DescriptionThe direction indicators and hazard warning lights delimit the outer dimensions of the car.The left and right direction indicators are operated by raising or lowering the appropriate lever on the stalk unit.The hazard warning lights (right and left direction indicators operated simultaneously) are turned on by the pressing the red button at the centre of the dashboard.The direction indicators work with the ignition on, while for safety reasons, the hazard warning lights can be turned on at any time, as they are supplied directly from the battery.The rear direction indicators consist of a set of 4 LEDs controlled by a specific electronic control unit.Two warning lights on the dashboard, also flashing, indicate when the left and right direction indicators are turned on.On the red button for the hazard warning lights, there is an LED which lights up the relevant symbol when the hazard lights are switched on.The hazard warning lights are also operated by the alarm system, which is connected directly to the power supply to the lights.
Functional description The direction indicators and hazard warning lights are controlled by an electronic intermittence device R2 located in junction unit B1 . The supply for the device reaches pin 6 directly from the battery (maxifuse CENTR of B5 ) via fuse F8 of junction unit B1 ; Pin 2 is earthed. Hazard warning light operation is controlled by a switch located in unit H35 :when the button is pressed, an earth signal is sent to pin 3 of device R2 of B1 . Pin 2 of H35 is operated when the ignition is turned on (INT/A) via fuse F5 of junction unit B1 ; this line is responsible for lighting up control panel H35 . The turn signals are activated by stalk unit H5 . The supply is controlled by the ignition (INT/A) via fuse F1 of junction unit B1 ; when the lever is operated in both directions, a signal is sent to pin 7 (left side arrows) and pin 1 (right side arrows) for device R2 of B1 . Intermittent device R2 of B1 generates two signals that supply the turn signals: the right hand signal from pin 5 ( F11 , F21 , F31 ); the left hand one from pin 4 ( F10 , F20 , F30 ). When a trailer is connected, a signal is sent from pin 8 to a special warning light located in the instrument panel E50 . The tail-lights in clusters F30 and F31 are not conventional bulbs but electronic leds. A special direction indicator control unit M83 is therefore fitted. This monitors tail-light activation signals to detect anomalies and controls the various warning lights. The supply for device M83 reaches pin 6 directly from the battery (maxifuse CENTR of B5 ) via fuse F8 of junction unit B1 ; Pin 8 is earthed. Pins 10 and 7 receive signals from device R2 of B1 for right and left hand side operation. The device is connected to the turn signals: located in clusters F30 and F31 with two feedbacksignals from pins 1 and 2. The warning lights for the direction indicators, located inside the instrument panel E50 , are also operated by pins 11 and 17; the red LED in switch H35 , which lights up the ideogram with the hazard warning lights switched on, is operated by pin 16. All the hazard warning lights are also operated by the alarm system control unit M30 (pins 1 and 2 of connector B), which is connected directly to the light power supply ( 3310008SeeE7021ASR / TCS ).
0Removing201Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
0Removing201Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
0Removing201Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Lower the steering wheel and move it back.1. Undo the bolts (1a) and remove the upper half casing for thesteering column (1b).2010703
5560B12
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). Open the fuse carrier compartment flap.1. Using the tool (1a) and pushing the fuse carrier compartment,remove the surround (1b) complete with switches.2. Disconnect the elelectrical connections (2a), (2b) and (2c) andremove the surround complete with switches.2010706
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Release the retaining spring (1a) and remove the protective cover(1b).2. Disconnect the electrical connection from the lamp.3. Release the retaining spring (3a) and remove the lamp (3b) fromthe light cluster.767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010662
5540B26
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Rotate the bulb holder (1a) in an anti-clockwise direction untilit is released from the light cluster (1b).2. Disconnect the electrical connection (2a) and extract the bulbholder.3. Separate the lamp from the bulb holder (press fit).767If the lamp is working properly,avoid touching the bulb with your hands. If this does happen, cleanthe bulb with alcohol.2010663
5540B38
Prepare the vehiclecomplete with spare wheel, tools, fluids, fuel reserve.Check that the tyre inflation pressureis correct.Place the headlamp alignment switch inposition '0'.Position the vehicle on a flat surface,perpendicular to a screen with an opaque surface, 10 metres away, whichcontains the following lines.1. V - V: vertical corresponding to the trace of the vehicle symmetryplane.2. C - C: traces of the vertical planes passing through the referencecentres of the light clusters.3. HC - HC: horizontal corresponding to the height from the groundof the reference centres for the light clusters.4. AC - AC: horizontal 11 cm below the HC - HC line.5. Lines inclined at 15° as illustrated in the diagram.2010664
5540B40
0Removing201Refitting21Position the vehicle on theramp. Make sure that the ignition is OFF (STOPposition), then disconnect the negative battery terminal (referto op. 33148615530B10battery - r+r ). 3315196-7040D12engine front side cover (one) lh or rh - r r . 1. Disconnect the electrical connection from the exhaust gas headlampcontrol unit.2. Disconnect the electrical connection from the headlamp alignmentmotor.2010666
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Disconnect the electrical connection from the front directionindicator bulb.2. Rotate the bulb holder in an anti-clockwise direction and extractit.3. Remove the bulb for the front direction indicator from the bulbholder (bayonet fitting).2010694
5550C22
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 767Protect the panel surroundingthe side repeater using paper tape to prevent the paintwork from beingdamaged.1. Remove the side repeater (1a) using the tool (1b).2. Disconnect the electrical connection from the side repeater andremove it.3. Rotate the bulb holder (3a) in an anti-clockwise direction andextract it, then remove the bulb (3b) which is a press fit.2010695
5550C40
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the bolts (1a) and remove the right and left trims (1b).2010696
0Removing201Refitting21Ensure that the ignition keyis in stop position, then disconnect the battery negative terminal1. Undo the bolt (1b) and open the fuse access cover (1b).2. Remove the complete exterior light switch (2a) from its housingusing the tool (2b).767Exert pressure inside the exteriorlights switch to facilitate its removal.3. Disconnect the electrical connections (3a), (3b) and (3c) andremove the exterior lights switch (3d).2010651
5540A56
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010652
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the fixing knob (1b) and open the access cover (1a) .2. Disconnect the electrical connection from the inner rear lightcluster.3. Undo the nuts (3a) and remove the inner rear light cluster (3b).2010654
5540A74
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Open the access cover after having undone the fixing knob.2. Release the retaining tabs (2a) and extract the bulb holder (2b)from its housing.3. Replace the rear fog lamps bulb (3a) or the reversing lightsbulb (3b) or the side lights bulb (3c).2010655
5540A80
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Undo the knob (1b) and open the protective cover (1a).2010656
5540A94
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Using the tool (1a), remove the complete number plate light (1b).2. Disconnect the electrical connection and remove the number platelight.2010658
0Removing201Refitting21With the ignition key in the stop position,disconnect the battery negative terminal.1. Release the gear lever boot from its seat on the console.2. Undo the handbrake lever boot stud from its seat on the consoleand release from the lever.3. Unscrew the console retaining bolts. 4. Disconnect the cigar lighter and ashtray light electrical connection.5. Remove the trim by withdrawing from the handbrake lever.2010988
7040L40
0Removing201Refitting211. Unscrew the retaining bolt in the upper corner of the sill plate.2. Use tool (2a) to prise sill plate (2b) up from the underlyingretainers.2010989
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.