All Wiring Diagrams for Chevrolet Metro 1999 model

AIR CONDITIONING

Compressor Wiring Diagram for Chevrolet Metro 1999

List of elements for Compressor Wiring Diagram for Chevrolet Metro 1999:

(i/p harness, 8 cm from blower motor breakout)
A/c 1 relay
A/c 2 relay
A/c compressor clutch
A/c compressor control module (below right side of dash, on evaporator case)
A/c fuse 15a
A/c off
A/c refrigerant temperature switch (behind right side of dash)
A/c relay
A/c req
A/c switch
Blower speed selector switch
Dual pres sw
Dual pressure switch (right side of engine compartment, near strut tower)
Evap temp
Fuse box
G103 (right front of engine compt)
Heater fuse 20a
Hot at all times
Hot in on
Junction block
Off
Pnk
Powertrain control module (pcm) (behind right side of dash)
Relay box
S122 (main harn, at relay box)
S134 (a/c jumper harn, right front of engine compartment)
S233
Sensor ground

Heater Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Heater Wiring Diagram for Chevrolet Metro 1999:

1995 vftc c
Blower motor
Blower motor resistor (in blower housing assembly)
Blower speed selector switch
Engine controls system
G202 (center of dash)
Heater fuse 20a
Hot in on
Junction block
Off
Pnk
S232 (i/p harness, behind center of dash)
S233 (i/p harness, 8 cm from blower motor breakout)
S238 (i/p harness, 3 cm from blower motor breakout)

Manual A/C Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Manual A/C Wiring Diagram for Chevrolet Metro 1999:

(i/p harness, 8 cm from blower motor breakout)
(i/p harness, behind right side of dash)
(main harn, 18 cm from left firewall grommet)
(main harn, behind left side of dash)
1995 vftc c
A/c 1 relay
A/c 2 relay
A/c compressor clutch
A/c compressor control module (below right side of dash, on evaporator case)
A/c condenser fan motor
A/c fuse 15a
A/c off
A/c relay
A/c req
A/c switch
Blower motor
Blower motor resistor (in blower housing assembly)
Blower speed selector switch
Dual pres sw
Dual pressure switch (right side of engine compartment, near strut tower)
Engine controls system
Engine cooling fan relay
Evap temp
Evaporator thermistor (behind right side of dash)
Fuse box
G102 (left front of engine compt)
G103 (right front of engine compt)
G201 (left kick panel)
G202 (center of dash)
Ground
Heater fuse 20a
Hot at all times
Hot in on
Hot in on or start
Idle up
Idle-up
Ig-coil fuse 15a
Ign
Junction block
Off
Pnk
Powertrain control module (pcm) (behind right side of dash, near glove box)
Radiator fan motor
Rdtr fuse 30a
Relay box
Relay ctrl
S122 (main harn, at relay box)
S123 (main harn, 4 cm from ignition control module breakout)
S134 (a/c jumper harn, right front of engine compartment)
S210
S213
S231 (main harn, 8 cm from junction block connector c6 breakout)
S232 (i/p harn, center of dash)
S233
S238 (i/p harness, 3 cm from blower motor breakout)
S247 (main harn, 18 cm from left firewall grommet)
S254
Sensor ground

ANTI-LOCK BRAKES

Anti-lock Brake Wiring Diagrams for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Anti-lock Brake Wiring Diagrams for Chevrolet Metro 1999:

(i/p harn, 1 cm from cluster breakout) s249
(left kick panel) g200
(main harn, 20 cm from bulkhead grommet) s223
A10
A11
A12
Abs active
Abs active ind
Abs control module (left side of dash)
Abs enable
Abs fuse 40a
Abs ind
Abs motor pack assembly
B10
B11
B12
Battery feed
Brake ind
Brake ind ctrl
Brake signal
Data link connector on board diagnostics ii (upper left side of dash)
Def fuse 20a
Electronic brake control relay (in relay box)
Fuse box
G100 (left front of engine compt)
Ground
Hazard fuse 15a
Hot at all times
Hot in on
Hot in on or start
Ig-coil fuse 15a
Ignition power
Instrument cluster
Junction block
Lamp driver relay (left side of dash)
Lamp drvr rly
Left front speed sensor
Left rear speed sensor
Lf motor
Lf solenoid
Lft frt motor
Lft frt sens in
Lft frt sol out
Lft rr sens in
Pnk
Rear motor
Rf motor
Rf solenoid
Right front speed sensor
Right rear speed sensor
Rt frt motor
Rt frt sens in
Rt frt sol out
Rt rr sens in
S124 (main harn, 5 cm from front abs solenoids breakout)
S206 (main harn, 22 cm from stop lamp switch breakout)
S208
S215
S242
S251 (main harn, 5 cm from bulkhead grommet)
Serial data
Stop fuse 15a
Stop lamp switch (top of brake pedal switch)
Switched batt

