ENGINE PERFORMANCE
4.6L
4.6L CNG, Engine Performance Wiring Diagrams (1 of 5) for Ford Crown Victoria S 1998
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for 4.6L CNG, Engine Performance Wiring Diagrams (1 of 5) for Ford Crown Victoria S 1998:
- (behind right kick panel) g203
- (left side of engine, on left side of engine coil) radio noise capacitor
- (near breakout to 4-pin conn at right front fender)
- (near breakout to camshaft position sensor)
- (near breakout to generator)
- (rear of left front fender apron)
- A/c cycling
- Case gnd
- Ckp (+)
- Ckp (-)
- Coil 1
- Coil 3
- Coil 5
- Coil 6
- Cooling fans (fan high rly)
- Cooling fans (fan low relay)
- Crankshaft position sensor (lower right front of engine)
- Crankshaft position sensor shield
- Cyl temp ind
- Data link (+)
- Data link (-)
- Data link connector (left side of dash)
- Ect ind
- Egr vac reg
- Egr vacuum regulator solenoid (top center rear of engine)
- Engine compartment fuse box (right front of engine compt)
- Eprom
- Fan high rly
- Fan low rly
- Fuel sol vlv
- Fuse 15a
- Fuse 25a
- Fuse 30a
- G104
- G104 (rear of left front fender apron)
- Hot at all times
- Hot in run or start
- I/p fuse panel (below dash, left of steering column)
- Iat sens
- Ignition coils
- Intake air temperature sensor (left front of engine compt)
- Maf sig rtn
- Mil
- Nca
- Pcm power diode
- Pcm power relay
- Powertrain control module (behind left side of dash, on left side of firewall)
- Pwr gnd
- Red
- Relay center (left side of engine compt)
- Rt ho2s #2
- S100
- S101
- S103
- S119
- S134
- S135
- S151
- S223
- S276
- Shft sol 1
- Shft sol 2
- Tcil
- Tr1
- Tr2
- Tr4
- Trans ctrl sw
- Trans temp
- Transmission control switch (bottom of steering column)
- Vss (-)
4.6L CNG, Engine Performance Wiring Diagrams (2 of 5) for Ford Crown Victoria S 1998
List of elements for 4.6L CNG, Engine Performance Wiring Diagrams (2 of 5) for Ford Crown Victoria S 1998:
- 4r7ow transmission
- C250
- C251
- Cylinder head temp input
- Digital transmission range sensor (dtr sensor) (left side of transmission)
- Electronic pressure control solenoid
- Engine coolant temp input
- Engine coolant temperature sensor (top right front of engine)
- Fuel display input
- G104 (rear of left front fender apron)
- G203 (behind right kick panel)
- Inst cluster ground
- Instrument cluster
- Mal- function indicator input
- Mass air flow sensor (behind air cleaner assembly)
- Power input
- R n
- Red
- S105
- S119
- S222
- S299 (near breakout to inst cluster)
- Shift solenoids
- Ss1
- Ss2
- Torque converter clutch solenoid
- Trans control indicator input
- Transmission fluid temperature sensor
- Vehicle speed input
4.6L CNG, Engine Performance Wiring Diagrams (3 of 5) for Ford Crown Victoria S 1998
List of elements for 4.6L CNG, Engine Performance Wiring Diagrams (3 of 5) for Ford Crown Victoria S 1998:
- (at left kick panel)
- (center rear of trunk) g407
- (in trunk, on left support) inertia fuel shutoff switch
- (left side of engine compt) relay center
- (near breakout to 16-pin conn at left rear of engine compt) s130
- (near breakout to 8-pin conn at left rear of engine compt)
- (near breakout to 8-pin conn at left rear of engine compt) s148
- (near breakout to fuel pump prime conn)
- (near breakout to fuel tank sol valve no 4)
- (on fuel tank assembly) fuel tank solenoid valve no 1
- (on fuel tank assembly) fuel tank solenoid valve no 2
- (on fuel tank assembly) fuel tank solenoid valve no 3
- (on fuel tank assembly) fuel tank solenoid valve no 4
