp
- Ind bulb chk
- Instrument cluster
- Instrument cluster system (brake warning indicator)
- Interior lights system
- Lamp feed
- Left fog lamp
- Left high beam head- lamp
- Left low beam head- lamp
- Lighting fuse 8 50a
- Lock
- Nca
- Off
- On indicator
- Park
- Park brake sig
- Park brake warning switch
- Pk lps fuse 9 20a
- Pnk
- Red
- Red c
- Right fog lamp
- Right high beam head- lamp
- Right low beam head- lamp
- Run
- S120 (forward lamps harn, near windshield washer pump breakout, toward left hdlp)
- S121
- S123
- S126
- S128
- S204
- S205
- S210
- S213
- S215
- S218
- S225 (i/p harn, approx 12 cm from radio harn breakout)
- S298
- Start
- Tan
- Underhood fuse block (left rear of engine compt)
- W/ fog lamps
Headlight Wiring Diagram, with Sealed Beam Headlamps for Chevrolet Cab & Chassis C2000 2500
List of elements for Headlight Wiring Diagram, with Sealed Beam Headlamps for Chevrolet Cab & Chassis C2000 2500:
- (except gas: i/p harn, near strng col harn breakout) (gas: i/p harn, near auxiliary power outlet)
- (forward lamps harn, approx 12 cm from left headlamp breakout toward windshield washer pump)
- (high)
- (low)
- A (high)
- A (low)
- Acc
- Brake ind ctrl
- Brake warn in
- Bulb test
- Convenience center (under left side of dash)
- Daytime running lamp module (behind left side of dash)
- Daytime running lamps relay
- Diode 203
- Drl indicator
- Drl relay ctrl
- Drl-fog fuse 15 20a
- Exterior lights system
- Fog lamp relay
- Fog lamp switch
- G101 (right front side of engine compartment)
- G108 (left radiator support)
- G134 (right top center of cylinder head)
- G202 (behind left side of dash)
- Gauges fuse 4 10a
- Ground
- Head
- Head- lamp dimmer switch
- Headlamp & panel dimmer switch
- High beam indicator
- Hot at all times
- Hot in run, bulb test or start
- I/p fuse block (left side of dash)
- Ignition
- Ignition switch
- Illum lamp
- Ind bulb chk
- Instrument cluster
- Instrument cluster system (brake warning indicator)
- Interior lights system
- Lamp feed
- Left fog lamp
- Left head- lamp
- Lighting fuse 8 50a
- Lock
- Nca
- Off
- On indicator
- Park
- Park brake sig
- Park brake warning switch
- Pk lps fuse 9 20a
- Pnk
- Red
- Red c
- Right fog lamp
- Right head- lamp
- Run
- S120 (forward lamps harn, near windshield washer pump breakout toward left headlamp)
- S121
- S123
- S126
- S128
- S204
- S205
- S210
- S213
- S215
- S218
- S225 (i/p harn, approx 12 cm from radio harn breakout)
- S298
- Start
- Tan
- Tan c
- Underhood fuse block (left rear of engine compt)
- W/ fog lamps
HORN
Horn Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Horn Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (inside left door harness, approx 25 cm to outside mirror breakout) s124
- A11
- Base
- Body control module (in center console)
- C1 c9
- C210
- C266
- Convenience center (under left side of dash)
- G101 (right front of engine compt, at wheelhousing)
- G202 (behind left side of dash, below fuse box)
- Horn fuse 20a
- Horn relay
- Horn slip ring
- Horn switch
- Hot at all times
- Left horn (front of vehicle)
- Luxury
- Remote control door lock receiver (behind center of dash)
- Right horn (w/ front end appearance package only) (front of vehicle)
- S113
- S128
- S204
- Steering wheel
- Underhood fuse block
- Underhood fuse block (left rear of engine compt)
- Vehicle interface unit receiver (under- neath right rear seat)
INSTRUMENT CLUSTER
5.7L
5.7L VIN R, Instrument Cluster Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Instrument Cluster Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (6 bulbs)
- (engine harn)
- (taillamp extension harn, approx 10 cm from breakout to ground at left side framerail)
- (taillamp extension harn, approx 6 cm from fuel pump harness breakout)
- 39 (or 1020)
- 5v ref
- 7.4l vin j only
- A/t
- A/t w/4wd
- Accy
- Air bag ind
- Anti- lock brakes ind
- Anti-lock brakes system
- Anti-theft system
- Bat ind
- Brake ind
- Brake pressure warning switch (on underside of electronic brake control module)
- Brake psi
- Check gauges ind
- Check gauges lamp driver
- Convenience center
- Daytime running lamps ind
- Daytime running lamps module (behind left side of dash, taped to panel wiring harness)
- Electronic brake control module (ebcm) (on left side of engine compt)
- Engine controls system (fuel pump balance relay)
- Engine coolant temperature sender (left cylinder head, near 1 spark plug)
- Exterior lights system
- Fuel
- Fuel gauge
- Fuel in
- Fuel pump & sender (in fuel tank)
- Fuel pump balance module (inside left side of frame rail)
- Fuel pump/ oil pressure switch & sender (rear top center of engine)
- Fuel ret
- Fuel tank
- G119 (right front of engine block)
- G134 (right top center of cylinder head)
- Gauges fuse 4 10a
- Headlights system
- Hi beam ind
- Hot in run or start
- Hot in run, bulb test or start
- I/p fuse block
- Ign
- Ign e mini fuse 10a
- Ign sw
- Ignition coil (top left rear of engine)
- Ignition switch
- Illumination
- Instrument cluster
- Interior lights system
- Led dimming
- Left turn ind
- Lock
- M/t
- M/t w/4wd & all w/2wd
- Malfunc- tion indicator lamp (service engine soon)
- Mil ind
- Nca
- Off
- Oil gauge
- Parity prndl
- Park brake switch (on park brake pedal bracket)
- Pk brake
- Pnk
- Prndl
- Prndl a
- Prndl b
- Prndl c
- Right turn ind
- Run
- S103
- S147
- S162
- S213
- S215
- S232
- S315
- S324
- S325 (cali)
- S430
- Safety belt ind
- Secondary fuel gauge sender (in rear fuel tank)
- Security ind
- Sens rtrn
- Single dual fuel tanks
- Speedo
- Speedometer
- Start
- Starting/charging system
- Tach
- Tan
- Temp gauge
- Trans fuse 20 10a
- Transmission range switch (left side of transmission)
- Twisted pair
- Underhood fuse block
- Upshift ind
- Upshift ind (m/t only)
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (left side of transmission, left side of tran- sfer case w/ 4wd)
- Vehicle speed sensor (vss) adapter
- Voltmeter
- Vss
- Warning systems
6.5L
6.5L VIN F, Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Instrument Cluster Wiring Diagram (1 of 2) for Chevrolet Cab & Chassis C2000 2500:
- (6 bulbs)
- 39 (or 1020)
- Air bag ind
- Anti- lock brakes ind
- Anti-lock brakes system
- Anti-theft system
- Bat ind
- Brake ind
- Check gauges ind
- Check gauges lamp driver
- Daytime running lamps ind
- Dimming led
- Engine controls system
- Engine coolant temperature sensor (on top right front of engine, near thermostat housing)
- Exterior lights system
- Fuel gauge
- Fuel pump/ oil pressure switch & sender (under intake manifold, center of engine)
- G119 (right front of engine block)
- G134 (front top of engine)
- G202 (behind left side of dash)
- Generator
- Gnd
- Headlights system
- Hi beam ind
- Ign
- Illumination
- Instrument cluster
- Interior lights system
- Left turn ind
- Low coolant ind
- Low coolant level indicator module (behind center of dash)
- Low coolant level switch (in coolant reservoir, right side of engine compt)
- Oil press
- Pnk
- Prndl
- Prndl a
- Prndl b
- Prndl c
- Prndl parity
- Right turn ind
- S107
- S147
- S215
- S298
- Safety belt ind
- Security ind
- Service engine soon ind
- Service throttle soon ind
- Solid state
- Speed- ometer
- Starting/charging system
- Tach
- Tan
- Temp gauge
- Transmission range switch (left side of transmission)
- Volt- meter
- Wait to start ind
- Warning systems
- Water in fuel ind
- Water-in fuel sensor (on fuel filter/ manager)
6.5L VIN F, Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Instrument Cluster Wiring Diagram (2 of 2) for Chevrolet Cab & Chassis C2000 2500:
- (i/p harn, 16 cm into cluster breakout)
- 4wd a/t
- 4wd m/t & all 2wd
- A/t
- Accy
- Anti-lock brakes system
- Brake ind
- Brake pressure warning switch (on rear of ebcm casting)
- Brake psi
- Daytime running lamps module (behind left side of dash, taped to panel wiring harness)
- Dual fuel tanks
- Electronic brake control module (ebcm) (on left side of engine compt)
- Eng 1 mini fuse 20a
- Engine controls system
- Engine controls system (fuel pump balance relay)
- Fuel gauge sender (in front fuel tank)
- Fuel pump & sender
- Fuel pump balance module (inside left side of frame rail)
- Fuse/relay block (left rear of engine compt)
- G119 (right front of engine block)
- G134 (front top of engine)
- Gauges fuse 4 10a
- Hot in run or start
- Hot in run, bulb test or start
- I/p fuse block (under left side of dash)
- Ign e mini fuse 10a
- Ign sw
- Ignition switch
- Lock
- M/t
- Nca
- Off
- Park brake switch (on park brake pedal bracket)
- Pk brake
- Pnk
- Radio
- Run
- S103
- S107
- S108
- S211
- S213
- S215
- S315
- S317
- Secondary fuel gauge sender (in rear fuel tank)
- Single fuel tank
- Start
- Trans fuse 20 10a
- Twisted pair
- Vehicle speed sensor (left side of transmission, left side of transfer case w/ 4wd)
- Vehicle speed sensor (vss) adapter
- Vehicle speed sensor buffer (behind right side of dash)
7.4L
7.4L VIN J, Instrument Cluster Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Instrument Cluster Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (6 bulbs)
- (engine harn)
- (taillamp extension harn, approx 10 cm from breakout to ground at left side framerail)
- (taillamp extension harn, approx 6 cm from fuel pump harness breakout)
- 39 (or 1020)
- 5v ref
- 7.4l vin j only
- A/t
- A/t w/4wd
- Accy
- Air bag ind
- Anti- lock brakes ind
- Anti-lock brakes system
- Anti-theft system
- Bat ind
- Brake ind
- Brake pressure warning switch (on underside of electronic brake control module)
- Brake psi
- Check gauges ind
- Check gauges lamp driver
- Convenience center
- Daytime running lamps ind
- Daytime running lamps module (behind left side of dash, taped to panel wiring harness)
- Electronic brake control module (ebcm) (on left side of engine compt)
- Engine controls system (fuel pump balance relay)
- Engine coolant temperature sender (left cylinder head, near 1 spark plug)
- Exterior lights system
- Fuel
- Fuel gauge
- Fuel in
- Fuel pump & sender (in fuel tank)
- Fuel pump balance module (inside left side of frame rail)
- Fuel pump/ oil pressure switch & sender (rear top center of engine)
- Fuel ret
- Fuel tank
- G119 (right front of engine block)
- G134 (right top center of cylinder head)
- Gauges fuse 4 10a
- Headlights system
- Hi beam ind
- Hot in run or start
- Hot in run, bulb test or start
- I/p fuse block
- Ign
- Ign e mini fuse 10a
- Ign sw
- Ignition coil (top left rear of engine)
- Ignition switch
- Illumination
- Instrument cluster
- Interior lights system
- Led dimming
- Left turn ind
- Lock
- M/t
- M/t w/4wd & all w/2wd
- Malfunc- tion indicator lamp (service engine soon)
- Mil ind
- Nca
- Off
- Oil gauge
- Parity prndl
- Park brake switch (on park brake pedal bracket)
- Pk brake
- Pnk
- Prndl
- Prndl a
- Prndl b
- Prndl c
- Right turn ind
- Run
- S103
- S147
- S162
- S213
- S215
- S232
- S315
- S324
- S325 (cali)
- S430
- Safety belt ind
- Secondary fuel gauge sender (in rear fuel tank)
- Security ind
- Sens rtrn
- Single dual fuel tanks
- Speedo
- Speedometer
- Start
- Starting/charging system
- Tach
- Tan
- Temp gauge
- Trans fuse 20 10a
- Transmission range switch (left side of transmission)
- Twisted pair
- Underhood fuse block
- Upshift ind
- Upshift ind (m/t only)
- Vehicle control module (vcm) (left side of engine compt)
- Vehicle speed sensor (left side of transmission, left side of tran- sfer case w/ 4wd)
- Vehicle speed sensor (vss) adapter
- Voltmeter
- Vss
- Warning systems
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram, Old Style for Chevrolet Cab & Chassis C2000 2500
List of elements for Courtesy Lamps Wiring Diagram, Old Style for Chevrolet Cab & Chassis C2000 2500:
- (crossbody harn, approx 22 cm from left door harn breakout)
- (i/p harn, approx 6 cm from i/p compt box lamp breakout) s208
- (w/ rke)
- Bat
- Braided ground strap
- Cargo door jamb switch (suburban/ utility only)
- Courtesy lamps
- Ctrl
- Ctsy fuse 3 20a
- Dome defeat
- Dome lamp defeat
- Door jamb
- Door lock control module (in front of left rear wheelwell)
- Front dome/ reading lamps
- G201 (right side of dash)
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- Gages fuse 4 10a
- Gnd
- Headlamp & panel dimmer switch
- Horn fuse 20a
- Hot at all times
- Hot in run, bulb test or start
- I/p compart- ment box lamp
- I/p fuse block
- Ign sw
- Interior lamp control module (under center of dash)
- Lamp out
- Left
- Left front door courtesy lamp (if equipped)
- Left front door jamb switch
- Left i/p courtesy lamp
- Left illuminated vanity mirror
- Left rear door courtesy lamp (if equipped)
- Mirrors system
- Nca
- Overhead console lamps circuit
- Pnk
- Pnk a
- Pnk j
- Rear dome/ reading lamps (if equipped)
- Rear door jamb switch (if equipped)
- Remote control door lock receiver (behind center of dash)
- Right
- Right front door courtesy lamp (if equipped)
- Right front door jamb switch
- Right i/p courtesy lamp
- Right illuminated vanity mirror
- Right rear door courtesy lamp (if equipped)
- S113
- S204
- S209 (i/p harn, approx 13 cm from i/p compt box lamp breakout)
- S213
- S218
- S242
- S246
- S248
- S251
- S262 (crossbody harn, approx 19-25 cm from seat belt switch breakout)
- S312
- S316
- S410
- S417 (4 door) (2 door) (front to rear (front to body harn, rear body approx 20 cm harn, approx into crossbody 34 cm from front harn dome lamp breakout) breakout)
- S426
- Underhood fuse/relay center
- Underhood lamp
- W/ overhead console
- W/ rke
- W/o overhead console
- W/o rke
Instrument Illumination Wiring Diagram, Old Style (1 of 2) for Chevrolet Cab & Chassis C2000 2500
List of elements for Instrument Illumination Wiring Diagram, Old Style (1 of 2) for Chevrolet Cab & Chassis C2000 2500:
- (behind left side of dash)
- (crossbody harn, approx 6 cm in left door harn breakout)
- (floor console harn, 12 cm from cd player harn breakout) s333
- (right side of dash)
- Ash tray lamp
- Body control module (in center console)
- Exterior lights system
- G201
- G202
- G305 (right "b" pillar)
- Garage door opener lamp
- Headlamp & panel dimmer switch
- Hot at all times
- I/p fuse block
- Left front power window switch
- Left rear heated seat switch
- Left rear power window switch
- Off
- Parade mode sw
- Park
- Park lps fuse 9 20a
- Power outside rearview mirror switch
- Rear stereo controller
- Rear window lockout switch
- Rheo- stat
- Right front power window switch
- Right rear heated seat switch
- Right rear power window switch
- S210 (i/p harn, approx 12 cm from steering column harn breakout)
- S218
- S247
- S251
- S259
- S321
- S330
- S336
- S500
- S502 (left front door harn, near tweeter)
Instrument Illumination Wiring Diagram, Old Style (2 of 2) for Chevrolet Cab & Chassis C2000 2500
List of elements for Instrument Illumination Wiring Diagram, Old Style (2 of 2) for Chevrolet Cab & Chassis C2000 2500:
- (6) bulbs
- (behind left side of dash)
- (front to rear body harn, 5 cm from auxiliary hvac fan switch breakout)
- (i/p harn, near i/p cluster breakout) s217
- Audio alarm module (on convenience center)
- Automatic transfer case control switch (luxury) c1
- Automatic transfer cash select switch
