CRUISE CONTROL
3.5L VIN L
3.5L VIN L, Cruise Control Wiring Diagram for Buick Rendezvous CXL 2006
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 3.5L VIN L, Cruise Control Wiring Diagram for Buick Rendezvous CXL 2006:
- (left side of engine compt)
- (not used)
- 5 volt ref
- 5 volt reference
- A2 c1
- Accelerator pedal position (app) sensor
- All times
- App sensor 1 sig
- App sensor 2 sig
- Bat
- Body control module (bcm) (in console, above fuse block, in center console)
- C103
- Center console fuse block (in center console)
- Class 2 serial data
- Computer data lines system
- Cruise ctrl on switch sig
- Cruise fuse 10a
- Cruise indicator
- Electronic brake control module (ebcm)
- F11
- G117 (engine compartment, on bell housing, above starter)
- Ground
- Hazrd lamp fuse 40 15a
- Hot at
- Hot in run or start
- Hot w/ ptrain relay energized
- Ign
- Ignition 1
- Instrument panel cluster (ipc)
- Ipc class 2 serial data
- Logic
- Low reference
- Off
- Pnk
- Powertrain control module (pcm) (at left side of engine compartment, in air cleaner assembly)
- Pt rly fuse 15a
- R/a
- Radio (if equipped)
- Rear parking assist (rpa) module (if equipped) (behind front center dash console)
- Resume/accel sw sig
- S106
- S117
- S141
- S209 (i/p harness, left side of dash, 7.5 cm from p101)
- Serial data (pri)
- Serial data (sec)
- Set sw
- Set/coast sw sig
- Stop lamp sw sig
- Stop lamp switch
- Stop lamp switch (on brake pedal support)
- Tan
- Tcc brake switch
- Tcc brake switch sig
- Throttle actuator control (tac) module
- Trn sig flshr/hazrd flshr module 10
- Turn signal/ multifunction switch
- Uart serial data (primary)
- Uart serial data (secondary)
- Underhood fuse block (front of right wheelhouse, above battery)
- Vehicle speed sensor (vss) (on transmission)
- Vehicle speed sig
- Vss high signal
- Vss low signal
3.6L VIN 7
3.6L VIN 7, Cruise Control Wiring Diagram for Buick Rendezvous CXL 2006
List of elements for 3.6L VIN 7, Cruise Control Wiring Diagram for Buick Rendezvous CXL 2006:
- 5 v ref 3
- A2 c1
- All times
- Bat
- Body control module (bcm) (in console, above fuse block, in center console)
- Center console fuse block (in center console)
- Class 2 serial data
- Computer data lines system
- Cruise ctrl on sw sig
- Cruise fuse 10a
- Cruise indicator
- Electronic brake control module (ebcm) (left side of engine compt)
- Engine control module (ecm)
- F11
- G134
- Gmlan serial data bus +
- Gmlan serial data bus -
- Ground
- Hazrd lamp fuse 40 15a
- Hot at
- Hot in run or start
- Ign
- Instrument panel cluster (ipc)
- Ipc class 2 serial data
- Logic
- Low ref
- Off
- Off off
- On on
- Pnk
- R/a r/a
- Radio
- Rear parking assist (rpa) module (if equipped) (behind front center dash console)
- Resume/accel sw
- S141
- S209 (i/p harness, left side of dash, 7.5 cm from p101)
- Set sw
- Set/coast sw sig
- Stop lamp sw sig
- Stop lamp sw signal
- Stop lamp switch
- Stop lamp switch (on brake pedal support)
- Tan
- Tcc brake switch
- Tcc/brake sw sig
- Throttle actuator control (tac) module
- Throttle actuator control close
- Throttle actuator control open
- Tp sensor 1 signal
- Tp sensor 2 signal
- Transmission control module (tcm) (inside air cleaner assembly)
- Trn sig flshr/hazrd flshr module 10
- Turn signal/ multifunction switch
- Underhood fuse block (front of right wheelhouse, above battery)
- Vehicle speed sensor (vss) (on transmission)
- Vehicle speed sig
- Vss high signal
- Vss low signal