COOLING FAN
Auxiliary Cooling Fan Wiring Diagram for Chevrolet Hi-Cube G30 1993
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for Auxiliary Cooling Fan Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- 1995 vftc c
- Auxiliary coolant fan
- Auxiliary cooling fan relay (behind right 'b' pillar)
- Auxiliary cooling fan switch (right center of engine on cylinder head)
- Fuse block (left side of i/p)
- Fusible link (14ga-rust)
- G109 (on right radiator support)
- Gauge fuse 20a
- Hot at all times
- Hot in run or start
- Red
DEFOGGERS
Defogger Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Defogger Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- (g series)
- (r/v series)
- Defogger switch
- Fuse block (left side of i/p)
- Gages fuse ign fuse 20a
- Hot at all times
- Hot in run or start
- I/p bus bar ground
- Illum.
- Interior lights system
- Left rear defogger
- Off
- On ind
- Pwr acc circuit breaker 30a
- Rear defogger
- Right rear defogger
- Timer
- Timer relay
- W/ panel doors
- W/ tailgate
HORN
Horn Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Horn Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- Fuse block (left side of i/p)
- Horn
- Horn relay (left side of i/p))
- Horn switch
- Horn-dm fuse 20a
- Hot at all times
- Interior lights
- Steering column switches
- Z82 only
POWER ANTENNA
Power Antenna Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Power Antenna Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- (behind left side of i/p, near steering column)
- 10a
- Antenna
- Bus bar ground
- C1/a
- C1/b
- C1/c
- C2/a
- C2/b
- C2/c
- Coaxial cable
- Down
- Fuse block
- Horn- dm fuse 20a
- Hot at all times
- In-line fuse
- Pnk
- Power antenna
- Power antenna relay
- Radio
- Red
POWER DOOR LOCKS
Door Lock Wiring Diagram, with Sliding Side Door for Chevrolet Hi-Cube G30 1993
List of elements for Door Lock Wiring Diagram, with Sliding Side Door for Chevrolet Hi-Cube G30 1993:
- (closed w/ door open)
- Bus bar ground (left side of i/p)
- Door lock delay module (behind right side of i/p, on top of cowl panel)
- Door lock delay relay (behind right side of i/p, on top of cowl panel)
- Door lock relay (behind right side of i/p, on top of cowl panel)
- Fuse block (left side of i/p)
- G202
- Ground
- Hot at all times
- Left door lock switch
- Left front door lock motor
- Lock
- Lock enable input
- Lock power input
- Lock relay
- Power
- Power window
- Pwr acc circuit breaker 30a
- Rear door lock motor
- Right door lock switch
- Right front door lock motor
- Side door contact buttons
- Side door lock motor
- Sliding door jamb switch
- Tan
- Unlock
- Unlock power input
- Unlock relay
- W/ power window
- W/o power window
- W/o w/ power window
Door Lock Wiring Diagram, with Swing Out Side Door for Chevrolet Hi-Cube G30 1993
List of elements for Door Lock Wiring Diagram, with Swing Out Side Door for Chevrolet Hi-Cube G30 1993:
- Bus bar ground
- Door lock relay (behind left side of i/p)
- Fuse block (left side of i/p)
- G202 (left side of i/p)
- Hot at all times
- Left door lock motor
- Left door lock switch
- Lock
- Lock relay
- Pwr acc circuit breaker 30a
- Rear door lock motor
- Right door lock motor
- Right door lock switch
- Side door lock motor
- Tan
- Unlock
- Unlock relay
Keyless Entry Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Keyless Entry Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- Alternator
- Battery
- Bus bar ground
- Data link connector (below steering column)
- Diesel
- Door lock relay
- Door lock relay (behind right side of i/p)
- Door lock sw
- Door sw
- Exterior lights system (turn signal sw)
- Fuse block (left side of i/p)
- G202 (left side of i/p, near fuse block)
- Gasoline
- Ground
- Headlight delay sw
- Headlight delay switch
- Headlights system (beam select sw)
- Headlights system (light sw)
- Hot at all times
- Ignition
- Interior lights system
- Keyless entry delay set switch
