AIR CONDITIONING
Manual A/C Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for Manual A/C Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (2.7l: rear of engine) (4.0l: top center of engine) engine coolant temperature sensor
- 2.7l
- 4.0l
- A/c
- A/c amplifier (right side of dash)
- A/c compressor (left front of engine)
- A/c fuse 10a
- A/c lock sensor
- A/c magnetic clutch
- A/c thermistor 1 (behind center of dash)
- A29
- A33
- Ac1
- Acid
- Act
- Air inlet damper servo motor (center of dash)
- Ambient temperature sensor (behind front grille, below hood release assembly)
- B10
- Blower motor (below right side of dash, in blower housing)
- Blrh
- Def
- E10
- E11
- E13
- E14
- E17
- E22
- Ea (right front fender)
- Ea1
- Ecu-b fuse 7.5a
- Engine control module (behind right side of dash)
- Engine controls system
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Ethw
- Except tmmtx made
- Frs
- Gnd
- Heater relay
- Hot at all times
- Htr fuse 50a
- Ia1
- Ia4
- Ig+
- Ign
- Ih1
- Ii1
- Ij1
- In1
- In2
- Inner rear view mirror
- Instrument panel j/b 2 (right side of dash)
- Ip2
- J/c 5 (behind right side of dash)
- Lock
- Mg clt relay
- Mgc
- Mr/f
- Pnk
- Pressure switch (behind right front headlight)
- Prs
- Rdef
- Rec
- Red
- Sg 2
- Solf
- Spd
- Tach
- Tam
- Tamo
- Temp
- Thw
- Thwo
- Tmmtx made
- Ver1
Manual A/C Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Manual A/C Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- 4.0l
- A/c
- A/c control assembly
- A15
- A33
- Acid
- Air mix damper servo motor (center of dash)
- Air vent mode damper servo motor (center of dash)
- Amplifier
- Amsw
- Bb (under front passenger's seat)
- Blower resistor (center of dash)
- C11
- C13
- C14
- C16
- Combination meter
- Cpu
- Driver side j/b (left side of dash)
- F14
- Gauge fuse 7.5a
- Gnd
- Hot in run or start
- Ia1
- Ig+
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ill+
- Ill-
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- K13
- Max
- Mr/f
- Mset
- Off
- Pnk
- Rec
- Red
ANTI-LOCK BRAKES
Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (1 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (1 of 3) for Toyota Tacoma X-Runner 2013:
- (right side of dash) (a/t) instrument panel j/b 2
- +bm1
- +bm2
- +bs
- A-trac switch
- A33
- A39
- Abs 1 fuse 50a
- Abs 2 fuse 30a
- Atrc
- Brake fluid level warning switch (brake fluid reservoir)
- C17
- C18
- Canh
- Canl
- Csw
- Downhill assist control switch (if equipped)
- Driver side j/b (left side of dash)
- Ea (right front fender)
- Eb (near battery)
- Ecu-b fuse 7.5a
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Exi
- Exi3
- Exi4
- Fl+
- Fl-
- Fr+
- Fr-
- Gnd1
- Gnd2
- Gnd3
- H13
- Hdcs
- Hot at all times
- Hot in on or start
- Ia1
- Ia3
- Ig1
- Ig1 fuse 10a
- Ig2
- Ign fuse 15a
- Interior lights system
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- Lbl
- Park/ neutral position switch (a/t) (transmission)
- Pkb
- Pnk
- Red
- Rl+
- Rl-
- Rr+
- Rr-
- Skid control ecu w/ actuator (left rear of engine compt)
- Stp
- Stp2
- Stpo
- T17
- T18
- Traction control switch
- Transmissions system
- Vsc off switch
Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (2 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (2 of 3) for Toyota Tacoma X-Runner 2013:
- A-trac ind
- A/t
- Abs ind
- Auto lsd ind
- Bat
- Brake ind
- Buzzer
- C15
- C16
- Canh
- Canl
- Combination meter
- Cpu
- Dac ind
- Data link connector 3 (below left center of dash)
- Driver side j/b (left side of dash)
- Ess
- Gauge fuse 7.5a
- Hot in run or start
- Ia1
- Ib1
- Ic (center of dash)
- Instrument panel j/b 1 (left side of dash)
- J/c 5 (behind right side of dash)
- K13
- Left front speed sensor (left front hub assembly)
- M/t
- Parking brake switch (base of park brake lever)
- Pnk
- Rear speed sensor (rear differential)
- Red
- Right front speed sensor (right front hub assembly)
- Slip ind
- Steering sensor (steering wheel)
- Vsc off ind
Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (3 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Hydraulic Booster Type (3 of 3) for Toyota Tacoma X-Runner 2013:
- A12
- A13
- Ba (under driver's seat)
- C13
- C14
- C15
- Canh
- Canl
- D12
- Driver side j/b (left side of dash)
- E14
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- F10
- Gnd
- H18
- Hot at all times
- Hot in on or start
- Ia3
- Ie2
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 18 (rear of engine)
- J/c 19 (left side of dash)
- Pnk
- Stop fuse 10a
- Stop lamp switch (above brake pedal bracket)
- Stop lp ctrl relay
- Transmissions system
- Yaw rate sensor (under passenger seat)
Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (1 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (1 of 3) for Toyota Tacoma X-Runner 2013:
- +bs
- A/t
- Abs 1 fuse 50a
- Abs 2 fuse 30a
- C15
- C18
- Canh
- Canl
- Csw
- Data link connector 3 (below left center of dash)
- Dl nl
- Ea (right front fender)
- Ecu-b fuse 7.5a
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Exi
- Exi3
- Exi4
- F7 pnk
- Fl+
- Fl-
- Fr+
- Fr-
- Gnd1
- Gnd2
- Hot at all times
- Ia1
- Ia3
- Ic (center of dash)
- Ig1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (a/t) (right side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 5 (4wd) (behind right side of dash)
- M/t
- Neo
- Park/neutral position switch (a/t) (transmission)
- Parking brake switch (base of park brake lever)
- Pkb
- Pnk
- Red
- Rl+
- Rl-
- Rr+
- Rr-
- Skid control ecu w/ actuator (right rear of engine compt)
- Stop fuse 10a
- Stop lp ctrl relay (w/ trailer towing)
- Stp
- Stp2
- Stpo
- Traction control switch
- Transmissions system
- Vsc off switch
- W/ trailer towing
- W/o trailer towing
Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (2 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (2 of 3) for Toyota Tacoma X-Runner 2013:
- Abs ind
- Auto lsd ind
- Brake fluid level warning switch (brake fluid reservoir)
- Brake ind
- Buzzer
- C10
- C15
- C16
- Combination meter
- Cpu
- Driver side j/b (left side of dash)
- Eb (near battery)
- Gauge fuse 7.5a
- H13
- Hot in on or start
- Ia1
- Ib1
- Ig1 fuse 10a
- Ih1
- K13
- Left front speed sensor (left front hub assembly)
- Pnk
- Rear speed sensor (rear differential)
- Red
- Right front speed sensor (right front hub assembly)
- Slip ind
- Stop lamp switch (above brake pedal bracket)
- Trac off ind
- Vsc off ind
- W/ trailer towing
- W/o trailer towing
Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (3 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Anti-lock Brakes Wiring Diagram, Vacuum Booster Type (3 of 3) for Toyota Tacoma X-Runner 2013:
- 2.7l
- 4.0l
- A12
- A13
- Ba (under driver's seat)
- Bat
- C13
- C14
- Canh
- Canl
- D12
- Driver side j/b (left side of dash)
- E14
- E22
- Engine control module (behind right side of dash)
- Ess
- F10
- Gnd
- H18
- Hot in on or start
- Ia3
- Ib1
- Ie2
- Ig1 2 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 18 (rear of engine)
- J/c 19 (left side of dash)
- Red
- Steering sensor (steering wheel)
- Transmissions system
- W/ rear differential lock
- W/o rear differential lock
- Yaw rate sensor (under passenger seat)
ANTI-THEFT
Forced Entry Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Forced Entry Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Access cab
- Altb
- Be (left "b" pillar)
- Bf (right "c" pillar)
- Bf1
- Bg1
- Body ecu
- C10
- C16
- Dcty
- Door control receiver (right side of dash)
- Double cab
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- Driver's side door lock assembly
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- Front passenger's side door courtesy switch
- Front passenger's side door lock assembly
- Gnd
- H18
- Haz
- Horn
- Horn relay
- Hot at all times
- Hot in run or start
- I16
- Ic (center of dash)
- Ic6
- Ig1 2 fuse 10a
- Ik3
- Il1
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 4 & 5 (behind right side of dash)
- J15
- K10
- Ksw
- Left rear door courtesy switch
- Left rear lower side door courtesy switch
- Left rear upper side door courtesy switch
- Lswd
- Lswp
- Pcty
- Prg
- Rcty
- Rda
- Red
- Right rear door courtesy switch
- Right rear lower side door courtesy switch
- Right rear upper side door courtesy switch
- Turn signal flasher (w/ trailer towing) (left side of dash)
- Unlock warning switch
- W/ door lock control
- W/o door lock control
Immobilizer Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Immobilizer Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (4.0l) (right rear of engine compt)
- (rear of cylinder head) (2.7l) eg
- 2.7l
- 4.0l
- Access cab
- Agnd
- Ant1
- Ant2
- Batt
- Bb (under front passenger's seat)
- Bf1
- C16
- Code
- Cty
- Data link connector 3 (below left center of dash)
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- E01
- E02
- E03
- E04
- E05
- E11
- E12
- E13
- E14
- E19
- E20
- E21
- E22
- Ecu-b fuse 7.5a
- Ee eh (2.7l) (rear of cylinder head)
- Ef (4.0l) (left rear of engine compt)
- Efi fuse 20a
- Efii
- Efio
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Gnd
- Hazard warning signal switch assembly
- Hot at all times
- Hot in run or start
- I15
- Ia1
- Ic (center of dash)
- Ign fuse 15a
- Igsw
- Il1
- Imi
- Imo
- Ind
- Instrument panel j/b 1 (left side of dash)
- J/c 12 (2.7l) (behind right side of dash)
- J/c 5 (behind right side of dash)
- J14
- K10
- Ksw
- Me01
- Red
- Security indicator light
- Sil
- Transponder key amplifier (left side of dash)
- Transponder key coil
- Transponder key ecu (left side of dash)
- Txct
- Unlock warning switch
- Vc5
BODY CONTROL MODULES
Body Control Modules Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Body Control Modules Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Access cab
- Act+
- Act-
- Actd
- Acty
- Altb
- Anti-lock brakes, instrument cluster & headlights systems
- Ba (under driver's seat)
- Bd (left rear frame rail)
- Be (left "b" pillar)
- Bf1
- Body ecu (driver side j/b)
- Bzr
- C10
- C16
- Dbkl
- Dcty
- Dim
- Door locks system
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Drl
- E11
- E12
- Ecu-b fuse 7.5a
- Ecub
- Ehw
- Engine room r/b (left front of engine compt)
- Except tmmtx made
- Exterior lights & headlights systems
- Exterior lights system
- F10
- F11
- Flash relay
- Gnd
- H18
- H22
- H23
- H24
- Haz
- Head
- Headlights system
- Horn
- Horns system
- Hot at all times
- Hot in on or start
- Hrly
- I14
- I16
- I17
- I18
- I19
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ile
- Instrument cluster & interior lights systems
- Instrument cluster system
- Interior lights system
- J/c 1 (left kick panel)
- J/c 4 & 5 (behind right side of dash)
- J15
- K10
- K13
- Ksw
- Lswd
- Lswp
- O11
- O12
- P/w relay
- Pcty
- Pkb
- Pnk
- Prg
- Pws
- Rcty
- Rda
- Red
- Starting/charging system
- Tail
- Tail relay
- Tmmtx made
- Trly
- Ul1
- Ul2
- Ul3
- W/ door lock control
- W/o door lock control
- W/o drl & w/o trailer towing
COMPUTER DATA LINES
Computer Data Lines Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Computer Data Lines Wiring Diagram for Toyota Tacoma X-Runner 2013:
- 2.7l
- 4.0l
- A/c amplifier (right side of dash)
- A18
- A21
- Air bag sensor assembly center (center of dash)
- B17
- B18
- Bat
- Bh1
- Bj2
- Canh
- Canl
- Combination meter
- Data link connector 3 (below left center of dash)
- Dia
- E14
- E22
- Ee (4.0l) (right rear of engine compt)
- Eh (2.7l) (rear of cylinder head)
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Hot at all times
- Ia1
- Ia3
- Ic (center of dash)
- Ie2
- Ign
- Il1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 18 (rear of engine)
- J/c 19 (left end of dash)
- J/c 4 & 5 (behind right side of dash)
- Obd fuse 7.5a
- Occupant classification ecu (front passenger's seat bottom)
- Sil
- Skid control ecu w/ actuator (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt)
- Steering sensor (steering wheel)
- Tac
- Tach
- Tire pressure warning ecu
- Transponder key ecu (left side of dash)
- W/ bench seat
- W/ hydraulic booster type
- W/ separate seat
- W/ vacuum booster type
- Yaw rate sensor (under passenger seat)
CRUISE CONTROL
2.7L
2.7L, Cruise Control Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Cruise Control Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- +bm
- Accelerator position sensor (behind left side of dash)
