AIR CONDITIONING
Automatic A/C Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Automatic A/C Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005:
- (at front of right fender) g109
- (near breakout to passenger air bag deactivation indicator) s210
- A/c demand sig
- Air temp door resistor sig
- Amb temp sens input
- Ambient air temperature sensor (on front of upper radiator support)
- Analog
- Battery
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Blend door +/-
- Blower motor high
- Blower motor relay
- C220a
- C2220b
- C228a
- C228b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Digital
- Ect ind
- Electronic automatic temperature control (eatc) module (behind center of dash)
- Electronic cluster
- Eng/met
- Engine coolant temperature (ect) sensor (on top right front of engine, near fuel injector 1)
- Front blower motor (at right rear of engine compt)
- Front blower motor speed controller (at rear of engine compt)
- Fuse 10a
- Fuse 15a
- Fuse 40a
- G108 (at front of right fender)
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- Ground
- High blower
- Hot at all times
- Hot in run
- Hot in run or start
- In car temp sens
- In-vehicle temperature sensor (behind center of dash)
- Instrument cluster (analog)
- Instrument cluster (digital)
- Instrument illum
- Interior lights system
- Micro- processor
- Red
- Remote ctrl unit
- S203 (in main body wiring harness, near breakout to instrument cluster)
- S207 (in main wiring harness, near breakout to rear window defrost switch)
- Scp bus (+)
- Scp bus (-)
- Sig rtn
- Speed ctrl
- Sunload sens input
- Temp door sig +
- Vbc input
- Vbc output
- Vpwr
Automatic A/C Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005
List of elements for Automatic A/C Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005:
- (at base of steering column) air bag sliding contact
- (in engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (in main wiring harness, near breakout to passenger air bag deactivation indicator)
- (not
- A/c clutch field coil (at right front of engine)
- A/c clutch relay
- A/c compressor clutch diode
- A/c evaporator discharge air temperature sensor (on right side rear of engine compt)
- A/c pressure transducer sensor (on right side center of engine)
- Audio/climate control switch
- Autolamp/sunload sensor (on upper left side of dash)
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- C1048a
- C1048b
- C175b
- C175e
- C175t
- C2145b
- C218a
- C218b
- C2208
- C290a
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Fan down
- Fan up
- Fuse 15a
- Fuse 50a
- G102 (at front of left fender)
- G109 (at front of right fender)
- G110 (right side of engine)
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- Ground
- Hot at all times
- Hot in start or run
- Lighting control module (behind center of dash)
- Low charge protection switch (at right side of engine compt)
- Phone
- Powertrain control module (pcm) (left rear of engine compt)
- Radio
- Red
- Rest
- S111 (in dash panel to headlamp junction harness, left rear of engine compt)
- S121
- S123
- S126 (in engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- S130 (in dash panel to headlamp junction harness, left rear of engine compt)
- S157 (in engine control sensor & fuel charge wiring harness, near breakout to c192)
- S201 (in main wiring harness, in breakout to adjustable pedal switch)
- S210
- S294 (in steering column control switch jumper harness)
- Temp down
- Temp up
- Temperature blend door actuator (behind right side of dash, on top of a/c plenum)
- Used)
- Vbatt
Manual A/C Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Manual A/C Wiring Diagram for Ford Crown Victoria S 2005:
- (at rear of engine compt) front blower motor resistor assembly
- (at right rear of engine compt) front blower motor
- (in dash panel to
- (in engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (in main wiring harness, near breakout to passenger air bag deactivation indicator) s210
- (left rear of engine compt)
- (not used)
- A/c clutch field coil (at right front of engine)
- A/c clutch relay
- A/c compressor clutch diode
- A/c evaporator discharge air temperature sensor (on right side rear of engine compt)
- A/c pressure transducer sensor (on right side center of engine)
- A/c sw max
- Analog
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Blower motor relay
- Blower motor switch
- C1048a
- C1048b
- C175b
- C175e
- C220a
- C2220b
- C294a
- C294b
- C294c
- C294d
- Central junction box (cjb) (below dash, left of steering column)
- Cold
- Ctrl
- Defrost
- Defrost defrost/floor
- Defrost/floor
- Digital
- Early production
- Ect ind
- Engine coolant temperature (ect) sensor (on top right front of engine, near fuel injector 1)
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Floor
- Function selector switch assembly
- Fuse 10a
- Fuse 15a
- Fuse 40a
- Fuse 50a
- G102 (at front of left fender)
- G108 (at front of right fender)
- G109 (at front of right fender)
- G110 (right side of engine)
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- G204 (behind right kick panel)
- Ground
- Headlamp junction harness, near breakout to battery junction box)
- High
- Hot at all times
- Hot in run
- Hot in start or run
- Illumination
- Instrument cluster (analog)
- Instrument cluster (digital)
- Interior lights system
- Late production
- Low
- Low charge protection switch (at right side of engine compt)
- Med high
- Med low
- Mode switch
- Off
- Off off panel
- Panel
- Panel/floor
- Powertrain control module (pcm)
- Red
- S111 (in dash panel to headlamp junction harness, left rear of engine compt)
- S121
- S121 (in dash panel to headlamp junction harness, near breakout to battery junction box)
- S122
- S123
- S126 (in engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- S130 (in dash panel to headlamp junction harness, left rear of engine compt)
- S157 (in engine control sensor & fuel charge wiring harness, near breakout to c192)
- S207 (in main wiring harness, near breakout to rear window defrost switch)
- S209
- S276 (in main wiring harness, near breakout to instrument cluster)
- Temp ctrl potentiometer
- Temperature blend door actuator (behind right side of dash, on top of a/c plenum)
- Vbatt
- Vpwr
- Warm
ANTI-LOCK BRAKES
Anti-lock Brakes Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Anti-lock Brakes Wiring Diagram for Ford Crown Victoria S 2005:
- (at front of left fender) g103
- (in dash panel to headlamp junction harness, near breakout to pcm) s103
- Abs control module (at left front of engine compt)
- Abs ind
- Analog
- Battery
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Bpp switch
- Brake pedal position switch (top of brake pedal support)
- C175b
- C2145b
- C220c
- C2220a
- C2220b
- Can bus +
- Can bus -
- Can bus+
- Can bus-
- Central junction box (cjb) (below dash, left of steering column)
- Computer
- Computer data lines system
- Data lines
- Digital
- Fuse 10a
- Fuse 20a
- Fuse 40a
- G203 (behind right kick panel)
- Ground
- Hot at all times
- Hot in run
- Hot in run or start
- Illumination
- Ind sig
- Indicator
- Instrument cluster
- Instrument cluster system
- Interior lights system
- Left front wheel speed sensor (at left side of engine compt)
- Left rear wheel speed sensor (forward of left rear wheelwell)
- Lf sensor+
- Lf sensor-
- Lighting control module (left rear of engine compt)
- Lr sensor+
- Lr sensor-
- On/off ind
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- Red/pnk
- Rf sensor+
- Rf sensor-
- Right front wheel speed sensor (at right side of engine compt)
- Right rear wheel speed sensor (forward of right rear wheelwell)
- Rr sensor+
- Rr sensor-
- S101
- S201
- S237
- S276
- System
- Tc sw sig
- Trac ctrl ind
- Trac ind
- Traction control switch
- Vpwr
- Warning lamps module (behind left side of dash)
ANTI-THEFT
Anti-theft Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Anti-theft Wiring Diagram for Ford Crown Victoria S 2005:
- (in main wiring harness, in breakout to data link connector) s296
- (in main wiring harness, in breakout to data link connector) s297
- Auto lamp/sunload sensor (on upper left side of dash)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175b
- C175t
- Central junction box (cjb) (below dash, left of steering column)
- Data link connector (dlc) (behind left side of dash)
- Except police vehicle
- Fuse 10a
- G201 (behind right kick panel)
- Ground
- Hot at all times
- Hot in start or run
- Passive anti-theft transceiver
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compt)
- S203
- S210
- Scp +
- Scp -
- Starter relay
- Vpwr
BODY CONTROL MODULES
Body Control Modules Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Body Control Modules Wiring Diagram for Ford Crown Victoria S 2005:
- (behind right kick panel) g201
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- C2145a
- C2145b
- C220b
- C501a
- C501b
- C501c
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Cruise control system
- Digital cluster
- Door locks system
- Driver door module (bottom front of left front door)
- Fuse 10a
- Fuse 20a
- Fuse 5a
- G212 (at left kick panel)
- Hot at all times
- Hot in run
- Hot in start
- Instrument cluster
- Lighting control module (behind center of dash)
- S217
- S262
- S277 (near breakout to lighting control module)
- S500
COMPUTER DATA LINES
Computer Data Lines Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Computer Data Lines Wiring Diagram for Ford Crown Victoria S 2005:
- (bottom front of left front door) driver door module
- (in dash panel to headlamp junction harness, near breakout to g102)
- (in main body wiring harness, near breakout to variable assist power steering module)
- (in main wiring harness, in breakout to data link connector)
- (in main wiring harness, in breakout to data link connector) s271
- (late production)
- (late production) s218
- (w/ roof opening panel) s219
- Abs control module (at left front of engine compartment)
- Air suspension module (behind right side of dash, above glove box)
- C175b
- C175t
- C2131a
- C2145a
- C2231a
- C228a
- C310a
- C501a
- C9013a
- Can+
- Can-
- Central junction box (cjb) (below dash, left of steering column)
- Data link connector (dlc) (behind left side of dash)
- Electronic automatic temperature control (eatc) module (behind center of dash)
- Fuse 20a
- G107 (at left rear of engine compt)
- G203 (behind right kick panel)
- Hot at all times
- Iso
- Lighting control module (below center of dash)
- Overhead console (w/ roof opening panel)
- Peps
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compartment)
- Restraints control module (below center of dash)
- S105
- S106
- S118
- S201
- S216
- S296
- S297
- Scp+
- Scp-
- Variable assist power steering (vaps) module (behind right side of dash, above glove box)
- W/ air suspension
- W/ police
- W/ roof opening panel) s225
- W/o air suspension
- W/o police
COOLING FAN
Cooling Fan Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Cooling Fan Wiring Diagram for Ford Crown Victoria S 2005:
- (behind right
- (digital) instrument cluster
- (left rear of engine compt) powertrain control module (pcm)
- Analog
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C1048a
- C1048b
- C175e
- C220a
- C2220b
- Central junction box (cjb) (below dash, left of steering column)
- Ctrl
- Digital
- Ect ind
- Engine coolant temperature (ect) sensor (on top right front of engine, near fuel injector 1)
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Fuse 10a
- Fuse 50a
- G102 (at front of left fender)
- Ground
- Hot at all times
- Hot in run
- Hot in start or run
- Instrument cluster (analog)
- Kick panel) g201
- Micro- processor
- Red
- S210
- S276
- Vbatt
- Vpwr
CRUISE CONTROL
Cruise Control Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Cruise Control Wiring Diagram for Ford Crown Victoria S 2005:
- (in dash panel to headlamp junction harness, near breakout to pcm) s103
- (in main body wiring harness, near breakout to g212)
- Abs control module (at left front of engine compt)
- Accelerator pedal position sensor (under left side of dash)
- Air bag sliding contact (at base of steering column)
- Bpp sw
- Brake pedal position switch (top of brake pedal support)
- Brake shift interlock (on steering column)
- C175b
- C175e
- C175t
- C2145b
- C218a
- C218b
- C2330a
- C2330b
- C501a
- Central junction box (cjb) (below dash, left of steering column)
- Coast
- Deactivator sw
- Deactivator switch
- Driver door module (bottom front of left front door)
- Electronic throttle control (etc) motor (left side of engine)
- Etc motor +/-
- Fuse 10a
- G212 (at left kick panel)
- Hot at all times
- Illumination
- Interior lights system
- Lighting control module (behind center of dash)
- Off
- Oss sig
- Output shaft speed (oss) sensor (on left side of transmission)
- Powertrain control module (pcm) (left rear of engine compartment)
- Resume