- (on top of engine, on fuel rail) fuel rail cutoff solenoid
- (rear of left front fender apron)
- A/c clutch cycling pressure switch (right rear of engine compt, on a/c accumulator)
- A/c high pressure cutout switch (right side of engine compt, near fuse box)
- Air conditioning (a/c cutout relay)
- Camshaft position sensor (left front of engine, below ignition coil)
- Engine compartment fuse box (right front of engine compt)
- Fuel valve relay
- Fuse 20a
- G104
- G104 (rear of left front fender apron)
- Hot at all times
- Left heated oxygen sensor no 2 (in exhaust, rear of catalyst)
- Nca
- Output shaft speed sensor (left side of transmission)
- Red
- Right heated oxygen sensor no 2 (in exhaust, rear of catalyst)
- S119
- S125
- S129 (near breakout to 4-pin conn at left rear of engine compt)
- S147
- S298
- S427
4.6L CNG, Engine Performance Wiring Diagrams (4 of 5) for Ford Crown Victoria S 1998
List of elements for 4.6L CNG, Engine Performance Wiring Diagrams (4 of 5) for Ford Crown Victoria S 1998:
- (at left side side of trunk)
- (near breakout to differential pressure feedback egr sensor) s143
- (near breakout to ngv module)
- (on upper fuel tank assembly) fuel tank assembly temperature sensor no 1
- (on upper fuel tank assembly) fuel tank assembly temperature sensor no 2
- (on upper fuel tank assembly) fuel tank pressure sensor
- Cooling fans (high and low speed relays)
- Data (+)
- Data (-)
- Ftp return
- Ftp sensor
- Fuel injectors
- G104 (rear of left front fender apron)
- Ground
- I/p
- Idle air control valve (left side of intake manifold)
- Ignition
- Inj no.1 in
- Inj no.1 out
- Inj no.2 in
- Inj no.2 out
- Inj no.3 in
- Inj no.3 out
- Inj no.4 in
- Inj no.4 out
- Inj no.5 in
- Inj no.5 out
- Inj no.6 in
- Inj no.6 out
- Inj no.7 in
- Inj no.7 out
- Inj no.8 in
- Inj no.8 out
- Natural gas vehicle (ngv) module (on front of radiator support)
- Power
- Red
- Red/pnk
- Ref voltage
- S131 (near breakout to fuel injector 8)
- S141
- S197
- S429
- S430
- Tan
- Tan/red
- Temp no.1
- Temp no.2
4.6L CNG, Engine Performance Wiring Diagrams (5 of 5) for Ford Crown Victoria S 1998
List of elements for 4.6L CNG, Engine Performance Wiring Diagrams (5 of 5) for Ford Crown Victoria S 1998:
- (behind right side of dash) air suspension/ evo steering module
- (behind right side of dash) electronic variable orifice steering module
- (left rear of engine compt) speed control servo assembly
- (left rear of transmission) vehicle speed sensor
- (near breakout to right h2os 1) s126
- (right side of dash) speed chime module
- (top of brake pedal support) brake pedal position switch
- A/c cutout sw
- A/c wot cutout
- Air conditioning (a/c cutout rly)
- Batt
- Brake on/off
- C204
- C214
- C216
- C234
- Cam pos in
- Cht sensor
- Coil 2
- Coil 7
- Coil 8
- Cylinder head temperature sensor (top left front of engine)
- Differential pressure feedback egr sensor (right side of intake manifold)
- Dpfe sens
- Dtr sens
- Engine compartment fuse box (right front of engine compt)
- Engine fuel temperature sensor (on top of engine)
- Epc sol
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuel pump ctrl
- Fuel temp
- Fuse 15a
- Fuse 30a
- G104 (rear of left front fender apron)
- G203 (behind right kick panel)
- Heater ctrl
- Hot at all times
- I/p fuse panel (below dash, left of steering column)
- I/p sensor
- Iac sol
- Injection pressure sensor (on top of engine)
- L ho2s
- Left heated oxygen sensor no 1 (lower left rear of engine, in exhaust manifold)
- Lft ho2s #1
- Lft ho2s #2
- Maf sens in