- Keyless entry module (behind right side of i/p)
- Left door jamb sw
- Left door jamb switch
- Left door lock mtr
- Left door lock switch
- Left front door lock motor
- Light on input
- Lock
- Low beam headlight
- Program enable
- Pwr acc circuit breaker 30a
- Rear door lock motor
- Rear door lock mtr
- Right door jamb switch
- Right door lock switch
- Right door sw
- Right front door lock motor
- Side door contactor
- Side door lock motor
- Tan
- Unlock
POWER MIRRORS
Power Mirror Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Power Mirror Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- Bus bar ground g202 (behind left side of i/p)
- Down
- Fuse block
- Horn/dm fuse 20a
- Hot at all times
- In-line fuse
- Left
- Left outside power mirror
- Left/ right motor
- Power mirror control switch
- Right
- Right outside power mirror
- Up/ down motor
POWER WINDOWS
Power Window Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Power Window Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- 1995 vftc c
- Fuse block (left side of dash)
- G200 (left side of cowl, behind i/p)
- Hot in run
- Left window motor
- Left window switch
- Pnk
- Power window circuit breaker 30a
- Right window motor
- Right window switch
- Tan
RADIO
2-Speaker System Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for 2-Speaker System Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- Antenna
- Antenna input
- Bat+
- Bus bar ground
- C10
- C243
- C245
- Coaxial cable
- Fuse block (under left side of dash)
- Ground
- Horn/dm fuse 20a
- Hot at all times
- Hot in accy or run
- Hot in park or head
- Inst lps
- Inst lps fuse 5a
- Interior lights system
- Left front speaker
- Lights switch
- Lt frt spkr
- Power
- Radio
- Radio fuse 10a
- Right front speaker
- Rt frt spkr
- Tan
Radio Wiring Diagrams, with CD Player or Cassette for Chevrolet Hi-Cube G30 1993
List of elements for Radio Wiring Diagrams, with CD Player or Cassette for Chevrolet Hi-Cube G30 1993:
- Antenna
- Antenna input
- Bat+
- Bus bar ground
- C10
- C17
- C18
- C19
- C20
- C243
- C244
- C245
- Coaxial cable
- Fuse block (under left side of dash)
- Horn-dm fuse 20a
- Hot at all times
- Hot in accy or run
- Hot in park or head
- Inst lps
- Inst lps fuse 5a
- Interior lights system
- Left front speaker
- Left rear speaker
- Light sw
- Lt frt spkr
- Lt rear spkr
- Pnk
- Power
- Power antenna system
- Pwr antenna
- Radio
- Radio fuse 10a
- Right front speaker
- Right rear speaker
- Rt frt spkr
- Rt rear spkr
- Tan
STARTING/CHARGING
Charging Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Charging Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- Battery junction block (left side of cowl, near bulkhead connector)
- Forward battery
- Fuse block (left side of dash)
- Fusible link (rust 12 ga)
- G108 (left radiator support)
- G112 (lower left side of engine, near power steering pump)
- Gages fuse 20a
- Generator
- Hot in run or start
- Rear battery (diesel)
- Red
Starting Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Starting Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- 1995 vftc c
- Acc
- Crank fuse
- Forward battery
- Fusible link (rust 10 ga) (1991 a/t 4spd w/ overdrive)
- Fusible link (rust 20 ga)
- G108 (left radiator support)
- G112 (lower left side of engine, near power steering pump)
- Glow plugs controller (diesel)
- Hot at all times
- Ignition switch
- Lock
- Off
- Power distribution system
- Rear battery (diesel)
- Run
- Start
- Starter motor
TRANSMISSION
4.3L
4.3L (VIN Z), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993
List of elements for 4.3L (VIN Z), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993:
- (left i/p, near convenience center)
- (top rear of park brake bracket)
- (under drivers' seat)
- 1-2 shift sol
- 1-2 shift sol cntrl
- 12 volt batt in
- 12 volt ignition in
- 2-3 cntrl sol cntrl
- 2-3 shift sol
- 2-3 shift sol cntrl
- 3-2 control solenoid