COMPUTER DATA LINES

Computer Data Lines for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Computer Data Lines for Chevrolet Metro 1999:

(center rear of engine, on intake manifold)
Data link connector- (dlc) obd ii (under left side of dash, by center console)
Dome fuse 15a
Electronic brake control module (ebcm) (behind left side of dash, above junction block)
G131
G202 (left side of dash)
Hot at all times
Inflatable restraint sensing & diagnostic module (sdm) (behind center console, forward of manual selector lever)
Junction block
Powertrain control module (pcm) (behind right side of dash, near glove box)
S222
S240
S245
S249 (i/p harness, approx 1 cm from instrument cluster connector breakout)

COOLING FAN

Cooling Fan Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Cooling Fan Wiring Diagram for Chevrolet Metro 1999:

(a/c jumper harn, right front of engine compt)
(left front of engine compt)
(main harn, 18 cm from left firewall grommet)
(main harn, at relay box) s122
(right front of engine compt)
A/c 1 relay
A/c 2 relay
A/c compressor clutch
A/c compressor control module (below right side of dash, on evaporator case)
A/c condenser fan motor
A/c fuse 15a
A/c relay
Engine cooling fan relay
Fuse box
G102
G102 (left front of engine compt)
G103
Hot at all times
Hot in on junction block
Hot in on or start
Htr fuse 20a
Ig fuse 15a
Pnk
Powertrain control module (behind right side of dash, near glove box)
Radiator fan motor
Rdtr fuse 30a
Relay box
Relay ctrl
S123 (main harn, 4 cm from left firewall grommet)
S134
S213
S231 (main harn, near junction block conn c6 breakout)
S247

DEFOGGERS

Defogger Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Defogger Wiring Diagram for Chevrolet Metro 1999:

(2-door) (left side of hatch- back door, behind trim panel)
(i/p harn, behind left end of dash)
C406
Def fuse 30a
Engine controls system
G202
G411
G413 (4-door) (behind right rear quarter trim panel)
Hot in on
I/p cluster assembly
Interior lights system
Junction block (left side of dash)
Junction block (on left side of dash)
Not used
Off
Rear defogger switch
Rear defogger
Rear defogger indicator
S236
S239

ENGINE PERFORMANCE

1.0L

1.0L VIN 6, Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for 1.0L VIN 6, Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Metro 1999:

(center rear of engine) g115
(center rear of engine, on intake manifold)
(engine harn, left rear of engine compt)
(engine harness, near center of firewall)
(main harness, left side of engine compt)
(main harness, near junction block)
A/c cut-out
A/c system
Air conditioning system
Camshaft position (cmp) sensor
Ckp sensor
Cmp sensor
Cooling fans
Crankshaft position (ckp) sensor (bottom of engine, near crankshaft pulley)
Data link connector on board diagnostics ii (dlc-obd ii) (left side of dash)
Defogger system
Diag request sig
Diode module (behind center of dash)
Distributor (left side of engine)
Distributor cap
Dome fuse 15a
Duty check data link connector (behind right side of dash)
Early fuel evaporative (efe) heater (between intake manifold & red
Early fuel evaporative heater relay (ptc htr)
Ecm ground
Ect input
Efe on sig
Egr bypass cntrl
Egr sol cntrl
Engine start sig
Evap canister tank pressure control solenoid vacuum valve (top of fuel tank)
Evap canister vent solenoid valve (top of fuel tank)
Evap cann cntrl
Evap cvsv ctrl
Evap tpcsvv ctrl
Fuel level
Fuel pres
Fuel pump relay
Fuel tank pressure sensor (in fuel tank)
Fuse box (left of engine compt, behind battery)
G115
G115 (center rear of engine, on intake manifold)
Ground
Ho2s1 heater
Ho2s1 input
Ho2s2 heater
Ho2s2 input
Hot at all times
Iat input
Idle switch sig
Idle-up sig
Ign coil control
Ign pwr input
Ign trigger sig
Ignition
Ignition coil (left side of firewall)
Ignition control module (left side of firewall)
Inj control
Input ign trig
Instrument cluster system
Instrument cluster system (tachometer)
Interior lights system
Isc motor cntrl
Isca relay cntrl
Junction block (behind left side of dash)
Map input
Memory power
Mil ind control
Nca
Noise suppressor filter (left rear of firewall)
Pcm ground
Pnk
Powertrain control module (pcm) (behind right side of dash)
Ptc fuse 30a
Ptc relay cntrl
Rad fan relay
Red
Ref voltage
Relay box (left of engine compt, behind battery)
Relay control
S110
S111
S130
S167
S170
S200
S248
S261
S262
Sensor ground
Serial data out
Starting system
Tach sig
Test sw sig
Throttle body)
To spark plugs
Tp input
Upshift ind cntrl
Vss input