- S147 (in engine control sensor & fuel charge wiring harness, near breakout to pcm)
- S225 (in main body wiring harness, near breakout to variable assist power steering module)
- S237
- S256
- S267
- S292
- S292 (in steering wheel control switch jumper harness)
- S293
- S295 (in steering wheel control switch jumper harness)
- Sensor 1 sig
- Sensor 2 sig
- Sensor 3 sig
- Set
- Set +
- Set -
- Sig rtn
- Steering wheel/speed control switch
- Throttle position sensor (tps) (on left side of engine)
- Tps sig 1
- Tps sig 2
- Vref
- W/ center console
- W/ steering wheel audio climate control switch
- W/o center console
- W/o steering wheel audio climate control switch
DEFOGGERS
Defoggers Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Defoggers Wiring Diagram for Ford Crown Victoria S 2005:
- (in main body wiring harness, near breakout to c213) s228
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145b
- C402a
- C402b
- Central junction boc (cjb) (below dash, left of steering column)
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Fuse 40a
- G200 (w/ power seats) (behind right kick panel)
- G203 (behind right kick panel)
- G209 (w/o power seats) (behind right kick panel)
- G212 (at left kick panel)
- G400 (at right rear of luggage compartment)
- Hot at all times
- Hot in on or start
- Illum switch
- Interior lights system
- Left exterior rear view mirror
- Lighting control module (behind center of dash)
- Nca
- Off
- On ind defroster
- Rear window defrost grid
- Rear window defrost relay
- Rear window defrost switch
- Right exterior rear view mirror
- S207
- S252 (in main wiring harness, near breakout to left footwell courtesy lamp)
- S276
- S500 (w/ keyless entry)
- S501 (w/o keyless entry)
- S600
ELECTRONIC POWER STEERING
Electronic Power Steering Wiring Diagram, with Air Suspension for Ford Crown Victoria S 2005
List of elements for Electronic Power Steering Wiring Diagram, with Air Suspension for Ford Crown Victoria S 2005:
- Air suspension module (behind right side of dash, above glove box)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175t
- C2131a
- C2131b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Fuse 10a
- G201 (behind right kick panel)
- Ground
- Hot at all times
- Hot in run
- Power steering valve solenoid (on left front side of engine)
- Powertrain control module (pcm) (left rear of engine compartment)
- S221
- S231 (in main wiring harness, near breakout to g200)
- Scp+
- Scp-
- Vbatt
- Vpwr
- Vss
- Vss (+)
Electronic Power Steering Wiring Diagram, without Air Suspension for Ford Crown Victoria S 2005
List of elements for Electronic Power Steering Wiring Diagram, without Air Suspension for Ford Crown Victoria S 2005:
- (behind right kick panel) g210
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175t
- C2231a
- C2231b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Fuse 10a
- Ground
- Hot at all times
- Hot in run
- Power steering valve solenoid (on left front side of engine)
- Powertrain control module (pcm) (left rear of engine compartment)
- S221
- S231 (in main wiring harness, near breakout to g200)
- Scp+
- Scp-
- Signal rtn
- Sw pwr
- Variable assist power steering (vaps) module (behind right side of dash, above glove box)
- Vbatt
- Vpwr
- Vss +
ELECTRONIC SUSPENSION
Electronic Suspension Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Electronic Suspension Wiring Diagram for Ford Crown Victoria S 2005:
- (at front of left fender) g105
- (behind center of dash) lighting control module
- (in main body wiring harness, near breakout to c423) s450
- (in right front of engine compt, behind battery) battery junction box (bjb)
- Air suspension compressor assembly (at left front side of engine compt)
- Air suspension compressor relay
- Air suspension disable switch
- Air suspension height sensor (under rear of vehicle attached to control arm)
- Air suspension indicator
- Air suspension module (behind right side of dash, above glove box)
- Analog cluster
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175t
- C2131a
- C2131b
- C2145a
- C220b
- C2220a
- Central junction box (cjb) (below dash, left of steering column)
- Compressor
- Computer data lines system
- Digital
- Electronic power steering system
- Fuse 10a
- Fuse 30a
- G102 (at front of left fender)
- G210 (behind right kick panel)
- G405 (at rear center of luggage compartment)
- Hot at all times
- Hot in run
- Instrument cluster
- Left rear air spring solenoid valve (at left rear of vehicle)
- Nca
- Pnk
- Powertrain control module (pcm) (left rear of engine compt)
- Pwr
- Red
- Right rear air spring solenoid valve (at right rear of vehicle)
- S112
- S113
- S120
- S221
- S231 (w/ overhead console) (near breakout to g200)
- Scp+
- Scp-
- Sig rtn
- Vbatt
- Vent
- Vpwr
- Vss
EMERGENCY VEHICLE SYSTEMS
Fire Suppression Wiring Diagram, Police Option for Ford Crown Victoria S 2005
List of elements for Fire Suppression Wiring Diagram, Police Option for Ford Crown Victoria S 2005:
- C2220a
- C3281a
- C3281b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Fire suppression manual switch
- Fire suppression module (under rear seat)
- Fsil c2220
- Fuse 10a
- G408 (at rear center of luggage compt)
- Hot in run or start
- Instrument cluster
- Left fire suppressor (front of trunk, at left side)
- Nca
- Nca hs can+
- Nca lhsr nca lhsf nca fsil nca gnd nca hs can- nca iso9141 nca mas high nca mas low nca rhsf nca rhsr nca
- Nca r/s nca
- Nca rhrsr nca rhrsf nca lhrsr nca lhrsf
- Pin shorting bars engaged when module connector is disconnected from harness: (shorting bars are connected between following pins: 4-5, 6-7 & 12-13 c3281a 1-2 & 3-4 c3281b)
- Right fire suppressor (front of trunk, at right side)
- S234
- Shorting bar
ENGINE PERFORMANCE
Engine Performance Wiring Diagram (1 of 5) for Ford Crown Victoria S 2005
List of elements for Engine Performance Wiring Diagram (1 of 5) for Ford Crown Victoria S 2005:
- A/c clutch rly
- A/c pre sen sig
- Abs ind
- Accelerator pedal position sensor (under left side of dash)
- Air conditioning system
- Anti-lock brakes system
- App sen sig 2
- App sen sig 3
- Apps sig 1
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Brk pedal sw
- C175b
- Can bus +
- Can bus -
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Cruise control system
- Evap can vent
- Feps
- Floor shifter (in center console)
- Fpm
- Fuel level data
- Fuse 10a
- Fuse 15a
- Fuse 30a
- G106 (at left rear of engine compt)
- G107 (at left rear of engine compt)
- G109 (at front of right fender)
- G110 (right side of engine)
- Gnd
- Heated pvc (on top right front of engine)
- Hot at all times
- Hot in run
- Hot in run or start
- Ign coils relay
- Instrument cluster system
- Intake sen sig
- Low charge sw
- Maf sens sig
- Maf/iat sen
- Mfp
- On/off ind sw
- Overdrive cancel switch
- Pcm power diode
- Pcm power relay
- Powertrain control module (pcm) (left rear of engine compt)
- Rdi
- Red
- Red/pnk
- Rtn sig
- S101
- S118
- S121
- S157
- S164
- S276
- Sig rtn
- Starter relay
- Starting/charging system
- Temp sens sig
- Traction ctrl ind
- Trans ctrl sw
- Vapor valve
- Vbatt
- Vpwr
- Vref
- W/ center console
- W/o center console
Engine Performance Wiring Diagram (2 of 5) for Ford Crown Victoria S 2005
List of elements for Engine Performance Wiring Diagram (2 of 5) for Ford Crown Victoria S 2005:
- (behind right side of dash, above glove box)
- (in dash panel to headlamp junction
- (in dash panel to headlamp junction harness, near breakout to battery junction box)
- (in main body wiring harness, near breakout to g212)
- (left rear of engine compt)
- A/c clutch relay
- A/c evaporator discharge air temperature sensor (right side rear engine compt)
- Air suspension module
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2131b
- C2145b
- C220a
- C2231b
- C290a
- C930
- Ends in harness console
- Ends in harness passenger side in foot well
- Evaporative emission (evap) canister vent valve (in center rear of luggage compt)
- Fuel pump relay
- Fuse 10a
- Fuse 15a
- Fuse 20a
- G107 (at left rear of engine compt)
- G109 (at front of right fender)
- Harness, near breakout to c1019)
- Hot at all times
- Inertia fuel shut-off (ifs) switch (in luggage compt, on left support)
- Lighting control module (behind center of dash)
- Mass air flow/intake air temperature (maf/iat) sensor (behind air cleaner assembly)
- Overhead console
- Radio
- Red
- Red/pnk
- S111 (left rear of engine compt)
- S117
- S118
- S119
- S121
- S130
- S231 (in main wiring harness, near breakout to g200)
- S247 (near breakout to c410)
- S256
- Vapor management valve (right rear of engine)
- Variable assist power steering (vaps) module
- Vhcl spd input
- W/ air suspension
- W/ overhead console
- W/ roof opening panel
- W/o air suspension
- W/o roof opening panel
Engine Performance Wiring Diagram (3 of 5) for Ford Crown Victoria S 2005
List of elements for Engine Performance Wiring Diagram (3 of 5) for Ford Crown Victoria S 2005:
- (at right front of engine) power steering pressure switch
- (in engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- (in engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (in engine control sensor & fuel charge wiring harness, near breakout to turbine shaft speed sensor) s146
- (on left front side of luggage compt) fuel pump driver module
- (on right side center of engine) a/c pressure transducer sensor
- (on top left front of engine) cylinder-head temperature sensor
- (on top right side of engine) fuel rail pressure/ temperature sensor
- (right side of engine) egr system module (esm)
- Digital transmission range (dtr) sensor (on left side of transmission)
- Dpfe
- Evp
- Frp
- Frt
- Fuel tank unit (in fuel tank)
- G201 (behind right kick panel)
- G406 (at rear center of luggage compt)
- Heated oxygen sensor (ho2s) 11 (lower right rear of engine, in exhaust manifold)
- Heated oxygen sensor (ho2s) 12 (in exhaust, rear of catalyst)
- Heated oxygen sensor (ho2s) 21 (lower left rear of engine, in exhaust manifold)
- Heated oxygen sensor (ho2s) 22 (in exhaust, rear of catalyst)
- Map
- Nca
- R n
- Red
- Red/pnk
- S123
- S126
- S210
- S405
- Sig
- Vpwr
- Vref
Engine Performance Wiring Diagram (4 of 5) for Ford Crown Victoria S 2005
List of elements for Engine Performance Wiring Diagram (4 of 5) for Ford Crown Victoria S 2005:
- (in breakout to instrument cluster)
- (near breakout to pcm) s147
- (top right front of engine, near fuel injector 1) engine coolant temperature (ect) sensor
- 4r70w transmission control solenoids
- Analog
- Anti-theft ind
- Anti-theft system
- Battery ind
- C175t
- C220a
- C220c
- C2220a
- C2220b
- Check guage (or) fail-safe cool ind
- Check ind
- Computer data lines system
- Cruise ind
- Cylinder head
- Digital
- Electronic pressure control solenoid
- Eng vacuum
- Engine coolant temp input
- Epcs ctrl
- Etcil ind
- Fuel cap ind
- Fuel level ind
- Fuel pump sig
- G201 (behind right kick panel)
- Gen comm
- Ho2s 12
- Ho2s 22
- Instrument cluster
- Instrument cluster system
- Malfunction indicator input
- Oss sensor
- Output shaft speed (oss) sensor (on left side of transmission)
- Overdrive ind
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- S202
- S210
- Scp bus +
- Scp bus -
- Shift sol a
- Shift sol b
- Shift solenoids
- Sig rtn
- Ssa
- Ssb
- Starting/ charging system
- Tcc sol
- Tcil ind
- Tft sens sig
- Torque converter clutch solenoid
- Tr1
- Tr2
- Tr3a
- Tr4
- Transmission fluid temperature sensor
- Tss sen sig
- Turbine shaft speed (tss) sensor (left side of transmission)
- Veh spd sig
- Vehicle speed input
Engine Performance Wiring Diagram (5 of 5) for Ford Crown Victoria S 2005
List of elements for Engine Performance Wiring Diagram (5 of 5) for Ford Crown Victoria S 2005:
- (below ignition transformer capacitor) camshaft position sensor
- (on left side of engine) throttle position sensor (tps)
- +/-
- C175e
- Cam pos sens
- Ckp+
- Ckp-
- Coil on plugs (coil 1: on right front of engine) (coil 2: on right center of engine) (coil 3 & 4: on right rear of engine) (coil 5 & 6: on left front of engine) (coil 7: on left center of engine) (coil 8: on left rear of engine)
- Cooling fans system
- Crankshaft position sensor (on lower right front of engine)
- Dpfe
- Electronic throttle control (etc) motor (left side of engine)
- Evr ctrl
- Fan low rly
- Frp
- Frt
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuel injectors (inj 1: at right front of engine) (inj 2 & 3: at right center of engine) (inj 4: at right rear of engine) (inj 5: at left front of engine) (inj 6 & 7: at left center of engine) (inj 8: at left rear of engine)
- G107 (at left rear of engine compt)
- Ho2s 11
- Ho2s 21
- Ign coil 1
- Ign coil 2
- Ign coil 3
- Ign coil 4
- Ign coil 5
- Ign coil 6
- Ign coil 7
- Ign coil 8
- Ignition transformer capacitor (left front of engine)
- Knock sensor (on right front of engine)
- Ks+
- Ks-
- Map
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- Red/pnk
- S118