- 5 volt sensor ref
- A12
- A14
- A15
- All times
- B10
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- Cruise control in
- Cruise control module
- Data link connector (partial)
- Dlc
- E10
- E13
- E15
- E16
- Electronic 4-speed automatic overdrive transmission
- F10
- F12
- F14
- Fuse ecm ign 10a
- Fuse ecmb 10a
- Fuse trans 10a
- G117 (rear of engine, near distributor)
- G125 (front of engine, near thermostat)
- Ground
- Hot at
- Hot in run,
- I/p fuse block
- Module (pcm)
- Or start
- Oxygen sens ground
- Pcm ground
- Pcm trans range a
- Pcm trans range b
- Pcm trans range c
- Pnk
- Powertrain control
- Press cntrl sol hi
- Press cntrl sol lo
- Pressure control sol
- Range mode selector
- Red
- Sensor ground
- Serial data
- Stop lamp switch in
- Tan
- Tcc cntrl
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (top of engine, on throttle body)
- Tps in
- Trans temp sensor in
- Trans- mission temp
- Vehicle speed sensor (left rear of transmission)
- Vehicle speed sensor buffer (park brake support bracket)
- Vss in
4.3L (VIN Z), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993
List of elements for 4.3L (VIN Z), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993:
- (under drivers' seat)
- (under steering column) data link connector (partial)
- 1-2 shift sol
- 1-2 shift sol ctrl
- 12 volt battery
- 12 volt ignition
- 2-3 shift sol
- 2-3 shift sol ctrl
- 5 volt sens ref
- A12
- B10
- B11
- Brake signal
- C11
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- D15
- D16
- Dlc
- Electronic 4-speed automatic overdrive transmission
- Fuse ecm batt 10a
- Fuse ecm ign 10a
- Fuse trans 10a
- G115 (rear of engine near distributor)
- G125 (front of engine near thermostat)
- Hot at all times
- Hot in run
- I/p fuse block
- Input speed hi
- Input speed lo
- Module (pcm)
- Or start
- Output speed sensor (left rear of transmission)
- Pnk
- Powertrain control
- Press ctrl sol hi
- Press ctrl sol lo
- Press sw a
- Press sw b
- Press sw c
- Pressure control solenoid
- Pressure switch manifold
- Red
- Sens grd
- Serial data
- System ground
- Tcc driver
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (right side of throttle body)
- Tp sens in
- Trans input speed sensor (left front of transmission)
- Trans- mission temp sensor
- Transmission temp in
- Vehicle speed sensor buffer (park brake support bracket)
- Vss input
5.0L
5.0L (VIN H), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993
List of elements for 5.0L (VIN H), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993:
- (left i/p, near convenience center)
- (top rear of park brake bracket)
- (under drivers' seat)
- 1-2 shift sol
- 1-2 shift sol cntrl
- 12 volt batt in
- 12 volt ignition in
- 2-3 cntrl sol cntrl
- 2-3 shift sol
- 2-3 shift sol cntrl
- 3-2 control solenoid
- 5 volt sensor ref
- A12
- A14
- A15
- All times
- B10
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- Cruise control in
- Cruise control module
- Data link connector (partial)
- Dlc
- E10
- E13
- E15
- E16
- Electronic 4-speed automatic overdrive transmission
- F10
- F12
- F14
- Fuse ecm ign 10a
- Fuse ecmb 10a
- Fuse trans 10a
- G117 (rear of engine, near distributor)
- G125 (front of engine, near thermostat)
- Ground
- Hot at
- Hot in run,
- I/p fuse block
- Module (pcm)
- Or start
- Oxygen sens ground
- Pcm ground
- Pcm trans range a
- Pcm trans range b
- Pcm trans range c
- Pnk
- Powertrain control
- Press cntrl sol hi
- Press cntrl sol lo
- Pressure control sol
- Range mode selector
- Red
- Sensor ground
- Serial data
- Stop lamp switch in
- Tan
- Tcc cntrl
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (top of engine, on throttle body)
- Tps in
- Trans temp sensor in
- Trans- mission temp
- Vehicle speed sensor (left rear of transmission)
- Vehicle speed sensor buffer (park brake support bracket)
- Vss in
5.7L
5.7L (VIN K), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993