1.0L VIN 6, Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for 1.0L VIN 6, Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Metro 1999:

(attached to air cleaner housing)
(center rear of engine compt, on intake manifold)
(engine harn, 4 cm from egr sv valve breakout)
(engine harn, near center of firewall)
(engine harness, right rear of engine compt)
(main harn, 23 cm from map sensor breakout)
(main harn, 28 cm from front wiper motor breakout)
(main harness,
(main harness, center rear of eng compt)
(main harness, left side of engine compt)
(main harness, right rear of eng compt)
(near deck lid striker) g407
(rear of engine, in thermostat housing)
Behind battery)
Closed at idle
Egr bypass valve (top rear of engine)
Egr solenoid vacuum (egr sv) valve (top rear of engine)
Engine coolant temperature (ect) sensor
Evaporative canister purge valve (on intake manifold)
Fi fuse 15a c1
Fuel injector (in throttle body)
Fuel injector resistor (left side of firewall)
Fuel pump
Fuel pump relay
Fuel sender assembly (in fuel tank)
Fuse box (left of eng compt, behind battery)
G115
Heated oxygen sensor 1 (ho2s) (on exhaust manifold)
Heated oxygen sensor 2 (ho2s) (after 3-way catalytic converter)
Hot at all times
Hot in on or start
Idle speed control (isc) motor (top of engine, on throttle body)
Ig-coil fuse 15a
Instrument panel cluster assembly
Intake air temperature (iat) sensor
Isc relay
Junction block (behind left side of dash)
Main relay
Malfunction indicator
Manifold absolute pressure (map) sensor (on right side of firewall)
Nca
Pnk
Red
Relay box (left of eng compt, behind battery)
Relay box (left of engine compt,
Right rear of eng compt)
S101
S118
S119
S120
S126
S129
S131
S148
S151
S152
S153
S156
S168
S169
S257
S315
S316
Throttle position (tp) sensor (on throttle body)
Upshift indicator (m/t only)
Vehicle speed sensor (vss)

1.3L

1.3L VIN 9, Engine Performance Wiring Diagrams (1 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for 1.3L VIN 9, Engine Performance Wiring Diagrams (1 of 3) for Chevrolet Metro 1999:

(engine harn, 7 cm from injector 1)
(engine harn, near center of firewall)
(engine harn, right rear of engine compt)
(fuel tank harn, below right rear seat)
(main harn, 50 cm from wiper motor breakout)
A/t
Acc
Camshaft position sensor (near ignition coil 2)
Clutch pedal position switch (above clutch pedal)
Cooling fans system
Crankshaft position (ckp) sensor (bottom of engine, by crankshaft pulley)
Dome fuse 15a
Ecm ground
Ect input
Engine start sig
Evap can cntrl
Evap can vent
Evap canister purge valve (on intake manifold)
Evap canister vent solenoid (top of fuel tank)
Evap tank pres
Evap tank pressure control solenoid valve (top of fuel tank)
Fuel injectors
Fuel pump relay
G115 (center rear of engine)
Generator
Ground
Ho2s1 heater
Ho2s1 input
Ho2s2 heater
Hot at all times
Iat input
Ign pwr input
Ign ref
Ign trigger 1-4
Ign trigger 2-3
Ignition coil 1 (on cylinder head)
Ignition coil 2 (on cylinder head)
Ignition switch
Inj 1 ctrl
Inj 2 ctrl
Inj 3 ctrl
Inj 4 ctrl
Junction block (behind left side of dash)
Junction block (on left side of dash)
Lock
M/t
Map input
Memory power
Mil ind control
Nca
Pcm ground
Pnk
Powertrain control module (pcm) (behind right side of dash)
Pwr steer press
Rad fan relay
Red
Ref voltage
Relay control
Run
S119
S127 (engine harn, front of engine)
S130
S159
S160
S161
S165
S166
S248
S262
S263
S316
Sensor ground
Shift sol a
Shift sol b
Solid state
Spark plugs
Start
Starting/ charging system
Tp input
Trans- axle range switch (on trans- axle)
Vss

1.3L VIN 9, Engine Performance Wiring Diagrams (2 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for 1.3L VIN 9, Engine Performance Wiring Diagrams (2 of 3) for Chevrolet Metro 1999:

(dash harn, 3 cm from cluster connector breakout)
(engine harn, near center of firewall)
(left of eng compt, behind battery)
2nd brake solenoid (attached to valve body)
Back fuse 15a
Direct clutch solenoid (attached to valve body)
Fi fuse 15a c1
Fuel level sensor
Fuel pump
Fuel pump relay
Fuel sender assembly (in fuel tank)
Fuel tank pressure sensor (in fuel tank)
Fuse box
G407 (center rear of trunk)
Hot at all times
Hot in on or start
Instrument cluster system
Junction block (behind left side of dash)
Main relay
Manifold absolute pressure (map) sensor (on intake plenum)
N d
Pnk
Power steering pressure switch (on power steering pump)
Red
Relay box (left side of engine compartment)
S129 (engine harn, right rear of engine compt)
S151
S154
S158
S226
S259
S315
Transaxle range switch (top of transaxle)
Vehicle speed sensor (vss) (top of transaxle)

1.3L VIN 9, Engine Performance Wiring Diagrams (3 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for 1.3L VIN 9, Engine Performance Wiring Diagrams (3 of 3) for Chevrolet Metro 1999:

(center rear of engine) g115
(engine harn, 8 cm from map sensor breakout)
(engine harn, near center of firewall)
(not used)
2 pos sig
A/c cut
A/c idle up
A/c system
D pos sig
Data link connector on board diagnostics ii (dlc-obdii) (left side of dash)
Defogger system
Diode module (behind center of dash)
Engine coolant temperature (ect) sensor (rear of engine, in thermostat housing)
Ft pres
Fuel lev
G115 (center rear of engine)
Heated oxygen sensor 1 (ho2s) (on exhaust manifold)
Heated oxygen sensor 2 (ho2s) (after 3-way catalytic converter)
Ho2s 2 sig
Hot in on or start
Iac valve
Idle air control valve (top of engine, on throtle body)
Idle up
Ig-coil fuse 15a
Ignition
Instrument cluster system
Instrument panel cluster assembly
Intake air temperature (iat) sensor (attached to air cleaner housing)
Interior
Junction block (behind left side of dash)
L pos sig
Lights system
Malfunction indicator
N pos sig
Nca
Not used
P pos sig
Pnk
Powertrain control module (behind right side of dash)
R pos sig
Red
S101
S126
S130
S131 (engine harn, 9cm from generator breakout)
S152
S153
S156
S163 (engine harn, 2 cm from injector breakout)
S164
S242
S248
S263
Sensor gnd
Serial data
Tach
Throttle position (tp) sensor (on side of throttle body)
Upshift ind
Upshift indicator (m/t only)
Vehicle speed sensor (vss) (m/t)

EXTERIOR LIGHTS

Back-up Lamps Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Back-up Lamps Wiring Diagram for Chevrolet Metro 1999:

(2-door) s402 (4 door) s407
(eng harn, 9 cm from left engine compt grommet)
(floor harness, 13 cm from g407 breakout (2-door), floor harn, 27 cm from left rear combination lamp connector breakout (4 door))
A/t
Back fuse 15a
Back-up lamp
Back-up lamp switch (top of transaxle)
G407 (near deck lid striker)
Hot in on & start
Junction block
Left rear combination lamp
M/t
Red
Red red
Right rear combination lamp
S154 red
S401
S411
S413
Transaxle range switch (top of transaxle)
Transmissions system

Exterior Lamps Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Exterior Lamps Wiring Diagram for Chevrolet Metro 1999:

(2 door)
(a/t)
(center of hatchback door, near rear wiper motor) g410
(floor harness, approx 13-34 cm from left rear combination lamp conn breakout)
(floor harness, approx 36 cm from hatchback door harness breakout (2-door), floor harness, approx 39cm from left rear combination lamp connector breakout (4-door)) s400
(floor harness, approx 8 cm from g407 breakout (2-door), floor harness, approx 10 cm from luggage compt lamp switch connector breakout (4-door))
(left rear comb lamp pigtail)
(left side of dash) junction block
(m/t)
(main harn, 8 cm from g200)
(main harness, approx 22 cm from stoplamp switch connector breakout)
(main harness, approx 8 cm from junction block conn breakout)
(right rear comb lamp pigtail)
2 door
4 door
Anti-lock brakes system
Back fuse 15a
Center high- mounted stoplamp
Combination switch
G100 (lh front engine compt, on left front inner fender near battery)
G101 (right front inner fender)
G101)
G202
G202 (left side of dash)
G202 (under left side of dash)
G407 (near deck lid striker)
G407 (rear center of luggage compt, near deck lid striker)
Haz fuse 15a
Hazard switch
Head
Hot at all times
Hot in on & start
Instrument panel cluster assembly
Interior lights system
Junction block
Junction block (behind left side of dash)
Left front park/turn lamp
Left parking lamp
Left rear combination lamp
Left stop lamp
Left turn ind
License plate lamp
Light 1 relay (relay box)
Light switch
Off
Park
Right front park/turn lamp
Right parking lamp
Right rear combination lamp
Right stop lamp
Right turn ind
S100
S102
S113
S117
S204
S206
S240
S256
S302 (floor harness, approx 10 cm from 14 pin conn, behind left side of dash)
S403 (2-door) s406 (4-door)
S404
S405
S408
S410 (2 door)
S411
S412
S413
Side marker lamp (2 door)
Stop fuse 15a
Stoplamp switch (top of brake pedal bracket)
Tail fuse 15a
Tail/ stop lamp
Turn lamp
Turn relay
Turn signal switch