- Batt
- C13
- C14
- C15
- Canh
- Canl
- Ccs
- Computer data lines system
- Cruise control clutch switch (m/t) (bracket above clutch pedal)
- Driver side j/b (left side of dash)
- E03
- E04
- E17
- E19
- E20
- E21
- E22
- Efi main fuse 20a
- Eg (rear of cylinder head)
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- Eta
- Etcs fuse 10a
- Ge01
- H13
- Hot at all times
- Hot in on or start
- Hot in run or start
- I15
- Ia1
- Ia3
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ign fuse 15a
- Igsw
- Ii1
- Instrument panel j/b (left side of dash)
- Instrument panel j/b 1 (left side of dash)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- Nca
- Pnk
- Red
- Spd
- St1-
- Stop fuse 10a
- Stop lamp switch (above brake pedal bracket)
- Stop lp ctrl relay (w/ trailer towing)
- Stp
- Throttle body assembly (left top of engine)
- Vcp2
- Vcpa
- Vcta
- Vpa
- Vpa2
- Vta1
- Vta2
- W/ trailer towing
- W/o trailer towing
2.7L, Cruise Control Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Cruise Control Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- (left kick panel)
- (right side of dash) instrument panel j/b 2
- +res
- -set
- A/t
- A18
- C12
- C16
- Cancel
- Canh
- Canl
- Cccl
- Combination meter
- Computer data lines system
- Cpu
- Cruise control switch
- Cruise ind
- Driver side j/b (left side of dash)
- E15
- Eh (rear of cylinder head)
- Fl+
- Fl-
- Fr+
- Fr-
- Gauge fuse 7.5a
- Hot in on or start
- Ia1
- Ib1
- Ih1
- Im1
- J/c 1
- Left front speed sensor (left front hub assembly)
- M/t
- On- off
- Park/neutral position switch (a/t) (transmission)
- Pnk
- Rear speed sensor (rear differential)
- Red
- Right front speed sensor (right front hub assembly)
- Rl+
- Rl-
- Rr+
- Rr-
- Shift control ecu
- Skid control ecu w/ actuator (vacuum booster type: right rear of engine compt)
- Sp1
- Spiral cable (behind left side of dash)
- Stp
- Stp2
- Stpo
- Voltage inverter (left rear of vehicle compt)
4.0L
4.0L, Cruise Control Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Cruise Control Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (above brake pedal bracket) stop lamp switch
- (left kick panel) j/c 1
- (right side of dash) instrument panel j/b 2
- +bm
- +res
- -set
- A18
- Accelerator position sensor (behind left side of dash)
- B12
- Batt
- C12
- C13
- C14
- C15
- Cancel
- Canh
- Canl
- Cccl
- Ccs
- Combination meter
- Compt)
- Computer data lines system
- Cpu
- Cruise control clutch switch (m/t) (above clutch pedal bracket)
- Cruise control switch
- Cruise ind
- Driver side j/b (left side of dash)
- E01
- E02
- E03
- E04
- E05
- E11
- E12
- E13
- E14
- E15
- Ea1
- Ee (right rear of engine
- Ee (right rear of engine compt)
- Ef (left rear of engine compt)
- Efi main fuse 20a
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- Eta
- Etcs fuse 10a
- Gauge fuse 7.5a
- Ge01
- H13
- Hot at all times
- Hot in on or start
- Hot in run or start
- I15
- Ia1
- Ia3
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ign fuse 15a
- Igsw
- Ii1
- Im1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 5 (behind right side of dash)
- M/t
- Me01
- Nca
- On- off
- Pnk
- Red
- Spd
- Spiral cable (behind left side of dash)
- St1-
- Stop fuse 10a
- Stop lp ctrl relay
- Stp
- Throttle body assembly (front top of engine)
- Vcp2
- Vcpa
- Vcta
- Voltage inverter (left rear of vehicle compt)
- Vpa
- Vpa2
- Vta1
- Vta2
- W/ hydraulic booster type
- W/ trailer towing
- W/ vaccum booster type
- W/o trailer towing
4.0L, Cruise Control Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Cruise Control Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- Booster type
- Canh
- Canl
- Computer data lines system
- Fl+
- Fl-
- Fr+
- Fr-
- Ia1
- Ib1
- Ih1
- Left front speed sensor (left front hub assembly)
- Park/neutral position switch (a/t) (transmission)
- Pnk
- Rear speed sensor (rear differential)
- Red
- Right front speed sensor (right front hub assembly)
- Rl+
- Rl-
- Rr+
- Rr-
- Skid control ecu w/ actuator (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt)
- Sp1
- Stp
- Stp2
- Stpo
- W/ hydraulic booster type
- W/ vacuum
ENGINE PERFORMANCE
2.7L
2.7L, Engine Performance Wiring Diagram (1 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (1 of 7) for Toyota Tacoma X-Runner 2013:
- (behind left side of dash)
- (power steering pump) power steering oil pressure switch
- +bm
- 4wd
- A/f htr fuse 15a
- A/f htr relay
- A10
- A11
- A30
- A31
- A33
- Ac1
- Accelerator position sensor
- Act
- Aidi
- Aip
- Air conditioning system
- Airp
- Airv
- Batt
- Bd (left rear frame rail)
- C/opn relay
- Canh
- Canl
- Computer data lines system
- Driver side j/b (left side of dash)
- E21
- E22
- Ea (right front fender)
- Efi fuse 10a
- Efi main fuse 20a
- Efi main relay
- Efii
- Efio
- Els
- Els3
- Engine control module (behind right side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- Fuel suction pump & gauge assembly (fuel tank)
- Hot at all times
- Ia1
- Ib1
- Igsw
- Ii1
- Imi
- Imo
- Instrument cluster system
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- Mpmp
- Mrel
- Nsw
- Psw
- Red
- Spd
- St1-
- Sta
- Starting/charging system
- Stp
- Tach
- Transmissions system
- Transponder key ecu (left side of dash)
- Vcp2
- Vcpa
- Vpa
- Vpa2
- Vpmp
2.7L, Engine Performance Wiring Diagram (2 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (2 of 7) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) j/c 4 & 5
- (top of engine)
- (under front passenger's seat) voltage inverter
- A17
- A18
- Acc
- B10
- B11
- C13
- Canister pressure sensor
- Canister pump module (under center of vehicle bed)
- Driver side j/b (left side of dash)
- Ea1
- Eh (rear of cylinder head)
- Fuel injector 1
- Fuel injector 2
- Fuel injector 3
- Fuel injector 4
- Gauge fuse 7.5a
- Hot at all times
- Hot in on or start
- Hot w/ tail relay energized
- I15
- Ib1
- Id2
- Ig2
- Ign fuse 15a
- Ignition switch
- Ih1
- Im1
- Instrument panel j/b 2 (right side of dash)
- Leak detection pump
- Lock
- Off
- Out
- Red
- Start
- Tail fuse 10a
- Vent valve
2.7L, Engine Performance Wiring Diagram (3 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (3 of 7) for Toyota Tacoma X-Runner 2013:
- (a/t) air pump htr relay
- (above brake pedal bracket) stop lamp switch
- (automatic transmission) a/t fluid temperature sensor
- (left side of dash) instrument panel j/b 1
- (rear of cylinder head) eg
- Air pump fuse 50a
- Air pump htr fuse 10a
- Alt
- Charging system starting/
- E01
- E02
- E17
- E20
- E2g
- Eh (rear of cylinder head)
- Eknk
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Eppm
- Eta
- Etcs fuse 10a
- Etha
- Ethw
- Hot at all times
- Igf1
- Igt1
- Igt2
- Igt3
- Igt4
- Knk1
- Me01
- Pnk
- Ppmp
- Red
- Stop fuse 10a
- Tha
- Thoc
- Thw
- Vcpp
- Vcta
- Vta1
- Vta2
2.7L, Engine Performance Wiring Diagram (4 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (4 of 7) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) j/c 12
- (left top of engine) throttle body assembly
- (rear of cylinder head) eh
- (right side of engine compt)
- (top of cylinder head cover)
- (top of engine)
- A/t
- Air injection control driver
- Air pump (right front of engine compt)
- Air switching valve (right side of engine compt)
- Aphg
- Apht
- Bat
- E2g
- Ea (right front fender)
- Ea1
- Ef1
- Eh (rear of cylinder head)
- Gnd
- Ia1
- Igf
- Ignition coil 1
- Ignition coil 2
- Ignition coil 3
- Ignition coil 4
- Igt1
- Igt2
- Igt3
- Igt4
- Knock control sensor (bank 1) (left side of engine)
- M/t
- Mass air flow meter (part of air intake assembly, next to air cleaner box)
- Nca
- Noise filter (ignition)
- Pnk
- Sip
- Siv
- Tha
2.7L, Engine Performance Wiring Diagram (5 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (5 of 7) for Toyota Tacoma X-Runner 2013:
- A/t oil temperature
- A12
- A13
- A14
- A15
- A18
- B10
- Buzzer
- C10
- C12
- Canh
- Canl
- Combination meter
- Computer data lines system
- Cpu
- Eh (rear of cylinder head)
- Engine coolant temperature sensor (rear of engine)
- Engine oil pressure switch (right front of engine)
- Engine room j/b (left side of engine compt)
- Fuel ind
- Ia1
- Ind
- Ind lamp malfunction
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 12 (behind right side of dash)
- Nca
- Oil pressure ind
- Red
- Skid control ecu w/ actuator (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt)
- Sp1
2.7L, Engine Performance Wiring Diagram (6 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (6 of 7) for Toyota Tacoma X-Runner 2013:
- (right side of dash) instrument panel j/b 2
- (under center console) shift lock control ecu
- A10
- B11
- C11
- C13
- C14
- C16
- Camshaft position sensor (left side of engine)
- Camshaft timing oil control valve (front of engine)
- Crankshaft position sensor (front of engine)
- E12
- E15
- Gnd
- Ij1
- Nca
- Ne-
- Park/neutral position switch (transmission)
- Red
- Starting/ charging system
- Vsv (purge) (left side of engine compt)
2.7L, Engine Performance Wiring Diagram (7 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Engine Performance Wiring Diagram (7 of 7) for Toyota Tacoma X-Runner 2013:
- (left side of engine compt) engine room j/b
- (left side of transmission assembly) transmission revolution sensor (turbine)
- (rear of cylinder head) eg
- (right rear of engine) air pressure sensor
- A1a+
- A1a-
- Aip
- Air fuel ratio sensor (bank 1 sensor 1) (exhaust system, rear of engine)
- Driver side j/b (left side of dash)
- E03
- E04
- E18
- E19
- Ea1
- Eaip
- Eg (rear of cylinder head)
- Electronically controlled transmission solenoid (transmission)
- Engine control module (behind right side of dash)
- Etho
- Ex1b
- Ge01
- H13
- Ha1a
- Hai1
- Heated oxygen sensor (bank 1 sensor 2) (exhaust manifold, after catalytic converter)
- Hot in on or start
- Ht1b
- Ig1 fuse 10a
- Ih1
- Ih2
- Nc0-
- Nca
- Nco+
- Ne+
- Ne-
- Oc1+
- Oc1-
- Ox1b
- Pnk
- Prg &
- Red
- Slt+
- Slt-
- Slu+
- Slu-
- Sp2+
- Sp2-
- Tho1
- Transmission revolution sensor (electronically controlled transmission) (right rear of transmission assembly)
4.0L
4.0L, Engine Performance Wiring Diagram (1 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (1 of 7) for Toyota Tacoma X-Runner 2013:
- (behind left side of dash)
- +b2
- 4wd
- A/f heater fuse 15a
- A/f heater relay
- A10
- A11
- A30
- A31
- A33
- Ac1
- Accelerator position sensor
- Act
- Aip
- Aip2
- Air conditioning system
- Anti-theft system
- Batt
- Bd (left rear frame rail)
- C/opn relay
- Canh
- Canl
- Ccs
- Computer data lines system
- Cruise control system
- Driver side j/b (left side of dash)
- E13
- E14
- Ea (right front fender)
- Eb (near battery)
- Efi fuse 10a
- Efi fuse 20a
- Efi relay
- Els
- Els2
- Engine control module (behind right side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- F/ps
- Fpr
- Fuel pump relay
- Fuel pump resistor
- Fuel suction pump & gauge assembly (fuel tank)
- Hot at all times
- Ia1
- Ib1
- Igsw
- Ih1
- Im1
- Imi
- Imo
- Instrument cluster system
- Mpmp
- Mrel
- Red
- Spd
- St1-
- Sta
- Starting/charging system
- Stp
- Tach
- Thwo
- Transmissions system
- Vcp2
- Vcpa
- Vpa
- Vpa2
- Vpmp
4.0L, Engine Performance Wiring Diagram (2 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (2 of 7) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) j/c 5
- (center of dash) diode (tail)
- (left rear of vehicle compt) voltage inverter
- (top of engine)
- A18
- Acc
- B10
- B11
- C13
- Canister pressure sensor
- Canister pump module (under center of vehicle bed)
- Data link connector 3 (below left center of dash)
- Driver side j/b (left side of dash)
- Ea1
- Ee (right rear of engine compt)
- Fuel injector 1
- Fuel injector 2
- Fuel injector 3
- Fuel injector 4
- Fuel injector 5
- Fuel injector 6
- Gauge fuse 7.5a
- H13
- Hot at all times
- Hot in on or start
- Hot w/ tail relay energized
- I15
- Ib1
- Ic (center of dash)
- Id2
- If1
- Ig1 fuse 10a
- Ig2
- Ign fuse 15a
- Ignition switch
- Ih1
- Instrument panel j/b 2 (right side of dash)
- J/c 4 & 5 (behind right side of dash)
- Leak detection pump
- Lock
- Off
- Out
- Pnk
- Red
- Start
- Tail fuse 10a
- Vent valve
- W/ hydraulic booster type, vacuum booster type w/ trailer towing
- W/ vacuum booster type w/o trailer towing
4.0L, Engine Performance Wiring Diagram (3 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (3 of 7) for Toyota Tacoma X-Runner 2013:
- (above brake pedal bracket) stop lamp switch
- (left side of dash) instrument panel j/b 1
- (right side of dash) instrument panel j/b 2
- A/pump fuse 50a
- Ai valve fuse 10a
- Ai valve relay
- Airv
- E01
- E02
- E03
- E04
- E05
- E12
- Ea1
- Ee (right rear of engine compt)
- Ef (left rear of engine compt)
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- Etcs fuse 10a
- Ex1b
- Ex2b
- Ha1a
- Ha2a
- Hot at all times
- Ht1b
- Ht2b
- Ia3
- If1
- Me01
- Ne+
- Ne-
- Oc2+
- Oc2-
- Ox1b
- Ox2b
- Pnk
- Red
- Stop fuse 10a
- Stop lp ctrl relay
- Vcv1
- Vcv2
- Vv1+
- Vv1-
- Vv2+
- Vv2-
- W/ hydraulic booster type, vacuum booster type w/ trailer towing
- W/ vacuum booster type w/o trailer towing
4.0L, Engine Performance Wiring Diagram (4 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (4 of 7) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) j/c 12
- (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt) skid control ecu w/ actuator
- (rear of engine)
- (right rear of engine compt) ee
- (top of cylinder head cover)
- Crankshaft position sensor (front of engine)
- Ed (right rear of engine compt)
- Gnd
- Heated oxygen sensor (bank 1 sensor 2) (exhaust system, rear of engine)
- Heated oxygen sensor (bank 2 sensor 2) (rear of engine, in left bank of exhaust)
- Ht1b
- Ht2b
- If1
- Igf
- Ignition coil 1
- Ignition coil 2
- Ignition coil 3
- Ignition coil 4
- Ignition coil 5
- Ignition coil 6
- Igt1
- Igt2
- Igt3
- Igt4
- Igt5
- Igt6
- Left camshaft timing oil control valve (top center of engine)
- Left vvt sensor (left front of engine)
- Nca
- Noise filter (ignition)
- Ox1b
- Ox2b
- Pnk
- Red
- Right vvt sensor (top right front of engine)
- Stpo
- Vvl+
- Vvl-
- Vvr+
- Vvr-
4.0L, Engine Performance Wiring Diagram (5 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (5 of 7) for Toyota Tacoma X-Runner 2013:
- A/t oil tempe- rature ind
- A13
- A14
- A15
- A18
- Air pump htr relay
- B10
- C10
- Combination meter
- Cpu
- Ee (right rear of engine compt)
- Engine coolant temperature sensor (top center of engine)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Ih1
- Ii1
- Ij1
- J/c 1 (left kick panel)
- J/c 12 (behind right side of dash)
- J/c j4 & j5 (behind right side of dash)
- Malfunction ind lamp
- Pnk
- Red
4.0L, Engine Performance Wiring Diagram (6 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (6 of 7) for Toyota Tacoma X-Runner 2013:
- (right front fender) ea
- (right side of dash) instrument panel j/b 2
- (right side of engine compt)
- (under center console) shift lock control ecu
- +bl
- A10
- A20
- Aip
- Aip2
- Air injection control driver
- Air pump (right front of engine compt)
- Air switching valve (bank 1)
- Air switching valve (bank 2)
- Aph+
- Aphg
- B11
- B12
- Bat
- C11
- C14
- E11
- E14
- E15
- E22
- E2g
- Ea1
- Ee2
- Gnd
- Gndl
- If1
- Ih1
- Knock control sensor (bank 1) (top front of engine)
- Knock control sensor (bank 2) (top front of engine)
- Mass air flow meter (part of air intake assembly, next to air cleaner box)
- Nca
- Park/neutral position switch (transmission)
- Pnk
- Red
- Sip
- Siv
- Starting/ charging system
- Tha
- Vc2
- Vsv (acis) (rear top center of engine)
- Vsv (purge) (left side of engine compt)
4.0L, Engine Performance Wiring Diagram (7 of 7) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Engine Performance Wiring Diagram (7 of 7) for Toyota Tacoma X-Runner 2013:
- (exhaust system, rear of engine) air fuel ratio sensor (bank 1 sensor 1)
- (front top of engine) throttle body assembly
- (left side of engine compt) engine room j/b
- (right rear of engine compt) ee
- (right rear of engine) air fuel ratio sensor (bank 2 sensor 1)
- (right rear of transmission assembly) transmission revolution sensor (electronically controlled transmission)
- +bm
- A1a+
- A1a-
- A2a+
- A2a-
- Acis
- Aidi
- Airi
- Airp
- E10
- E11
- E2g
- Ea1
- Ekn2
- Eknk
- Electronically controlled transmission solenoid (transmission)
- Engine control module (behind right side of dash)
- Eta
- Etha
- Ethw
- Ge01
- Ha1a
- Ha2a
- Hai1
- If1
- Igf1
- Igt1
- Igt2
- Igt3
- Igt4
- Igt5
- Igt6
- Knk1
- Knk2
- Nca
- Nsw
- Nt+
- Nt-
- Oc1+
- Oc1-
- Pnk
- Power steering oil pressure switch (power steering pump)
- Ppmp
- Prg
- Psw
- Red
- Right camshaft timing oil control valve (top center of engine)
- Sl1+
- Sl1-
- Sl2+
- Sl2-
- Slt+
- Slt-
- Slu+
- Slu-
- Sp2+
- Sp2-
- Starting/charging system
- Th01
- Th02
- Tha
- Thw
- Transmission revolution sensor (turbine) (left side of transmission assembly)
- Vcta
- Vta1
- Vta2
EXTERIOR LIGHTS
Backup Lamps Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Backup Lamps Wiring Diagram for Toyota Tacoma X-Runner 2013:
- 2.7l
- 4.0l
- A/t
- B/up
- B11
- Backup lamp
- Backup lamp relay (behind right side of dash)
- Backup lamp switch (right side of transmission)
- Bd (left rear frame rail)
- Be1
- Bkup lp fuse 10a
- C10
- C17
- Combination meter
- Driver side j/b (left side of dash)
- E19
- Engine control module (behind right side of dash)
- Except tmmtx made
- H11
- H13
- Hot in on or start
- Id2
- Ig1 fuse 10a
- Ih1
- In1
- In2
- Inner rear view mirror
- Instrument panel j/b 2 (right side of dash)
- Ip1
- J/c 13 (behind right kick panel)
- Left rear combin- -ation lamp
- M/t
- Park/ neutral position switch (transmission)
- Pnk
- Red
- Rev
- Right rear combin- -ation lamp
- Tmmtx made
- Trailer socket (left kick panel)
Exterior Lamps Wiring Diagram, with Trailer Tow (1 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, with Trailer Tow (1 of 4) for Toyota Tacoma X-Runner 2013:
- (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt) skid control ecu w/ actuator
- Bd (left rear frame rail)
- Be2
- Body ecu
- Bulb type
- C11
- C15
- C16
- Cruise control system
- D10
- D13
- Dcty
- Driver side j/b (left side of dash)
- Drl
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- Gnd
- H18
- Haz
- Hot at all times
- Hot in on or start
- I10
- Ia3
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/b fuse 50a
- J/c 1 (left kick panel)
- J15
- J19
- Led type
- Left license plate lamp
- Left rear combination lamp
- Pcty
- Pnk
- Rcty
- Red
- Right license plate lamp
- Right rear combination lamp
- Side marker
- Stop
- Stop fuse 10a
- Stop lamp switch (bracket, above brake pedal)
- Stop lp ctrl relay
- Stp
- Stp2
- Stpo
- Tail
- Tail fuse 10a
- Tail relay
- Tail/side marker
- Tail/stop
- To driver side j/b (diagram 3 of 4)
- Trly
- Turn
- W/ hydraulic booster type
- W/ vacuum booster type
Exterior Lamps Wiring Diagram, with Trailer Tow (2 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, with Trailer Tow (2 of 4) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) (except usa) j/c 4
- (behind right side of dash) engine control module
- (under center console) shift lock control ecu
- 2.7l
- 4.0l
- Access cab
- B13
- Ba (under driver's seat)
- C18
- Center stop lamp
- Combination meter
- D11
- Double cab
- Driver side j/b (left side of dash)
- E14
- E22
- Ground distribution system
- H18
- I11
- I12
- Ia3
- Ic1
- Ic7
- Ik4
- Instrument panel j/b 1 (left side of dash)
- Ir1
- J/c 1 (left kick panel)
- J/c 2 (behind left side of dash)
- J/c j13 (behind right kick panel)
- Left outer mirror turn view mirror (if equipped)
- Left turn ind
- Pnk
- Right outer mirror view mirror (if equipped)
- Right turn ind
- Stp
- Tail ind
- Turn
Exterior Lamps Wiring Diagram, with Trailer Tow (3 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, with Trailer Tow (3 of 4) for Toyota Tacoma X-Runner 2013:
- C11
- Combination switch
- Driver side j/b (left side of dash)
- Drl
- Engine room r/b (left front of engine compt)
- From body ecu (diagram 1 of 4)
- Haz
- Hazard switch
- Hazard warning signal switch assembly
- Head
- Hot at all times
- Hot in on or start
- I20
- Ic (center of dash)
- Ig1 fuse 10a
- Ij1
- Ir1
- J/c 13 (behind right kick panel)
- J/c j4 & j5 (behind right side of dash)
- J11
- J18
- Left
- Light control switch
- Ltot
- Ltrn
- M10
- M11
- Off
- Pnk
- Red
- Right
- Rtot
- Rtrn
- Stin
- Tail
- Towing fuse 30a
- Trn & haz fuse 15a
- Turn signal flasher (left side of dash)
- Turn switch
- W/ drl
Exterior Lamps Wiring Diagram, with Trailer Tow (4 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, with Trailer Tow (4 of 4) for Toyota Tacoma X-Runner 2013:
- A33
- A34
- A35
- A37
- B/up
- Backup lamps circuit
- Batt
- Batt chg fuse 30a
- Batt chg relay
- Bd (left rear frame rail)
- Be1
- Brk
- C13
- C14
- Driver side j/b (left side of dash)
- Ea (right front fender)
- Eb (near battery)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Gnd
- H10
- H11
- Hot at all times
- Hot in on or start
- Ia4
- Ib1
- Id2
- Ig1 2 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Ir1
- J/c 1 (left kick panel)
- J/c j20 (left side of dash)
- Left headlight assembly
- Marker
- Parking
- Red
- Right headlight assembly
- Stop
- Sttl
- Sttr
- Tail
- Towing brake controller (left side of dash)
- Towing brk fuse 30a
- Towing tail fuse 30a
- Towing tail relay
- Trailer socket (if equipped) (left kick panel)
- Turn
Exterior Lamps Wiring Diagram, without Trailer Tow (1 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, without Trailer Tow (1 of 3) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) engine control module
- (under center console) shift lock control ecu
- 2.7l
- 4.0l
- B13
- Bd (left rear frame rail)
- Bulb type
- C11
- C15
- C16
- Cruise control system
- D10
- D13
- Dcty
- Driver side j/b (left side of dash)
- E14
- E22
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- Gnd
- H18
- Haz
- Hot at all times
- Hot in on or start
- Ia3
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/b fuse 50a
- J/c 1 (left kick panel)
- J15
- Led type
- Left license plate lamp
- Left rear combination lamp
- Pcty
- Pnk
- Rcty
- Red
- Right license plate lamp
- Right rear combination lamp
- Side marker
- Skid control ecu w/ actuator (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt)
- Stop
- Stop fuse 10a
- Stop lamp switch (bracket, above brake pedal)
- Stop lp ctrl relay (w/ hydraulic booster type)
- Stp
- Stp2
- Stpo
- Tail body ecu
- Tail fuse 10a
- Tail relay
- Tail/side marker
- Tail/stop
- To flash relay (diagram 2 of 3)
- Trly
- Turn
- W/ hydraulic booster type
- W/ vacuum booster type
Exterior Lamps Wiring Diagram, without Trailer Tow (2 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, without Trailer Tow (2 of 3) for Toyota Tacoma X-Runner 2013:
- (left side of dash) driver side j/b
- Access cab
- Ba (under driver's seat)
- C18
- Center stop lamp
- Combination meter
- D11
- Double cab
- Ehw
- Engine room r/b (left front of engine compt)
- Flash relay
- From body ecu (diagram 1 of 3)
- Gnd
- Ground distribution system
- H18
- Hot at all times
- Hot in on or start
- I11
- I12
- Ia3
- Ic1
- Ic7
- Ig1 fuse 10a
- Ik4
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 4 (except usa) (behind right side of dash)
- J/c j4 & j5 (behind right side of dash)
- J11
- J18
- Left outer mirror turn view mirror (if equipped)
- Left turn ind
- Pnk
- Right outer mirror view mirror (if equipped)
- Right turn ind
- Short pin
- Tail ind
- Trn-haz fuse 15a
- Turn
Exterior Lamps Wiring Diagram, without Trailer Tow (3 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Exterior Lamps Wiring Diagram, without Trailer Tow (3 of 3) for Toyota Tacoma X-Runner 2013:
- A33
- A35
- A37
- C11
- Combination switch
- Ea (right front fender)
- Eb (near battery)
- Engine room j/b (left side of engine compt)
- H10
- H11
- Hazard switch
- Hazard warning signal switch assembly
- Head
- Ic (center of dash)
- Ij1
- J/c 13 (behind right kick panel)
- J/c j20 (left side of dash)
- J/c j4 & j5 (behind right side of dash)
- Left
- Left headlight turn assembly
- Light control switch
- Marker
- Off
- Parking
- Right
- Right headlight turn assembly
- Tail
- Turn signal switch
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram (1 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Ground Distribution Wiring Diagram (1 of 4) for Toyota Tacoma X-Runner 2013:
- (4wd) (4wd position) transfer indicator switch
- (4wd) (l4 position) transfer indicator switch
- (4wd) add actuator assembly
- (4wd) transfer shift actuator assembly
- (w/ cruise control) spiral cable
- 2.7l
- 4.0l
- A17
- A18
- A19
- Air fuel ratio sensor (bank 1 sensor 1) shield