- S136 (in engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- Sig rtn
- Tan
- Tan/red
- Tps sig 1
- Tps sig 2
- Vref
EXTERIOR LIGHTS
Accessory Lamps Wiring Diagram, Crown Police (1 of 3) for Ford Crown Victoria S 2005
List of elements for Accessory Lamps Wiring Diagram, Crown Police (1 of 3) for Ford Crown Victoria S 2005:
- (at breakout for police luggage compt relay/fuse center)
- (at breakout for police luggage compt relay/fuse center) s479
- (in breakout to police trunk relay/fuse center)
- (not used)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C1365a
- C1365b
- Central junction box (cjb) (below dash, left of steering column)
- End in harness, glove box
- Ends in harness, glove box
- Ends in harness, trunk
- Fuse 50a
- Fuse a1 10a
- Fuse a2 5a
- Fuse a3 5a
- Fuse a4 10a
- Fuse a5 10a
- Fuse a6 10a
- Fuse b1 5a
- Fuse b2 10a
- Fuse b3 5a
- Fuse b4 10a
- Fuse b5 10a
- Fuse b6 10a
- Fuse b7 20a
- G411 (in luggage compt)
- Headlights system
- Horns system
- Hot at all times
- Nca
- Pnk
- Police glove box relay/ fuse center (in glove box)
- Police trunk relay/fuse center (in luggage compt)
- Relay
- Right front ends in harness fender
- S283
- S284
- S285
- S286
- S288
- S291
- S470
- S472 (in power distribution wiring harness, in breakout to police trunk relay/fuse center)
- S474
- S476
- S478
- S487 (near breakout for c422)
- Seat) g402
- Tan
- Wig wag module (right side of engine compt)
Accessory Lamps Wiring Diagram, Crown Police (2 of 3) for Ford Crown Victoria S 2005
List of elements for Accessory Lamps Wiring Diagram, Crown Police (2 of 3) for Ford Crown Victoria S 2005:
- (in breakout to police trunk relay/ fuse center) s464
- (in emergency jumper wiring harness, near breakout for c422) s475
- (in luggage compt)
- (in luggage compt) strobe control module
- 10a
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C4231a
- C4231b
- C4231c
- C4231d
- C4231e
- C4231f
- C4231g
- C4231h
- C4231j
- Ends in harness, trunk
- From s468 (diagram 3 of 3)
- Fuse 40a
- Fuse c11 20a
- Fuse c12 10a
- G411
- G411 (in luggage compt)
- Hot at all times
- Inline fuse
- Left front strobe assembly (left front of engine compt)
- Left grille strobe assembly (behind left side of grille)
- Left rear strobe assembly
- Nca
- Pnk
- Police light bar relay/fuse center (in front of luggage compt)
- Police power relay
- Rear deck led flasher
- Red
- Right front strobe assembly (right front of engine compt)
- Right grille strobe assembly (behind right side of grille)
- Right rear strobe assembly
- S298
- S355 (in emergency jumper wiring harness, near breakout for strobe/light bar control switch)
- S460 (in emergency jumper wiring harness, near breakout for c411)
- S465
- S480 (near breakout for strobe control module)
- S482 (near breakout for strobe control module)
- S484 (near breakout for
- S486 (near breakout for strobe control module)
- S488
- S490
- Strobe control module)
- Trunk air circulation fan motor (in luggage compt)
Accessory Lamps Wiring Diagram, Crown Police (3 of 3) for Ford Crown Victoria S 2005
List of elements for Accessory Lamps Wiring Diagram, Crown Police (3 of 3) for Ford Crown Victoria S 2005:
- (behind right rear seat) g402
- (in breakout to police light bar relay/fuse center)
- (in luggage compt) siren amplifier
- (in power distribution wiring harness, in breakout to police light bar relay/fuse center) s466
- Battery
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C3257a
- C3257b
- Central junction box (cjb) (below dash, left of steering column)
- Ends in harness, (trunk) low band radio
- Ends in harness, center console
- Ends in harness, trunk
- Front flasher
- Fuse 50a
- Fuse c1 10a
- Fuse c2 10a
- Fuse c3 10a
- Fuse c4 10a
- Fuse c5 10a
- Fuse c6 10a
- Fuse c7 10a
- Fuse c8 10a
- G411 (in luggage compt)
- Horns system
- Hot at all times
- Left front ends in harness, fender
- Left front ends in harness, footwell
- Pnk
- Police accessory connector
- Police accessory relay
- Police light bar relay/ fuse center (in front of luggage compt)
- Red
- Red/ pnk
- Relay
- Right front ends in harness, fender
- Right front ends in harness, grille
- S299
- S350
- S462
- S465
- S468 (in power distribution wiring harness, in breakout to police light bar relay/ fuse center)
- S469
- Siren 1
- Strobe/light bar control
- Switches
- Tan
- To fuse c12 (diagram 2 of 3)
Accessory Lamps Wiring Diagram, with Police Option for Ford Crown Victoria S 2005
List of elements for Accessory Lamps Wiring Diagram, with Police Option for Ford Crown Victoria S 2005:
- (at rear center of luggage compt) g406
- (behind center
- (in emergency jumper wiring harness, near breakout for g411) s460
- (in luggage compt wiring harness, near breakout to c405) s433
- (in main wiring harness, near breakout to passenger air bag deactivation indicator)
- (near breakout to passive anti-theft transceiver) s273
- (not used)
- 10a
- B6 c2319
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C202a
- C202c
- C2145c
- C2319
- C3257a
- C4170a
- C4170b
- Central junction box (cjb) (below dash, left of steering column)
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (in left rear of luggage compt)
- Ends in harness (center console)
- Exterior lamps circuit
- Fuse 10a
- Fuse 20a
- Fuse 25a
- Fuse 40a
- Fuse 50a
- Fuse b1 15a
- Fuse b2 15a
- Fuse b3 15a
- Fuse b4 2a
- Fuse b5 2a
- Fuse b6 2a
- G109 (at front of right fender)
- G403 (behind right rear seat)
- G411 (in luggage compt)
- Hot at all times
- Hot in run or acc
- Inline fuse
- Interior lights system
- Left front ends harness (foot-well)
- Left rear police flasher lamp
- Left rear police tray lamp
- Left side spot lamp
- Lighting control
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Module
- Multi-function switch
- Of dash)
- Passenger side ends harness (foot-well)
- Pnk
- Police option fuse holder (in glove box)
- Police power relay
- Rear flasher
- Rear flasher relay
- Rear police auxiliary junction box (behind bottom center of rear seats)
- Red
- Right rear police flasher lamp
- Right rear police tray lamp
- Right side spot lamp
- S110
- S121
- S211 (near breakout to passenger air bag module)
- S222
- S224
- S243 (in main wiring harness, in breakout to instrument cluster)
- S290
- S403
- S406 (in main body wiring harness, near breakout to c423)
- S422 (in main body wiring harness, near breakout to c423)
- S465
- Strobe/light bar control switches
- Trunk air circulation fan motor (in luggage compt)
- Trunk, tailgate fuel doors system
Back-up Lamps Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Back-up Lamps Wiring Diagram for Ford Crown Victoria S 2005:
- (at rear center of luggage compt) g406
- Central junction box (cjb) (below dash, left of steering column)
- Digital transmission range (dtr) sensor (on left side of transmission)
- Electrochromatic inside mirror unit
- Fuse 10a
- Hot in run or start
- Left reversing lamp
- Right reversing lamp
- S420
- W/auto-dimming interior mirror unit
Exterior Lamps Wiring Diagram, with Police Option (1 of 2) for Ford Crown Victoria S 2005
List of elements for Exterior Lamps Wiring Diagram, with Police Option (1 of 2) for Ford Crown Victoria S 2005:
- (at right rear of luggage compt)
- (behind right kick panel)
- (near breakout to ambient air temperature sensor) s109
- Accessory lamps circuit
- Auto
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Brake pedal position switch (top of brake pedal support)
- C202a
- C202c
- C205a
- C2145a
- C2145b
- C2145c
- C2220a
- C2220b
- C526a
- C526b
- Central junction box (cjb) (below dash, left of steering column)
- Driver side front door ajar switch (top rear of left front door)
- Fuse 10a
- Fuse 15a
- Fuse 20a
- G102 (at front of left fender)
- G109 (at front of right fender)
- G109 (front of right fender)
- G203
- G203 (behind right kick panel)
- G401
- G406 (rear center of luggage compt)
- Head
- High mounted stoplamp (grand marquis)
- Hot at all times
- Hot in run
- Instrument cluster
- Left front cornering lamp (grand marquis)
- Left front park/ turn lamp
- Left front parking lamp (crown victoria)
- Left turn
- Left turn ind
- License lamp
- Lighting control module (behind center of dash)
- Main light switch
- Maj
- Multi-function switch
- Nca
- Off
- Park
- Pwr
- Red
- Right front cornering lamp (grand marquis)
- Right turn
- Right turn ind
- S107
- S108
- S112
- S159
- S201
- S207
- S238
- S243 (in main wiring harness, in breakout to instrument cluster)
- S244 (in main wiring harness, in breakout to instrument cluster)
- S257 (main wiring harness, in breakout to instrument cluster)
- S273 (near breakout to passive anti-theft transceiver)
- S402
- S420
- S427 (in main body wiring harness, near breakout to c410)
- Vbatt
- Vpwr
- Vref
Exterior Lamps Wiring Diagram, with Police Option (2 of 2) for Ford Crown Victoria S 2005
List of elements for Exterior Lamps Wiring Diagram, with Police Option (2 of 2) for Ford Crown Victoria S 2005:
- (at front of right fender)
- (behind right kick panel)
- (early production) s281
- (in rear lamp wiring harness, in breakout to c410)
- (no connection)
- C2212a
- C2212b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Central junction box (cjb) (below dash, left of steering column)
- Door ajar indicator
- Driver side rear door ajar switch (at rear of left rear door)
- Early
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (in left rear of luggage compt)
- Fuse 15a
- G109
- G109 (at front of right fender)
- G204
- G410 (in luggage compartment)
- Hot at all times
- Late
- Left rear park/stop/ turn lamp 1
- Left rear park/stop/ turn lamp 2
- Maj
- Min
- Passenger side front door ajar switch (at top rear of right front door)
- Passenger side rear door ajar switch (at rear of right rear door)
- Production
- Right front park/ turn lamp
- Right front parking lamp (crown victoria)
- Right rear park/stop/ turn lamp 1
- Right rear park/stop/ turn lamp 2
- Roof ends in harness
- S114
- S158
- S204 (late production)
- S226
- S227 (late production)
- S238
- S259 (in main body wiring harness, near breakout to g200)
- S282 (early production)
- S400
- S401
- S406 (in main body wiring harness, near breakout to c423)
- S413
- S414
- S416
- S422 (in main body wiring harness, near breakout to c423)
- S442
- Taxi roof lamp
- Taxi roof lamp switch
Exterior Lamps Wiring Diagram, without Police Option (1 of 2) for Ford Crown Victoria S 2005
List of elements for Exterior Lamps Wiring Diagram, without Police Option (1 of 2) for Ford Crown Victoria S 2005:
- (at right rear of luggage compt) g401
- (behind right kick panel)
- (in main body wiring harness, near breakout to c410) s427
- (near breakout to ambient air temperature sensor)
- (near breakout to c1010) s116
- Analog
- Auto
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Brake pedal position switch (top of brake pedal support)
- C202a
- C202c
- C205a
- C2145a
- C2145b
- C2145c
- C220c
- C2220a
- C2220b
- C526a
- C526b
- Central junction box (cjb) (below dash, left of steering column)
- Crown victoria
- Digital
- Driver side front door ajar switch (at top rear of left front door)
- Fuse 10a
- Fuse 15a
- Fuse 20a
- G102 (at front of left fender)
- G109 (at front of right fender)
- G203
- G203 (behind right kick panel)
- G406 (at rear center of luggage compt)
- Grand marquis
- Head
- High mounted stoplamp (grand marquis)
- Hot at all times
- Hot in run
- Instrument cluster
- Left front cornering lamp (grand marquis)
- Left front park/ turn lamp
- Left front parking lamp
- Left turn
- Left turn ind
- License lamp
- Lighting control module (behind center of dash)
- Main light switch
- Maj
- Microprocessor
- Min
- Multi-function switch
- Nca
- Off
- Park
- Pwr
- Red
- Right front cornering lamp (grand marquis)
- Right turn
- Right turn ind
- S107
- S108
- S109
- S112
- S159
- S201
- S207
- S238
- S402
- S420
- Vbatt
- Vpwr
- Vref
Exterior Lamps Wiring Diagram, without Police Option (2 of 2) for Ford Crown Victoria S 2005
List of elements for Exterior Lamps Wiring Diagram, without Police Option (2 of 2) for Ford Crown Victoria S 2005:
- (at front of right fender)
- (behind right kick panel)
- (early production) s281
- (near breakout to c1019) s115
- (no connection)
- (roof ends in harness)
- C2212a
- C2212b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Central junction box (cjb) (below dash, left of steering column)
- Crown victoria
- Door ajar indicator
- Driver side rear door ajar switch (at rear of left rear door)
- Early
- Fuse 15a
- G109
- G109 (at front of right fender)
- G204
- G410 (in luggage compartment)
- Grand marquis
- Hot at all times
- Late
- Left rear park/stop/ turn lamp 1
- Left rear park/stop/ turn lamp 2
- Maj
- Min
- Passenger side front door ajar switch (at top rear of right front door)
- Passenger side rear door ajar switch (at rear of right rear door)
- Production
- Right front park/ turn lamp
- Right front parking lamp
- Right rear park/stop/ turn lamp 1