- Auxiliary heater control switch (subur- ban/ utilitiy only)
- Base
- Cargo lamp switch (pickup only)
- Conven- ience center
- Daytime running lamp (drl)/ radio override switch
- Daytime running lamps (drl)/ radio override switch
- Display dim sig
- Fog lamp switch
- Front auxiliary hvac control lamp
- G131 (near thermostat housing)
- G201 (right side of dash)
- G202
- G305 (at right "b" pillar)
- Headlamp & panel dimmer switch
- Hot at all times
- Hvac control lamp
- I/p fuse block
- Illum fuse 14 10a
- Illumination
- Inflatable restaint i/p module switch
- Instrument cluster
- Liftgate release switch (subur- ban/ utilitiy only)
- Luxury
- Off
- Parade mode sw
- Park
- Park lps fuse 9 20a
- Pickup/ extended cab only
- Radio
- Rear auxiliary hvac control lamp
- Rear auxiliary hvac control switch
- Rear window wiper/ washer switch (subur- ban/ utilitiy only)
- Rheo- stat
- S204
- S215
- S216 (i/p harn, near i/p cluster breakout)
- S218
- S253 (cross- body harn, near i/p harn breakout)
- S259
- S307
- S310
- Suburban & utility only
- Transfer case shift illumination lamp
- Transfer case switch
- Z56 only
Overhead Console Lamps Wiring Diagram, Old Style Base for Chevrolet Cab & Chassis C2000 2500
List of elements for Overhead Console Lamps Wiring Diagram, Old Style Base for Chevrolet Cab & Chassis C2000 2500:
- (front to rear body harn, approx 34 cm from front dome lamp breakout) (2 door) s417
- (under center of dash) (w/o rke) interior lamp control module
- Courtesy lamps
- Courtesy lamps circuit
- Ctsy fuse 3 20a
- Front dome/ reading lamps
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- Headlamp & panel dimmer switch
- Hot at all times
- I/p fuse block
- Int lamp output
- Int lamp output c1
- Overhead console reading lamps
- Rear dome/ reading lamps
- Remote control door lock receiver (w/rke) (behind center of dash)
- S204
- S209 (i/p harn, approx 13 cm from i/p compt lamp breakout)
- S246 (crossbody harn, approx 22 cm from left door harn breakout)
- S320
- S321
- S410
- S426
POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 5) for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Distribution Wiring Diagram (1 of 5) for Chevrolet Cab & Chassis C2000 2500:
- (crossbody harn, approx 22 cm from left door harness breakout)
- (diesel-eng harn, 6.5cm from ebcm breakout gasoline-eng harn, 12cm from ebcm breakout)
- (eng harn, approx 19cm from electronic brake control module breakout) s113
- (i/p harn, near steering column harness breakout) s205
- (overhead console harn, between garage door opener & reading lamp)
- (stud a)
- (stud b)
- (vanity mirror jumper harn, approx 4 cm from inside rearview mirror)
- 175a
- 7.4l
- A nca
- A/c comp fuse 10a
- A/c compressor clutch relay
- Abs fuse 4 60a
- Aux fan fuse 30a
- Aux pwr auto headlap fuse 22 20a
- Auxiliary cooling fan relay
- Blower fuse 3 50a
- Body control module (bcm)
- Brake lamp relay
- C13
- Camp/trail fuse 30a
- Cargo lamp switch
- Convenience center
- Ctsy fuse 3 20a
- D13
- Daytime running lamps relay
- Diode
- Drl/fog fuse 15 20a
- Dual battery
- Ecm-b fuse 20a
- Electronic brake control module
- Evo/ passlock module
- Front dome lamp
- Front dome lamps
- Fuel pump oil pressure switch
- Fuel pump relay
- Fusible link (5 ga-rust)
- Garage door opener
- Generator (base)
- Generator (uplevel)
- Headlamp & panel dimmer switch
- Headlamp and panel dimmer switch
- Headlamp control module
- Heater mirror relay
- High blower motor relay
- Horn fuse 20a
- Horn relay
- Htd mir fuse 10a
- Hvac control module
- I/p compartment box lamp
- I/p fuse block
- Interior lamp control module
- Left battery (diesel)
- Left courtesy lamp
- Left front door courtesy lamp
- Left rear door courtesy lamp
- Left vanity mirror
- Lighting fuse 8 50a
- Luxury only
- Mega fuse block
- Overhead console reading lamps
- Pickup only
- Pk lps fuse 9 20a
- Power outside rearview mirror switch
- Powertrain control module (diesel)
- Rear dome lamps
- Red
- Remote battery stud
- Right battery
- Right courtesy lamp
- Right front door courtesy lamp
- Right rear door courtesy lamp
- Right vanity mirror
- Rr defog fuse 30a
- S101
- S242 (i/p harn, 12cm from inflatable restraint switch breakout)
- S248 (crossbody harn, approx 35 cm from left front door harn breakout)
- S312 s312
- S325
- S426
- S443
- Security/ strg fuse 21 10a
- Seo fuse 30a
- Single battery (base)
- Single battery (uplevel)
- Spare power source
- Starter motor solenoid
- Stop fuse 2 50a
- To fusible link (diagram 5 of 5)
- To underhood fuse block (diagram 2 of 5)
- Underhood fuse block
- Underhood lamp
- Vehicle control module (gasoline)
- W/o rear auxiliary heater or a/c
- W/o rke
Power Distribution Wiring Diagram (2 of 5) for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Distribution Wiring Diagram (2 of 5) for Chevrolet Cab & Chassis C2000 2500:
- (2dr w/ rke & 4dr)
- (crossbody harn, 20 cm from convenience center breakout) s255
- (crossbody harn, approx 19 cm from conenience center)
- (front-to-rear body harn, approx 6 cm from convenience center breakout)
- (i/p harn, 12cm from steering column harness breakout) s200
- (i/p harn, 4cm from auxiliary power outlet breakout)
- (i/p harn, 4cm from steering column harness breakout)
- (i/p harn, approx 10 cm into steering column harn breakout)
- (i/p harn, left rear of engine compartment)
- (luxury only)
- (power lumbar seat jumper harn, approx 13 cm from right power seat breakout)
- (utility only)
- 30a (others)
- 8cm from i/p cluster breakout) s264
- Audio alarm module
- Audio amplifier
- Automatic
- Automatic transfer case
- Automatic transfer case control module
- Aux/pwr fuse 7 25a
- Base
- Base cargo door
- Base cargo doors/upper level liftgate
- Base liftgate/ upper level cargo doors
- Battery fuse 7 50a
- Cargo door lock relay
- Cig ltr fuse 13 20a
- Cigar lighter
- Convenience center
- D14
- D15
- Data link connector
- Door lock control module
- Door lock relay
- Electric
- From underhood fuse block (diagram 1 of 5)
- Front auxiliary power connector
- G202 (left side of dash)
- I/p fuse block
- Left front door lock switch
- Left front power lumbar seat switch
- Left power seat adjuster switch
- Liftgate release relay
- Liftgate release switch
- Luxury level
- Luxury only
- Non- base
- Others
- Pickup
- Pickups w/o rke
- Power amplifier relay (suburban)
- Pwr-accy circuit breaker a (regular 20a cab/extended cab/luxury)
- Radio
- Radio batt fuse 19 10a
- Rear auxiliary power connector (luxury)
- Rear console auxiliary power connector (luxury)
- Rear door lock switch
- Red
- Remote control door lock receiver
- Remote control door lock receiver (uplevel speakers)
- Right front door lock switch
- Right front power lumbar seat switch
- Right front power seat lumbar switch
- Right lumbar power seat switch
- Right power seat adjuster switch
- S212
- S218
- S236
- S237
- S255
- S256
- S272
- S299
- S300
- S434
- Stop lamp switch
- Stop/haz fuse 1 20a
- Suburban/ utility
- T case fuse 2 20a
- To underhood fuse block (diagram 3 of 5)
- Transfer case control module
- Turn/ hazard switch
- Underhood fuse block
- Vehicle interface unit
- W/ rke
- W/bench seat
Power Distribution Wiring Diagram (3 of 5) for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Distribution Wiring Diagram (3 of 5) for Chevrolet Cab & Chassis C2000 2500:
- (a/t)
- (battery harn, red
- (cross body harn, 8cm from convenience center breakout)
- (floor console harn, 33 cm heated seat switch breakout)
- (gas) (diesel)
- (i/p harn, 12cm from steering column harn breakout) pnk