- Nca
- Oss (+)
- Power
- Power gnd
- Powertrain control module (behind left side of dash, on left side of firewall)
- Pwr gnd
- R ho2s
- Red
- Red/pnk
- Ref volt
- Right heated oxygen sensor no 1 (lower right rear of engine, in exhaust manifold)
- Rt ho2s #1
- S105
- S109 (near breakout to 16-pin conn at left rear of engine compt)
- S119
- S123 (near breakout to fuel injector 8)
- S247 (near breakout to front control unit)
- S258
- S265
- Sig rtn
- Tan
- Tan/red
- Tcc sol
- Throttle position sensor (left side of throttle body)
- Tp sens in
- Vss (+)
- Vss (-)
- W/ air suspension & evo steering
- W/ evo steering only
4.6L, Engine Performance Wiring Diagrams (1 of 4) for Ford Crown Victoria S 1998
List of elements for 4.6L, Engine Performance Wiring Diagrams (1 of 4) for Ford Crown Victoria S 1998:
- (behind right kick panel) g203
- (left side of engine, on left side of engine coil) radio noise capacitor
- (near breakout to 4-pin conn at right front fender)
- (near breakout to camshaft position sensor)
- (rear of left front fender apron)
- A/c cutout
- Air conditioning (a/c cutout sw)
- Case gnd
- Ckp (+)
- Ckp (-)
- Coil 1
- Coil 3
- Coil 5
- Coil 6
- Cooling fans (fan high rly)
- Cooling fans (fan low relay)
- Crankshaft position sensor (lower right front of engine)
- Crankshaft position sensor shield
- Cyl temp ind
- Data link (+)
- Data link (-)
- Data link connector (left side of dash)
- Ect ind
- Egr vac reg
- Egr vacuum regulator solenoid (top center rear of engine)
- Engine compartment fuse box (right front of engine compt)
- Eprom
- Fan high rly
- Fan low rly
- Fuel flow
- Fuel gauge
- Fuel pump
- Fuse 15a
- Fuse 25a
- Fuse 30a
- G104
- G104 (rear of left front fender apron)
- Hot at all times
- Hot in run or start
- I/p fuse panel (below dash, left of steering column)
- Iat sens
- Ignition coils
- Instrument cluster
- Intake air temperature sensor (left front of engine compt)
- Maf sig rtn
- Mil
- Nca
- Pcm power diode
- Pcm power relay
- Powertrain control module (behind left side of dash, on left side of firewall)
- Pwr gnd
- Red
- Relay center (left side of engine compt)
- Rt ho2s #2
- S100
- S101
- S103
- S119
- S134
- S135 (near breakout to generator)
- S151
- S223
- S276
- Shft sol 1
- Shft sol 2
- Tcil
- Tr1
- Tr2
- Tr4
- Trans ctrl sw
- Trans temp
- Transmission control switch (bottom of steering column)
- Vss (-)
4.6L, Engine Performance Wiring Diagrams (2 of 4) for Ford Crown Victoria S 1998
List of elements for 4.6L, Engine Performance Wiring Diagrams (2 of 4) for Ford Crown Victoria S 1998:
- (near breakout to engine compt fuse box)
- (speedometer/ odometer) vehicle speed input
- 4r7ow transmission
- Analog
- C250
- C251
- C255
- C256
- Cylinder head temp input
- Differential pressure feedback egr sensor (right side of intake manifold)
- Digital
- Digital transmission range sensor (dtr sensor) (left side of transmission)
- Electronic pressure control solenoid
- Engine coolant temp input
- Engine coolant temperature sensor (top right front of engine)
- Evaporative emission canister purge valve (rear center of engine compt)
- Fuel flow rate input
- G104 (rear of left front fender apron)
- G203 (behind right kick panel)
- Instrument cluster
- Malfunction indicator input
- Mass air flow sensor (behind air cleaner assembly)
- R n
- Red
- S105
- S119
- S126 (near breakout to right htd oxy sensor 1)
- S153
- S222
- Shift solenoids
- Ss1
- Ss2
- Throttle position sensor (left side of throttle body)
- Torque converter clutch solenoid