List of elements for 5.7L (VIN K), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993:
- (left i/p, near convenience center)
- (top rear of park brake bracket)
- (under drivers' seat)
- 1-2 shift sol
- 1-2 shift sol cntrl
- 12 volt batt in
- 12 volt ignition in
- 2-3 cntrl sol cntrl
- 2-3 shift sol
- 2-3 shift sol cntrl
- 3-2 control solenoid
- 5 volt sensor ref
- A12
- A14
- A15
- All times
- B10
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- Cruise control in
- Cruise control module
- Data link connector (partial)
- Dlc
- E10
- E13
- E15
- E16
- Electronic 4-speed automatic overdrive transmission
- F10
- F12
- F14
- Fuse ecm ign 10a
- Fuse ecmb 10a
- Fuse trans 10a
- G117 (rear of engine, near distributor)
- G125 (front of engine, near thermostat)
- Ground
- Hot at
- Hot in run,
- I/p fuse block
- Module (pcm)
- Or start
- Oxygen sens ground
- Pcm ground
- Pcm trans range a
- Pcm trans range b
- Pcm trans range c
- Pnk
- Powertrain control
- Press cntrl sol hi
- Press cntrl sol lo
- Pressure control sol
- Range mode selector
- Red
- Sensor ground
- Serial data
- Stop lamp switch in
- Tan
- Tcc cntrl
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (top of engine, on throttle body)
- Tps in
- Trans temp sensor in
- Trans- mission temp
- Vehicle speed sensor (left rear of transmission)
- Vehicle speed sensor buffer (park brake support bracket)
- Vss in
5.7L (VIN K), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993
List of elements for 5.7L (VIN K), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993:
- (under drivers' seat)
- (under steering column) data link connector (partial)
- 1-2 shift sol
- 1-2 shift sol ctrl
- 12 volt battery
- 12 volt ignition
- 2-3 shift sol
- 2-3 shift sol ctrl
- 5 volt sens ref
- A12
- B10
- B11
- Brake signal
- C11
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- D15
- D16
- Dlc
- Electronic 4-speed automatic overdrive transmission
- Fuse ecm batt 10a
- Fuse ecm ign 10a
- Fuse trans 10a
- G115 (rear of engine near distributor)
- G125 (front of engine near thermostat)
- Hot at all times
- Hot in run
- I/p fuse block
- Input speed hi
- Input speed lo
- Module (pcm)
- Or start
- Output speed sensor (left rear of transmission)
- Pnk
- Powertrain control
- Press ctrl sol hi
- Press ctrl sol lo
- Press sw a
- Press sw b
- Press sw c
- Pressure control solenoid
- Pressure switch manifold
- Red
- Sens grd
- Serial data
- System ground
- Tcc driver
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (right side of throttle body)
- Tp sens in
- Trans input speed sensor (left front of transmission)
- Trans- mission temp sensor
- Transmission temp in
- Vehicle speed sensor buffer (park brake support bracket)
- Vss input
6.2L
6.2L (VIN C), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993
List of elements for 6.2L (VIN C), Transmission Wiring Diagram, 4L60-E for Chevrolet Hi-Cube G30 1993:
- (left side of engine,
- 2-3 shift sol
- 3-2 shift sol
- 4 wheel drive indicator
- 4wd ind input
- 5v return b
- 5v sensor ref
- 5v system return a
- A14
- A15
- Battery
- Data link connector (under left side of i/p)
- Dlc input
- E10
- E13
- E15
- E16
- Ecm1 fuse 10a
- Ecmb fuse 10a
- Ect sensor
- Electronic 4-speed automatic overdrive transmission
- Engine coolant temp (ect) sensor (top front of engine, on intake manifold)
- Engine speed sensor
- Engine speed sensor (left front of engine)
- F10
- F12
- F13
- F14
- Force motor
- Fuse block: i/p
- G112
- Gages fuse 20a
- Ground
- Hot at all times
- Hot in run or start
- Ign
- Ignition
- Near power steering pump)
- Output speed sensor
- Pcm to brake sw
- Pcm to trans tp sens
- Pnk
- Pnk n
- Powertrain control module (pcm) (under driver's seat)
- Range mode selector
- Red
- Red p
- Serial data
- Shift a sol
- Shift b sol
- Shift solenoid a
- Shift solenoid b
- Speed inputs
- Tan
- Tcc ctrl
- Tcc sol
- Tcc/brake switch (below left side of i/p, above brake pedal)
