DescriptionThere are three ashtrays in the car: oneis in the centre of the dashboard, and two are in the rear doors.The front ashtray is lit up when the sidelights are on (). it houses a standard power point; the ring roundthe power point is lit with the side lights on. The cigar lighterresistance is located in the socket, but it can be used for connectionto other instruments or equipment (provided they operate at 12 V).To operate the cigar lighter, simply press the knob: after a fewseconds it pops out automatically, ready for use.The socket has a heat protection device:if devices with high energy absorption are connected, this protectioncuts off the supply.The current socket circuit is protectedby a special fuse and is operated by the relay which is excludedwhen the ignition is switched on and is located in the junctionunit.One more power point is also present inthe luggage compartament, with similar specifications to those ofthe cigar lighter; The power point circuits are protected by a specificfuse.All power points are supplied only withthe ignition turned on.
Functional description The power socket / cigarette lighter P50 issupplied (at pin 2) by the line controlled by the ignition (INT/A)for the relay R1 protected by the fuse F15 : both arehoused in the junction unit B1 . Pin 3 of socket P50 provides theearth from C20 . The ring nut for the power socket is litup (at pin 1) when the side lights are on by means of the line comingfrom the steering column switch unit H5 switch and is protectedby the controls illumination fuse F4 of the additional fuseunit B98B . The same supply line with the side lightson also lights up the ashtray light G35 . Rear power point P52 is suppliedat pin 2 of ignition-operated line (INT/A) via a dedicated fuse.The ring nut for the power socket is lit up (at pin 1) when the sidelights are on by means of the line coming from the steering columnswitch unit H5 switch and is protected by the controls illuminationfuse F4 of the additional fuse unit B98B .
0Removing201Refitting21Place the car on a ramp.Undo the bolt securing the bracket on thebattery mount.Release the battery from the anchoragebracket complete with strap and remove.
5530B14
769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour:a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery;a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For more details 3238420See subassembly5530 CURRENT GENERATOR . 768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360').Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows: If the voltage without load is less than12.10 V, replace the battery ( 32384295530B10battery - r+r ). If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery ( 32384305530B14battery - recharge ). If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
5530B22
0Removing201Refitting21Place the car on the liftingbridge.1. Open engine compartment cap and disconnect battery negative terminal.2. Disconnect mass terminal on side member.3. Lift the car and disconnect mass terminal on gearbox.4. Lower the car again and remove battery earth lead.2018767
0Removing201Refitting21Disconnect the battery negative terminal.1. Open the protective cover2. Loosen the nut and disconnect the ABS supply lead3. Loosen the nut and disconnect the starter motor supply lead4. Undo the clip and undo the box retaining bolts.5. Loosen the battery positive terminal nut.2018769
5530B52
0Removing201Refitting213238429-5530B10battery - r+rRelease the air duct hose from the mountingbracket on the drip tray. Remove the relay shield.1. Release the relays from the battery drip tray and remove them.2. Undo the nut fixing the air filter mounting bracket to the batterydrip tray.3. Undo the two fixing nuts (3a) and move the connections/electricalwiring mounting bracket (3b) aside.4. Release the accelerator cable from the fastening on the bracket.2018771
0Removing201Refitting21Please note the following warning.7691. Working on both sides of the longitudinal mount, prise off thecovers using the appropriate tool. 7692. Undo bolts (2a) and recover washers (2b) and gaskets (2c).3. Remove the longitudinal mount.4. Recover the gaskets.2019528
7065C30
0Removing201Refitting211. Lower handle and remove badge.2. Unscrew screws.3. Remove handle (3a) by removing it from stops (3b).2019529
7065C34
0Removing201Refitting211. Unscrew I' sun blind fixing screw.2. Remove I' sun blind (2a) by releasing it from stop (2b).3. Remove and lift I' grab handle badge.4. Unscrew I' grab handle fixing screw.5. Remove l' grab handle.2019530
7065C42
0Removing201Refitting211. Open the ashtray and undo the screws.2. Move the ashtray over slightly.3. Disconnect the electrical connections (3a, 3b).2019531
7065C84
0Removing201Refitting211. Remove radio compartment (1a) from stops (1b) and extract itslightly.2. Disconnect electric connections (2a, 2b) from chambers.2019535
7065C58
0Removing201Refitting211. Working on the interior rearview mirror mounting, remove thecover, releasing it from the retainers. 2. Disconnect the electrical connections (2a (2b).3. Working on the recess (3a), open the cover (3b) of the rain sensor.2019536
7065C68
0Removing201Refitting211. Only for vehicles equipped with a Telepass holder. Undo the bolt(1a), move the trim (1b) and disconnect the electrical connection(1c). 2019540
7065C69
0Removing201Refitting21The following procedure showsplate reattachment since it is not possible to detach plate fromglass if it has been properly fixed.769
7065C72
0Removing201Refitting213238986-7065C42ashtray (one) r+r1. Take out the ashtray.2. Extract the cigar lighter housing (2a) using the special tool.The tool should engage in the recesses (2b) of the cigar lighterhousing.2019544
0Removing201Refitting211. Disconnect the electrical connections.2. Open the socket cover.3. Wtihdraw the socket (3a) (cigarette lighter type) using the specialtool (3b).767The tool must engage in the recesses(3c) of the cigarette lighter seating.4. If necessary, remove the ring nut with cover from its seating.2019550
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.