- (i/p harn, 22 cm before radio harn breakout) s292
- (i/p harn, 4 cm from steering column harn breakout) s213
- (i/p harn, 8 cm from automatic transfer case module breakout)
- (i/p harn, approx 8 cm from steering column harn breakout) s201
- (inside left front door harn at breakout to window motor regulator)
- (m/t)
- (w/o rke) (w/ rke)
- A j
- A/t
- Acc
- Air bag fuse 10 10a
- At left side of eng compt) s167
- Audio alarm module
- Automatic transmission controls
- Back-up lamp switch
- Body control module
- C210
- Clutch pedal position switch
- Convenience center
- Crank fuse 8 10a
- Daytime running lamps module
- Daytime running lamps relay
- Electrochromic rearview mirror w/ compass
- Evo/ passlock module
- From ignition switch (diagram 3 of 5)
- From underhood o
- Fuse block (diagram 2 0f 5)
- Gauges fuse 4 10a
- Headlamp control module
- Headlamp/ panel dimmer switch
- I/p fuse block
- Ign a fuse 6 40a 50a
- Ign b fuse 5 50a
- Ignition switch
- Inflatable restraint i/p module switch (pickup)
- Inflatable restraint sensing & diagnostic module
- Instrument cluster
- Interior lamp control module or remote control door lock receiver
- Lock
- Low coolant level indicator module (diesel)
- Luxury
- Luxury only
- M/t
- Off
- Others
- Park/neutral position switch
- Pnk
- Pnk k
- Pnk s207
- Power window master switch
- Pwr wdo circuit breaker 30a
- Radio
- Radio batt fuse 17 10a
- Rear stereo controller
- Rear window lockout switch (4-dr)
- Rear window wiper/washer switch (suburban/utility)
- Red
- Right front power window switch (2 dr & utility)
- Rr wiper fuse 23 25a
- Run
- S266
- S290
- S501
- Start
- Starter relay
- To s206 (diagram 5 of 5)
- To s207 (diagram 3 of 5)
- To underhood fuse block (diagram 4 of 5)
- To underhood fuse block (diagram 5 of 5)
- Trans fuse 20 10a
- Transfer case control module (selectable 4wd electric shift)
- Transfer case select switch
- Turn b/u fuse 16 20a
- Turn signal/ hazard switch
- Underhood fuse block
- Vehicle interface unit
- Vehicle speed sensor buffer (diesel)
- Windshield wiper motor module
- Windshield wiper/ washer switch
- Wiper fuse 11 25a
Power Distribution Wiring Diagram (4 of 5) for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Distribution Wiring Diagram (4 of 5) for Chevrolet Cab & Chassis C2000 2500:
- (eng harn, 12 cm from fuel injector breakout)
- (eng harn, 30cm from ebcm breakout)
- (eng harn, approx 4 cm from i/p harn breakout) s166
- (eng harn, approx 5 cm from back-up lamp switch harn breakout)
- (eng harn, approx 8 cm from egr breakout)
- (eng harn, s146
- (in injector harn jumper)
- (taillamp extension harn, approx 17 cm from fuel pump
- 26 cm from ebcm breakout)
- 5.0l, 5.7l
- 6.5l pnk
- 7.4l
- 7.4l w/ california emissions
- A/c clutch relay
- A/c compressor clutch relay
- Air relay
- Balance module breakout) s315
- C11
- C12
- Crank- shaft position sensor
- Diesel
- Ecm 1 fuse 20a
- Egr linear pwm valve solenoid
- Egr solenoid
- Eng-1 fuse 20a
- Engine shutoff solenoid
- From splice s207 k (diagram 3 of 5)
- Fuel heater
- Fuel injector
- Fuel pump balance module
- Fuel pump balance relay
- Fuel solenoid driver
- Glow plug relay
- Ign e fuse 10a
- Ignition coil
- Ignition control module
- Mass airflow sensor
- Others
- Pnk
- Powertrain control module
- S104
- S108
- S154
- S155
- S161
- S190
- Underhood fuse block
- Vehicle control module
- Waste gate solenoid
- Water-in- fuel sensor
Power Distribution Wiring Diagram (5 of 5) for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Distribution Wiring Diagram (5 of 5) for Chevrolet Cab & Chassis C2000 2500:
- (auxiliary a/c harn, 17cm from blower motor relays)
- (crossbody harn, 20 cm from sdm breakout)
- (crossbody harn, 27 cm from left rear heated seat breakout)
- (crossbody harn, approx 25 cm from sdm breakout)
- (eng harn, 7cm from ebcm) breakout)
- (floor console harn, approx 28 cm from left heated switch breakout) s332
- (hvac harn, approx 4 cm from recirculation door breakout)
- (i/p harn, 6cm from steering column harness breakout)
- (i/p harn, approx 7cm from inflatable restraint switch breakout) s268
- (i/p harn, approx 8 cm from steering column breakout)
- (luxury)
- (others)
- (rear hvac control harn, approx 5 cm from hvac logic module breakout) s308
- (tailamp extension harn, appr0x 10 cm from breakout to ground at left side frame rail, near crossmember)
- 4wd fuse 24 20a
- A13
- Automatic transfer case control module
- Automatic transfer case only
- Automatic transfer case select switch
- Auxiliary battery
- Auxiliary battery relay (left rear of engine compt)
- Auxiliary heater & a/c control logic module
- Auxiliary heater & a/c control module (front)
- Auxiliary heater & a/c control module (rear)
- Auxiliary high blower motor relay
- Auxiliary low blower motor relay
- Auxiliary medium blower motor relay
- Auxiliary mode door motor
- Auxiliary temperature door motor
- Brake fuse 18 10a
- Convenience center
- Cruise control module (gas only)
- Cruise control switch
- Cruise fuse 6 10a
- Diesel
- E10
- Electronic brake control module
- From ignition switch (diagram 3 of 5)
- From underhood e fuse block (diagram 3 of 5)
- From underhood fuse block (diagram 1 of 5)
- Front axle actuator
- Front heated seats fuse 20a
- Fusible link
- G100 (left front fender)
- Gas, base models
- Gas, except base models
- Htr-a/c fuse 12 25a
- Hvac control module
- I/p fuse block
- Left front heated seat module
- Left front heated seat switch
- Left rear heated seat module
- Left rear heated seat switch
- Luxury level
- Luxury models
- Mode door motor
- Rear heated seats fuse 20a
- Rear heater only
- Rear heater w/ cargo doors
- Rear heater w/ lift- gate
- Recirculation door motor
- Red
- Right front heated seat module
- Right front heated seat switch
- Right rear heated seat module
- Right rear heated seat switch
- Rr hvac fuse 5 10a
- S151
- S206
- S233
- S235
- S238
- S243
- S281
- S324
- S326
- S400
- Seats fuse 40a
- Spare power source
- Stop lamp switch
- Suburban utility only
- Temperature door motor
- Transfer case switch (k3500)
- Underhood fuse block
- Vehicle control module (gas only)
- W/ rear defrost
POWER DOOR LOCKS
Door Lock Wiring Diagram, with Crew Cab for Chevrolet Cab & Chassis C2000 2500
List of elements for Door Lock Wiring Diagram, with Crew Cab for Chevrolet Cab & Chassis C2000 2500:
- (crossbody harn, near seat belt switch breakout) s262
- (crossbody harn, under left side of dash) s258
- (crossbody harness, near door lock relay breakout) s256
- (front to rear harness, near dome lamp harn breakout) s434
- (front to rear harness, near rear window harn breakout) s431
- (i/p harn, 6 cm from glove box lamp breakout)
- 2 door 4 door
- 4 door
- Batt (b+)
- C210
- Cig ltr fuse 13 20a
- Convenience center (left side of dash)
- Door jamb sw
- Door lock control module (front of left rear wheelhouse)
- Door lock relay (under center of dash)
- G201 (right side of dash)
- G202 (behind left side of dash)
- G305 (right "b" pillar)
- Ground
- Hot at all times
- I/p fuse block (left side of dash)
- Left front door jamb switch
- Left front door lock actuator
- Left front door lock switch
- Left rear door jamb switch
- Left rear door lock actuator
- Lock
- Lock sig
- Pwr accy circuit breaker 30a
- Rear cargo door lock actuator (cargo doors)
- Rear door jamb switch
- Rear door lock switch (cargo doors)
- Right front door jamb switch
- Right front door lock actuator
- Right front door lock switch
- Right rear cargo door contactor (right rear door jamb)
- Right rear door jamb switch
- Right rear door lock actuator