- Right rear park/stop/ turn lamp 2
- S107
- S114
- S158
- S204 (late production)
- S226
- S227 (late production)
- S238
- S259 (in main body wiring harness, near breakout to g200)
- S282 (early production)
- Taxi roof lamp
- Taxi roof lamp switch
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram (1 of 4) for Ford Crown Victoria S 2005
List of elements for Ground Distribution Wiring Diagram (1 of 4) for Ford Crown Victoria S 2005:
- (in dash panel to headlamp junction harness, near breakout to c1010)
- (in engine control sensor & fuel charge wiring harness, near breakout to c192) s157
- (right side of engine) g110
- A/c clutch field coil
- A/c clutch relay
- A/c compressor clutch diode
- Abs control module
- Accessory relay
- Air bag sliding contact (base of steering column)
- Air suspension compressor assembly
- Automatic a/c
- Battery
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Blower motor relay
- Brake fluid level switch
- C1048a
- C175b
- C217b
- C218a
- C218b
- C526b
- C602b
- C715b
- C820b
- Crown victoria
- Data link connector (dlc)
- Daytime running lamps (drl) module
- Diode
- Driver side front door ajar switch
- Driver side rear door ajar switch
- Engine cooling fan module
- Front blower motor resistor assembly
- Front blower motor speed controller
- Fuel pump relay
- G100 (at front of right fender)
- G101 (at right front of engine)
- G102 (at front of left fender)
- G103 (at front of left fender)
- G104 (at front of left fender)
- G105 (at front of left fender)
- G106 (at left rear of engine compartment)
- G107 (at left rear of engine compartment)
- G108 (at front of right fender)
- G109 (at front of right fender)
- Grand marquis
- Heated pvc
- Horn
- Horn switch
- Ignition coils relay
- Lead wiring harness, in breakout to c1046) s158
- Left front cornering lamp
- Left front engine compartment ends in harness
- Left front park/ turn lamp
- Left front parking lamp
- Left headlamp
- Low brand radio trunk ends in harness
- Manual a/c
- Mass air flow/ intake air temperature (maf/iat) sensor
- Nca
- Passenger side front door ajar switch
- Passenger side rear door ajar switch
- Pcm power relay
- Police power relay
- Powertrain control module (pcm)
- Pump motor)
- Right front cornering lamp
- Right front engine compartment ends in harness
- Right front park/ turn lamp
- Right front park/turn lamp
- Right front parking lamp
- Right headlamp
- S107 (in right turn lamps wiring harness, in breakout to c1019)
- S108 (in turn lamps wiring harness, in breakout to c1010)
- S114 (in dash panel to headlamp junction harness, near breakout to c1019)
- S118 (in dash panel to headlamp junction harness, left rear of engine compartment)
- S121 (in dash panel to headlamp junction harness, near breakout to battery junction box)
- S159 (in headlamp lead wiring harness, in breakout to c1047)
- S238 (in main body wiring harness, near breakout to variable assist power steering module)
- Shield
- Starter relay
- W/ air suspension compressor assembly
- W/ police
- W/o air suspension compressor assembly
- W/o police
- Washer fluid level switch
- Windshield washer pump motor
- Windshield wiper motor
Ground Distribution Wiring Diagram (2 of 4) for Ford Crown Victoria S 2005
List of elements for Ground Distribution Wiring Diagram (2 of 4) for Ford Crown Victoria S 2005:
- (alpine, sanyo)
- (analog) instrument cluster
- (base audio)
- (in steering wheel control switch jumper harness)
- (manual a/c) function selector switch assembly
- (w/ audio/climate control switch)
- (w/o audio/climate control switch)
- Adjustable pedal switch
- Air bag sliding contact (base of steering column)
- Alpine, sanyo
- Analog
- Audio/climate control switch
- Autolamp/ sunload sensor
- Automatic a/c
- Base vehicle
- Brake shift interlock
- C202b
- C203
- C205a
- C205b
- C2145a
- C2145c
- C218a
- C218b
- C220a
- C220c
- C2220a
- C2220b
- C228a
- C2330a
- C2330b
- C240
- C290a
- C294b
- C294d
- C310a
- C310b
- C501b
- Data link connector (dlc)
- Digital
- Driver door module
- Early production
- Electronic automatic temperature control (eatc) module
- Engine coolant temperature (ect) sensor
- Floor shifter
- Front cigar lighter
- Fuel tank unit
- Function selector switch assembly
- G201 (behind right kick panel)
- G202 (behind right kick panel)
- G203 (behind right kick panel)
- G204 (behind right kick panel)
- G205 (behind right kick panel)
- G207 (behind right kick panel)
- G209 (w/o power seats) (behind right kick panel)
- Instrument cluster
- Late production
- Left footwell courtesy lamp
- Lighting control module
- Main light switch
- Manual a/c
- Message center switch
- Multifunction switch
- Nca
- Occupant classification sensor module
- Passenger side door lock switch
- Passenger side in footwell ends in harness
- Passive anti-theft transceiver
- Power point
- Radio
- Rear window defrost switch
- Restraints control module
- Right exterior rear view mirror
- Right footwell courtesy lamp
- Roof ends in harness
- S201 (in main wiring harness, in breakout to adjustable pedal switch)
- S204
- S207 (in main wiring harness, near breakout to rear window defrost switch)
- S210 (in main wiring harness, near breakout to passenger air bag deactivation indicator)
- S212 (in cigar lighter wiring harness, near breakout to front cigar lighter)
- S217 (in main body wiring harness, near breakout to g200)
- S281
- S294
- S600 (in main body wiring harness, near breakout to passenger side front power window motor)
- Steering wheel/ speed control switch
- Taxi roof lamp switch
- Temperature blend door actuator
- Traction control switch
- W/ audio/climate control switch
- W/ center console
- W/o audio/climate control switch
- W/o center console
- Warning lamps module
- Windshield wiper motor
Ground Distribution Wiring Diagram (3 of 4) for Ford Crown Victoria S 2005
List of elements for Ground Distribution Wiring Diagram (3 of 4) for Ford Crown Victoria S 2005:
- (in emergency jumper wiring harness, near breakout to c291) s299
- (in glove box) police glove box relay/ fuse center
- (in left rear of luggage compartment) emergency flasher relay block
- (in luggage compartment wiring harness, near breakout to c405) s403
- Air suspension module
- Brake pedal position switch
- C2131b
- C2231b
- C3257a
- C402b
- C4170b
- C501b
- C504b
- C9013b
- C930
- Cd changer
- Crown police
- Driver door module
- Driver seat lumber compressor motor
- Driver side door lock switch
- Driver side front heated seat module
- Driver side front seat adjust switch
- Driver side seat heater switch
- Emergency flasher relay 1
- Emergency flasher relay 2
- Exterior rear view mirror switch
- Fuel pump driver module
- G206 (at right kick panel)
- G210 (behind right kick panel)
- G212 (at left kick panel)
- G213 (at left kick panel)
- G400 (at right rear of luggage compartment)
- G402 (behind right rear seat)
- G403 (behind right rear seat)
- G404 (behind right rear seat)
- G405 (at rear center of luggage compartment)
- G406 (at rear center of luggage compartment)
- G407 (behind left rear seat)
- Glove box ends in harness
- Key pad switch assembly
- Left exterior rear view mirror
- Left rear air spring solenoid valve
- Left rear police flasher lamp
- Left reversing lamp
- License lamps
- Luggage compartment lid release solenoid
- Luggage compartment lid release switch 1
- Master window adjust switch
- Nca
- Not used
- Overhead console
- Parking brake switch
- Police
- R2.a1
- R2.a4
- R2.a6
- Rear police auxiliary junction box
- Rear window defrost grid
- Right rear air spring solenoid valve
- Right rear police flasher lamp
- Right reversing lamp
- S267 (in main wiring harness, near breakout to g212)
- S285
- S315 (in power seats harness, near breakout to c311)
- S405 (in main body wiring harness, near breakout to fuel pump driver module)
- S420 (in rear license plate lamp wiring harness, near breakout to c405)
- S500 (in main body wiring harness, near breakout to exterior rearview mirror switch)
- Strobe/ light bar control switches
- Subwoofer amplifier
- Trunk ends in harness
- Variable assist power steering (vaps) module
- W/ air suspension
- W/ heated seats
- W/ keyless entry
- W/ overhead console
- W/ roof opening panel
- W/o air suspension
- W/o keyless entry
- W/o roof opening panel
Ground Distribution Wiring Diagram (4 of 4) for Ford Crown Victoria S 2005
List of elements for Ground Distribution Wiring Diagram (4 of 4) for Ford Crown Victoria S 2005:
- (in luggage compartment) g411
- (in luggage compartment) police trunk relay/ fuse center
- C4231a
- C4231b
- C4231c
- Electro- chromatic inside mirror unit
- Ends in harness trunk
- G200 (behind right kick panel)
- G401 (at right rear of luggage compartment)
- G410 (in luggage compartment)
- High mounted stoplamp
- In rear lamp wiring harness, in breakout to c411 (right))
- Interior spot lamp
- Left rear park/stop turn lamp 2
- Left rear park/stop/ turn lamp 1
- Left vanity mirror lamp
- Map reading lamps
- Nca
- Others
- Overhead console
- Passenger seat lumbar compressor motor
- Passenger side door lock switch
- Passenger side front heated seat module
- Passenger side front seat adjust switch
- Passenger side seat heater switch
- Police
- Police/ taxi/ lwb
- R4.b1
- R4.b3
- R4.b4
- Rear deck led flasher
- Rear interior/ map lamps assembly
- Right exterior rear view mirror
- Right rear park/stop turn lamp 2
- Right rear park/stop/ turn lamp 1
- Right vanity mirror lamp
- Roof opening panel unit
- S320 (in power seats harness, near breakout to occupant classification sensor module)
- S400 (in rear lamp wiring harness, in breakout to c410)
- S401
- S402 (in main body wiring harness, near breakout to high mounted stop lamp)
- S465 (in emergency jumper wiring harness, near breakout for c422)
- S476 (in power distribution wiring harness, in breakout to police trunk relay/fuse center)
- S600 (in main body wiring harness, near breakout to passenger side front power window motor)
- S902 (in interior lamps wiring harness, in breakout to c913)
- Siren amplifier
- Strobe control module
- Trunk air circulation fan motor
- W/ heated seats
- W/ police
- W/ spot lamp
- W/o police
HEADLIGHTS
Headlamps Wiring Diagram, with DRL for Ford Crown Victoria S 2005
List of elements for Headlamps Wiring Diagram, with DRL for Ford Crown Victoria S 2005:
- (analog)
- (at front of right fender) g109
- (behind center of dash) lighting control module
- (digital)
- (or 964)
- Analog
- Auto
- Auto lamp delay
- Auto lamp enable (or ign run or acc)
- Auto lamp on/off
- Auto lamp/ sunload sensor (on upper left side of dash)
- Bat pwr
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Breakout to c260) s278
- C1365a
- C202c
- C205a
- C2145a
- C2145b
- C2145c
- C220a
- C220c
- C2220b
- Central junction box (cjb) (below dash, left of steering column)
- Crown police
- Daytime running lamps (drl) module (right rear of engine compt)
- Digital
- Except police
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G102 (at front of left fender)
- G109 (at front of right fender)
- G201 (behind right kick panel)
- G201 (digital) (behind right kick panel)
- G203 (analog)
- G203 (behind right kick panel)
- Ground
- Head
- Headlamp input
- Hi beam in
- Hi beam indicator
- Hot at all times
- Hot in acc or run
- Hot in run
- Hot in start or run
- Ign (run)
- Ign start or run
- Instrument cluster
- Left headlamp
- Lo beam in
- Main light switch
- Multi- function switch
- Nca
- Off
- Park
- Park lamp input
- Pass
- Pnk
- Police
- Power (battery)
- Power feed
- Right headlamp
- S114
- S114 (except crown victoria)
- S138 (in dash panel to headlamp junction harness, near breakout to pcm)
- S159 (crown victoria)
- S200 (in main body wiring harness, near breakout to c264)
- S201
- S202
- S207
- S209 (manual a/c)
- S210
- S276
- Wig-wag jumper 1 (on right front side of engine compt)
- Wig-wag module (right side of engine compt)
Headlamps Wiring Diagram, without DRL for Ford Crown Victoria S 2005
List of elements for Headlamps Wiring Diagram, without DRL for Ford Crown Victoria S 2005:
- (analog)
- (behind center of dash) lighting control module
- (digital)
- (or 964)
- (or ign run or acc)
- Analog
- Auto
- Auto lamp delay
- Auto lamp enable
- Auto lamp on/off
- Auto lamp/ sunload sensor (on upper left side of dash)
- C1365a
- C202c
- C205a
- C2145a
- C2145b
- C2145c
- C220a
- C220c
- C2220b
- Central junction box (cjb) (below dash, left of steering column)
- Digital
- Except police
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G102 (at front of left fender)
- G109 (at front of right fender)
- G201 (behind right kick panel)
- G201 (digital) (behind right kick panel)
- G203 (analog)
- G203 (behind right kick panel)
- Head
- Headlamp input
- Hi beam indicator
- Hot at all times
- Hot in run or acc
- Hot in run or start
- Ign start or run
- Instrument cluster
- Left headlamp
- Main light switch
- Multi- function switch
- Nca
- Off
- Park
- Park lamp input
- Pass