- Throttle position (tp) sensor (on fuel injection pump)
- Tp sensor
- Trans force motor high
- Trans force motor low
- Trans fuse 10a
- Trans range mode a
- Trans range mode b
- Trans range mode c
- Trans- mission temp
- Vehicle spd output
- Vehicle speed input
- Vehicle speed sensor
- Vehicle speed sensor buffer (on parking brake support bracket)
6.2L (VIN J), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993
List of elements for 6.2L (VIN J), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993:
- 5 volts ref
- A10
- A11
- A12
- Air conditioning
- B10
- B11
- B12
- Battery power
- Brake switch input
- Brake/ transmission shift interlock relay (on steering column)
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- C300
- C301
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Data link connector (partial) (below left side of i/p)
- Dlc input
- Ecm1 fuse 10a
- Ecmb fuse 10a
- Engine speed sensor (top rear of engine)
- Engine speed sensor in
- Force motor hi
- Force motor low
- Fuse block: i/p
- G112 (lower left side of engine, near power steering pump)
- Heavy duty electronic 4-speed automatic overdrive transmission
- Hot at all times
- Hot in run or start
- Ignition
- Instrument cluster circuit
- Pnk
- Pnk d
- Press switch manifold a
- Press switch manifold b
- Press switch manifold c
- Pressure control solenoid
- Pressure switch manifold
- Red
- Red f
- Sensor buffer
- Sensor ground
- Serial data
- Service trans output
- Shift sol a
- Shift sol b
- Shift solenoid a output
- Shift solenoid b output
- Speed sensor input
- System
- System ground
- Tcc sol
- Tcc solenoid
- Tcc/brake switch (below left side of i/p, above brake pedal)
- Throttle postition sensor (on injection pump)
- Tp sensor input
- Trans fuse 10a
- Trans- mission temp sensor
- Transmission control module (tcm) (below driver's seat)
- Transmission input speed sensor (left side of transmission)
- Transmission speed input
- Transmission temp input
- Vehicle speed
7.4L
7.4L (VIN N), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993
List of elements for 7.4L (VIN N), Transmission Wiring Diagram, 4L80-E for Chevrolet Hi-Cube G30 1993:
- (under drivers' seat)
- (under steering column) data link connector (partial)
- 1-2 shift sol
- 1-2 shift sol ctrl
- 12 volt battery
- 12 volt ignition
- 2-3 shift sol
- 2-3 shift sol ctrl
- 5 volt sens ref
- A12
- B10
- B11
- Brake signal
- C11
- Coolant temp in
- Coolant temp sensor (top front of engine, on intake manifold)
- D15
- D16
- Dlc
- Electronic 4-speed automatic overdrive transmission
- Fuse ecm batt 10a
- Fuse ecm ign 10a
- Fuse trans 10a
- G115 (rear of engine near distributor)
- G125 (front of engine near thermostat)
- Hot at all times
- Hot in run
- I/p fuse block
- Input speed hi
- Input speed lo
- Module (pcm)
- Or start
- Output speed sensor (left rear of transmission)
- Pnk
- Powertrain control
- Press ctrl sol hi
- Press ctrl sol lo
- Press sw a
- Press sw b
- Press sw c
- Pressure control solenoid
- Pressure switch manifold
- Red
- Sens grd
- Serial data
- System ground
- Tcc driver
- Tcc sol
- Tcc/brake switch (on brake pedal support arm)
- Throttle position sensor (right side of throttle body)
- Tp sens in
- Trans input speed sensor (left front of transmission)
- Trans- mission temp sensor
- Transmission temp in
- Vehicle speed sensor buffer (park brake support bracket)
- Vss input
WIPER/WASHER
Wiper/Washer Wiring Diagram for Chevrolet Hi-Cube G30 1993
List of elements for Wiper/Washer Wiring Diagram for Chevrolet Hi-Cube G30 1993:
- (w/ l19)
- Control area
- Delay/ speed/ wash control
- Fuse block
- G115 (right rear of cyl head) (w/o l19)
- G125 (left front of engine)
- G202 (at bus bar ground)
- Hot in accy or run
- Ign
- Low
- Mist
- Off
- Park switch
- Pnk
- Pulse
- Wash switch
- Washer motor
- Windshield wiper motor module (center rear of engine compt)
- Wiper fuse 25a
- Wiper/ washer switch