- Transmission control indicator input
- Transmission fluid temperature sensor
4.6L, Engine Performance Wiring Diagrams (3 of 4) for Ford Crown Victoria S 1998
List of elements for 4.6L, Engine Performance Wiring Diagrams (3 of 4) for Ford Crown Victoria S 1998:
- (center rear of trunk) g407
- (in trunk, on left support) inertia fuel shutoff switch
- (near breakout to 16-pin conn at left rear of engine compt)
- (near breakout to 4-pin conn at left rear of engine compt)
- (near breakout to 8-pin conn at left rear of engine compt)
- (near breakout to 8-pin conn at left rear of engine compt) s148
- (near breakout to fuel injector 8)
- (near breakout to fuel pump prime conn)
- (top of brake pedal support) brake pedal position switch
- Air conditioning (a/c cutout relay)
- Camshaft position sensor (left front of engine, below ignition coil)
- Cooling fans (fan low relay)
- Cylinder head temperature sensor (top left front of engine)
- Engine compartment fuse box (right front of engine compt)
- Fuel pump prime connector (left sdie of engine compt)
- Fuel pump relay
- Fuel pump/ fuel gauge sender
- Fuel tank assembly
- Fuel tank pressure sensor (on upper fuel tank assembly)
- Fuse 15a
- Fuse 20a
- Hot at all times
- I/p fuse panel (below dash, left of steering column)
- Left heated oxygen sensor no 1 (lower left rear of engine, in exhaust manifold)
- Left heated oxygen sensor no 2 (in exhaust, rear of catalyst)
- Nca
- Output shaft speed sensor (left side of transmission)
- Red
- Red/pnk
- Relay center (left side of engine compt)
- Right heated oxygen sensor no 1 (lower right rear of engine, in exhaust manifold)
- Right heated oxygen sensor no 2 (in exhaust, rear of catalyst)
- S115 (near breakout to 16-pin conn at left rear of engine compt)
- S123
- S124
- S125
- S129
- S130
- S147
- S265
- S402
4.6L, Engine Performance Wiring Diagrams (4 of 4) for Ford Crown Victoria S 1998
List of elements for 4.6L, Engine Performance Wiring Diagrams (4 of 4) for Ford Crown Victoria S 1998:
- (behind right side of dash) air suspension/ evo steering module
- (behind right side of dash) electronic variable orifice steering module
- (left rear of engine compt) speed control servo assembly
- (left rear of transmission) vehicle speed sensor
- (near breakout to diff press feedback egr sensor)
- (near breakout to fuel injector 8)
- (rear of vehicle, left side of trunk) canister vent solenoid
- (right side of dash) speed chime module
- A/c cutout sw
- A/c wot cutout
- Air conditioning (a/c cutout rly)
- Air conditioning (a/c cutout sw)
- Batt
- Brake on/off
- C204
- C214
- C216
- C234
- Cam pos in
- Canp
- Cht sensor
- Coil 2
- Coil 7
- Coil 8
- Dpfe sens
- Engine compartment fuse box (right front of engine compt)
- Epc sol
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- Fuel injectors
- Fuel press
- Fuel pump ctrl
- Fuse 30a
- G104 (rear of left front fender apron)
- G203 (behind right kick panel)
- Heater ctrl
- Hot at all times
- Iac sol
- Idle air control valve (left side of intake manifold)
- L ho2s
- Lft ho2s #1
- Lft ho2s #2
- Maf sens in
- Oss (+)
- Power
- Power gnd
- Powertrain control module (behind left side of dash, on left side of firewall)
- Pwr gnd
- R ho2s
- Red
- Red/pnk
- Ref volt
- Rt ho2s #1
- S105
- S109 (near breakout to 16-pin conn at left rear of engine compt)
- S119
- S131
- S143
- S247 (near breakout to front control unit)
- Sig rtn
- Tan
- Tan/red
- Tcc sol
- Tp sens in
- Tr sens
- Vapor valve
- Vss (+)
- Vss (-)
- W/ air suspension & evo steering
- W/ evo steering only