CRUISE CONTROL – Chevrolet Corvette Z06 2008 – SYSTEM WIRING DIAGRAMS

CRUISE CONTROL

Cruise Control Wiring Diagram, A/T for Chevrolet Corvette Z06 2008

List of elements for Cruise Control Wiring Diagram, A/T for Chevrolet Corvette Z06 2008:

• 5 volt reference
• 5-volt reference 1
• 5-volt reference 2
• 5v ref
• Accelerator pedal position sensor (app) (on top of accelerator pedal, part of mounting bracket)
• App sensor 1 signal
• App sensor 2 signal
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal pos sw sig
• Brake pedal position sensor (mounted on brake pedal bracket)
• C4 x4
• Computer
• Computer data lines system
• Control (tac) motor
• Cruise control switch
• Cruise ctrl set/coast & resume/ acc sw signal
• Cruise switch fuse 2a
• Data lines
• Distribution
• Driver information center
• E8 x4
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Head up display (hud) (if equipped)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot w/ run/crank relay energized
• Hud class 2 serial data
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J211 (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• Logic
• Low ref
• Low reference
• Message request
• Nca
• Off
• Pnk
• Power
• Radio
• Res+
• Serial data bus +
• Serial data bus -
• Set-
• Stop lamp sw sig
• System
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Throttle actuator m
• Throttle body assembly (upper front center of engine, forward of intake manifold)
• Throttle position (tp) sensor
• Tp sensor 1 signal
• Tp sensor 2 signal
• Transmission control module (tcm) (in engine compt)
• Turn signal/multi-function switch
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sig
• X400

Cruise Control Wiring Diagram, M/T for Chevrolet Corvette Z06 2008

List of elements for Cruise Control Wiring Diagram, M/T for Chevrolet Corvette Z06 2008:

• (tac) motor
• (tp) sensor
• 5 volt reference
• 5-volt reference 1
• 5-volt reference 2
• 5v ref
• Accelerator pedal position sensor (app) (on top of accelerator pedal, part of mounting bracket)
• App sensor 1 signal
• App sensor 2 signal
• Body control module (bcm) (mounted on toe board, in right footwell)
• Brake pedal pos sw sig
• Brake pedal position sensor (mounted on brake pedal bracket)
• C4 x4
• Clutch pedal position (cpp) sensor
• Clutch pedal sen sig
• Clutch sen ctrl
• Computer
• Computer data lines system
• Control
• Cruise control switch
• Cruise ctrl set/coast & resume/ acc sw signal
• Cruise switch fuse 2a
• Data lines
• Driver information center
• Engine control module (ecm) (behind right front fender, between wheelhouse & dash panel)
• Head up display (hud) (if equipped)
• High speed gmlan serial data bus +
• High speed gmlan serial data bus -
• Hot w/ run/crank relay energized
• Hud class 2 serial data
• Instrument panel cluster (ipc)
• Ipc class 2 serial data
• J211 (right ignition control module jumper, 4.0 cm from breakout to ignition coil/module 4)
• Logic
• Low ref
• Low reference
• Message request
• Nca
• Off
• Pnk
• Radio
• Res+
• Serial data bus +
• Serial data bus -
• Set-
• Stop lamp sw sig
• System
• Tac motor ctrl 1
• Tac motor ctrl 2
• Tan
• Throttle actuator
• Throttle body (upper front center of engine)
• Throttle position
• Tp sensor 1 signal
• Tp sensor 2 signal
• Turn signal/multi-function switch
• Underhood fuse block (on right side of engine compt)
• Vehicle speed sensor (vss) (on top right side of differential)
• Vehicle speed sig
• Vss high sig
• Vss low sig