- Rr door sw
- S204
- S208
- S218
- S255
- S257 (crossbody harness, near door lock relay harness breakout)
- S259
- S260 (crossbody harness, 6 cm from seat belt switch breakout)
- S261 (crossbody harness, 12 cm from seat belt switch breakout)
- S264
- S296
- S410
- S432 (front to rear harness, near left rear speaker harness breakout)
- Tan
- Unlock
- Unlock sig
Door Lock Wiring Diagram, without Crew Cab for Chevrolet Cab & Chassis C2000 2500
List of elements for Door Lock Wiring Diagram, without Crew Cab for Chevrolet Cab & Chassis C2000 2500:
- (inside right door harness) s601
- C210
- Convenience center (under left side of dash)
- G202 (behind left side of dash)
- Hot at all times
- I/p fuse block (under left side of dash)
- Left front door lock motor
- Left front door lock switch
- Lock
- Pwr accy circuit breaker 20a
- Right front door lock motor
- Right front door lock switch
- S255
- S500
- S600 (inside right door harness)
- Solid state
- Tan
- Unlock
Keyless Entry Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Keyless Entry Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (cross body harness, 6cm from seat belt switch breakout)
- (crossbody harn, near seat belt switch breakout) s262
- (crossbody harn, under left side of dash) s258
- (front to rear harness, near rear window harn breakout) s431
- (i/p harn, 6 cm from glove box lamp breakout)
- (regular/extended cab) (except regular/extended cab)
- (utility w/ cargo doors)
- 1576 (or 56)
- 2 door
- 4 door
- 640 (or 540)
- Batt (b+)
- C210
- Cargo door jamb switch
- Cargo door lock switch (w/ cargo doors)
- Cig ltr fuse 13 20a
- Convenience center (left side of dash)
- Data link connector (under left side of dash)
- Dome lamps
- Dome lmp off
- Door jamb sw
- Door lock control module (front of left rear wheelwell)
- Door lock relay (under center of dash, near remote control door lock receiver)
- Driver dr unlk
- G201 (behind right side of dash)
- G201 (right side of dash)
- G305 (right "b" pillar)
- Gauges fuse 4 10a
- Ground
- Horn ctrl
- Horns system
- Hot at all times
- Hot in run, bulb test or start
- I/p fuse block (left side of dash)
- Ignition
- Interior lamps system
- Left front door jamb switch
- Left front door lock actuator
- Left front door lock switch
- Left rear door jamb switch
- Left rear door lock actuator
- Lock
- Lock out
- Lock sig
- Pass drs unlk
- Pnk
- Program sig
- Pwr accy circuit breaker 20a 30a
- Rear cargo door lock actuator (cargo doors)
- Remote control door lock receiver (behind center of dash)
- Right front door jamb switch
- Right front door lock actuator
- Right front door lock switch
- Right rear cargo door contactor (right rear door jamb)
- Right rear door jamb switch
- Right rear door lock actuator
- Rr door sw
- Rr lftgte unlk
- S204
- S208
- S213
- S218
- S251
- S255
- S256
- S257 (crossbody harness, near door lock relay harness breakout)
- S259
- S261 (crossbody harness, 7 cm from seat belt switch harn breakout)
- S264 (suburban/ utility)
- S296 (luxury)
- S410
- S432 (front to rear harness, near left rear speaker harness breakout)
- S434
- Tan
- Trunk, tail- gate, fuel doors system
- Unlock
- Unlock out
- Unlock sig
- Utility w/ rear cargo doors
- Utility w/ rear liftgate
- W/ cargo doors
- W/ liftgate
- W/ power windows
- W/o power windows
POWER MIRRORS
Electrochromic Mirror Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Electrochromic Mirror Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind left side of dash) g202
- (eng harn, near breakout to ebcm)
- (luxury)
- A/t
- Ambient sensor (windshield side)
- Back-up lamp switch (on left side of trans- mission)
- Back-up lamp switch (part of park/neutral position switch) (on left side center of transmission)
- C/m
- C1 f
- Exterior lights system
- Gauges fuse 4 10a
- Ground
- Headlamp sensor (mirror side)
- Headlight control module signal
- Headlights system
- Hot in run or start
- I/p fuse block (under left side of dash)
- Inside automatic day-night mirror
- Left outside automatic day-night mirror (luxury)
- M/t
- Mirror input
- Mirrors switch
- Nca
- Off
- On indicator control
- Pnk
- Power distribution system
- Reset to daytime high reflectivity in reverse
- Right outside automatic day-night mirror (luxury)
- S160
- S213
- S279 (crossbody harness, approx 38 cm from convenience center pnk breakout)
- S316
- Solid state
- Switch breakout) s278
- T/m
- Temperature sensor (behind center grille)
- Turn b/u fuse 16 20a
Power Mirror Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Mirror Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (except upper level)
- (inside left front door harness)
- (inside right front door harness)
- (right side of dash) g201
- (upper level)
- Automatic day-night sensor (upper level)
- C a
- Ctsy fuse 3 20a
- D d
- Defogger system (heated mirror)
- Down
- E c
- Electro- chromic mirror circuit
- F b
- Heating element (upper level)
- Hot at all times
- I/p fuse block
- Interior lights system
- Left
- Left power outside rearview mirror
- Left/ right motor
- Pnk
- Power outside rearview mirror switch
- Right
- Right power outside rearview mirror
- S248
- S251
- S503
- Up/ down motor
POWER SEATS
6-Way Power Seat Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6-Way Power Seat Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (regular/extended cab) (except regular extended cab)
- (right side of dash)
- Back
- Forward/ rearward motor
- Front dn
- Front tilt motor
- Front up
- Fwd
- G201
- Hot at all times
- I/p fuse block
- Left power seat adjuster switch
- Pwr-accy circuit breaker 20a 30a
- Rear dn
- Rear tilt motor
- Rear up
- Right power seat adjuster switch
- S227
- S228
- S255
- Tan
Front Seat Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Front Seat Heater Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (cross body harn, left side of dash, near convenience center)
- (left heated seat harn, near heated seat control module breakout)
- (not used)
- Batt
- C236
- Convenience center
- Front heated seats fuse 20a
- G201 (right side of dash)
- Gnd
- Heated seat sw sig
- High/low sig
- Hot at all time
- Hot in run
- I/p fuse block
- Indicator lmp feed
- Left front heated seat module (under left front power seat)
- Left front heated seat switch
- Left front seat back element
- Left front seat cushion
- Left front seat cushion element
- Left front seat temper- ature sensor
- Off
- Right front heated seat module (under right front power seat)
- Right front heated seat switch
- Right front seat back element
- Right front seat bealt switch
- Right front seat cushion
- Right front seat cushion element
- Right front seat temper- ature sensor
- Rr hvac fuse 5 10a
- S227
- S233
- S238
- S259
- S273
- S274
- S277
- S278
- Sig enable
- Underhood fuse/relay center
Lumbar Wiring Diagram, with Bucket Seat for Chevrolet Cab & Chassis C2000 2500
List of elements for Lumbar Wiring Diagram, with Bucket Seat for Chevrolet Cab & Chassis C2000 2500:
- (w/ regular/extended cab) (except regular extended cab)
- C210 c
- Convenience center
- G201 (right side of dash)
- Hot at all times
- I/p fuse block
- Left front power lumbar seat switch
- Left front power lumbar support motor
- Left lumbar solenoid
- Pwr-accy circuit breaker 20a 30a
- Right front power lumbar seat switch
- Right front power lumbar support motor
- Right lumbar solenoid
- S227
- S228
- S237
- S241
- S259
- Tan
Lumbar Wiring Diagram, without Bucket Seat for Chevrolet Cab & Chassis C2000 2500
List of elements for Lumbar Wiring Diagram, without Bucket Seat for Chevrolet Cab & Chassis C2000 2500:
- C210 b
- Cig ltr fuse 13 20a
- Convenience center
- G201 (right side of dash)
- Hot at all times
- I/p fuse block
- Left front power lumbar seat switch
- Left front power lumbar support motor
- Left lumbar solenoid
- Red
- Right front power lumbar seat switch
- Right front power lumbar support motor
- Right lumbar solenoid
- S227
- S228
- S256
- S259
- S264 (suburban utility only)
- Tan
- W/ split bench seat
- W/o split bench seat
POWER WINDOWS
Power Window Wiring Diagram, 2 Door for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Window Wiring Diagram, 2 Door for Chevrolet Cab & Chassis C2000 2500:
- Auto window down module
- Convenience center (under left side of dash)
- Down
- G201 (right side of dash)
- Hot in run
- I/p fuse block (under left side of dash)
- Interior lights system
- Left front
- Left front window motor
- Left power window master switch
- Pwr wdo circuit breaker 30a
- Right front
- Right front window motor
- Right front window switch
- S251
- S259
- S266
- S500
- S501
- Solid state
- Tan
Power Window Wiring Diagram, 4 Door for Chevrolet Cab & Chassis C2000 2500
List of elements for Power Window Wiring Diagram, 4 Door for Chevrolet Cab & Chassis C2000 2500:
- Convenience center (under left side of dash)
- Down
- G201 (right side of dash)
- Headlamp & panel dimmer switch
- Hot at all times
- Hot in run
- I/p fuse block (under left side of dash)
- Left front
- Left front power window master switch
- Left front window motor
- Left rear
- Left rear window motor
- Left rear window switch
- Pk lps fuse 20a
- Pwr wdo circuit breaker 30a
- Right front
- Right front window motor
- Right front window switch
- Right rear
- Right rear window motor
- Right rear window switch
- S247 (crossbody harn, approx 6 cm into left door harn breakout)
- S251
- S259
- S263
- S500
- S501
- S502 (inside left front door harness, approx 4 cm from tweeter breakout)
- Solid state
- Tan
- Window lockout switch
RADIO
Radio Wiring Diagrams, with Amplifier for Chevrolet Cab & Chassis C2000 2500
List of elements for Radio Wiring Diagrams, with Amplifier for Chevrolet Cab & Chassis C2000 2500:
- (left side of dash) data link connector
- (lf door harn, near window reg breakout)
- (rf door harn, near door lock motor breakout)
- Amp feed
- Antenna
- Audio rtn
- Bare
- Battery
- Cig ltr fuse 13 20a
- Diesel
- Dim
- Dim feed
- Display dim
- Drain rtn
- E&c diag
- Fuse out
- G201 (right side of dash)
- G202 (left side of dash)
- Gas
- Ground
- Hot at all times
- Hot in acc or run
- I/p fuse block
- Interior lights system
- Left front speaker
- Left front tweeter
- Left rear door speaker
- Left rear speaker
- Lf +
- Lf -
- Lr +
- Lr dr +
- Lr dr -
- Lr _
- Lr+
- Lr-
- Lt audio
- Lt remote
- Nca
- Pnk
- Power amplifier (under left side of dash)
- Power amplifier relay (under left side of dash)
- Radio
- Radio batt fuse 19 10a
- Radio fuse 17 10a
- Red
- Remote audio player
- Remote rtn
- Rf +
- Rf -
- Right front speaker
- Right front tweeter
- Right rear door speaker
- Right rear speaker
- Rly sig
- Rr +
- Rr -
- Rr dr +
- Rr dr -
- Rr+
- Rr-
- Rt audio
- Rt remote
- S221
- S249
- S250
- S251
- S252
- S254
- S256
- S259
- S298
- S504
- S505
- S603
- S604
- Serial data
- Tan
- Tape ctrl
- Vehicle control module (left side of engine compartment)
- Vehicle speed sensor buffer (behind right side of dash)
- Vss signal
Radio Wiring Diagrams, without Amplifier for Chevrolet Cab & Chassis C2000 2500
List of elements for Radio Wiring Diagrams, without Amplifier for Chevrolet Cab & Chassis C2000 2500:
- (left side of dash) data link connector
- (lf door harn, near window reg breakout)
- (rf door harn, near door lock motor breakout)
- Amp feed
- Antenna
- Audio rtn
- Bare
- Battery
- Diesel
- Dim
- Dim feed
- Display dim
- Drain rtn
- E&c diag
- Fuse out
- G202 (left side of dash)
- Gas
- Ground
- Hot at all times
- Hot in acc or run
- I/p fuse block
- Interior lights system
- Left front speaker
- Left front tweeter
- Left rear speaker
- Lf +
- Lf -
- Lr +
- Lr _
- Lt audio
- Lt remote
- Nca
- Pnk
- Radio
- Radio batt fuse 19 10a
- Radio fuse 17 10a
- Remote audio player
- Remote rtn
- Rf +
- Rf -
- Right front speaker
- Right front tweeter
- Right rear speaker
- Rr +
- Rr -
- Rt audio
- Rt remote
- S221
- S298
- S504
- S505
- S603
- S604
- Serial data
- Tan
- Tape ctrl
- Vehicle control module (left side of engine compartment)
- Vehicle speed sensor buffer (behind right side of dash)
- Vss signal
SHIFT INTERLOCKS
Shift Interlock Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Shift Interlock Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- Automatic transmission shift lock control (btsi) solenoid (right side of steering column)
- G202 (behind left side of dash)
- Hot in run or start
- I/p fuse block
- Park/ neutral position switch (left side of transmission)
- Pnk
- S204
- Transfer case control module (under dash on steering column support bracket)
- Turn/ hazard switch
- Turn/bu fuse 16 20a
- W/ electric shift transfer case
STARTING/CHARGING
5.7L
5.7L VIN R, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (dash harness, approximately 4 cm (1.5 in) from steering pnk
- (on right front of engine block) g119
- (right front wheelhouse) g101
- 175a
- All others
- Battery
- Charge warning indicator
- Column harness breakout, towards data link connector) s213
- Fusible link
- Gauges fuse 4 20a
- Generator
- Hot in run & start
- I/p fuse block (under left side of dash)
- Instrument cluster
- Mega fuse block (on right front of engine compartment, near battery)
- Pnk
- Power distribution system
- Red
- Uplevel/ enhanced
5.7L VIN R, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (on left rear of engine compartment) fuse/relay block
- 175a
- A/t
- Acc
- Battery
- Bulb test
- Clutch pedal position switch (on top of clutch pedal bracket)
- Crank fuse 8 10a
- G101 (right front wheel house)
- G119 (on right front of engine block)
- I/p fuse block (under left side of dash)
- Ign a fuse 6 40a
- Ignition switch
- Lock
- M/t
- Mega fuse block (on right front of engine compartment, near battery)
- Off
- Park/ neutral position switch (on left side, center of transmission)
- Red
- Remote battery stud
- Run
- S107
- Start
- Starter motor
- Starter relay
- Starter solenoid
6.5L
6.5L VIN F, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (alternator jumper harness, approximately 18 cm (7 in) from right generator)
- 100a b
- 100a/105a b
- 124a l
- 175a
- All others
- Charge warning indicator
- Fusible link
- G101 (right front wheelhouse)
- G110 (left front of intake manifold)
- G117 (right rear of cylinder head)
- Gauges fuse 4 10a
- Generator
- Generator (w/ dual generators)
- Hot in run & start
- I/p fuse block (under left side of dash)
- Instrument cluster
- Left battery
- Mega fuse block (right front of engine compt, near battery)
- Nca
- Pnk
- Power distribution system
- Red
- Right battery
- S213
- Uplevel/ enhanced
6.5L VIN F, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- A/t
- Acc
- Bulb test
- Clutch pedal position switch (on top of clutch pedal bracket)
- Crank fuse 8 10a
- Fuse/relay block (on left rear of engine compartment)
- G101 (right front wheel- house)
- G110 (left front of intake manifold)
- G117 (right rear of cylinder head)
- I/p fuse block (under left side of dash)
- Ign a fuse 6 40a
- Ignition switch
- Left battery
- Lock
- M/t
- Off
- Park/ neutral position switch (on left side, center of transmission)
- Red
- Remote battery stud
- Right battery
- Run
- S107
- Start