- Air fuel ratio sensor (bank 2 sensor 1) shield
- Air switching valve
- Air switching valve (bank 1)
- Air switching valve (bank 2)
- Camshaft position sensor shield
- Canister pump module
- Crank- shaft position sensor shield
- Crankshaft position sensor shield
- Data link connector 3
- E11
- E12
- E19
- E20
- Ec1
- Ee (4.0l) (right rear of engine compt)
- Ef (4.0l) (left rear of engine compt)
- Eg (2.7l) (rear of cylinder head)
- Eh (2.7l) (rear of cylinder head)
- Engine control module
- From instrument panel j/b 2 (diagram 1 of 4)
- Heated oxygen sensor (bank 1 sensor 2) shield
- Heated oxygen sensor (bank 2 sensor 2) shield
- Id2
- Ignition coil 1
- Ignition coil 2
- Ignition coil 3
- Ignition coil 4
- Ignition coil 5
- Ignition coil 6
- Instrument panel j/b 2 (right side of dash)
- Junction connector (behind right side of dash)
- Knock control sensor (bank 1) shield
- Knock control sensor (bank 2) shield
- Nca
- Noise filter (ignition)
- To ground ee (diagram 1 of 4)
Ground Distribution Wiring Diagram (2 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Ground Distribution Wiring Diagram (2 of 4) for Toyota Tacoma X-Runner 2013:
- (120v) rear power point socket assembly
- (120v) voltage inverter
- (2.7l) engine control module
- (2wd)
- (4wd)
- (access cab) right rear lower side door courtesy switch
- (access cab) right rear upper side door courtesy switch
- (if equipped) downhill assist control switch
- (w/ bench seat)
- (w/ built-in type amplifier) radio receiver assembly
- (w/ built-in type amplifier) speaker (woofer)
- (w/ separate seat)
- (w/ separate type amplifier) radio & display receiver assembly
- (w/ separate type amplifier) stereo component amplifier
- 4.0l
- 4wd control ecu
- A/c amplifier
- A/c control assembly
- A15
- A21
- A33
- Access cab
- Access cab w/ speaker (woofer)
- Air bag sensor assembly center
- Backup lamp relay
- Bb (under front passenger's seat)
- Bc (under front passenger's seat)
- Bc2
- Bf (right "c" pillar)
- Bg1
- Bh1
- Bj2
- Blower resistor
- Damper servo motor (air mix)
- Damper servo motor (air vent mode)
- Door control receiver
- Door lock control switch
- Double cab
- E21
- Ed (4.0l) (right rear of engine compt)
- F12
- Front passenger's side door lock assembly
- Hazard warning signal switch assembly
- Ib (center of dash)
- Ic1
- Ic7
- Id (under front of center console)
- Ie (right kick panel)
- Ik3
- Ik4
- Il1
- J16
- J17
- Junction connector
- Junction connector (behind right kick panel)
- Junction connector 16 & 17 (behind right side of dash)
- Junction connector 4 & 5 (behind right side of dash)
- Left outer rear view mirror
- Left seat heater switch
- Noise filter (ignition)
- Occupant classification ecu
- R16
- Right front seat cushion heater assembly
- Right outer rear view mirror
- Right seat heater switch
- S24
- Steering sensor
- Traction control switch
- W/ drl
- W/ outer rear view mirror side turn signal light
Ground Distribution Wiring Diagram (3 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Ground Distribution Wiring Diagram (3 of 4) for Toyota Tacoma X-Runner 2013:
- (12v) acc skt relay
- (12v) front power outlet socket 1 (power point socket assembly)
- (12v) front power outlet socket 2 (power point socket assembly)
- (access cab) left rear lower side door courtesy switch
- (access cab) left rear upper side door courtesy switch
- (double & access cab) map lamp
- (if equipped) towing brake controller
- (if equipped) trailer socket
- (w/ trailer towing)
- A21
- Access cab
- Air bag sensor assembly center
- Ba (under driver's seat)
- Bd (left rear frame rail)
- Bd1
- Be (left "b" pillar)
- Be1
- Be2
- Bf1
- Bi2
- Body ecu
- C13
- Center room lamp
- Center stop lamp
- Combination meter
- Combination switch
- Data link connector
- Differential lock shift actuator assembly
- Double cab
- Driver side j/b (left side of dash)
- Driver's side door lock assembly
- Driver's side front seat inner belt
- E11
- E12
- E13
- Except tmmtx made
- F10
- F11
- Flash relay
- Fuel suction pump & gauge assembly
- H18
- H19
- Ia (left kick panel)
- Ic1
- Ic6
- Ic7
- Inner rear view mirror
- Ip1
- Junction connector 1
- Left front seat cushion heater assembly
- Left license plate lamp
- Left rear combination lamp
- Left vanity light (left visor assembly)
- O11
- O12
- O13
- Outer mirror switch
- P/w relay
- Power window master switch
- Rear differential transfer indicator switch
- Rheostat
- Right license plate lamp
- Right rear combination lamp
- Right vanity light (right visor assembly)
- Tire pressure warning ecu
- Tmmtx made
- To ground ic (diagram 4 of 4)
- Turn signal flasher
- Unlock warning switch
- W/ bench seat
- W/ drl
- W/ vanity light
- Yaw rate sensor
Ground Distribution Wiring Diagram (4 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Ground Distribution Wiring Diagram (4 of 4) for Toyota Tacoma X-Runner 2013:
- (4.0l) engine control module
- (4wd m/t) clutch start cancel switch
- (4wd w/ vacuum booster type) skid control ecu w/ actuator
- (a/t) key interlock solenoid
- (a/t) shift lock control ecu
- (if equipped) 4wd control switch
- (w/ hydraulic booster type) skid control ecu w/ actuator
- (w/ hydraulic booster type) traction control switch
- (w/o door lock control) body ecu
- 2.7l m/t
- 4.0l & 2.7l a/t
- A/f heater relay
- A26
- A27
- A29
- A30
- A31
- A32
- A33
- A34
- A35
- A36
- A37
- A38
- A39
- Air injection control driver
- Air pump
- Batt chg relay
- Brake fluid level warning switch
- C11
- Combination switch
- Curtain airbag cut off switch
- E13
- Ea (right front fender)
- Eb (near battery)
- Efi main relay
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Engine room r/b 2 (left front of engine compt)
- Fog lamp switch
- From unlock warning switch (diagram 3 of 4)
- H10
- H11
- Heater relay
- Ia3
- Ic (center of dash)
- Junction connector 4 & 5 (behind right side of dash)
- Left front fog lamp
- Left headlight assembly
- Option connector (trailer socket)
- Pressure switch
- Right front fog lamp
- Right headlight assembly
- Seat htr relay
- Skid control ecu w/ actuator
- Sta relay
- Tire pressure warning reset switch
- Transponder key ecu
- W/ hydraulic booster type
- W/ vacuum booster type
- Windshield wiper motor
- Wireless door lock buzzer
HEADLIGHTS
Headlights Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Headlights Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (a/t)
- (left side of engine compt) engine room j/b
- (m/t)
- A19
- A20
- A21
- A22
- A33
- A38
- Altb
- Body ecu
- C10
- C11
- C15
- C16
- Combination meter
- Combination switch
- D11
- Dcty
- Dim
- Dim relay
- Dimmer switch
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Drl
- Ea (right front fender)
- Eb (near battery)
- Ecu-b fuse 7.5a
- Ecub
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Exterior lights system
- Flash
- Fr fog fuse 15a
- Gnd
- Ground distribution system
- H-lp lh-hi fuse 10a
- H-lp lh-lo fuse 10a
- H-lp rh-hi fuse 10a
- H-lp rh-lo fuse 10a
- H18
- Head
- Head ind (usa)
- Head relay
- High
- High beam ind
- Hot at all times
- Hot in on or start
- Hrly
- I20
- Ia1
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ij1
- Instrument panel j/b 1 (left side of dash)
- Interior lights system
- J/c 1 (left kick panel)
- J/c j4 & j5 (behind right side of dash)
- J15
- Left headlight assembly
- Light control switch
- Low
- M10
- Off
- Parking brake switch (base of park brake lever)
- Pcty
- Pkb
- Pnk
- Rcty
- Red
- Right headlight assembly
- Starting/charging system
- Tail
- Trly
- Turn signal flasher (w/ daytime running light) (left side of dash)
- Usa
Headlights Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Headlights Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- A23
- A24
- A25
- A33
- A36
- Ea (right front fender)
- Eb (near battery)
- Engine room j/b (left side of engine compt)
- Engine room r/b 2 (left front of engine compt)
- Fog lamp switch
- Fr fog relay
- Ia1
- Ic (center of dash)
- Interior lights system
- J/c j4 & j5 (behind right j5
- Left front fog lamp
- Right front fog lamp
- Side of dash)
HORN
Horn Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Horn Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (left side of dash) driver side j/b
- Body ecu (driver side j/b)
- C10
- Engine room r/b (left front of engine compt)
- High horn (w/ double horn) (2.7l: right front of engine compt) (4.0l: front of engine compt, behind grille)
- Horn
- Horn fuse 10a
- Horn relay
- Horn switch
- Hot at all times
- I22
- Low horn (2.7l: right front of engine compt) (4.0l: above front bumper, behind front grille)
- Spiral cable (behind left side of dash)
INSTRUMENT CLUSTER
Clock Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Clock Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Acc
- Acc fuse 7.5a
- Bb (under front passenger's seat)
- Clock
- Dome fuse 7.5a
- Driver side j/b (left side of dash)
- Engine room r/b (left front of engine compt)
- Hazard warning signal switch assembly
- Hot at all times
- Hot in on or acc
- Hot w/ tail relay energized
- Ill+
- J/c 4 & 5 (behind right side of dash)
- J20
- Tail fuse 10a
Instrument Cluster Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Instrument Cluster Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (4.0l)
- (a/t)
- (except usa)
- (usa)
- 2.7l
- 2wd 4wd
- 4.0l
- 4lo ind
- 4wd control ecu (right side of dash)
- 4wd ind
- A-trac ind
- A/c amplifier (right side of dash)
- A/t
- A/t oil temp ind
- A10
- A11
- A12
- A13
- A14
- A15
- A16
- A17
- A18
- A19
- A20
- A21
- A22
- A23
- A24
- A25
- A26
- A27
- A28
- A29
- A30
- A31
- A32
- A33
- A34
- A35
- A36
- A37
- A38
- A39
- A40
- Abs ind
- Auto lsd ind
- B10
- B11
- B12
- B13
- B14
- B15
- B16
- B20
- Bat
- Brake ind
- Buzzer
- C10
- C12
- C16
- Canada
- Charge ind
- Combination meter
- Computer data lines system
- Cpu
- Cruise ind
- Door ind
- Downhill assist control ind
- Driver side j/b (left side of dash)
- Driver's seat belt ind
- E13
- E22
- Ecu-b fuse 7.5a
- Engine control module (behind right side of dash)
- Engine controls system
- Engine oil pressure switch (4.0l: center front of engine) (2.7l: right front of engine)
- Engine room r/b (left front of engine compt)
- Exterior lights system
- F10
- F12
- F14
- Fuel gauge
- Fuel ind
- Fuel suction pump & gauge assembly (fuel tank)
- Gauge fuse 7.5a
- Head ind
- Headlights system
- High beam ind
- Hot at all times
- Hot in on or start
- Ia1
- Id2
- Ih1
- Il3
- Im1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c 1 (left kick panel)
- K13
- Lcd (odo meter)
- Left turn ind
- M/t
- Maint reqd ind
- Malfunction indicator lamp
- Oil pressure ind
- Pnk
- Rear diff lock ind
- Red
- Right turn ind
- Rsca off ind
- S23
- Slip ind
- Spd
- Speedometer
- Srs ind
- Starting/charging system
- Steering sensor (steering wheel)
- Stereo component amplifier (near right "c" pillar)
- Tachometer
- Tail ind
- Temperature gauge
- Tire pressure ind
- Tire pressure warning ecu (center of dash)
- Trac off ind
- Transmissions system
- Usa
- Voltage inverter (left rear of vehicle compt)
- Vsc off ind
- W/ built in type amplifier
- W/ separate type amplifier
- Warning systems
Instrument Cluster Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Instrument Cluster Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- (a/t)
- (m/t)
- Access cab
- Acty
- B16
- Be (left "b" pillar)
- Bf (right "c" pillar)
- Bf1
- Bg1
- Body ecu
- Brake fluid level warning switch (brake fluid reservoir)
- D11
- Dcty
- Double cab
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- Eb (near battery)
- Front passenger's side door courtesy switch
- Ia1
- Ii1
- Il1
- Instrument panel j/b 1 (left side of dash)
- J15
- Lbl
- Left rear door courtesy switch
- Left rear lower side door courtesy switch
- Left rear upper side door courtesy switch
- Parking brake switch (base of park brake lever)
- Pcty
- Pkb
- R15
- R17
- Radio & display receiver assembly
- Rcty
- Right rear door courtesy switch
- Right rear lower side door courtesy switch
- Right rear upper side door courtesy switch
- Skid control ecu w/ actuator (hydraulic booster type: left rear of engine compt) (vacuum booster type: right rear of engine compt)
- Sp1
- Spd
- W/ built in type amplifier
- W/ hydraulic booster type
- W/ separate type amplifier
- W/ vacuum booster type