- Pnk
- Police
- Police crown
- Power (battery)
- Power feed
- Right headlamp
- S112 (except crown victoria)
- S114 (except crown victoria)
- S138 (in dash panel to headlamp junction harness, near breakout to pcm)
- S158 (crown victoria)
- S159 (crown victoria)
- S201
- S202
- S207
- S210
- S276
- S278 (in main wiring harness, near breakout to lighting control module)
- Wig-wag jumper 1 (on right front side of engine compt)
- Wig-wag module (right side of engine compt)
Lighting Control Module Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Lighting Control Module Wiring Diagram for Ford Crown Victoria S 2005:
- (behind right kick panel) g203
- Air bag tone drv sig
- All doors lock in
- Anti-lock brakes system
- Auto lamp/ sunload sensor (on upper left side of dash)
- Autolamps on/off
- Autolmp enab or pwr
- Brake ctrl
- C2145a
- C2145b
- C2145c
- C220a
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Courtesy lamps out
- Cruise control system
- Data link connector
- Decklid ajar sw
- Defogger system
- Demand lighting out
- Dome lamp sw
- Door ajar out
- Door ajar sig
- Door handle sws
- Door lock actuator
- Door locks system
- Driver door ajar sw
- Electronic suspension system
- Engine controls system
- Exterior lights system
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G201 (behind right kick panel)
- Ground
- Hazard warn indic
- Headlamp off
- Headlamp sw
- Headlamps circuit
- Horn relay out
- Horns system
- Hot at all times
- Hot in run or acc
- Hot in start or run
- Ind sig
- Instrument cluster
- Interior lights system
- Key-in-ignition sw
- Lighting control module (behind center of dash)
- Low beams out
- Panel dim down sw
- Panic alarm in
- Parklamp sw
- Pass door ajar sw
- Police
- Pos sig
- Power (battery)
- Power (ignition)
- Power distribution system
- Pulse width dim out
- Pwr
- Rear defog relay
- Rear defog sw
- S201
- S202 (police)
- S210
- S227 (taxi)
- S276
- Seat belt indic out
- Shift interlock system
- Sw power
- Sw pwr
- Tone driver
- Trunk, tailgate, fuel doors system
- Variable volt dimming
- Vpwr
- Vss
- Warning system
- Wiper/washer system
HORN
Horn Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Horn Wiring Diagram for Ford Crown Victoria S 2005:
- (at front of right fender)
- Air bag sliding contact (at base of steering column)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145b
- C217a
- C217b
- C218a
- C218b
- Fuse 20a
- G108
- G109 (at front of right fender)
- Horn (near front center of engine compartment)
- Horn relay
- Horn switch (near steering wheel)
- Hot at all times
- Lighting control module (behind center of dash)
- Nca
Horn Wiring Diagram, Crown Police for Ford Crown Victoria S 2005
List of elements for Horn Wiring Diagram, Crown Police for Ford Crown Victoria S 2005:
- Air bag sliding contact (at base of steering column)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145b
- C217a
- C217b
- C218a
- C218b
- Fuse 20a
- Fuse b7 20a
- Fuse c9 5a
- G108 (at front of right fender)
- G109 (at front of right fender)
- G411 (in luggage compartment)
- Horn (near front center of engine compartment)
- Horn relay
- Horn switch (near steering wheel)
- Hot at all times
- Lighting control module (behind center of dash)
- Nca
- Police light bar relay/ fuse center (in front of luggage compt)
- Police trunk relay/ fuse center (in luggage compartment)
- Police trunk relay/fuse center (in luggage compt)
- Relay 3
- S205 (in main wiring harness, near breakout to passive anti-theft transceiver)
- S476
- Siren amplifier (in luggage compartment)
- W/ siren
- W/o siren
INSTRUMENT CLUSTER
Analog Cluster Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Analog Cluster Wiring Diagram for Ford Crown Victoria S 2005:
- "air bag" indicator
- "traction control" ind
- (6 bulbs)
- (at front of left fender) g103
- (in main wiring harness, in breakout to instrument cluster) s202
- (taxi) s227
- Abs control module (at left front of engine compt)
- Abs indicator
- Air bag indicator
- Air suspension module (behind right side of dash, above glove box)
- Anti-slosh module
- Brake fluid level switch (on brake fluid reservoir)
- Brake ind ctrl
- C175b
- C175t
- C2131a
- C2145c
- C2220a
- C2220b
- C310a
- Cap indicator
- Central junction box (cjb) (below dash, left of steering column)
- Charge indicator
- Check fuel
- Check gauge indicator
- Check suspension/ fire suppression indicator
- Electronic throttle control ind
- Engine coolant temperature (ect) sensor (top right front of engine, near fuel injector 1)
- Engine coolant temperature gauge
- Exterior lights system
- Fuel gauge
- Fuel tank unit (in fuel tank)
- Fuse 10a
- Fuse 15a
- G102 (at front of left fender)
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- G212 (at left kick panel)
- Gauge
- Gnd
- Headlights system
- Hi beam indicator
- Hot at all times
- Hot in run
- Hot in start or run
- Illumination lamps
- Indicator control
- Indicator output
- Instrument cluster
- Interior lights system
- Left turn indicator
- Lighting control module (behind center of dash)
- Low
- Low brake fluid level/ park brake ind
- Low fuel indicator
- Low oil pressure
- Malfunction indicator lamp (mil)
- Microprocessor
- Normal
- Oil pressure switch (lower left side of engine, above oil filter)
- Overdrive cancel ind
- Parking brake switch (behind left side of dash, on top of parking brake assembly)
- Powertrain control module (pcm) (left rear of engine compt)
- Restraints control module (below center of dash)
- Right turn indicator
- S104 (near breakout to g102)
- S112
- S207
- S210
- S247 (near breakout to c410)
- S267
- S276
- Safety belt indicator
- Speedometer
- Voltmeter
Electronic Cluster Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005
List of elements for Electronic Cluster Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005:
- (at front of left fender) g102
- (behind center of dash) electronic automatic temperature control (eatc) module
- (behind right side of dash, above glove box) air suspension module
- (in fuel tank) fuel tank unit
- (left rear of engine compt) powertrain control module (pcm)
- (on top right front of engine, near fuel injector 1) engine coolant temperature (ect) sensor
- Air susp ind
- C175b
- C175t
- C2131a
- C220a
- C220b
- C220c
- C228b
- Central junction box (cjb) (below dash, left of steering column)
- Charge ind
- Door ajar ind
- E/m
- Ect ind
- Eng/met
- Etcil
- Exterior lights system
- Fail-safe cooling ind
- Fuel cap ind
- Fuel level data
- Fuel level ind
- Fuse 10a
- Fuse 15a
- G201 (behind right kick panel)
- Gnd
- Headlights system
- Hi beam ind
- Hot at all times
- Hot in run
- Illum
- Illumination
- Ind
- Instrument cluster
- Interior lights system
- Left turn ind
- Low washer fluid ind
- Message center switch
- Microprocessor
- Mil ind
- Oil pres ind
- Oil pressure switch (lower left side of engine, above oil filter)
- Out
- Red
- Reset
- Right turn ind
- S112
- S202 (in main wiring harness, in breakout to instrument cluster)
- S210
- S227
- S247 (in main wiring harness, near breakout to c410)
- Safety belt indicator
- Select
- Speed control ind
- Speedometer
- Starting/charging system
- Taxi
- Tcil ind
- Tone driver
- Traction ctrl ind
- Trunk ajar ind
- Vbatt
- Vpwr
- Vref
- Washer fluid level switch (in washer fluid reservoir)
Electronic Cluster Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005
List of elements for Electronic Cluster Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005:
- (at front of left fender) g102
- (early production) s282
- (in dash panel to headlamp junction harness, near breakout to g102) s104
- Abs control module (at left front of engine compt)
- Abs ind
- Air bag ind
- Ajar lamp output
- Anti-lock brakes system
- Brake fluid level switch (on brake fluid reservoir)
- C2145a
- C2145b
- C2145c
- C2212a
- C2212b
- C501a
- C526a
- C602a
- C602b
- C715a
- C715b
- C820a
- Central junction box (cjb) (below dash, left of steering column)
- Decklid jar
- Door ajar indicator (taxi)
- Door ajar input
- Driver door module (bottom front of left front door)
- Driver side front door ajar switch (at top rear of left front door) c526b
- Driver side rear door ajar switch (at rear of left rear door)
- Driver's ajar switch
- Early production
- Fuse 10a
- G109 (at front of right fender)
- G203 (behind right kick panel)
- G212 (at left kick panel)
- G406 (at rear center of luggage compt)
- Hazard ind
- Hot in start or run
- Late production
- Lighting control module (behind center of dash)
- Low brake fluid level/ park brake ind
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Parking brake switch (behind left side of dash, on top of parking brake assembly)
- Pass ajar switch
- Passenger side front door ajar switch (at top rear of right front door)
- Passenger side rear door ajar switch (at rear of right rear door) c820b
- S112
- S207
- S230 (in main body wiring harness, near breakout to temperature blend door actuator)
- S240 (in main wiring harness, in breakout to instrument cluster)
- S267
- S276
- S277 (near breakout to lighting control module)
- S403
- Safety belt ind out
- Seatbelt switch
- Tone request
- Trunk, tailgate, fuel doors system
- Warning lamps module (behind left side of dash)
Overhead Console Wiring Diagram, with Roof Opening Panel for Ford Crown Victoria S 2005
List of elements for Overhead Console Wiring Diagram, with Roof Opening Panel for Ford Crown Victoria S 2005:
- Battery junction box (bjb) (in right front engine compartment, behind battery)
- C9013a
- C9013b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Engine controls system
- Fuse 20a
- Fuse 7.5a
- G210 (behind right kick panel)
- Gnd
- Hot at all times
- Hot in run
- Interior lights system
- Overhead console
- Power tops system
- Pwr
- S904
- S905
- Scp+
- Scp-
- Tan/red
- Vbatt
- Vpwr
- Vss
Overhead Console Wiring Diagram, without Roof Opening Panel for Ford Crown Victoria S 2005
List of elements for Overhead Console Wiring Diagram, without Roof Opening Panel for Ford Crown Victoria S 2005:
- (at right rear of luggage compt)
- (behind right kick panel)
- (near breakout to rear window defrost switch)
- C2145c
- Central junction box (cjb) (below dash, left of steering column)
- Engine controls system
- Fuse 7.5a
- G210
- G401
- Gnd
- Hot in run or acc
- Interior lights system
- Lighting control module (behind center of dash)
- Overhead console
- S229
- S287
- S902
- Vpwr
- Vss
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Courtesy Lamps Wiring Diagram for Ford Crown Victoria S 2005:
- (at rear center of luggage compartment) g406
- (at rear of left front door) left front exterior door handle switch
- (at rear of left rear door) driver side rear door ajar switch
- (at rear of right front door) right front exterior door handle switch
- (at rear of right rear door) passenger side rear door ajar switch
- (at right rear of luggage compartment) g401
- (at top rear of left front door) driver side front door ajar switch
- (at top rear of right front door) passenger side front door ajar switch
- (in interior lamps wiring harness, in breakout to c913)
- (in interior lamps wiring harness, near breakout to right vanity mirror lamp)
- (in main body wiring harness, near breakout to g200)
- (in main body wiring harness, near breakout to temperature blend door actuator) s223
- (in main wiring harness, in breakout to instrument cluster) s240
- (in main wiring harness, near breakout to eatc) s236
- (in main wiring harness, near breakout to passenger air bag deactivation indicator)
- Base vehicle/ police
- C205b
- C2145a
- C2145b
- C2145c
- C220b
- C2212a
- C526a
- C526b
- C9013a
- C9013b
- Central junction box (cjb) (below dash, left of steering column)
- Digital cluster
- Dimmer
- Door ajar
- Door ajar indicator
- Early production
- Emergency flasher relay block (in left rear of luggage compt)
- Except base vehicle/police
- Exterior lights system
- Fuse 15a
- G203 (behind right kick panel)
- G204 (behind right kick panel)
- Glove box lamp
- Handle sw
- Hot at all times
- Instrument cluster
- Interior
- Interior spot lamp (if equipped)
- Left footwell courtesy lamp
- Left vanity mirror lamp
- Lighting control module (behind center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Main light switch
- Map reading lamps
- Nca
- Overhead console (w/ roof opening panel)
- Overhead console (w/o roof opening panel)
- Police
- Power distribution system
- Pwr
- Rear flasher relay
- Rear interior/ map lamps assembly
- Right footwell courtesy lamp
- Right vanity mirror lamp
- S204
- S222
- S227 (taxi)
- S238
- S259
- S290
- S402
- S403
- S900
- S902
- S903 (w/ roof opening panel)
- Trunk ajar
- Vbatt
- Vpwr
- Vref
- W/ roof opening panel
- W/o remote keyless entry
- W/o roof opening panel
Instrument Illumination Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Instrument Illumination Wiring Diagram for Ford Crown Victoria S 2005:
- (at base of steering column) air bag sliding contact