- Starter motor
- Starter relay
- Starter solenoid
7.4L
7.4L VIN J, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Charging Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (dash harness, approximately 4 cm (1.5 in) from steering pnk
- (on right front of engine block) g119
- (right front wheelhouse) g101
- 175a
- All others
- Battery
- Charge warning indicator
- Column harness breakout, towards data link connector) s213
- Fusible link
- Gauges fuse 4 20a
- Generator
- Hot in run & start
- I/p fuse block (under left side of dash)
- Instrument cluster
- Mega fuse block (on right front of engine compartment, near battery)
- Pnk
- Power distribution system
- Red
- Uplevel/ enhanced
7.4L VIN J, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, Starting Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (on left rear of engine compartment) fuse/relay block
- 175a
- A/t
- Acc
- Battery
- Bulb test
- Clutch pedal position switch (on top of clutch pedal bracket)
- Crank fuse 8 10a
- G101 (right front wheel house)
- G119 (on right front of engine block)
- I/p fuse block (under left side of dash)
- Ign a fuse 6 40a
- Ignition switch
- Lock
- M/t
- Mega fuse block (on right front of engine compartment, near battery)
- Off
- Park/ neutral position switch (on left side, center of transmission)
- Red
- Remote battery stud
- Run
- S107
- Start
- Starter motor
- Starter relay
- Starter solenoid
SUPPLEMENTAL RESTRAINTS
Supplemental Restraint Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Supplemental Restraint Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (behind left kick panel) g200
- (behind left kick panel) g202
- (behind left side of dash) g202
- (crossbody harness, approximately 7 cm (2.5 inches) into seat belt switch) s259
- (i/p harness, approximately 16 cm (6 inches) from instrument cluster harness, breakout, towards cigar lighter harness breakout) s218
- (i/p harness, approximately 4 cm (1.5 inches) from steering column harness breakout, towards data link connector (dlc)) s213
- (sir harness, 35 cm (13.5 inches) before inflatable restraint sensing & diagnostic module (sdm) s276
- (sir harness, 35 cm (13.5 inches) before mobile communications, system wire breakout, towards inflatable restraint sensing & diagnostic module (sdm))
- Air bag fuse 10 10a
- Air bag indicator
- Air bag indicator ctrl
- Audio alarm module
- Convenience center (under left side of dash)
- Data link connector (dlc) (partial) (under left side of dash, left of steering column)
- Disc sensor input
- Driver seat belt
- Driver side high
- Driver side low
- Gauges fuse 4 10a
- Ground
- Hot in run & start
- I/p fuse block (under left side of dash)
- Ignition
- Inflatable restraint front end discriminating sensor (under front outside center of radiator)
- Inflatable restraint ip module
- Inflatable restraint ip module switch (pick up only)
- Inflatable restraint sensing & diagnostic module (sdm) (under driver's seat carpet)
- Inflatable restraint steering wheel module
- Inflatable restraint steering wheel module coil
- Instrument cluster
- Interior lights system
- Off
- Ohms
- Pass airbag disable
- Pass airbag enable
- Pass side high
- Pass side low
- Pnk
- S282
- Seat belt switch (closed w/seat belt unbuckled) (on driver's seat belt buckle)
- Serial data (uart)
- Shorting bar
- Tan
- W/luxury package
- W/o luxury package
TRANSMISSION
5.7L
5.7L VIN K, A/T Wiring Diagram, 4L60-E for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN K, A/T Wiring Diagram, 4L60-E for Chevrolet Cab & Chassis C2000 2500:
- (dash harn, 20 cm from breakout to inflatable restraint sw)
- (engine harn, 16 cm from egr breakout)
- (engine harn, 6.5 cm from breakout to ebcm)
- (on brake pedal bracket) stoplamp switch
- 1-2 shift sol
- 1-2 shift solenoid
- 2-3 shift sol
- 2-3 shift solenoid
- 2wd
- 3-2 ctrl solenoid
- 3-2 downshift sol
- 4wd
- 4wd circuit (transfer case & axle switches)
- 4wd low signal in
- 5v reference
- Anti-lock brakes system
- Automatic transmission (4l60-e)
- Battery in
- Brake fuse 18 10a
- Brake switch input
- Breakout to egr valve)
- Cruise control
- D3, d2
- D4, d2
- Data class ii
- Data link connector (under left side of dash)
- Ecm 1 fuse 20a
- Ecm b fuse 20a
- Ect sens input
- Electronic brake control module
- Engine controls
- Engine coolant temperature sensor (top right front of engine)
- Fluid temp sensor
- Front wheel lock
- Fuel injectors, ignition control moudule & ignition coil
- Fuel pump & oil press switch/ sender & fuel pump relay
- G120 (right rear of cylinder head)
- Gauges fuse 4 10a
- Hot at all times
- Hot in off, run or start
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition in
- Inline gender adaptor
- Instrument cluster
- Malfunction indicator lamp
- Mil control
- Pcm ground
- Pcs sol hi out
- Pcs sol lo out
- Pnk
- Press ctrl solenoid
- Range signal "a"
- Range signal "b"
- Range signal "c"
- Red
- Rev, lo
- S101
- S103
- S150 (engine harn, 13 cm from breakout to ebcm)
- S151
- S152
- S161
- S213
- S222
- S231
- Sensor ground
- Sensor return
- Tan
- Tcc pwm sol
- Tcc pwm solenoid
- Tcc sol
- Tcc solenoid
- Tcc/abs/ cruise switch
- Throttle position sensor (mounted to side of throttle body)
- Tp sens input
- Trans fuse 20 10a
- Trans range pressure switch assembly
- Trans temp sig in
- Transfer case circuit
- Underhood fuse/relay center (left rear of engine compt)
- Vehicle control module (left side of engine compt)
- Vehicle speed sensor (left side of transmission-2wd) (left side of transfer case-4wd)
- Vss hi (signal)
- Vss lo (ground)
5.7L VIN R, A/T Wiring Diagram, 4L60-E for Chevrolet Cab & Chassis C2000 2500
List of elements for 5.7L VIN R, A/T Wiring Diagram, 4L60-E for Chevrolet Cab & Chassis C2000 2500:
- (dash harn, 20 cm from breakout to inflatable restraint sw)
- (engine harn, 16 cm from egr breakout)
- (engine harn, 6.5 cm from breakout to ebcm)
- (on brake pedal bracket) stoplamp switch
- 1-2 shift sol
- 1-2 shift solenoid
- 2-3 shift sol
- 2-3 shift solenoid
- 2wd
- 3-2 ctrl solenoid
- 3-2 downshift sol
- 4wd
- 4wd circuit (transfer case & axle switches)
- 4wd low signal in
- 5v reference
- Anti-lock brakes system
- Automatic transmission (4l60-e)
- Battery in
- Brake fuse 18 10a
- Brake switch input
- Breakout to egr valve)
- Cruise control
- D3, d2
- D4, d2
- Data class ii
- Data link connector (under left side of dash)
- Ecm 1 fuse 20a
- Ecm b fuse 20a
- Ect sens input
- Electronic brake control module
- Engine controls
- Engine coolant temperature sensor (top right front of engine)
- Fluid temp sensor
- Front wheel lock
- Fuel injectors, ignition control moudule & ignition coil
- Fuel pump & oil press switch/ sender & fuel pump relay
- G120 (right rear of cylinder head)
- Gauges fuse 4 10a
- Hot at all times
- Hot in off, run or start
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition in
- Inline gender adaptor
- Instrument cluster
- Malfunction indicator lamp
- Mil control
- Pcm ground
- Pcs sol hi out
- Pcs sol lo out
- Pnk
- Press ctrl solenoid
- Range signal "a"
- Range signal "b"
- Range signal "c"
- Red
- Rev, lo
- S101
- S103
- S150 (engine harn, 13 cm from breakout to ebcm)
- S151
- S152
- S161
- S213
- S222
- S231
- Sensor ground
- Sensor return
- Tan
- Tcc pwm sol
- Tcc pwm solenoid
- Tcc sol
- Tcc solenoid
- Tcc/abs/ cruise switch
- Throttle position sensor (mounted to side of throttle body)
- Tp sens input
- Trans fuse 20 10a
- Trans range pressure switch assembly
- Trans temp sig in
- Transfer case circuit
- Underhood fuse/relay center (left rear of engine compt)