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Courtesy Lamps Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (behind right kick panel) j/c 13
- (behind right kick panel) j/c 14
- Access cab
- Acty
- Altb
- Ba (under driver's seat)
- Bd (left rear frame rail)
- Be (left "b" pillar)
- Bf1
- Bg1
- Body ecu (driver side j/b)
- C16
- Dcty
- Dome fuse 7.5a
- Double cab
- Dr lck fuse 20a
- Driver side door lock assembly
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- E11
- E12
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b 1 (left front of engine compt)
- Except tmmtx made
- F10
- F11
- Front passenger's side door courtesy switch
- Front passenger's side door lock assembly
- Gauge fuse 7.5a
- Gnd
- Ground distribution system
- H18
- Hot at all times
- Hot in on or start
- Ic (center of dash)
- Ic6
- Ig1 2 fuse 10a
- Ii1
- Ik3
- Il1
- Ile
- Ip1
- J/c 1 (left kick panel)
- J/c j4 & j5 (behind right side of dash)
- J15
- K13
- Left rear door courtesy switch
- Lswd
- Lswp
- O11
- O12
- Pcty
- Pnk
- Rcty
- Red
- Right rear door courtesy switch
- Switch detection
- Tmmtx made
- W/ door lock control
- W/o door lock control
Courtesy Lamps Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Courtesy Lamps Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- Be (left "b" pillar)
- Bf (right "c" pillar)
- Center room lamp
- Combination meter
- Door
- Door ind
- Except tmmtx made w/ vanity lamp
- Except tmmtx made w/o vanity lamp
- Ip1
- Lamp
- Left rear door lower side courtesy switch
- Left rear door upper side courtesy switch
- Left vanity light (left visor assembly)
- Map lamp (except regular cab)
- Off
- Pnk
- Red
- Right rear door lower side courtesy switch
- Right rear door upper side courtesy switch
- Right vanity light (right visor assembly)
- Tmmtx made
- W/ vanity
- W/o vanity lamp
Instrument Illumination Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Instrument Illumination Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (behind left side of dash) j/c 2
- (under front of center console) id
- A/c control assembly
- A/t shift lever illumi- nation
- A33
- Body ecu
- C11
- C13
- C14
- Combination meter
- Combination switch
- Cpu
- Curtain air bag cut off switch (4wd)
- Differ- ential lock switch
- Downhill assist control switch (if equipped)
- Driver side j/b (left side of dash)
- Drl (usa) off (except usa)
- Engine room r/b 1 (left front of engine compt)
- Except regular cab
- Fog lamp switch
- Gnd
- Ground distribution system
- Hazard warning signal switch assembly
- Head
- Hot at all times
- Hot in on or start
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ij1
- Ill+
- Ill-
- Instrument panel j/b 1 (left side of dash)
- J/b fuse 50a
- J/c 1 (left kick panel)
- J/c 3 (behind left side of dash)
- J/c j17 & j16 (behind right side of dash)
- J/c j4 & j5 (behind right side of dash)
- J16
- J17
- J19
- Left seat heater switch (if equi- pped)
- Light control switch
- R15
- R16
- Radio & display receiver assembly
- Regular cab
- Rheostat
- Right seat heater switch (if equi- pped)
- Spiral cable (behind left side of dash)
- Steering pad switch
- Swg
- Tail
- Tail fuse 10a
- Tail relay
- Traction control switch
- Traction control switch (hydraulic booster type)
- Trly
- W/ built-in type amplifier
- W/ seat heater
- W/ separate type amplifier
NAVIGATION
Navigation Wiring Diagram (1 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Navigation Wiring Diagram (1 of 4) for Toyota Tacoma X-Runner 2013:
- Acc
- Agnd
- Antenna
- Avc+
- Avc-
- B16
- E15
- E16
- Extension module (right side of dash)
- Gps antenna
- Hsyn
- Instrument panel j/b 1 (left side of dash)
- Mic+
- Mic-
- Mute
- Nca
- Parking brake switch (base of park brake lever)
- Pkb
- Pnk
- R17
- R19
- R20
- Radio & display receiver assembly
- Red
- Sdars antenna
- Shd1
- Shd2
- Shd3
- Spd
- V-b
- V-g
- V-r
- Vol+
- Vol-
- Vshd
- Vsyn
Navigation Wiring Diagram (2 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Navigation Wiring Diagram (2 of 4) for Toyota Tacoma X-Runner 2013:
- A10
- B10
- C16
- Combination meter
- Cpu
- Cruise control system
- Driver side j/b (left side of dash)
- E13
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- Hot at all times
- Ia1
- Ia4
- Il3
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Iq1
- J/c 1 (left kick panel)
- K13
- Left steering pad switch
- Mode
- Nca
- Off hook
- On hook
- Radio 1 fuse 10a
- Radio 2 fuse 30a
- Red
- Right steering pad switch
- Seek+
- Seek-
- Spiral cable (behind left side of dash)
- Stereo jack adapter
- Voice
- Vol+
- Vol-
Navigation Wiring Diagram (3 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Navigation Wiring Diagram (3 of 4) for Toyota Tacoma X-Runner 2013:
- (under front of center console) id
- +b1
- Acc1
- Adpg
- Agnd
- Except tmmtx made
- Gnd1
- Ic4
- Ik4
- Il3
- Ill+
- Ill-
- In1
- In2
- Interior lights system
- Ip2
- Ivo+
- Ivo-
- Left front door speaker
- Macc
- Mco+
- Mco-
- Min+
- Min-
- Mut1
- Nca
- Pnk
- R15
- R16
- Radio & display receiver assembly
- Red
- Right front door speaker
- Sgnd
- Sld
- Sld1
- Sns2
- Spd
- Sw1
- Sw2
- Swg
- Telephone microphone assembly
- Tmmtx made
- Tx2+
- Tx2-
- Va-
- Val+
- Var+
Navigation Wiring Diagram (4 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Navigation Wiring Diagram (4 of 4) for Toyota Tacoma X-Runner 2013:
- +b2
- Acc
- Acc fuse 7.5a
- Ba1
- Bb (under front passenger's seat)
- Bb1
- Driver side j/b (left side of dash)
- Fl+
- Fl-
- Fr+
- Fr-
- Gauge fuse 7.5a
- Gnd
- Hot in on or acc
- Hot in on or start
- Ic4
- Ie2
- Ig1 fuse 10a
- Ik4
- Il3
- Il4
- Instrument panel j/b 2 (right side of dash)
- Int+
- Int-
- J/c 17 (behind right side of dash)
- J/c 4 & 5 (behind right side of dash)
- Left rear door speaker
- Left tweeter speaker
- Mute
- Nca
- Pnk
- Red
- Right rear door speaker
- Right tweeter speaker
- Rl+
- Rl-
- Rr+
- Rr-
- S23
- S24
- S31
- Sgnd
- Spd
- Stereo component amplifier (near right "c" pillar)
- Twl+
- Twl-
- Twr+
- Twr-
- Tx+
- Tx-
- Wf+
- Wf-
- Wfl+
- Wfl-
- Wfr+
- Wfr-
- Woofer speaker
Rear View Camera Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Rear View Camera Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (left side of dash) driver side j/b
- A/t
- Air conditioning system
- Backup lamp switch (right side of transmission)
- Bd (left rear frame rail)
- Bn1
- C16
- Cb+
- Cgnd
- Cv+
- Cv-
- Driver side j/b (left side of dash)
- E13
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- Except tmmtx made
- H13
- Hot at all times
- Hot in on or start
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ih1
- In1
- In2
- Inner rear view mirror
- Instrument panel j/b 2 (right side of dash)
- Io1
- Io2
- Ip1
- M/t
- Nca
- O13
- Park/ neutral position switch (transmission)
- Pnk
- Red
- Rev
- Television camera (tailgate)
- Temp
- Tmmtx made
POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Power Distribution Wiring Diagram (1 of 3) for Toyota Tacoma X-Runner 2013:
- (left front of engine compt) engine room r/b
- (not used)
- (w/o trailer towing) (w/ trailer towing)
- A/c amplifier, combination meter, transponder key ecu, steering sensor occupant classification ecu (w/ separate seat), door control receiver, body ecu & inner rear view mirror
- A/f heater relay
- A/f htr fuse 15a
- A/f htr relay & ai valve relay
- A/pump fuse 50a
- Abs 1 fuse 50a
- Abs 2 fuse 30a
- Air injection control driver
- Air pump htr fuse 10a
- Alt fuse 120a 140a
- Alt-s fuse 7.5a
- Am1 fuse 50a
- Am2 fuse 30a
- Batt chg fuse 30a
- Batt chg relay
- Battery
- Data link connector
- Dome fuse 7.5a
- Ecu-b fuse 7.5a
- Efi main fuse 20a
- Efi main relay & engine control module
- Engine control module
- Engine room j/b (left side of engine compt)
- Etcs fuse 10a
- Fr fog fuse 15a
- Fr fog relay
- Generator
- Head relay
- Heater fuse 50a
- Heater relay
- Horn fuse 10a
- Horn relay
- Inv fuse 100a
- J/b fuse 50a
- Left vanity light (left visor assembly) (if equipped) right vanity light (right visor assembly) (if equipped) center room lamp, map lamp & hazard warning signal switch assembly
- Obd fuse 7.5a
- Radio & display receiver assembly
- Radio 1 fuse 20a
- Radio 2 fuse 30a
- Red
- S/htr 1 fuse 50a
- S/htr 2 fuse 30a
- Seat htr relay
- Short pin
- Skid control ecu w/ actuator
- Starter
- Stereo component amplifier (w/ separate type amplifier) speaker (woofer) (w/ built-in type amplifier & access cab)
- Stop fuse 10a
- Stop lamp switch & stop lamp control relay (w/ hydraulic booster type, vacuum booster type w/ trailer towing)
- To driver side j/b (diagram 3 of 3)
- To engine room r/b 2 (diagram 3 of 3)
- To ignition switch (diagram 2 of 3)
- Towing brake controller
- Towing brk fuse 30a
- Towing fuse 30a
- Towing tail fuse 30a
- Towing tail relay
- Trn-haz fuse 15a
- Turn signal flasher (w/ drl & trailer towing)
- Turn signal flasher (w/ drl)
- W/ hydraulic booster type
Power Distribution Wiring Diagram (2 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Power Distribution Wiring Diagram (2 of 3) for Toyota Tacoma X-Runner 2013:
- (2.7l)
- (right side of dash) instrument panel j/b 2
- 2.7l a/t
- 4.0l a/t
- 4wd control ecu
- 4wd fuse 20a
- 4wd m/t
- A/t
- A11
- Acc
- Acc fuse 7.5a
- Am1
- Am2
- B10
- B11
- B18
- Backup lamp relay
- Backup lamp switch (m/t) & park/neutral position switch (a/t)
- Bkup lp fuse 10a
- Body ecu
- C/opn relay
- C13
- C14
- C17
- Center air bag sensor assembly
- Clutch start cancel switch (4wd)
- Clutch start diode (m/t)
- Combination meter
- Combination switch
- Driver side j/b (left side of dash)
- Engine control module
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Except tmmtx made
- From engine room r/b (diagram 1 of 3)
- Fuel injectors
- Gauge fuse 7.5a
- H11
- H13
- H15
- H17
- H20
- Hazard warning signal switch assembly
- I13
- I15
- Ig1
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ig2
- Ign fuse 15a
- Ignition coils & noise filter (ignition)
- Ignition switch
- Inner rear view mirror
- J10
- J16
- J20
- Left seat heater sw, right seat heater sw, shift lock control ecu, hazard warning signal switch assembly, generator, air mix damper servo motor, a/c control assembly, air vent damper servo motor, a/c amplifier, stop lp ctrl relay & (w/ hydraulic booster, vacuum booster type & trailer towing) radio & display receiver assembly
- Lock
- M/t
- Occupant classification ecu
- Off
- Outer mirror switch
- Park/ neutral position switch (a/t)
- Pnk
- Shift lock control ecu
- Skid control ecu w/ actuator (w/ hydraulic booster type)
- Skid control ecu w/ actuator (w/o rear differential lock & w/ vacuum booster type)
- St1
- St2
- Sta fuse 7.5a
- Sta relay
- Start
- Stereo component amplifier (w/ separate type amplifier), speaker (woofer) & (w/ built-in type amplifier access cab) radio & display receiver assembly
- Stop lamp switch
- Tmmtx made
- To acc skt relay (diagram 3 of 3)
- To instrument panel j/b 1 (diagram 3 of 3)
- To voltage inverter (diagram 3 of 3)
- Transponder key ecu
- Turn signal flasher (w/ drl & trailer towing)
- Windshield washer motor
- Windshield wiper motor
- Wip fuse 30a
- Wsh fuse 10a
Power Distribution Wiring Diagram (3 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Power Distribution Wiring Diagram (3 of 3) for Toyota Tacoma X-Runner 2013:
- (2.7l)
- (4.0l)
- (a/t)
- (m/t)
- 400w
- A11
- A12
- A13
- Ac skt relay
- Ac1
- Ac2
- Acc skt relay
- Acc1
- Acc2
- Altb
- B15
- Batt chg relay (w/ trailer towing)
- Bc (under front passenger's seat)
- Bc1
- Bc2
- Body ecu
- C11
- C13
- C14
- Cccl
- Clutch start cancel switch (4wd m/t)
- Combination meter, engine control module, (2.7l) hazard warning signal switch assembly & tail diode (4.0l)
- Cruise control clutch switch (m/t)
- Cruise control system
- D10
- Differential lock switch
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- E13
- E21
- Ed1
- Ed2
- Els2
- Els3
- Engine control module
- Engine room r/b 2 (left front of engine compt)
- From acc fuse (diagram 2 of 3)
- From driver side j/b (diagram 2 of 3)
- From engine room j/b (diagram 1 of 3)
- From engine room r/b (diagram 1 of 3)
- From instrument panel j/b 2 (diagram 2 of 3)
- Front power outlet socket 2 power point socket assembly (12v)
- Front power point socket 1 power point socket assembly (12v)
- Generator (4.0l)
- Gnd
- H18
- Heater relay
- Ia4
- Im1
- Ind