- (behind right kick panel) g203
- (in main wiring harness, near breakout to eatc s233
- (in steering wheel control switch jumper harness) s293
- Adjustable pedal switch
- Alpine, sanyo
- Audio/ climate control switch
- Auto
- Automatic a/c
- Base audio
- C205a
- C205b
- C2145a
- C2145b
- C2145c
- C218a
- C218b
- C220a
- C220c
- C2220b
- C228a
- C228b
- C2330a
- C2330b
- C240
- C290a
- C294d
- C501a
- C9013a
- Central junction box (cjb) (below dash, left of steering column)
- Dimmer
- Driver door module (bottom front of left front door)
- Driver side door lock switch
- Electronic automatic temperature control (eatc) module (behind center of dash)
- Except taxi
- Floor shifter
- Function selector switch assembly
- Fuse 10a
- Fuse 15a
- Fuse 5a
- Fuse 7.5a
- G200 (w/ power seat) (behind right kick panel)
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- G204 (behind right kick panel)
- G209 (w/o power seat) (behind right kick panel)
- G212 (at left kick panel)
- Head
- Hot at all times
- Hot in run or acc
- Hot in start
- Illum
- Illumination
- Instrument cluster (analog)
- Instrument cluster (digital)
- Interior
- Key pad switch assembly
- Lighting control module (behind center of dash)
- Main light switch
- Manual a/c
- Message center switch (digital)
- Off
- On/off sig
- Overhead console
- Park
- Passenger side door lock switch
- Power distribution system
- Pwr
- Radio
- Rear window defrost switch
- S201
- S204
- S207
- S210
- S229
- S287 (in main wiring harness, near breakout to rear window defrost switch)
- S294
- S500
- S501
- S600
- Steering wheel/ speed control switch
- Traction control switch
- Vbatt
- Vref
- W/ steering wheel audio/climate control switch
- W/o steering wheel audio/climate control switch
POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 5) for Ford Crown Victoria S 2005
List of elements for Power Distribution Wiring Diagram (1 of 5) for Ford Crown Victoria S 2005:
- (in main wiring harness, near breakout to c248) s242
- (in right front of engine compartment, behind battery) battery junction box (bjb)
- Abs control module
- Acc
- Automatic a/c
- Battery
- Brake shift interlock
- C102a
- C102b
- C1048a
- C175b
- C197a
- C202a
- C2145a
- C294a
- C501a
- C501b
- C501c
- Central junction box (cjb) (below dash, left of steering column)
- Crown police
- Daytime running lamps (drl) module
- Digital transmission range (dtr) sensor
- Driver door module
- Driver side front heated seat module
- Driver side front seat adjust switch
- Driver side lumbar adjust switch
- Engine cooling fan module
- Except police
- Function selector switch assembly
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 25a
- Fuse 30a
- Fuse 40a
- Fuse 50a
- Fuse 5a
- Fusible link b
- Generator
- Ignition switch
- Lighting control module
- Lock
- Low band radio ends in trunk harness
- Luggage compart- ment lid release switch 2
- Luggage compartment lid release switch 1
- Manual a/c
- Multifunction switch
- Nca
- Off
- Passenger side front heated seat module
- Passenger side front seat adjust switch
- Passenger side in footwell ends in harness
- Passenger side lumbar adjust switch
- Police
- Powertrain control module (pcm)
- Red
- Run
- S137
- S162
- S209
- Start
- Starter motor
- Temperature blend door actuator
- To central junction box fuse 15 (diagram 5 of 5)
- To central junction box fuse 2 (diagram 2 of 5)
- To central junction box fuse 20 (diagram 2 of 5)
- To fuse 8 (diagram 2 of 5)
- To g200)
- W/ heated seats
- W/ police
- W/o police
- Windshield wiper motor
Power Distribution Wiring Diagram (2 of 5) for Ford Crown Victoria S 2005
List of elements for Power Distribution Wiring Diagram (2 of 5) for Ford Crown Victoria S 2005:
- (in dash panel to headlamp junction harness, near breakout to pcm) s101
- (in right front of engine compartment, behind battery) battery junction box (bjb)
- Abs control module
- Air suspension module
- Analog
- Automatic a/c
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Blower motor relay
- C2131b
- C2145a
- C220a
- C220c
- C2220a
- C2220b
- C2231b
- C228a
- C294a
- C310a
- C310b
- C501c
- Central junction box (cjb) (below dash, left of steering column)
- Digital
- Digital transmission range (dtr) sensor
- Driver door module
- Driver side door lock switch
- Electronic automatic temperature control (eatc) module
- Floor shifter
- From central junction box (cjb) fuse 24 (diagram 2 of 5)
- From fuse 111 (diagram 1 of 5)
- From ignition switch (diagram 1 of 5)
- Fuel pump relay
- Function selector switch assembly
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 30a
- Fuse 40a
- Heated pvc
- Ignition coils relay
- Instrument cluster
- Lighting control module
- Manual a/c
- Occupant classification sensor module
- Overdrive cancel switch
- Passenger airbag deactivation (pad) indicator
- Passenger side door lock switch
- Passive anti-theft transceiver
- Pcm power diode
- Pcm power relay
- Rear window defrost relay
- Restraints control module
- S164
- S208 (in main body wiring harness, near breakout to instrument cluster)
- S213 (in main body wiring harness, near breakout to c237)
- S276 (in main wiring harness, near breakout to instrument cluster)
- Starter relay
- To battery junction box (bjb) fuse 5 (diagram 3 of 5)
- To battery junction box (bjb) ignition coils relay (diagram 2 of 5)
- Variable assist power steering (vaps) module
- W/ air suspension
- W/ center console
- W/ keyless entry
- W/o air suspension
- W/o center console
- W/o keyless entry
- Warning lamps module
Power Distribution Wiring Diagram (3 of 5) for Ford Crown Victoria S 2005
List of elements for Power Distribution Wiring Diagram (3 of 5) for Ford Crown Victoria S 2005:
- (diagram 3 of 5)
- (in main wiring harness, near breakout to g200) s221
- (in main wiring harness, near breakout to passenger air bag module) s211
- (in power distribution wiring harness, in breakout to police light bar relay/fuse red center) s462
- (not used)
- 2131b
- A/c clutch relay
- Air suspension module
- Alpine, sanyo
- Base audio
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- Blower motor relay
- Brake pedal position switch
- C2231b
- C240
- C290a
- Cd changer
- Central junction box (cjb) (below dash, left of steering column)
- Compartment wiring harness, near breakout to c405)
- Crown police
- Daytime running lamps (drl) module
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (in left rear of luggage compt)
- Ends in console harness
- Ends in center console harness
- From battery junction box (bjb) fuse 16 c
- From battery junction box b (bjb) fuse 105 (diagram 2 of 5)
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 25a
- Fuse 40a
- Fuse 50a
- Fuse b1 15a
- Fuse b2 15a
- Fuse b3 15a
- Horn relay
- Passenger side in footwell ends in harness
- Police
- Police light bar relay/fuse center (in front of luggage compartment)
- Police option fuse holder (in glove box)
- Power point
- R4.c1
- R4.c2
- R4.c3
- R4.c4
- R4.c5
- R4.c6
- R4.c7
- R4.c8
- Radio
- Rear flasher relay
- Rear police auxiliary junction box
- Red
- S466
- S469 (in power distribution wiring harness, in breakout to police light bar relay/fuse center)
- Subwoofer amplifier
- To battery junction box (bjb) fuse 103 (diagram 4 of 5)
- To battery junction box (bjb) fuse 113 (diagram 3 of 5)
- To g212)
- Variable assist power steering (vaps) module
- W/ air suspension
- W/ police
- W/o air suspension
- W/o police
Power Distribution Wiring Diagram (4 of 5) for Ford Crown Victoria S 2005
List of elements for Power Distribution Wiring Diagram (4 of 5) for Ford Crown Victoria S 2005:
- (in emergency jumper wiring harness, near breakout to c298) s291
- (in interior lamps wiring harness, in breakout to c913) s905
- (in main body wiring harness, near breakout to g212) s254
- (in main body wiring harness, near breakout to instrument cluster) s206
- (in main wiring harness, near breakout to c248) s237
- (not used)
- 9013b
- Adjustable pedal switch
- All others
- Analog
- Autolamp/ sunload sensor
- Automatic a/c
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Brake pedal position switch
- Brake shift interlock
- C202a
- C202c
- C2145c
- C220a
- C2212b
- C2220a
- C228a
- Central junction box (cjb) (below dash, left of steering column)
- Data link connector (dlc)
- Deactivator switch
- Digital
- Door ajar indicator
- Driver side door lock switch
- Electronic automatic temperature control (eatc) module
- Ends in harness
- Exterior rear view mirror switch
- From battery junction box d (bjb) fuse 117 (diagram 3 of 5)
- Front cigar lighter
- Fuse 10a
- Fuse 15a
- Fuse 15a (w/o police) 20a (w/ police)
- Fuse 20a
- Fuse 40a
- Fuse 50a
- Fuse a1 10a
- Fuse a2 5a
- Fuse a3 5a
- Instrument cluster
- Late production
- Left side spot lamp
- Lighting control module
- Manual a/c
- Multifunction switch
- Overhead console
- Passenger side door lock switch
- Pnk
- Police glove box relay/fuse center (in glove box)
- Police/ commercial
- R2.a1
- R2.a2
- R2.a4
- Radio
- Right side spot lamp
- Roof opening panel unit
- S227 (in main wiring harness, near breakout to c260)
- S282
- S284
- S286
- Tan
- Taxi roof lamp switch
- To battery junction box (bjb) fuse 118 (diagram 5 of 5)
- W/ keyless entry
- W/ pats
- W/ police
- W/ taxi
- W/o pats
- W/o taxi
Power Distribution Wiring Diagram (5 of 5) for Ford Crown Victoria S 2005
List of elements for Power Distribution Wiring Diagram (5 of 5) for Ford Crown Victoria S 2005:
- (in dash panel to headlamp junction harness, near breakout to battery junction box) s121
- (in emergency jumper wiring harness, near breakout for c422) s470
- (in main body wiring harness, near breakout to exterior rearview mirror switch) (w/ police) s502
- (in main wiring harness, in breakout to instrument cluster) s202
- (in power distribution wiring harness, at breakout for police luggage compartment
- Accessory relay
- Air suspension compressor relay
- Alpine, sanyo
- Base audio
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- C2145a
- C2145b
- C240
- C290a
- C504b
- C9013b
- Central junction box (cjb) (below dash, left of steering column)
- Crown police
- Driver side door lock switch
- Driver side seat heater switch
- Electro- chromatic inside mirror unit
- From battery junction box e (bjb) fuse 116 (diagram 4 of 5)
- From ignition switch (diagram 1 of 5)
- Fuse 10a
- Fuse 20a
- Fuse 30a (w/o police) 40a (w/ police)
- Fuse 50a
- Fuse 7.5a
- Fuse b1 5a
- Fuse b2 10a
- Fuse b3 5a
- Fuse b7 20a
- G109 (at front of right fender)
- Harness, near breakout to c248) s229
- Lighting control module
- Luggage compartment lid release switch 1
- Luggage compartment lid release switch 2
- Master window adjust switch
- Nca
- Overhead console
- Passenger side door lock switch
- Passenger side seat heater switch
- Police
- Police power relay
- Police trunk relay/fuse center (in luggage compartment)
- Police trunk relay/fuse center (in luggage compt)
- R4.b1
- R4.b2
- R4.b3
- R4.b4
- R4.b5
- Radio
- Rear police auxiliary junction box
- Relay/fuse center)
- Roof opening panel unit
- S474
- S478
- S904 (near breakout to electrochromatic inside mirror unit)
- To headlamp junction harness, near breakout to battery junction box) s120
- Trunk ends in harness
- W/ police
- W/ roof opening panel
- W/o police
- W/o roof opening panel
- Windshield wiper motor
POWER DOOR LOCKS
Power Door Locks Wiring Diagram, with Keyless Entry for Ford Crown Victoria S 2005
List of elements for Power Door Locks Wiring Diagram, with Keyless Entry for Ford Crown Victoria S 2005:
- (behind right kick panel) g201
- (in main body wiring harness, in breakout to driver's door module)
- (in main body wiring harness, near breakout to c248) s229
- (in main body wiring harness, near breakout to g212)
- (in main wiring harness, near breakout to lighting control module)
- (near breakout to driver's door module) s506
- 1/2
- 3/4
- 5/6
- 7/8
- 9/0
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145b
- C2145c
- C220a
- C501a
- C501b
- C501c
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Data link connector (dlc) (behind left side of dash)
- Digital
- Door ajar
- Door ajar ind
- Door lock
- Driver door module (bottom front of left front door)
- Driver side door lock switch
- Fuse 10a
- Fuse 20a
- Fuse 5a
- Fuse 7.5a
- G200 (w/ power seat) (behind right kick panel)
- G209 (w/o power seat) (behind right kick panel)
- G212 (at left kick panel)
- G406 (at rear center of luggage compt)
- Gnd
- Hndl sw sig rtn c2145a
- Hot at all times
- Hot in run
- Hot in run or acc
- Hot in start
- Illum
- Illumination
- Instrument cluster
- Iso
- Key pad illum
- Key pad sw a
- Key pad sw b
- Key pad sw c
- Key pad switch assembly
- Left front door lock actuator (at rear of left front door)
- Left rear door lock actuator (at rear of left rear door)
- Lighting control module (behind center of dash)
- Lock
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Luggage compt lid release switch 1
