DescriptionThe geared motor for opening the boot ('boot 'release') is activated by the remote control in two ways:independently of the doors: there is a special button in the remote control that allows the boot only to be unlocked: the boot is released and rises slightly. The operation is signalled by the direction indicators flashing twice. the boot returns to its status prior to opening when reclosed.23in this way the unlocking of the doors leaves the boot locked. at the same time and together with the unlocking of the doors: the tailgate is considered, to all intents and purposes, as a fifth door: for the control logic, see 2399254SeeE3040CENTRAL LOCKINGA special feature on the control panel can be used to choose the two methods described above:The tailgage (after being unlocked) can only be opened from the outside of the vehicle using the electric opening handle located above the number plate.The boot opening function is disabled (the tailgate does not open) at vehicle speeds above 10 km/h to prevent undesired opening whilst driving caused, for example, by vibration of the exterior handle (on very uneven road surfaces).The boot opening circuit is protected by a special fuse located in the unit under the dashboard.The remote control receiver aerial is connected directly to the Body Computer which contains the electronics for the actual receiver.
Functional description The 'boot open' signal is sent by the switch located in the handle near the number plate light assembly F52 to pin 35 of connector E of the Body Computer M1. The RF aerial receiver P93 sends the Body Computer M1 the open/close signal for the doors and also the boot, in accordance with the logic described previously, to pins 21 and 31 of connector B SeeE3040 CENTRAL LOCKING . The Body Computer M1 implements the boot release function in accordance with the control strategy described - pin 11 of connector F via the line supplied by fuse F38 of the underfacia junction unit B2, pin 18 of connector D - to control operation of boot catch motor N57. The boot unlocking function, inside the Body Computer M1 pin 1 of connector F; also has a dedicated earth connection: pin 20 of connector F. The geared motor N57 is supplied until the opening of the boot is detected: the boot not properly closed signal is sent to the switch I11 which is connected to pin 24 of connector E.23 the contact in question signals the boot not properly closed condition; the switch is fitted with another contact which signals the boot open condition, this contact is used for the boot light function. 2399213SeeE2520GLOVE COMPARTMENT LIGHT - LUGGAGE COMPARTMENT LIGHT - SUN VISOR LIGHT
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2050746
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting212400802-7040A37fuse box cover - r r1. Disconnect the electrical connections (1a, 1b, 1c, 1d, 1e, 1f).2. Undo the bracket retaining bolt.3. Slightly move the bracket (3a) for the dashboard trim and undothe bolt (3b).4. Undo the other bolts securing the body computer/junction unit.5. Slightly move the body computer/junction unit assembly.6. Disconnect the electrical connections (6a, 6b, 6c).7. Recover the body computer/junction unit.2050752
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050753
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect electronic control unit electrical connections (1a),(1b), (1c).2. Undo the bolts.3. Recover the control unit.2050754
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection for the microswitch.2. Undo the bolts.3. Move the lock (3a) slightly and disconnect the electrical connection(3b) for the motor.4. Remove the lock assembly (4a) releasing the emergency openingcable (4c) from the retainers (4b).2400755-7015B70tail-gate lock motor - r r and check lock supplyline , if necessary. 2050996
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the electrical connection.2. Undo the nuts securing the outer handle.2050999
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