- Instrument cluster system
- Instrument panel j/b 1 (left side of dash)
- J19
- Junction connector j1 (left kick panel)
- K11
- Left headlight assembly
- Left rear combination lamp, right rear combination lamp, left license plate lamp & right license plate lamp
- Left seat heater switch, right seat heater switch, spiral cable, rheostat, fog lamp switch, traction control switch, downhill assist control switch, (if equipped) differential lock switch, towing brake connector & curtain air bag cutoff switch (4wd)
- Mg clt relay
- Nsw
- Out
- P/t
- P/w relay
- Pgnd
- Power ind+ outlet main switch (120v) ind-
- Pwr outlet fuse 15a
- Rear power point socket assembly (120v)
- Red
- Redr
- Rheostat
- Right headlight assembly
- Seat heater relay
- Skid control ecu w/ actuator
- Spd
- Steering sensor
- Tail fuse 10a
- Tail relay
- Tire pressure warning ecu
- Towing tail relay
- Trly
- Voltage inverter (under front passenger's seat)
- W/ trailer towing
- W/o trailer towing
- Yaw rate sensor
POWER DOOR LOCKS
Power Door Locks Wiring Diagram, with Keyless Entry (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Power Door Locks Wiring Diagram, with Keyless Entry (1 of 2) for Toyota Tacoma X-Runner 2013:
- Access cab
- Act+
- Act-
- Actd
- Altb
- Ba1
- Bb1
- Body ecu
- Buzzer
- Bzr
- Detection switch
- Double cab
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Driver's side door lock assembly
- Eb (near battery)
- Front passenger's side door lock assembly
- Gnd
- H18
- H22
- H23
- H24
- Hot at all times
- Hot in run or start
- Ia1
- Ic (center of dash)
- Ic1
- Ic6
- Ig1 2 fuse 10a
- Ik3
- Ik4
- Il2
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- K10
- Ksw
- Left rear door lock assembly (double cab)
- Lswd
- Lswp
- Red
- Right rear door lock assembly (double cab)
- Wireless door lock buzzer (left front of engine compt)
Power Door Locks Wiring Diagram, with Keyless Entry (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Power Door Locks Wiring Diagram, with Keyless Entry (2 of 2) for Toyota Tacoma X-Runner 2013:
- Access cab
- Be (left "b" pillar)
- Bf (right "c" pillar)
- Bf1
- Bg1
- Body ecu
- C10
- C16
- Dcty
- Door control receiver (right side of dash)
- Double cab
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- Exterior lights system
- Front passenger's side door courtesy switch
- Gnd
- Haz
- Horn
- Horn relay
- Hot at all times
- I16
- Il1
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J15
- Left rear door courtesy switch
- Left rear lower side door courtesy switch
- Left rear upper side door courtesy switch
- Pcty
- Prg
- Rcty
- Rda
- Red
- Right rear door courtesy switch
- Right rear lower side door courtesy switch
- Right rear upper side door courtesy switch
- Trly
- Turn signal flasher (w/ trailer towing) (left side of dash)
- Unlock warning switch
Power Door Locks Wiring Diagram, without Keyless Entry for Toyota Tacoma X-Runner 2013
List of elements for Power Door Locks Wiring Diagram, without Keyless Entry for Toyota Tacoma X-Runner 2013:
- Access cab
- Act+
- Act-
- Actd
- Altb
- Ba (under driver's seat)
- Ba1
- Bb1
- Bench seat
- Bi2
- Body ecu
- C16
- Dbkl
- Detection switch
- Door lock control switch
- Double cab
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Driver's side door lock assembly
- Driver's side front seat inner belt
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- Front passenger's side door lock assembly
- Gnd
- H18
- H22
- H23
- H24
- Hot at all times
- Hot in run or start
- I14
- I17
- I18
- I19
- Ic (center of dash)
- Ic1
- Ic6
- Ic7
- Ig1 2 fuse 10a
- Ik3
- Ik4
- Il2
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J13
- K10
- Key unlock
- Ksw
- Left rear door lock assembly (double cab)
- Lock
- Lswd
- Lswp
- Pnk
- Power window master switch
- Red
- Right rear door lock assembly (double cab)
- Ul1
- Ul2
- Ul3
- Unlock
- Unlock warning switch
POWER MIRRORS
Electrochromic Mirror Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Electrochromic Mirror Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (left side of dash) driver side j/b
- A/t
- Air conditioning system
- Backup lamp switch (right side of transmission)
- Bd (left rear frame rail)
- Bn1
- C16
- Cb+
- Cgnd
- Cv+
- Cv-
- Driver side j/b (left side of dash)
- E13
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- Except tmmtx made
- H13
- Hot at all times
- Hot in on or start
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Ih1
- In1
- In2
- Inner rear view mirror
- Instrument panel j/b 2 (right side of dash)
- Io1
- Io2
- Ip1
- M/t
- Nca
- O13
- Park/ neutral position switch (transmission)
- Pnk
- Red
- Rev
- Television camera (tailgate)
- Temp
- Tmmtx made
Power Mirrors Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Power Mirrors Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Acc fuse 7.5a
- Down
- Driver side j/b (left side of dash)
- Exterior lights
- F11
- Hot in run or acc
- Ic6
- Ik3
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J16
- Left
- Left outer rear view mirror
- Mlh
- Mlv
- Mrh
- Mrv
- Operation switch
- Outer mirror switch
- Pnk
- Right
- Right outer rear view mirror
- Select switch
- System
- Turn
POWER SEATS
Power Seats Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Power Seats Wiring Diagram for Toyota Tacoma X-Runner 2013:
- A32
- A33
- Ba (under driver's seat)
- Bb (under front passenger's seat)
- C13
- C14
- Driver side j/b (left side of dash)
- Ea (right front fender)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Engine room r/b 2 (left front of engine compt)
- Hot at all times
- Hot in on or start
- Ia4
- Ie2
- Ig1 2 fuse 10a
- Ig1 fuse 10a
- Il1
- Ill+
- Ill-
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c (behind right kick panel)
- J/c 16 & 17 (behind right side of dash)
- J/c 16 & 17 (behind right side of dash) j16
- J/c 5 (behind right side of dash)
- J16
- J17
- Left front seat cushion heater assembly
- Left seat heater switch
- Pnk
- Right front seat cushion heater assembly
- Right seat heater switch
- S/htr 2 fuse 30a
- Seat back heater
- Seat cushion heater
- Seat heater control
- Seat htr relay
- Thl
- Thr
POWER WINDOWS
Power Windows Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Power Windows Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Access cab
- Altb
- Auto down
- Ba1
- Bb1
- Bf1
- Bg1
- Body ecu
- C16
- D fr p/w fuse 30a
- D rr p/w fuse 20a
- Dcty
- Door locks system
- Double cab
- Down
- Dr lck fuse 20a
- Driver side j/b (left side of dash)
- Driver's side door courtesy switch
- Ecu-b fuse 7.5a
- Ecub
- Engine room r/b (left front of engine compt)
- F17
- Front passenger
- Front passenger's side door courtesy switch
- Front passenger's side power window switch
- Gnd
- H14
- H16
- H18
- Hot at all times
- Hot in run or start
- Ic1
- Ic4
- Ic7
- Ie2
- Ig1 2 fuse 10a
- Ik4
- Il1
- Il2
- J/b fuse 50a
- J/c 1 (left kick panel)
- Left front power window regulator motor
- Left rear
- Left rear power window regulator motor (double cab)
- Left rear power window switch (double cab)
- Lock
- P fr p/w fuse 20a
- P rr p/w fuse 20a
- P/w relay
- Pcty
- Power window master switch
- Pws
- Red
- Right front power window regulator motor
- Right rear
- Right rear power window regulator motor (double cab)
- Right rear power window switch (double cab)
- Unlock
- Window lock switch
RADIO
Radio Wiring Diagram, with Navigation (1 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, with Navigation (1 of 4) for Toyota Tacoma X-Runner 2013:
- Acc
- Agnd
- Antenna
- Avc+
- Avc-
- B16
- E15
- E16
- Extension module (right side of dash)
- Gps antenna
- Hsyn
- Instrument panel j/b 1 (left side of dash)
- Mic+
- Mic-
- Mute
- Nca
- Parking brake switch (base of park brake lever)
- Pkb
- Pnk
- R17
- R19
- R20
- Radio & display receiver assembly
- Red
- Sdars antenna
- Shd1
- Shd2
- Shd3
- Spd
- V-b
- V-g
- V-r
- Vol+
- Vol-
- Vshd
- Vsyn
Radio Wiring Diagram, with Navigation (2 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, with Navigation (2 of 4) for Toyota Tacoma X-Runner 2013:
- A10
- B10
- C16
- Combination meter
- Cpu
- Cruise control system
- Driver side j/b (left side of dash)
- E13
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- Hot at all times
- Ia1
- Ia4
- Il3
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Iq1
- J/c 1 (left kick panel)
- K13
- Left steering pad switch
- Mode
- Nca
- Off hook
- On hook
- Radio 1 fuse 10a
- Radio 2 fuse 30a
- Red
- Right steering pad switch
- Seek+
- Seek-
- Spiral cable (behind left side of dash)
- Stereo jack adapter
- Voice
- Vol+
- Vol-
Radio Wiring Diagram, with Navigation (3 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, with Navigation (3 of 4) for Toyota Tacoma X-Runner 2013:
- (under front of center console) id
- +b1
- Acc1
- Adpg
- Agnd
- Except tmmtx made
- Gnd1
- Ic4
- Ik4
- Il3
- Ill+
- Ill-
- In1
- In2
- Interior lights system
- Ip2
- Ivo+
- Ivo-
- Left front door speaker
- Macc
- Mco+
- Mco-
- Min+
- Min-
- Mut1
- Nca
- Pnk
- R15
- R16
- Radio & display receiver assembly
- Red
- Right front door speaker
- Sgnd
- Sld
- Sld1
- Sns2
- Spd
- Sw1
- Sw2
- Swg
- Telephone microphone assembly
- Tmmtx made
- Tx2+
- Tx2-
- Va-
- Val+
- Var+
Radio Wiring Diagram, with Navigation (4 of 4) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, with Navigation (4 of 4) for Toyota Tacoma X-Runner 2013:
- +b2
- Acc
- Acc fuse 7.5a
- Ba1
- Bb (under front passenger's seat)
- Bb1
- Driver side j/b (left side of dash)
- Fl+
- Fl-
- Fr+
- Fr-
- Gauge fuse 7.5a
- Gnd
- Hot in on or acc
- Hot in on or start
- Ic4
- Ie2
- Ig1 fuse 10a
- Ik4
- Il3
- Il4
- Instrument panel j/b 2 (right side of dash)
- Int+
- Int-
- J/c 17 (behind right side of dash)
- J/c 4 & 5 (behind right side of dash)
- Left rear door speaker
- Left tweeter speaker
- Mute
- Nca
- Pnk
- Red
- Right rear door speaker
- Right tweeter speaker
- Rl+
- Rl-
- Rr+
- Rr-
- S23
- S24
- S31
- Sgnd
- Spd
- Stereo component amplifier (near right "c" pillar)
- Twl+
- Twl-
- Twr+
- Twr-
- Tx+
- Tx-
- Wf+
- Wf-
- Wfl+
- Wfl-
- Wfr+
- Wfr-
- Woofer speaker
Radio Wiring Diagram, without Navigation (1 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, without Navigation (1 of 3) for Toyota Tacoma X-Runner 2013:
- Acc
- Acc fuse 7.5a
- Access cab
- Antenna
- Ba1
- Bb (under front passenger's seat)
- Bb1
- Double cab
- Driver side j/b (left side of dash)
- Engine room r/b (left front of engine compt)
- Fl+
- Fl-
- Fr+
- Fr-
- Gnd
- Hot at all times
- Hot in on or acc
- Ia1
- Ia4
- Id (under front of center console)
- Ie2
- Il2
- Il4
- Ill+
- Ill-
- Interior lights system
- J/c 4 & 5 (behind right side of dash)
- Left rear door speaker (double cab)
- Nca
- Pnk
- Radio & display receiver assembly
- Radio 1 fuse 20a
- Radio 2 fuse 30a
- Red
- Regular cab & double cab
- Right rear door speaker (double cab)
- Rl+
- Rl-
- Rr+
- Rr-
- Speaker (woofer) (access cab w/ speaker woofer)
Radio Wiring Diagram, without Navigation (2 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, without Navigation (2 of 3) for Toyota Tacoma X-Runner 2013:
- Access cab
- C16
- Combination meter
- Cpu
- Cruise control system
- Double cab
- Double cab & access cab
- Driver side j/b (left side of dash)
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- Gauge fuse 7.5a
- Hot at all times
- Hot in on or start
- Ic1
- Ic2
- Ic4
- Ik2
- Ik4
- In2
- Instrument panel j/b 2 (right side of dash)
- Ip2
- J/c 1 (left kick panel)
- J/c 16 & 17 (access cab) (behind right side of dash)
- J16
- J17
- K13
- Left front door speaker
- Left roof speaker assembly
- Left tweeter speaker
- Li+
- Li-
- Lo+
- Lo-
- Pnk
- Radio setting condenser (right side of dash)
- Red
- Regular cab
- Ri+
- Ri-
- Right front door speaker
- Right roof speaker assembly
- Right tweeter speaker
- Ro+
- Ro-
Radio Wiring Diagram, without Navigation (3 of 3) for Toyota Tacoma X-Runner 2013
List of elements for Radio Wiring Diagram, without Navigation (3 of 3) for Toyota Tacoma X-Runner 2013:
- Adpg
- Agnd
- Au1
- Au2
- Double cab
- Driver side j/b (left side of dash)
- Eau
- Except tmmtx made
- Hot in on or start
- Ig1 fuse 10a
- In1
- In2
- Instrument panel j/b 2 (right side of dash)
- Ip2
- Iq1
- J/c 17 (behind right side of dash)
- Left steering pad switch
- Macc
- Mco+
- Mco-
- Min+
- Min-
- Mode
- Nca
- Off hook
- On hook