- Passenger side door lock actuator (at rear of right front door)
- Passenger side door lock switch
- Pwr
- Right rear door lock actuator (at rear of right rear door)
- S217
- S254
- S260 (in main body wiring harness, near breakout to g212)
- S261 (near breakout to g212)
- S262
- S263
- S271 (in main wiring harness, in breakout to data link connector)
- S277
- S403
- S500
- S503
- S510 (near breakout to exterior rearview mirror switch)
- S600
- Sig rtn
- Trunk lid
- Unlock
- Vbatt
- Vpwr
- Vref dr handle
- Vref out
Power Door Locks Wiring Diagram, without Keyless Entry for Ford Crown Victoria S 2005
List of elements for Power Door Locks Wiring Diagram, without Keyless Entry for Ford Crown Victoria S 2005:
- (in main body wiring harness, near breakout to passenger side front power window motor)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Central junction box (cjb) (below dash, left of steering column)
- Driver side door lock switch
- Fuse 20a
- Fuse 7.5a
- G200 (w/ power seat) (behind right kick panel)
- G209 (w/o power seat) (behind right kick panel)
- G212 (at left kick panel)
- Hot at all times
- Hot in run or acc
- Illumination
- Left front door lock actuator (at rear of left front door)
- Left rear door lock actuator (at rear of left rear door)
- Lock
- Passenger side door lock actuator (at rear of right front door)
- Passenger side door lock switch
- Right rear door lock actuator (at rear of right rear door)
- S229
- S232
- S501
- S600
- S601
- Unlock
POWER MIRRORS
Electronic Day/Night Mirror Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Electronic Day/Night Mirror Wiring Diagram for Ford Crown Victoria S 2005:
- (at right rear of luggage compartment) g401
- Central junction box (cjb) (below dash, left of steering column)
- Digital transmission range (dtr) sensor (on left side of transmission)
- Electrochromatic inside mirror unit
- Exterior lights system
- Fuse 10a
- Fuse 7.5a
- Ground
- Hot in run or acc
- Hot in run or start
- S215 (w/ auto-dimming interior mirror unit) (in main body wiring harness, near breakout to adjustable pedal motor)
- S902
- S904 (w/ roof opening panel)
- Vpwr
Power Mirrors Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Power Mirrors Wiring Diagram for Ford Crown Victoria S 2005:
- (w/o keyless entry) s501
- Central junction box (cjb) (below dash, left of steering column)
- Defogger system
- Down
- Exterior rear view mirror switch
- Fuse 10a
- G212 (at left kick panel)
- Hot at all times
- Left
- Left exterior rear view mirror
- Left mirror select
- Left/ right
- Left/ right m
- Nca
- Right
- Right exterior rear view mirror
- Right mirror select
- S254 (w/ keyless entry)
- S500 (w/ keyless entry)
- S503 (in main body wiring harness, in breakout to driver's door module)
- Up/ down m
POWER SEATS
Adjustable Pedal Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Adjustable Pedal Wiring Diagram for Ford Crown Victoria S 2005:
- Adjustable pedal motor (below left side of dash)
- Adjustable pedal switch
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Fwd
- G203 (behind right kick panel)
- G204 (behind right kick panel)
- Hot at all times
- Interior lights system
- Red
- Rwd
- S203 (w/ pats)
- S204
- S207
Driver Power Seat Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Driver Power Seat Wiring Diagram for Ford Crown Victoria S 2005:
- (at left kick panel) g213
- Backrest of seat
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Circuit breaker 20a
- Driver seat recliner motor (in driver's seat)
- Driver side front seat adjust switch
- Entire seat
- Front of seat
- Fwd
- Hot at all times
- Left power seat motor assembly (under left front seat)
- Nca
- Rear of seat
- Rwd
- S242
Heated Seats Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Heated Seats Wiring Diagram for Ford Crown Victoria S 2005:
- (at left kick panel) g212
- (behind right kick panel) g200
- (w/ keyless entry) s500
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Central junction box (cjb) (below dash, left of steering column)
- Driver side front heated seat module (under driver seat)
- Driver side seat heater switch
- Fuse 10a
- Fuse 20a
- Fuse 7.5a
- G200 (behind right kick panel)
- G212 (at left kick panel)
- High ind
- Hot at all times
- Hot in run
- Hot in run or acc
- Left front seat cushion heater (under left front seat)
- Low
- Low ind
- Nca
- Panel illum
- Passenger side front heated seat module (under passenger seat)
- Passenger side seat heater switch
- Red
- Right front seat cushion heater (under right front seat)
- S220
- S229
- S262
- S315
- S320
- S600
Lumbar Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Lumbar Wiring Diagram for Ford Crown Victoria S 2005:
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Circuit breaker 20a
- Driver seat lumbar compressor motor (under driver's seat)
- G200 (behind right kick panel)
- G212 (at left kick panel)
- Hot at all times
- Left front lumbar adjust switch
- Out
- Passenger seat lumbar compressor motor (under passenger's seat)
- Pnk
- Right front lumbar adjust switch
- S242
- S300 (in power seats harness, under driver seat)
- S310 (in power seats harness, near breakout to right front lumbar compressor motor) pnk
- S315 (w/ heated seats)
- S320 (w/ heated seats)
Passenger Power Seat Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Passenger Power Seat Wiring Diagram for Ford Crown Victoria S 2005:
- (behind right kick panel) g200
- Backrest of seat
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Circuit breaker 20a
- Entire seat
- Front of seat
- Fwd
- Hot at all times
- Nca
- Passenger seat recliner motor (under passenger's seat)
- Passenger side front seat adjust switch
- Rear of seat
- Right power seat motor assembly (under right front seat)
- Rwd
- S242
- S600
POWER TOP/SUNROOF
Power Top/Sunroof Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Power Top/Sunroof Wiring Diagram for Ford Crown Victoria S 2005:
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C9013b
- Central junction box (cjb) (below dash, left of steering column)
- Close/ tilt up
- Close/tilt up
- Except police/ commercial
- Fuse 20a
- Fuse 7.5a
- G401 (at right rear of luggage compt)
- Gnd
- Hot at all times
- Hot in run or acc
- Open/ tilt dn
- Open/tilt dn
- Overhead console
- Roof opening panel unit (in center of roof)
- S902
- S904
- S905
- Tan/red
- Vbatt
- Vpwr
POWER WINDOWS
Power Windows Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Power Windows Wiring Diagram for Ford Crown Victoria S 2005:
- (in main body wiring harness, near breakout to restraints control module)
- (police) s303
- Accessory relay
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- C504a
- C504b
- Driver
- Driver side front power window motor (in left front door)
- Fuse 20a
- G213 (at left kick panel)
- Hot at all times
- Left rear
- Left rear power window motor (in rear of left rear door)
- Left rear window adjust switch
- Lock
- Master window adjust switch
- One- touch down
- One-touch down relay
- Passenger
- Passenger side front power window motor (in right front door)
- Right rear
- Right rear power window motor (in front of right rear door)
- Right rear window adjust switch
- Right side front power window switch
- S264
- S502 (police) (near breakout to exterior rearview mirror switch)
- Vbatt
RADIO
Base Radio Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Base Radio Wiring Diagram for Ford Crown Victoria S 2005:
- (behind right kick panel) g203
- Antenna
- Battery junction box (bjb) (right front of engine compartment, behind battery)
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Fuse 3 (manual a/c) 10a fuse 29 (automatic a/c) 15a
- Fuse 5a
- Fused ignition
- G202 (behind right kick panel)
- Ground
- Hot at all times
- Hot in run or acc
- Hot in start w/ park or neutral
- Illum power
- Interior lights system
- L front spkr (+)
- L front spkr (-)
- L rear spkr (+)
- L rear spkr (-)
- Left front speaker
- Left rear speaker
- Nca
- Power
- R front spkr (+)
- R front spkr (-)
- R rear spkr (+)
- R rear spkr (-)
- Radio
- Right front speaker
- Right rear speaker
- S207
- Vpwr
Premium Sound Radio Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Premium Sound Radio Wiring Diagram for Ford Crown Victoria S 2005:
- (behind left rear seat) g407
- Air bag sliding contact (at base of steering column)
- Audio protocol a
- Audio protocol b
- Audio shield
- Audio system on
- Audio/climate control switch
- Battery junction box (bjb) (in right front of engine compartment, behind battery)
- C218a
- C218b
- C228b
- C290a
- C290b
- C290c
- Cd changer (alpine)
- Cd changer +
- Cd changer -
- Central junction box (cjb) (below dash, left of steering column)
- Electronic automatic temperature control (eatc) module (behind center of dash)
- Engine controls system
- Fan down
- Fan up
- Fuse 10a
- Fuse 15a
- Fuse 25a
- Fuse 5a
- G202 (behind right kick panel)
- G203 (behind right kick panel)
- G407 (behind left rear seat)
- Ground
- Hot at all times
- Hot in run or acc
- Hot in start w/ park or neutral
- Inst illum feed
- Interior lights system
- L cd changer +
- L cd changer -
- L front spkr +
- L front spkr -
- L rear spkr +
- L rear spkr -
- Left cd changer-
- Left front speaker
- Left rear speaker
- Mode
- Mute
- Nca
- Overload protected
- Phone
- Protocol a
- Protocol b
- R cd changer +
- R front spkr +
- R front spkr -
- R rear spkr +
- R rear spkr -
- Radio
- Rest
- Right cd changer-
- Right front speaker
- Right rear speaker
- Run/acc
- Rx sig
- S100
- S201
- S207
- S294 (in steering wheel control switch jumper harness)
- Shield
- Steering wheel sig
- Subwoofer amplifier (in luggage compartment, under rear package tray)
- Subwoofer mute
- Tan
- Temp down
- Temp up
- Tx sig
- Vbatt
- Vehicle speed sig
- Vpwr
SHIFT INTERLOCK
Shift Interlock Wiring Diagram, with Console for Ford Crown Victoria S 2005
List of elements for Shift Interlock Wiring Diagram, with Console for Ford Crown Victoria S 2005:
- (at left kick panel) g212
- (behind right kick panel) g204
- (in main body wiring harness, near breakout to variable assist power steering module)
- Brake pedal position switch (top of brake pedal support)
- Brake shift interlock (on steering column)
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Hot at all times
- Hot in run
- S204
- S225
- S237
- S267
- Solid state
Shift Interlock Wiring Diagram, without Console for Ford Crown Victoria S 2005
List of elements for Shift Interlock Wiring Diagram, without Console for Ford Crown Victoria S 2005:
- (at left kick panel) g212
- (in main body wiring harness, near breakout to variable assist power steering module)
- Bpp sw
- Brake pedal position switch (top of brake pedal support)
- Brake shift interlock (on steering column)
- Bsi
- C2145a
- C2145b
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Hot at all times
- Hot in start or run
- Lighting control module (behind center of dash)
- S225
- S237
- S267
- S276
- Vpwr
STARTING/CHARGING
Charging Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Charging Wiring Diagram for Ford Crown Victoria S 2005:
- Analog
- Battery
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175t
- C220a
- C220c
- C2220a
- Central junction box (cjb) (below dash, left of steering column)
- Charge ind
- Digital
- Fuse 10a
- Fuse 15a
- G100 (at front of right fender)
- G101 (at right front of engine)
- Generator
- Hot in run
- Instrument cluster
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- S137
- S162
- Starter motor
- Vp wr
Starting Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Starting Wiring Diagram for Ford Crown Victoria S 2005:
- (left rear of
- Acc
- Battery
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C175b
- Central junction box (cjb) (below dash, left of steering column)
- Charging circuit
- Control
- Digital transmission range (dtr) sensor (on left side of transmission)
- Engine compt)
- Except police package & 4.6l cng
- Fuse 10a
- Fuse 25a
- Fuse 30a
- G100 (at front of right fender)
- G101 (at right front of engine)
- G109 (at front of right fender)
- Hot at all times
- Ignition switch
- Lock
- Module (pcm)
- Off
- Police package & 4.6l cng
- Power distribution system
- Powertrain
- Red
- Run
- S121
- Start
- Starter motor
- Starter relay
SUPPLEMENTAL RESTRAINTS
Supplemental Restraints Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005
List of elements for Supplemental Restraints Wiring Diagram (1 of 2) for Ford Crown Victoria S 2005:
- (behind right kick panel)
- (in body main harness, near breakout to restraints control module)
- (in main body wiring harness, near breakout to g200)
- (in main body wiring harness, near breakout to instrument cluster) s208
- C175b
- C310a
- C310b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Driver safety belt retractor pretensioner (left side of vehicle floor)
- Driver seat belt buckle sensor (in driver's seat)
