AUTOMOTIVE ELECTRICIANS PORTAL

ANTI-LOCK BRAKES – Mercury Mountaineer 2003 – SYSTEM WIRING DIAGRAMS

ANTI-LOCK BRAKES

Anti-lock Brakes Wiring Diagram, with IVD for Mercury Mountaineer 2003

Anti-lock Brakes Wiring Diagram, with IVD for Mercury Mountaineer 2003 https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html Automotive Electricians Portal FZCO Automotive Electricians Portal FZCO
Download PDF file

List of elements for Anti-lock Brakes Wiring Diagram, with IVD for Mercury Mountaineer 2003:

  • (in dash panel to
  • (left front of engine compt) g101
  • Abs control module (left front side of engine compt)
  • Abs test connector (at left side of engine compartment)
  • Battery junction box (bjb) (left side of engine compartment, at fender apron)
  • Brake booster sensor (on front of brake booster)
  • Brake fluid level switch (mounted on right side of master cylinder)
  • Brake pedal position switch (above brake pedal)
  • Breakout to left horn)
  • C175a
  • C270a
  • C270b
  • C270d
  • C270h
  • C281b
  • Central junction box (cjb) (behind left side of dash)
  • Computer data lines system
  • Engine harness, near
  • Exterior lights system
  • Four-wheel drive control module (under passenger dash panel)
  • Fuse 10a
  • Fuse 15a
  • Fuse 30a
  • Fuse 40a
  • Fuse 7.5a
  • G101 (left front of engine compt)
  • Gnd
  • Hot at all times
  • Hot in start or run
  • Interior lights system
  • Left front wheel speed sensor
  • Left rear wheel speed sensor
  • Powetrain control module (pcm) (at right side engine bulkhead)
  • Primary brake pressure sensor (on master cylinder)
  • Red
  • Red/ pnk
  • Red/pnk
  • Redundant pedal switch (under left side dash panel)
  • Right front wheel speed sensor
  • Right rear wheel speed sensor
  • S120 (near breakout to left horn)
  • S127 (near breakout to a/c clutch cycling pressure switch)
  • S171
  • S175
  • S176
  • S179 (in dash panel to engine harness, near breakout to windshield wiper motor)
  • S264
  • Secondary brake pressure sensor (on brake booster)
  • Steering position sensor
  • Tan
  • Traction control switch
  • Vbatt
  • Vpwr
  • Yaw velocity sensor (below center console)

Anti-lock Brakes Wiring Diagram, without IVD for Mercury Mountaineer 2003

Anti-lock Brakes Wiring Diagram, without IVD for Mercury Mountaineer 2003 https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html Automotive Electricians Portal FZCO Automotive Electricians Portal FZCO
Get access to all wiring diagrams of the carDownload PDF file

List of elements for Anti-lock Brakes Wiring Diagram, without IVD for Mercury Mountaineer 2003:

  • (near breakout to windshield wiper motor) s120
  • Abs control module (left front side of engine compt)
  • Abs test connector (at left side of engine compartment)
  • Battery junction box (bjb) (left side of engine compt, at fender apron)
  • Brake fluid level switch (mounted on right side of master cylinder)
  • Brake pedal position switch (above brake pedal)
  • Brake pressure switch mounted on master cylinder)
  • C270b
  • C270d
  • C281b
  • Central junction box (cjb) (behind left side of dash)
  • Computer data lines system
  • Four-wheel drive control module (under passenger dash panel)
  • Fuse 10a
  • Fuse 15a
  • Fuse 2a
  • Fuse 30a
  • Fuse 40a
  • G101 (left front of engine compt)
  • Gnd
  • Hot at all times
  • Hot in start or run
  • Left front wheel speed sensor
  • Rear axle speed sensor (on rear differential)
  • Right front wheel speed sensor
  • S127 (in dash panel to engine harness, near breakout to a/c clutch cycling pressure switch)
  • Scp+
  • Scp-
  • Vbatt
  • Vpwr