- Pnk
- R15
- R22
- Radio & display receiver assembly
- Red
- Regular cab & access cab
- Right steering pad switch
- Seek+
- Seek-
- Sgnd
- Shield
- Sns2
- Spd
- Spiral cable (w/ audio switch in steering wheel) (behind left side of dash)
- Stereo jack adapter 1
- Sw1
- Sw2
- Swg
- Telephone microphone assembly
- Tmmtx made
- Va-
- Val+
- Var+
- Vol+
- Vol-
SHIFT INTERLOCK
Shift Interlock Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Shift Interlock Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (left rear of engine compt) skid control ecu w/ actuator (hydraulic booster type)
- 2.7l
- 4.0l
- Acc
- Acc fuse 7.5a
- At2
- At3
- Atd
- Atl
- B13
- Canh
- Canl
- Computer data lines system
- Driver side j/b (left side of dash)
- E10
- E14
- E19
- E22
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- H13
- Hot at all times
- Hot in run or acc
- Hot in run or start
- Hydraulic booster type
- Ia3
- Ic (center of dash)
- Ig1 fuse 10a
- Ih1
- Ih2
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c j4 & j5 (behind right side of dash)
- J10
- Junction connector j5 (behind right side of dash)
- Key interlock solenoid (left side of dash)
- Kls+
- Nssd
- Nssl
- Park/neutral position switch (transmission)
- Pnk
- Shift lock control ecu (under center console)
- Shift lock solenoid
- Sls+
- Sls-
- Stop fuse 10a
- Stop lamp switch (bracket, above brake pedal)
- Stop lp ctrl relay
- Stp
- Stp2
- Stpo
- System
- Transmissions
- Vacuum booster type w/ trailer towing
- W/ hydraulic booster type & vacuum booster type w/ trailer towing
- W/ vacuum booster type w/o trailer towing
STARTING/CHARGING
2.7L
2.7L, Charging Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Charging Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) engine control module
- A15
- Alt
- Alt fuse 120a
- Alt-s fuse 7.5a
- B12
- Battery
- Body ecu (driver side j/b)
- Charge ind
- Combination meter
- Driver side j/b (left side of dash)
- E17
- Ea1
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Gauge fuse 7.5a
- Generator
- Hot in run or start
- Ig1 fuse 10a
- Ih1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Pnk
- Starting circuit
2.7L, Starting Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Starting Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (2.7l)
- (4.0l)
- 2.7l a/t
- 4.0l a/t
- 4wd m/t
- A/t
- A11
- A26
- A33
- Acc
- Alt fuse 120a
- Am1
- Am1 fuse 50a
- Am2
- Am2 fuse 30a
- B15
- B18
- Battery
- C13
- C14
- Clutch start cancel switch (4wd m/t) (bracket above clutch pedal)
- Clutch start diode (m/t) (left side of dash)
- Clutch start switch (m/t) (bracket above clutch pedal)
- D16
- Driver side j/b (left side of dash)
- E10
- E14
- E22
- Ea (right front fender)
- Eb1
- Engine control module (behind right side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Hot in run or start
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ignition switch
- Ih1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c j4 & j5 (behind right side of dash)
- Lock
- Nsw
- On off
- Park/ neutral position switch (trans- mission)
- Solid state
- Sta
- Sta fuse 7.5a
- Sta relay
- Start st1
- Start st2
- Starter
4.0L
4.0L, Charging Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Charging Wiring Diagram for Toyota Tacoma X-Runner 2013:
- Alt fuse 120a
- Alt-s fuse 7.5a
- B12
- Battery
- Body ecu (driver side j/b)
- C13
- C14
- Charge ind
- Combination meter
- Driver side j/b (left side of dash)
- Eb1
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Gauge fuse 7.5a
- Generator
- Hot in run or start
- Ig1 2 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Starting circuit
4.0L, Starting Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Starting Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (2.7l)
- (4.0l)
- 2.7l a/t
- 4.0l a/t
- 4wd m/t
- A/t
- A11
- A26
- A33
- Acc
- Alt fuse 120a
- Am1
- Am1 fuse 50a
- Am2
- Am2 fuse 30a
- B15
- B18
- Battery
- C13
- C14
- Clutch start cancel switch (4wd m/t) (bracket above clutch pedal)
- Clutch start diode (m/t) (left side of dash)
- Clutch start switch (m/t) (bracket above clutch pedal)
- D16
- Driver side j/b (left side of dash)
- E10
- E14
- E22
- Ea (right front fender)
- Eb1
- Engine control module (behind right side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Hot in run or start
- Ic (center of dash)
- Ig1 2 fuse 10a
- Ignition switch
- Ih1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c j4 & j5 (behind right side of dash)
- Lock
- Nsw
- On off
- Park/ neutral position switch (trans- mission)
- Solid state
- Sta
- Sta fuse 7.5a
- Sta relay
- Start st1
- Start st2
- Starter
SUPPLEMENTAL RESTRAINTS
Supplemental Restraints Wiring Diagram, Bench Seat (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Supplemental Restraints Wiring Diagram, Bench Seat (1 of 2) for Toyota Tacoma X-Runner 2013:
- (base of right "b" pillar) right front side air bag sensor
- (behind right side of dash) air bag squib (front passenger's air bag assembly)
- (right "b" pillar) right curtain shield air bag squib
- (under steering wheel pad) air bag squib (steering wheel pad)
- +sl
- +sr
- -sl
- -sr
- A21
- A22
- A23
- A24
- A25
- Access cab
- Bbd+
- Bbd-
- Bbl+
- Bbl-
- Bbp+
- Bbp-
- Bbr+
- Bbr-
- Bcl+
- Bcl-
- Bcr+
- Bcr-
- Bf2
- Bg2
- Bk1
- Canh
- Canl
- Center air bag sensor assembly (center of dash)
- Computer data lines system
- D2+
- D2-
- Dbe+
- Dbe-
- Double & access cab
- Driver's side front seat inner belt
- Dsp+
- Dsp-
- Fsp+
- Fsp-
- Gsw3
- Ib (center of dash)
- Icd+
- Icd-
- Icp+
- Icp-
- Ig1
- Ig2
- Left curtain shield air bag squib (left "b" pillar)
- Left front seat outer belt
- Left front side air bag sensor (base of left "b" pillar)
- Left rear side air bag sensor (double & access cab) (base of left "c" pillar)
- Left side air bag squib
- P-ab
- P2+
- P2-
- Paon
- Pd+
- Pd-
- Pnk
- Pp+
- Pp-
- Pre- tensioner
- Pretensioner
- Red
- Regular cab
- Right front seat outer belt
- Right rear side air bag sensor (double & access cab) (base of right "c" pillar)
- Right seat position air bag sensor
- Right side air bag squib
- Rmil
- Rmsw
- Sfd+
- Sfd-
- Sfl+
- Sfl-
- Sfp+
- Sfp-
- Sfr+
- Sfr-
- Sil
- Spiral cable
Supplemental Restraints Wiring Diagram, Bench Seat (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Supplemental Restraints Wiring Diagram, Bench Seat (2 of 2) for Toyota Tacoma X-Runner 2013:
- (below left center of dash) data link connector 3
- +sl
- +sr
- -sl
- -sr
- Access cab
- Air
- Air bag on/off ind
- B17
- Be (left "b" pillar)
- Bf1
- Bgnd
- Bj2
- Bsw
- Combination meter
- Computer data lines system
- Cpu
- Curtain air bag cutoff switch (4wd)
- Dia
- Driver side j/b (left side of dash)
- F11
- F13
- Front passenger's side front seat inner belt
- Fsr+
- Fsr-
- Gauge fuse 7.5a
- Gbt
- Gnd
- Gps
- Gsp
- Gsw4
- H18
- H19
- H20
- Hazard warning signal switch assembly
- Hot in run or start
- I13
- Ia2
- Ic (center of dash)
- Ig+
- Ig1 fuse 10a
- Ign fuse 15a
- Ij1
- Il1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 5 (behind right side of dash)
- Left front air bag sensor (behind left side of front bumper)
- Left seat position air bag sensor
- Occupant classification ecu (front passenger's seat bottom)
- Occupant classification sensor (passenger's seat bottom)
- Pnk
- Right front air bag sensor (behind right side of front bumper)
- Rsca off ind
- Seat belt tension sensor
- Sil
- Srs ind
- Sw-
- Vbt
- Vps
Supplemental Restraints Wiring Diagram, Separate Seats (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Supplemental Restraints Wiring Diagram, Separate Seats (1 of 2) for Toyota Tacoma X-Runner 2013:
- (base of right "b" pillar) right front side air bag sensor
- (behind right side of dash) air bag squib (front passenger's air bag assembly)
- (center of dash) ib
- (right "b" pillar) right curtain shield air bag squib
- (under steering wheel pad) air bag squib (steering wheel pad)
- +sl
- +sr
- -sl
- -sr
- A21
- A22
- A23
- A24
- A25
- Access cab
- Bbd+
- Bbd-
- Bbl+
- Bbl-
- Bbp+
- Bbp-
- Bbr+
- Bbr-
- Bcl+
- Bcl-
- Bcr+
- Bcr-
- Bf2
- Bg2
- Canh
- Canl
- Center air bag sensor assembly (center of dash)
- Computer data lines system
- D2+
- D2-
- Dbe+
- Dbe-
- Double & access cab
- Driver's side front seat inner belt
- Dsp+
- Dsp-
- Fsp+
- Fsp-
- Icd+
- Icd-
- Icp+
- Icp-
- Ig1
- Ig2
- Ij1
- Left curtain shield air bag squib (left "b" pillar)
- Left front seat outer belt
- Left front side air bag sensor (base of left "b" pillar)
- Left rear side air bag sensor (double & access cab) (base of left "c" pillar)
- Left side air bag squib
- P-ab
- P2+
- P2-
- Paon
- Pd+
- Pd-
- Pp+
- Pp-
- Pre- tensioner
- Pretensioner
- Red
- Regular cab
- Right front seat outer belt
- Right rear side air bag sensor (double & access cab) (base of right "c" pillar)
- Right side air bag squib
- Rmil
- Rmsw
- Seat position air bag sensor
- Sfd+
- Sfd-
- Sfl+
- Sfl-
- Sfp+
- Sfp-
- Sil
- Spiral cable
Supplemental Restraints Wiring Diagram, Separate Seats (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for Supplemental Restraints Wiring Diagram, Separate Seats (2 of 2) for Toyota Tacoma X-Runner 2013:
- (below left center of dash) data link connector 3
- (left "b" pillar)
- +sl
- +sr
- -sl
- -sr
- Access cab
- Air
- Air bag on/off ind
- B17
- Bf1
- Bgnd
- Bh1
- Bsw
- C16
- Combination meter
- Computer data lines system
- Cpu
- Curtain air bag cutoff switch (4wd)
- Dia
- Driver side j/b (left side of dash)
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- F11
- F13
- Front passenger's side front seat inner belt
- Fsr+
- Fsr-
- Gauge fuse 7.5a
- Gnd
- H18
- H19
- H20
- Hazard warning signal switch assembly
- Hot at all times
- Hot in run or start
- I13
- Ia2
- Ic (center of dash)
- Ig+
- Ig1 fuse 10a
- Ign fuse 15a
- Il1
- Ind
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- Interior lights system
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 5 (behind right side of dash)
- Left front air bag sensor (behind left side of front bumper)
- Left front occupant classification sensor (left front of front passenger seat bottom)
- Left rear occupant classification sensor (left rear of front passenger's seat bottom)
- Occupant classification ecu (front passenger's seat bottom)
- Pnk
- Red
- Right front air bag sensor (behind right side of front bumper)
- Right front occupant classification sensor (right front of front passenger seat bottom)
- Right rear occupant classification sensor (right rear of front passenger seat bottom)
- Rsca off
- Sgd1
- Sgd2
- Sgd3
- Sgd4
- Sig1
- Sig2
- Sig3
- Sig4
- Sil
- Srs ind
- Svc1
- Svc2
- Svc3
- Svc4
- Sw-
TRANSMISSION
2.7L
2.7L, 4WD Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, 4WD Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (a/t)
- (differential) differential lock shift actuator assembly
- (m/t)
- (rear of cylinder head) (2.7l) eh
- (right rear of engine compt) (4.0l) ee
- 2-4
- 2.7l
- 4.0l
- 4wd
- 4wd control ecu (right side of dash)
- 4wd control switch
- 4wd fuse 20a
- 4wd position transfer indicator switch (transmission assembly)
- A13
- A18
- A19
- A21
- A22
- Add
- Add actuator assembly (front of engine)
- B17
- Bd1
- C13
- C14
- C20
- Differential lock switch
- Dl1
- Dl2
- Dm1
- Dm2
- Driver side j/b (left side of dash)
- E13
- E21
- Ec1
- Engine control module (behind right side of dash)
- F12
- F13
- Gnd
- H17
- Hot in run or start
- Ic (center of dash)
- Id1
- Ig1 2 fuse 10a
- Ind1
- Ind3
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 5 (behind right side of dash)
- L4 position transfer indicator switch (transmission assembly)
- Limit switch
- Mtn
- Pnk
- Red
- Rlp
- Rly1
- Rly2
- Spd
- Tl1
- Tl2
- Tl3
- Tm1
- Tm2
- Transfer shift actuator assembly (transmission assembly)
2.7L, 4WD Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, 4WD Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- (left side of dash) instrument panel j/b 1
- 4lo ind lamp
- 4wd ind lamp
- B14
- Bd1
- C10
- Combination meter
- Cpu
- Diode (clutch start) (m/t) (left side of dash)
- Driver side j/b (left side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Exi
- Exi4
- Gauge fuse 7.5a
- H13
- H18
- Hot in run or start
- Hot in start
- Hydraulic booster type
- Ia1
- Ib1
- Ig1 fuse 10a
- Ih1
- Ij1
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- Park/ neutral position switch (a/t) (trans- mission)