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Ground Distribution Wiring Diagram (1 of 3) for Chevrolet Metro 1999:

c1
(main harness, approx 8cm from bulkhead grommet, near master cylinder)
(with abs) lamp driver relay
A/c 2 relay (condenser
A/c compressor control module
Battery
Braid
Brake fluid level switch
Camshaft position sensor
Crankshaft position sensor shield
D c2
Daytime running lamps control module
Distributor shield
Electronic brake control module
Engine cooling fan motor
Fan)
Front washer pump
G100 (lh front engine compartment, on lh front inner fender near battery)
G108 (lh front engine compartment, front of battery)
G130 (mounted on top lh side of transaxle)
G131 (center rear of engine, on intake manifold)
G200 (behind left kick panel)
Heated oxygen sensor 1 shield
Heated oxygen sensor 2 shield
Horn
Idle air control valve (vin 9)
Idle speed control motor
Ignition coil no 1 (vin 9)
Ignition coil no 2 (vin 9)
Left front park/turn lamp
Left parking lamp
Light 2 relay
Powertrain control module
Rear washer pump
Relay box
S113 (main harness, approx 6cm from left front turn lamp connector breakout)
S115 (main harness, near rear washer pump)
S130 (engine harness, near generator connector breakout)
S165 (engine harn, near starter breakout)
S207 (main harness, approx 15cm from g200)
S208 (main harness, 2cm from junction block connector c8 breakout)
S209
S210 (main harness, left side of dash)
S213 (main harn, near master cylinder)
S247 (main harness, left rear of engine compt)
S248 (engine harn, at pcm branch breakout)
S263 (engine harn, at pcm branch breakout)
To j/b (diagram 2 of 3)
To s111 (diagram 2 of 3)
Vin 9
W/ abs

Ground Distribution Wiring Diagram (2 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Ground Distribution Wiring Diagram (2 of 3) for Chevrolet Metro 1999:

(4-door)
(i/p harness, approx 5cm from cigar lighter connector breakout) s243
(not used)
(with a/c) a/c switch
A/c condenser fan
Audio alarm module
Blower motor
C210
Center high mounted stop lamp
Cigar lighter
Combination switch
Data link connector on-board diagnostic ii
Data link connector- on-board diagnostic ii
Dimmer switch
Dome lamp
Dual pressure switch
Early fuel evaporation heater
From g131 (diagram 1 of 3)
From s209 (diagram 1 of 3)
Front wiper/ washer switch
G101 (rh front engine compartment, on right front inner fender)
G131 (center rear of engine)
G202 (left side of dash)
G206 (right center of dash, behind radio)
G410 (2-door) (center of hatchback door, near rear wiper motor)
Ignition control module
Ignition switch
Illumination controller
Instrument panel cluster assembly
Junction block
Left power door lock switch
Light switch
Noise suppressor filter
Power door lock control module
Radio
Rear defogger switch
Rear wiper motor
Red
Right front park/turn lamp
Right parking lamp
Right power door lock switch
S111 (main harness, near ignition coil connector breakout)
S117 (main harn, near g101 breakout)
S134 (engine harn, 22cm from bulkhead grommet, center of firewall)
S235 (i/p harness, left side of dash)
S236 (i/p harness, 8cm from i/p cluster c3 breakout)
S237 (i/p harness, 10cm from radio conn breakout)
S238 (i/p harn, near blower motor breakout)
S239 (i/p harness, approx 11cm from i/p cluster c3 breakout)
S240 (i/p harness, approx 6cm from dlc-obd ii breakout)
S245 (i/p harn, 12cm from dash cluster breakout)
S254 (i/p harness, center of dash)
S314 (floor harn, left side of dash)
Turn relay
Vin

Ground Distribution Wiring Diagram (3 of 3) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Ground Distribution Wiring Diagram (3 of 3) for Chevrolet Metro 1999:

(floor harness, approx 20cm from center console branch breakout) s301
(floor harness, approx 20cm from left rear combination lamp conn breakout) s407
(floor harness, approx 5cm from left rear combination lamp connector breakout) s402
2 door
4 door
Below right rear seat)
Center high mounted stop lamp
Fuel sender assembly
G203 (behind right kick panel)
G407 (rear center of lug- gage compartment, near deck lid striker)
G411 (2-door) (left side of hatch- back door, behind trim panel)
G413 (4-door) (behind right rear quarter trim panel)
Inflatable restraint forward discriminating sensor
Left rear combination lamp
License plate lamp
Rear defogger
Red
Right rear combination lamp
S311 (floor harness, approx 10cm from breakout to luggage compartment harness)
S315 (fuel tank jumper harness,
S403 (floor harness, approx 5cm from g407 breakout)
S406 (floor harness, approx 10cm from left rear combination lamp connector breakout)
S408 (floor harness)
S411 (right rear combination lamp pigtail, approx 6cm from grommet at right rear of trunk)
S413 (left rear combination lamp pigtail, approx 6cm from grommet at left rear of trunk)
Seat belt switch
Sensing and diagnostic module
Shift lock solenoid
Under right rear seat)

HEADLIGHTS

Headlight Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Headlight Wiring Diagram for Chevrolet Metro 1999:

(main harn, approx 22 cm from grommet at left rear of eng compt) s107
(main harn, approx 13 cm from brake fluid level switch breakout) s104
Anti-lock brakes systems
Brake ind
C5 red
Charge in
Combination switch
Daytime running lamps control module (behind left side of dash)
Daytime running lamps diode
Daytime running lamps ind
Dimmer switch
Drl indic
G200 (behind left kick panel)
G202 (left side of dash)
Ground
H/l, l fuse 15a
H/l, r fuse 15a
Hdlmps on in
Head
High beam ind
Hot at all times
Hot in on & start
Ig-coil fuse 15a
Ignition
Instrument panel cluster assembly
Junction block (left side of dash)
Left headlamp
Light 2 relay
Light switch
Low beam
Off
Park
Park brake
Parking brake switch
Pass
Red
Relay box (on left side of engine compt, behind battery)
Right headlamp
S105 (main harn, approx 6 cm from relay box breakout)
S202
S205 (main harn, approx 1 cm from grommet at left rear of engine compt)
S207
S210
S223 (main harn, approx 10 cm from grommet at left rear of engine compt)
S242
S248
Starting/ charging system

HORN

Horn Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Horn Wiring Diagram for Chevrolet Metro 1999:

Contact coil
G100 (left front side of engine compt, near battery)
G202 (under driver's inflator module)
Haz fuse 15a
Horn (left front side of engine compt)
Horn relay
Hot at all times
Junction block (on left side of dash)
Left horn switch
Right horn switch
S113
Turn signal/ combination switch

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Instrument Cluster Wiring Diagram for Chevrolet Metro 1999:

(1.0l)
(1.3l)
(center rear of engine, on intake manifold)
A/t
A10
A11
A12
A13
A14
A15
A16
A16 c1
Abs active ind
Abs ind
Accy
Air bag ind
Anti-lock brakes system
B10
B10 c2
Brake fluid level switch (in brake fluid reservoir)
Brake ind
C1 b5
C10
C11
C12
C13
C13 c3
Charge ind
Ctrl
Daytime running lamps control module (behind left side of dash)
Defogger ind
Defogger system
Drl ind
Electronic brake control module (behind left side of dash, above junction block)
Engine controls system
Engine coolant temperature gauge
Engine coolant temperature sensor (on rear of engine, in thermostat housing)
Exterior lights system
Fuel gauge
Fuel lvl sig
Fuel sender assembly (in fuel tank)
G100 (lh front engine compt, on lh front inner fender, near battery)
G131
G202 (left side of dash)
G407 (rear center of luggage compt, near deck lid striker)
Headlights system
High beam ind
Hot in on & start
Ig-coil fuse 15a
Ignition switch
Illumination (2 bulbs)
Ind ctrl
Instrument panel cluster assembly
Interior lights system
Junction block
Junction block (on left side of dash)
Left turn ind
Lock
M/t
Malfunction ind
Oil pressure ind
Oil pressure switch (left side of engine, behind exhaust manifold)
Parking brake switch (under floor console, on parking brake lever base)
Powertrain control module (behind right side of dash, near glove box)
Red
Right turn ind
S213
S223 (main harn, approx 10 cm from gromet at bulkhead connector)
S226 (dash harn, approx 3 cm from cluster connector c3 breakout)
S240
S242
S245
S315
Seat belt ind
Signal
Start
Starting/charging system
Tachometer
Upshift ind (w/m/t)
Vehicle speed sensor
Vehicle speed sensor (on top of transaxle)
Vss hi
Vss lo
Warning system

INTERIOR LIGHTS

Interior Light Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Interior Light Wiring Diagram for Chevrolet Metro 1999:

(4-door)
(i/p harn, behind left side of dash) s217
(i/p harness, approx 4 cm from data link connector- on board diagnostics ii breakout) s252
(i/p harness, approx 6 cm from diode module connector breakout)
(left side of dash) junction block
(main harness, approx 2 cm from bulkhead grommet near master cylinder) s204
(not used)
2-door
Audio alarm module (behind dash, left of steering column)
Bulbs
Combination switch
Diode module (behind center of dash, taped to harness)
Dome fuse 15a
Dome lamp
Door
Engine controls system
Exterior lights system
G202
G206 (right side of dash, behind radio)
Ground
Head
Heater control unit illumination lamp
Hot at all times
Illumination controller
Instrument panel cluster assembly
Junction block (behind left side of dash)
Junction block (on left side of dash)
Left front door jamb switch
Light 1 relay
Light switch
Luggage compartment lamp
Luggage compartment lamp switch
Manual selector lever illumination lamp (a/t)
Off
Park
Power
Radio
Rear defogger switch
Rear wiper/ washer switch
Relay box (on left side of engine compartment, behind battery)
S218 (i/p harness, approx 3 cm from i/p cluster c3 breakout)
S219 (i/p harn, behind left side of dash)
S221 (i/p harness, approx 7 cm from i/p cluster c2 breakout)
S222
S228 (i/p harness, behind left side of dash)
S229 (i/p harness, approx 4 cm from i/p cluster c1 breakout)
S230 (i/p harness, 13 cm from i/p cluster c3 breakout)
S239
S254
S302 (floor harn, behind left side of dash)
S310 (floor harness, approx 6 cm from junction block conn breakout)
S419 (floor harness, approx 21 cm from right rear door jamb sw conn breakout)
Solid state
Tail fuse 15a
Warning systems

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 2) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Power Distribution Wiring Diagram (1 of 2) for Chevrolet Metro 1999:

(m/t) (a/t)
(main harness, approx 5cm from relay box breakout) s151
(main harness, at relay box) s122
(main harness, left side of dash) s258
(main harness, near master cylinder) s244
(main harness, near master cylinder) s248
(not used)
A/c 1 relay
A/c 2 relay
A/c fuse 15a
Abs fuse 40a
B12
Bat
Batt fuse 70a
Battery
Data link connector- on-board diagonstics ii
Daytime running lamps diode
Dome fuse 15a
Dome lamp
Door lock fuse 20a
Efe htr relay
Electronic brake control module
Electronic brake control relay
Fi fuse 15a
Fuse box (left side of engine compt, behind battery)
Generator
Haz fuse 15a
Hazard switch
Hl-l fuse 15a
Hl-r fuse 15a
Horn relay
Ig fuse 60a
Ignition key warning switch
Instrument panel cluster assembly
Junction block (left side of dash)
Lamp fuse 40a
Left headlamp
Light 1 relay
Luggage compartment lamp
Main relay
Power door lock control module
Powertrain control module
Ptc fuse 30a
Radio
Rdtr fan relay
Rdtr fuse 30a
Relay box
Relay box (left side of engine compt, behind battery)
Right headlamp
S222 (i/p harness, approx 6cm from dlc breakout)
Starter solenoid
Stop fuse 15a
Stoplamp switch
Tail fuse 15a
To ignition switch (diagram 2 of 2)
Turn signal/ combination switch

Power Distribution Wiring Diagram (2 of 2) for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Power Distribution Wiring Diagram (2 of 2) for Chevrolet Metro 1999:

(engine harn, center of firewall) s126
(engine harn, near generator breakout)
(i/p harn, approx 6cm from dlc breakout) s224
(i/p harness, 5cm from cluster conn breakout) s241
(i/p harness, at cluster conn breakout) s242
(main harn, 8cm from junction block breakout) s282
(main harn, center of firewall) s152
(main harness, approx 10cm from breakout to i/p harn) s215
(main harness, near master cylinder) s101
A/c 1 relay
A/c amplifier
A/t
Acc
Acc fuse 15a
Air bag fuse 15a
Audio alarm module
Back fuse 15a
Back-up lamp switch (m/t) transaxle range switch (a/t)
Blower speed selector switch
Camshaft position sensor (vin 9)
Cigar lighter
Clutch pedal position switch
Daytime running lamps control module
Def fuse 30a
Electronic brake control module
Electronic brake control relay
Engine cooling fan relay
From junction block (diagram 1 of 2)
Front wiper motor
Front wiper/ washer switch
Fuel pump relay
G206 (right center of dash, behind radio)
Generator
Hazard switch
Heated oxygen sensor 1
Heated oxygen sensor 2
Htr fuse 30a
Ig-coil fuse 15a
Ignition coil (vin 6)
Ignition coil 1 (vin 9)
Ignition coil 2 (vin 9)
Ignition switch
Instrument panel cluster assembly
Junction block (left side of dash)
Lamp driver relay
Lock
M/t
Noise suppressor filter (vin 6)
Powertrain control module
Radio
Rear defogger switch
Rear wiper motor
Rear wiper/ washer switch
Relay box (left side of engine compt, behind battery)
Run
S160
S161
S231 (main harn, near master cylinder)
Sensing & diagnostics module
Start
Transaxle range switch
Turn/ signal combination switch
Wiper fuse 15a