- Driver seat track position sensor (below driver seat)
- Fuse 10a
- G201
- G201 (behind right kick panel)
- Gnd
- Ground
- Hot in run or start
- Hs can +
- Hs can -
- Iso
- Left side impact sensor (base of left "b" pillar)
- Nca
- Pad ind
- Passenger air bag module
- Passenger safety belt retractor pretensioner (right side of vehicle floor)
- Pin shorting bars engaged when module connector is disconnected from harness shorting bars are connected between pins: 1-2, 3-4, 5-6, 13-14, 15-16 conn. c310a 1-2, 21-22 conn. c310b
- Powertrain control module (pcm) (left rear side of engine compt)
- Pwr
- Rdi
- Red
- Restraints control module (below center of dash)
- Right front impact severity sensor (on front right of engine compartment)
- Right side impact sensor (base of right "b" pillar)
- Ril
- S213 (in main body wiring harness, near breakout to c237)
- S217
- S301 (in power seats harness, in breakout to c311)
- S305
- Shorting bar
- Sig rtn
- Stage 1
- Stage 2
- Tone req
- Vpwr
- Vref
Supplemental Restraints Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005
List of elements for Supplemental Restraints Wiring Diagram (2 of 2) for Ford Crown Victoria S 2005:
- (behind left side of dash) warning lamps module
- (on steering column) deployable steering column
- Air bag ind
- Air bag sliding contact (at base of steering column)
- Analog
- C2145b
- C216a
- C216b
- C218a
- C2220b
- Central junction box (cjb) (below dash, left of steering column)
- Digital
- Driver air bag unit
- Fuse 10a
- G201 (behind right kick panel)
- Gnd
- Ground
- Hot in run or start
- Hs can +
- Hs can -
- Instrument cluster
- Left front impact severity sensor (on front left of engine compartment)
- Left side air bag bridge resistor (under driver's seat)
- Left side air bag module (in driver's seat)
- Lightining control module (behind center of dash)
- Nca
- Occupant classification sensor module (under passenger's seat)
- Passenger air bag deactivation (pad) indicator
- Passenger seat belt buckle sensor (in passenger's seat)
- Red
- Right side air bag bridge resistor (under passenger's seat)
- Right side air bag module (in passenger's seat)
- S217 (in main body wiring harness, near breakout to g200)
- S276 (in main wiring harness, near breakout to instrument cluster)
- Seat pressure sensor (below passenger seat)
- Seat sig
- Shorting bar
- Sig rtn
- Tan/ red
- Tan/red
- Tone request
- Vout
- Vpwr
- Vref
- W/ side air bags
- W/o side air bags
TRANSMISSION
A/T Wiring Diagram for Ford Crown Victoria S 2005
List of elements for A/T Wiring Diagram for Ford Crown Victoria S 2005:
- (at left rear of engine compt)
- (dash panel to headlamp junction harness, near breakout to c1019)
- (in dash panel to headlamp junction harness, left rear of engine compt) s118
- (in dash panel to headlamp junction harness, left rear of engine compartment) s118
- (in engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (in engine control sensor & fuel charge wiring harness, near breakout to turbine shaft speed sensor)
- (left rear of engine compt) s130
- (near breakout to battery junction box) s119
- (near breakout to battery junction box) s121
- (near breakout to g212)
- (on left side of transmission) digital transmission range (dtr) sensor
- (top of brake pedal support)
- 4r70w transmission
- Analog
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Bpp switch
- Brake pedal position (bpp) switch
- C175b
- C175e
- C175t
- C220a
- C2220b
- Central junction box (cjb) (below dash, left of steering column)
- Computer data lines system
- Digital
- Elect press
- Electronic pressure control solenoid
- Engine controls system
- Feps
- Floor shifter (w/center console)
- Fuse 10a
- Fuse 15a
- Fuse 30a
- G106
- G107
- G107 (at left rear of engine compt)
- G109 (at front of right fender)
- G212 (at left kick panel)
- Ground
- Harness, near breakout to c248)
- Hot at all times
- Hot in run or start
- Ignition coils relay
- Ignition power
- Instrument cluster
- Instrument cluster)
- Intake air temp
- Maf return
- Maf sensor sig
- Mass air flow/ intake air temperature (maf/iat) sensor (behind air cleaner assembly)
- Output shaft
- Output shaft speed (oss) sensor (left side of transmission)
- Overdrive cancel indicator
- Overdrive cancel switch (w/o center console)
- Pcm power diode
- Pcm power relay
- Powertrain control module (pcm) (left rear of engine compt)
- R p
- Red
- S117
- S146
- S147
- S164
- S267
- Scp +
- Scp -
- Shift sol a
- Shift sol b
- Shift solenoids
- Sig rtn
- Signal control
- Signal return
- Ss a
- Ss b
- Tci lamp
- Throttle position sensor (tps) (left side of engine)
- Torque conv
- Torque converter clutch (tcc) solenoid
- Tps
- Tr1
- Tr2
- Tr3a
- Tr4
- Trans cntrl sw
- Trans temp
- Transmission fluid temperature sensor
- Tss
- Turbine shaft speed sensor (left side of transmission)
- Vref
- W/ center console
- W/o center console
TRUNK, TAILGATE, FUEL DOOR
Trunk Release Wiring Diagram, Police Option for Ford Crown Victoria S 2005
List of elements for Trunk Release Wiring Diagram, Police Option for Ford Crown Victoria S 2005:
- (near breakout to c211) s266
- (not used)
- Accessory relay
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145a
- C2145c
- Circuit breaker 20a
- Decklid ajar switch
- Demand lighting output
- Emergency flasher relay block (in left rear of luggage compartment)
- G406 (at rear center of luggage compartment)
- Hot at all times
- Lighting control module (behind center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Luggage compartment lid release switch 2
- Pnk/
- Rear flasher relay
- S230 (in main body wiring harn, near breakout to temperature blend door actuator)
- S242
- S251 (near breakout to rear window defrost switch)
- S403
- S502
- W/ police option 1
- W/ police option 2
Trunk Release Wiring Diagram, with Keyless Entry for Ford Crown Victoria S 2005
List of elements for Trunk Release Wiring Diagram, with Keyless Entry for Ford Crown Victoria S 2005:
- (at left kick panel) g212
- (in breakout to instrument cluster) s240
- (near breakout to temperature blend door actuator)
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145a
- C2145c
- C220b
- C501b
- C501c
- Decklid ajar switch
- Demand lighting output
- Digital cluster
- Driver door module (bottom front of left front door)
- Fuse 20a
- G406 (at rear center of luggage compartment)
- Hot at all times
- Instrument cluster
- Lighting control module (behind center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Pnk/
- Release out
- Release sw
- S230
- S403
- S500
- S506 (near breakout to driver's door module)
- Trunk ajar input
Trunk Release Wiring Diagram, without Keyless Entry for Ford Crown Victoria S 2005
List of elements for Trunk Release Wiring Diagram, without Keyless Entry for Ford Crown Victoria S 2005:
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145a
- C2145c
- C220b
- Circuit breaker 20a
- Decklid ajar switch
- Demand lighting output
- Digital cluster
- G406 (at rear center of luggage compartment)
- Hot at all times
- Instrument cluster
- Lighting control module (behind center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (on center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Pnk/
- S230 (in main body wiring harness, near breakout to temperature blend door actuator)
- S240 (in main wiring harness, in breakout to instrument cluster)
- S242
- S403
- Trunk ajar input
WARNING SYSTEMS
Warning Systems Wiring Diagram, with Analog Cluster for Ford Crown Victoria S 2005
List of elements for Warning Systems Wiring Diagram, with Analog Cluster for Ford Crown Victoria S 2005:
- (at front of right fender) g109
- (behind right kick panel) g201
- (in main body wiring harness, near breakout to g200) s259
- (in power seats harness, in breakout to c311) s301
- (taxi)
- Acc
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C2145a
- C2145b
- C2145c
- C2212a
- C2212b
- C2220a
- C310a
- C310b
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820b
- Central junction box (cjb) (below dash, left of steering column)
- Door ajar indi- cator (taxi)
- Driver seat belt buckle sensor (in driver's seat)
- Driver side front door ajar switch (at top rear of left front door)
- Driver side rear door ajar switch (at rear of left rear door)
- Driver's ajar sw
- Early production
- Engine controls system
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G203 (behind right kick panel)
- Gnd
- Hot at all times
- Hot in run or acc
- Hot in start or run
- Ignition
- Ignition switch
- Instrument cluster
- Key in
- Late production
- Left seat track position sensor (below driver seat)
- Lighting control module (behind center of dash)
- Lock
- Off
- Pass ajar sw
- Passenger seat belt buckle sensor (in passenger's seat)
- Passenger side front door ajar switch (at top rear of right front door)
- Passenger side rear door ajar switch (at rear of right rear door) c820a
- Restraints control module (below center of dash)
- Run
- S202 (police)
- S207
- S210
- S226
- S227
- S238
- S247 (in main wiring harness, near breakout to c410)
- S276
- S305 (in main body wiring harness, near breakout to restraints control module)
- Safety belt ind
- Seatbelt sw
- Start
- Vbatt
- Vss
Warning Systems Wiring Diagram, with Digital Cluster for Ford Crown Victoria S 2005
List of elements for Warning Systems Wiring Diagram, with Digital Cluster for Ford Crown Victoria S 2005:
- (at front of left fender) g102
- (at front of right fender) g109
- (behind right kick panel) g203
- (bottom front of left front door) driver door module
- (in dash panel to headlamp junction harness, near breakout to g102) s104
- (in main body wiring harness, near breakout to g200) s259
- (in main wiring harness, near breakout to c410)
- (in power seats harness, in breakout to c311) s301
- (left rear of engine compartment) powertrain control module (pcm)
- (taxi)
- Abs
- Abs control module (at left front of engine compt)
- Acc
- Air bag
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- Brake fluid level switch (on brake fluid reservoir)
- C175b
- C2145a
- C2145b
- C2145c
- C220a
- C220c
- C2212a
- C2212b
- C310a
- C310b
- C501a
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Central junction box (cjb) (below dash, left of steering column)
- Door ajar ind
- Door ajar indicator (taxi)
- Driver seat belt buckle sensor (in driver's seat)
- Driver side front door ajar switch (at top rear of left front door)
- Driver side rear door ajar switch (at rear of left rear door)
- Driver's ajar sw
- Early production
- Engine controls system
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G201 (behind right kick panel)
- G212 (at left kick panel)
- Gnd
- Hazard
- Hazard ind
- Hot at all times
- Hot in run or acc
- Hot in start or run
- Ignition
- Ignition switch
- Instrument cluster
- Key in
- Late production
- Left seat track position sensor (below driver seat)
- Lighting control module (behind center of dash)
- Lock
- Low brake fluid level/ park brake
- Microprocessor
- Off
- Parking brake switch (behind left side of dash, on top of parking brake assembly)
- Pass ajar sw
- Passenger seat belt buckle sensor (in passenger's seat)
- Passenger side front door ajar switch (at top rear of right front door)
- Passenger side rear door ajar switch (at rear of right rear door)
- Restraints control module (below center of dash)
- Run
- S112
- S202 (police)
- S207
- S210
- S226
- S227
- S238
- S247
- S267
- S276
- S277 (in main wiring harness, near breakout to lighting control module)
- S282 (early production)
- S305 (in main body wiring harness, near breakout to restraints control module)
- Safety belt ind
- Speedometer
- Start
- Tone drive
- Tone drv
- Tone req
- Vbatt
- Vss
- Warning lamps module (behind left side of dash)
WIPER/WASHER
Wiper/Washer Wiring Diagram for Ford Crown Victoria S 2005
List of elements for Wiper/Washer Wiring Diagram for Ford Crown Victoria S 2005:
- (at front of left fender)
- 21. interval 1 22. interval 2 23. interval 3 24. interval 4 25. interval 5
- Battery junction box (bjb) (in right front of engine compt, behind battery)
- C202b
- C2145a
- C220a
- Central junction box (cjb) (below dash, left of steering column)
- Fuse 10a
- Fuse 15a
- Fuse 30a
- G102 (at front of left fender)
- G104
- G105
- G201 (behind right kick panel)
- G203 (behind right kick panel)
- High
- Hot at all times
- Hot in run or acc
- Instrument cluster
- Lighting control module (behind center of dash)
- Low
- Low washer fluid indicator
- Microprocessor
- Multi-function switch 0. off 2. low 1. high
- Nca
- Park
- Red
- Run
- S112
- S113
- S201
- S210
- Vbatt
- W/ air suspension compressor assembly
- W/o air suspension compressor assembly
- Wash switch
- Washer fluid level switch (digital) (in washer fluid reservoir)
- Windshield washer pump motor (in washer fluid reservoir)
- Windshield washer relay
- Windshield wiper motor (on left rear of engine compt)
- Wiper high/ low relay
- Wiper run/park relay