- Pnk
- Rear differential lock ind
- Rear differential transfer indicator switch (rear differential)
- Skid control ecu w/ actuator (hydraulic booster: left rear of engine compartment) (vacuum booster: right rear of engine compartment)
- Sp1
- Sta fuse 7.5a
- Vacuum booster type
2.7L, A/T Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, A/T Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- A/t oil temp ind
- A10
- At3
- Atd
- B11
- C10
- C11
- C12
- C13
- C14
- C16
- Canh
- Canl
- Combination meter
- Computer data lines system
- Cpu
- Data link connector 3 (below left center of dash)
- Driver side j/b (left side of dash)
- E03
- E12
- E15
- E18
- E19
- E22
- Eg (rear of cylinder head)
- Electronically controlled transmission solenoid (transmission)
- Engine control module (behind right side of dash)
- Etho
- H13
- Hot in run or start
- Ia1
- Ig1 fuse 10a
- Ih1
- Ih2
- Ij1
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 4 & 5 (behind right side of dash)
- Nco+
- Nco-
- Nssd
- Ot2+
- Ot2-
- Park/ neutral position switch (transmission)
- Pnk
- Red
- Shift lock control ecu (under center console)
- Skid control ecu w/ actuator (right rear of engine compt)
- Slt+
- Slt-
- Slu+
- Slu-
- Sp1
- Sp2+
- Sp2-
- Spd
- Starting/ charging system
- Tho1
- Transmission revolution sensor (turbine) (left side of transmission assembly)
- Vehicle speed sensor (electronically controlled transmission) (transmission)
2.7L, A/T Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, A/T Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- +bm
- A/t fluid temperature sensor (automatic transmission)
- A11
- A30
- A33
- Acc
- Accelerator position sensor (behind left side of dash)
- Am2
- Batt
- Driver side j/b (left side of dash)
- E17
- E18
- E20
- E21
- E22
- Ea (right front fender)
- Efi main relay
- Efi-main fuse 20a
- Eh (rear of cylinder head)
- Engine control module (behind right side of dash)
- Engine coolant temperature sensor (rear of engine)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- Eta
- Etcs fuse 10a
- Ethw
- Gauge fuse 7.5a
- Ge01
- Hot at all times
- I15
- Ia1
- Ig2
- Ign fuse 15a
- Ignition switch
- Igsw
- J/c 12 (behind right side of dash)
- Lock
- Mrel
- Nca
- Off
- Pnk
- Red
- Start
- Stop fuse 10a
- Stop lamp switch (bracket, above brake pedal)
- Stp
- Thoc
- Throttle body assembly (left top of engine)
- Thw
- Vcp2
- Vcpa
- Vcta
- Vpa
- Vpa2
- Vta
- Vta1
- Vta2
2.7L, Rear Differential Lock Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 2.7L, Rear Differential Lock Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (differential) differential lock shift actuator assembly
- 4wd control ecu (right side of dash)
- 4wd fuse 20a
- B14
- Bd1
- C10
- C13
- C14
- Combination meter
- Cpu
- Differential lock switch
- Driver side j/b (left side of dash)
- Gauge fuse 7.5a
- Gnd
- H17
- H18
- Hot in run or start
- Hydraulic booster type
- Ia1
- Ib1
- Id1
- Ig1 2 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- Limit switch
- Pnk
- Rear differential lock ind
- Rear differential transfer indicator switch (rear differential)
- Rlp
- Rly1
- Rly2
- Rr diff lock
- Skid control ecu w/ actuator (vacuum booster: right rear of engine compt) (hydraulic booster: left rear of engine compt)
- Sp1
- Spd
- Vacuum booster type
4.0L
4.0L, 4WD Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, 4WD Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (a/t)
- (differential) differential lock shift actuator assembly
- (m/t)
- (rear of cylinder head) (2.7l) eh
- (right rear of engine compt) (4.0l) ee
- 2-4
- 2.7l
- 4.0l
- 4wd
- 4wd control ecu (right side of dash)
- 4wd control switch
- 4wd fuse 20a
- 4wd position transfer indicator switch (transmission assembly)
- A13
- A18
- A19
- A21
- A22
- Add
- Add actuator assembly (front of engine)
- B17
- Bd1
- C13
- C14
- C20
- Differential lock switch
- Dl1
- Dl2
- Dm1
- Dm2
- Driver side j/b (left side of dash)
- E13
- E21
- Ec1
- Engine control module (behind right side of dash)
- F12
- F13
- Gnd
- H17
- Hot in run or start
- Ic (center of dash)
- Id1
- Ig1 2 fuse 10a
- Ind1
- Ind3
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- J/c 5 (behind right side of dash)
- L4 position transfer indicator switch (transmission assembly)
- Limit switch
- Mtn
- Pnk
- Red
- Rlp
- Rly1
- Rly2
- Spd
- Tl1
- Tl2
- Tl3
- Tm1
- Tm2
- Transfer shift actuator assembly (transmission assembly)
4.0L, 4WD Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, 4WD Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- (left side of dash) instrument panel j/b 1
- 4lo ind lamp
- 4wd ind lamp
- B14
- Bd1
- C10
- Combination meter
- Cpu
- Diode (clutch start) (m/t) (left side of dash)
- Driver side j/b (left side of dash)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Exi
- Exi4
- Gauge fuse 7.5a
- H13
- H18
- Hot in run or start
- Hot in start
- Hydraulic booster type
- Ia1
- Ib1
- Ig1 fuse 10a
- Ih1
- Ij1
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- Park/ neutral position switch (a/t) (trans- mission)
- Pnk
- Rear differential lock ind
- Rear differential transfer indicator switch (rear differential)
- Skid control ecu w/ actuator (hydraulic booster: left rear of engine compartment) (vacuum booster: right rear of engine compartment)
- Sp1
- Sta fuse 7.5a
- Vacuum booster type
4.0L, A/T Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, A/T Wiring Diagram (1 of 2) for Toyota Tacoma X-Runner 2013:
- (behind right side of dash) j/c 4 & 5
- 4wd
- 4wd circuit
- A/t oil temp
- A10
- A20
- At2
- At4
- Atd
- Atl
- B11
- B12
- C10
- C11
- C12
- C14
- Canh
- Canl
- Combination meter
- Computer data lines system
- Cpu
- Driver side j/b (left side of dash)
- E03
- E04
- E05
- E10
- E11
- E12
- E13
- E14
- E15
- Ee (right rear of engine compt)
- Ef (left rear of engine compt)
- Electronically controlled transmission solenoid (transmission)
- Engine control module (behind right side of dash)
- H13
- Hot in run or start
- Hydraulic booster type
- Ia1
- Ic (center of dash)
- Ig1 fuse 10a
- Ih1
- Ij1
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 4 & 5 (behind right side of dash)
- J/c 5 (behind right side of dash)
- Me01
- Nssd
- Nssl
- Nt+
- Nt-
- Ot+
- Ot-
- Ot2+
- Ot2-
- Park/neutral position switch (transmission)
- Pnk
- Red
- Shift lock control ecu (under center console)
- Skid control ecu w/ actuator (hydraulic booster: left rear of engine compt) (vacuum booster: right rear of engine compt)
- Sl1+
- Sl1-
- Sl2+
- Sl2-
- Slt+
- Slt-
- Slu+
- Slu-
- Sp1
- Sp2+
- Sp2-
- Spd
- Starting/ charging system
- Tach
- Tho1
- Tho2
- Transmission revolution sensor (electronically controlled transmission) (right rear of transmission assembly)
- Transmission revolution sensor (turbine) (left side of transmission assembly)
- Vacuum booster type
4.0L, A/T Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, A/T Wiring Diagram (2 of 2) for Toyota Tacoma X-Runner 2013:
- +b2
- +bm
- A11
- A30
- A33
- Acc
- Accelerator position sensor (behind left side of dash)
- Am2
- Batt
- Data link connector 3 (below left center of dash)
- Driver side j/b (left side of dash)
- E01
- E02
- E10
- E11
- E12
- E13
- E14
- Ea (right front fender)
- Ea1
- Ee (right rear of engine compt)
- Efi fuse 20a
- Efi relay
- Engine control module (behind right side of dash)
- Engine coolant temperature sensor (top center of engine)
- Engine room j/b (left side of engine compt)
- Engine room r/b (left front of engine compt)
- Epa
- Epa2
- Eta
- Etcs fuse 10a
- Ethw
- Gauge fuse 7.5a
- Ge01
- Hot at all times
- Hydraulic booster type
- I15
- Ia1
- If1
- Ig2
- Ign fuse 15a
- Ignition switch
- Igsw
- Instrument panel j/b 1 (left side of dash)
- Lock
- Mrel
- Nca
- Off
- Pnk
- Red
- Start
- Stop fuse 10a
- Stop lamp switch (bracket, above brake pedal)
- Stop lp ctrl relay
- Stp
- Tac
- Throttle body assembly (front top of engine)
- Thw
- Vacuum booster type
- Vcp2
- Vcpa
- Vcta
- Vpa
- Vpa2
- Vta1
- Vta2
4.0L, Rear Differential Lock Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 4.0L, Rear Differential Lock Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (differential) differential lock shift actuator assembly
- 4wd control ecu (right side of dash)
- 4wd fuse 20a
- B14
- Bd1
- C10
- C13
- C14
- Combination meter
- Cpu
- Differential lock switch
- Driver side j/b (left side of dash)
- Gauge fuse 7.5a
- Gnd
- H17
- H18
- Hot in run or start
- Hydraulic booster type
- Ia1
- Ib1
- Id1
- Ig1 2 fuse 10a
- Instrument panel j/b 1 (left side of dash)
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J/c 13 (behind right kick panel)
- J/c 14 (behind right kick panel)
- Limit switch
- Pnk
- Rear differential lock ind
- Rear differential transfer indicator switch (rear differential)
- Rlp
- Rly1
- Rly2
- Rr diff lock
- Skid control ecu w/ actuator (vacuum booster: right rear of engine compt) (hydraulic booster: left rear of engine compt)
- Sp1
- Spd
- Vacuum booster type
WARNING SYSTEMS
Key Reminder & Seat Belt Warning Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Key Reminder & Seat Belt Warning Wiring Diagram for Toyota Tacoma X-Runner 2013:
- A21
- A23
- Access cab
- Acty
- Air bag sensor assembly center (center of dash)
- Ba (under
- Bf1
- Bgnd
- Bh1
- Bi2
- Bj2
- Body ecu
- Bsw
- Buckle switch
- Buzzer
- C16
- Canh
- Canl
- Combination meter
- Computer data lines system
- Cpu
- Dcty
- Dia
- Door ind
- Double cab & regular cab
- Driver side j/b (left side of dash)
- Driver's seat belt ind
- Driver's seat)
- Driver's side door courtesy switch
- Driver's side front seat inner belt
- Ecu-b fuse 7.5a
- Engine room r/b (left front of engine compt)
- F13
- Front passenger seat belt warning light
- Front passenger's side front seat inner belt
- Fsp+
- Fsp-
- Fsr+
- Fsr-
- Gauge fuse 7.5a
- Hazard warning signal switch assembly
- Hot at all times
- Hot in on or start
- Ic (center of dash)
- Ig+
- Ig1 fuse 10a
- Ii1
- Ij1
- Instrument panel j/b 2 (right side of dash)
- J/c 1 (left kick panel)
- J12
- K10
- K13
- Occupant classification ecu (front passenger's seat bottom)
- Pbew
- Pnk
- Red
- Rmil
- Rsca off
- Unlock warning switch
- W/ bench seat
- W/ separate seat
Tire Pressure Monitoring Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Tire Pressure Monitoring Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (left side of dash) instrument panel j/b 1
- (right side of dash) instrument panel j/b 2
- (vacuum booster type: right rear of engine compt) (hydraulic booster type: left rear of engine compt) skid control ecu w/ actuator
- +5v
- 2.7l
- 4.0l
- C13
- C14
- C16
- Clsw
- Combination meter
- Computer data lines system
- Cpu
- Driver side j/b (left side of dash)
- E14
- E22
- Eb (near battery)
- Ecu-b fuse 7.5a
- Engine control module (behind right side of dash)
- Engine room r/b (left front of engine compt)
- F10
- Gauge fuse 7.5a
- Gnd
- Gnd2
- Hot at all times
- Hot in on or start
- Ia1
- Ie2
- Ig1 2 fuse 10a
- Ij1
- Ind
- J/c 1 (left kick panel)
- J/c 4 & 5 (behind right side of dash)
- K13
- Rda
- Red
- Rf5v
- Sil
- Sp1
- Spd
- Tach
- Tire pressure ind
- Tire pressure warning antenna & receiver (right side of dash)
- Tire pressure warning ecu (center of dash)
- Tire pressure warning reset switch
- W/ hydraulic booster type
- W/ vacuum booster type
WIPER/WASHER
2-Speed Wiper/Washer Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for 2-Speed Wiper/Washer Wiring Diagram for Toyota Tacoma X-Runner 2013:
- (near battery) eb
- C12
- C13
- Combination switch
- Driver side j/b (left side of dash)
- H15
- Hot in run or start
- Ia4
- Ic (center of dash)
- Mist
- Off
- Pnk
- Washer switch
- Windshield washer motor (washer fluid reservoir)
- Windshield wiper motor (right side of firewall)
- Wip fuse 30a
- Wiper switch
- Wsh fuse 10a
Interval Wiper/Washer Wiring Diagram for Toyota Tacoma X-Runner 2013
List of elements for Interval Wiper/Washer Wiring Diagram for Toyota Tacoma X-Runner 2013:
- C12
- C13
- Combination switch
- Driver side j/b (left side of dash)
- Eb (near battery)
- H15
- Hot in run or start
- Ia4
- Ic (center of dash)
- Int
- Mist
- Off
- Pnk
- Washer switch
- Windshield washer motor (washer fluid reservoir)
- Windshield wiper motor (right side of firewall)
- Wip fuse 30a
- Wiper relay
- Wiper switch
- Wsh fuse 10a