POWER DOOR LOCKS

Power Door Lock Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Power Door Lock Wiring Diagram for Chevrolet Metro 1999:

(floor harness, approx 11cm from breakout to right front door)
Door lock fuse 20a
G202
Ground
Hot at all times
Junction block (left side of dash)
Left front power door lock actuator
Left front power door lock switch
Left rear power door lock actuator
Lock
Lock in
Lock out
Pnk
Power
Power door lock control module (behind left side of dash on "a" pillar)
Red
Right front power door lock actuator
Right front power door lock switch
Right rear power door lock actuator
S307
S308 (floor harn, approx 19cm from breakout to right front door)
S314
Unlock
Unlock in
Unlock out

RADIO

Radio Wiring Diagrams for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Radio Wiring Diagrams for Chevrolet Metro 1999:

Acc fuse 15a
Antenna
Dome fuse 15a
G206 (right center of dash, behind radio)
Ground
Hot at all times
Hot in acc or run
Interior lights system
Junction block (on left side of dash)
Lcd dim cntrl
Lcd input
Left front speaker
Left rear speaker
Lf speaker (+)
Lf speaker (-)
Lr speaker (+)
Lr speaker (-)
Memory power
Nca
Radio
Radio power
Red
Rf speaker (+)
Rf speaker (-)
Right front speaker
Right rear speaker
Rr speaker (+)
Rr speaker (-)
S222
S224
S237

SHIFT INTERLOCKS

Shift Interlock Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Shift Interlock Wiring Diagram for Chevrolet Metro 1999:

(rear center of luggage compt, near deck lid striker)
2 door
4 door
Back fuse 15a
Engine controls system
G407
Hot in on & start
Junction block (behind left side of dash)
S158 (engine harn, near generator)
S301
S311
Shift lock solenoid (under floor console, in front of shift lever)
Stoplamp switch (top of brake support)
Transaxle range switch (top of transaxle)

STARTING/CHARGING

Charging Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Charging Wiring Diagram for Chevrolet Metro 1999:

(1997)
(1998, 99)
(engine harn, 10 cm from bulkhead grommet) s162
Acc
Batt fuse 70a
Battery
Charge indicator
Daytime running lamps control module (behind left side of dash)
Fuse box (left side of engine compt, behind battery)
G108 (left front of engine compt, front of battery)
G130 (top left side of transaxle)
Generator
Ig fuse 60a
Ig-coil fuse 15a
Ignition switch
Instrument panel cluster assembly
Junction block (left side of dash)
Lock
Run
S160
S203 (1cm from bulkhead grommet)
S242
Start
Starter solenoid

Starting Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Starting Wiring Diagram for Chevrolet Metro 1999:

A/t
Acc
Batt fuse 70a
Battery
Clutch pedal position switch (above clutch pedal)
Engine controls system
Fuse box (left side of engine compt, behind battery)
G108 (left front of engine compt, front of battery)
G130 (top left side of transaxle)
Ig fuse 60a
Ignition switch
Junction block (left side of dash)
Lock
M/t
S127 (engine harn, approx 8cm from breakout to starter solenoid)
Start
Starter
Starter solenoid
Transaxle range switch (top of transaxle)

SUPPLEMENTAL RESTRAINTS

Supplemental Restraint Wiring Diagram for Chevrolet Metro 1999

Get access to all wiring diagrams of the car

List of elements for Supplemental Restraint Wiring Diagram for Chevrolet Metro 1999:

(center rear of luggage compt)
(floor harn, near console branch breakout-2 door, near breakout to trunk harness-4 door)
(i/p harn, near breakout to c200, left side of dash) s227
(i/p harn, near breakout to cluster)
Air bag fuse 15a
Airbag indicator
Data line
Data link connector (dlc) obd-ii (under left side of dash)
Discrim sens
Driver high
Driver low
G203 (right kick panel)
G407
Ground
Hot in on or start
Ig-coil fuse 15a
Ign pos volt
Ind ctrl
Inflatable restraint forward discriminating sensor (behind hood latch assembly)
Inflatable restraint i/p module (above glove box)
Inflatable restraint sensing and diagnostic module (sdm) (behind center console)
Inflatable restraint steering wheel module (center of steering wheel)
Instrument panel cluster assembly
Junction block (left side of dash)
Nca
Pass high
Pass low
Red
S242 (i/p harn, at cluster conn breakout)
S249
S301 (2 door) s311 (4 door)
Seat belt switch
Shorting bar
Sir contact coil (part of turn signal/ combination switch)
Sir data line
Sir data link connector (behind left side of dash)
St belt sw
Warning systems