- Vehicle control module (left side of engine compt)
- Vehicle speed sensor (left side of transmission-2wd) (left side of transfer case-4wd)
- Vss hi (signal)
- Vss lo (ground)
6.5L
6.5L VIN F, A/T Wiring Diagram, 4L80-E for Chevrolet Cab & Chassis C2000 2500
List of elements for 6.5L VIN F, A/T Wiring Diagram, 4L80-E for Chevrolet Cab & Chassis C2000 2500:
- (dash harn, 16 cm from cluster breakout)
- (engine harn, 4 cm fromt breakout to cluster)
- (on brake pedal bracket) stoplamp switch
- (top rear of right cyl head)
- 1-2 shift sol
- 1-2 shift solenoid
- 2-3 shift sol
- 2-3 shift solenoid
- 2wd
- 4wd
- 4wd sig
- A/t iss sens hi
- A/t iss sens in
- A/t iss sens lo
- A/t iss sensor
- A12
- Accelerator pedal position module (part of accelerator pedal)
- App 1 5v ref
- App 1 signal in
- App 2 5v ref
- App 2 signal in
- App 3 5v ref
- App 3 signal in
- Automatic transmission (4l80-e)
- Automatic transmission input shaft speed sensor (left front of transmission)
- B10
- B12
- Battery in
- Brake fuse 18 10a
- Brake switch in
- C11
- C12
- C13
- C14
- C15
- Class ii data
- D11
- D12
- D13
- D3, d2
- D4, d2
- Data link connector (under left side of dash)
- Ecm 1 fuse 20a
- Ecm b fuse 20a
- Ect sensor in
- Electronic brake control module
- Engine controls system
- Engine coolant temperature sensor (near thermostat housing)
- Engine shutoff solenoid, fuel solenoid
- Exterior lights
- From breakout to steering column)
- Fuel pump & oil press switch/ sender & fuel pump relay
- G117
- Gauges fuse 4 10a
- Ground
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- Ignition in
- Inline gender adaptor
- Instrument cluster
- Malfunction indicator lamp
- Mil control
- Pcm ground
- Pcs sol hi out
- Pcs sol lo out
- Pnk
- Power
- Powertrain control module (right side of dash near blower motor)
- Press ctrl solenoid
- Red
- Rev, lo
- S101
- S103
- S140
- S150 (engine harn, 13 cm from breakout to ebcm)
- S152
- S166
- S170
- S211
- S213
- S215
- S299
- Sensor ground
- Stop/haz fuse 1 20a
- Stoplamp switch
- Tan
- Tcc pwm sol
- Tcc pwm solenoid
- Tft sensor in
- Trans fluid temp sensor
- Trans fuse 20 20a
- Trans range
- Trans range "a"
- Trans range "b"
- Trans range "c"
- Trans range pressure switch assembly
- Transfer case circuit
- Turn/ hazard switch & chime module
- Underhood fuse/relay center (left rear of engine compt)
- Vehicle speed sensor (left side of transmission-2wd left side of transfer case-4wd)
- Vehicle speed sensor buffer (right side of dash)
- Vss hi (signal)
- Vss in
- Vss lo (ground)
- Vss out
7.4L
7.4L VIN J, A/T Wiring Diagram, 4L80-E for Chevrolet Cab & Chassis C2000 2500
List of elements for 7.4L VIN J, A/T Wiring Diagram, 4L80-E for Chevrolet Cab & Chassis C2000 2500:
- (5.7l) (7.4l)
- (dash harn, 20 cm from breakout to inflatable restraint sw)
- (engine harn, 16 cm from egr breakout)
- (engine harn, 6.5 cm from breakout to ebcm)
- (on brake pedal bracket) stoplamp switch
- 1-2 shift sol
- 1-2 shift solenoid
- 2-3 shift sol
- 2-3 shift solenoid
- 2wd
- 4wd
- 4wd circuit (transfer case & axle switches)
- 4wd low signal in
- 5v reference
- A/t iss hi in
- A/t iss lo in
- Anti-lock brakes system
- Automatic transmission (4l80-e)
- Automatic transmission input shaft speed sensor (if equipped) (on transmission)
- Battery in
- Brake fuse 18 10a
- Brake switch input
- Breakout to egr valve)
- Cruise control
- D3, d2
- D4, d2
- Data class ii
- Data link connector (under left side of dash)
- Ecm 1 fuse 20a
- Ecm b fuse 20a
- Ect sens input
- Electronic brake control module
- Engine controls
- Engine coolant temperature sensor (top right front of engine)
- Fluid temp sensor
- Front wheel lock
- Fuel injectors, ignition control moudule & ignition coil
- Fuel pump & oil press switch/ sender & fuel pump relay
- G120 (top of right cylinder head)
- Gauges fuse 4 10a
- Hot at all times
- Hot in off, run or start
- Hot in run
- Hot in run or start
- I/p fuse block (under left side of dash)
- I/p fuse block (under left side of dsah)
- Ignition in
- Inline gender adaptor
- Instrument cluster
- Malfunction indicator lamp
- Mil control
- Pcm ground
- Pcs sol hi out
- Pcs sol lo out
- Pnk
- Press ctrl solenoid
- Range signal "a"
- Range signal "b"
- Range signal "c"
- Red
- Rev, lo
- S101
- S103
- S150 (engine harn, 13 cm from breakout to ebcm)
- S151
- S152
- S161 s104
- S213
- S222
- S231
- Sensor ground
- Sensor return
- Tan
- Tcc pwm sol
- Tcc pwm solenoid
- Tcc/abs/ cruise switch
- Throttle position sensor (mounted to side of throttle body)
- Tp sens input
- Trans fuse 20 10a
- Trans range pressure switch assembly
- Trans temp sig in
- Transfer case circuit
- Underhood fuse/relay center (left rear of engine compt)
- Vehicle control module (left side of engine compt)
- Vehicle speed sensor (left side of transmission-2wd) (left side of transfer case-4wd)
- Vss hi (signal)
- Vss lo (ground)
WARNING SYSTEMS
Warning System Wiring Diagrams, Base for Chevrolet Cab & Chassis C2000 2500
List of elements for Warning System Wiring Diagrams, Base for Chevrolet Cab & Chassis C2000 2500:
- (behind left side of dash)
- (near thermostat housing)
- (opens with belt buckled)
- Audio alarm module (on convenience center)
- Diesel
- Fasten belts out
- G119
- G134 (front top of engine)
- G134 (right top center of cylinder head)
- G201 (right side of dash)
- G202
- Gas
- Gauges fuse 4 10a
- Ground
- Hot at all times
- Hot in park or headlight
- Hot in run, bulb test, or start
- I/p fuse block (under left side of dash)
- Ignition on input
- Illum fuse 14 10a
- Instru- ment cluster
- Key-in warning
- Key-in warning buzzer switch (left side of steering column)
- Left front door jamb switch
- Lights on input
- Pnk
- Power input
- S103
- S204
- S213
- S215
- S217
- S259
- S298
- S299
- Safety belts indicator
- Seat belt input
- Seat belt switch (on driver's seat belt buckle)
- Stop/haz fuse 1 20a
- Tan
Warning System Wiring Diagrams, Luxury & Performance for Chevrolet Cab & Chassis C2000 2500
List of elements for Warning System Wiring Diagrams, Luxury & Performance for Chevrolet Cab & Chassis C2000 2500:
- (behind left side of dash)
- (near thermostat housing)
- (opens with belt buckled)
- B tan
- Battery input
- Body control module (in center console)
- C13
- C14
- Ctsy fuse 3 20a
- D11
- D15
- Distribution
- Drvr dr ajar sw
- Fasten belts out
- G119
- G134 (right top center of cylinder head)
- G201 (right side of dash)
- G202
- Gauges fuse 4 10a
- Ground
- Headlamp & panel dimmer switch
- Hot at all times
- Hot in run, or start
- I/p fuse block (under left side of dash)
- Instru- ment cluster
- Key-in warning
- Key-in warning buzzer switch (left side of steering column)
- Left door jamb switch
- Park lamp input
- Pklps fuse 9 20a
- Pnk
- Power
- S103
- S204
- S210 (near convenience center)
- S213
- S215
- S259
- S335
- S336
- Safety belts indicator
- Seat belt input
- Seat belt switch (on driver's seat belt buckle)
- Switched ignition
- System
- Tan
WIPER/WASHER
Wiper/Washer Wiring Diagram for Chevrolet Cab & Chassis C2000 2500
List of elements for Wiper/Washer Wiring Diagram for Chevrolet Cab & Chassis C2000 2500:
- (left radiator support, near left headlamp) g108
- Delay
- Front windshield washer pump (in washer fluid reservoir)
- Front wiper motor module (on center of firewall)
- G202 (behind left side of dash)
- High
- Hot in accy & run
- I/p fuse block (under left side of dash)
- Inst wipe
- Low
- Mist
- Nca
- Off
- Red
- Red a
- S204
- Solid state
- Wash
- Windshield wiper/ washer switch
- Wiper control
- Wiper fuse 25a