AIR CONDITIONING
Manual A/C Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Manual A/C Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (behind instrument cluster)
- A/c ecu
- A/c switch, outside/inside air selection damper control & illumination
- A17
- A17-1
- Air thermo sensor (behind right center of dash, on hvac unit)
- Blower motor (behind right end of dash)
- Blower relay
- Blower switch
- C210
- C211
- C214
- Cooling fan motor
- Defogger system
- Fan control module (on fan shroud, at left front of engine compt)
- Fuse 30a
- Fuse 7.5a
- G13 (at left front corner of engine compartment)
- G3 (at right side of front deck crossmember)
- G6 (behind center of dash, near left center reinforcement)
- G7 (at top left side of dash)
- Hot at all times
- Hot in on
- Inlet side
- Interior lights system
- Joint connector 2
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Nca
- Off
- Outlet side
- Outside/inside air selection damper control motor (behind upper right end of dash)
- Pnk
- Resistor (behind right side of dash, on hvac unit)
Manual A/C Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Manual A/C Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (on engine compt relay box)
- (on left side of engine compt) engine compartment relay box
- A/c compressor
- A/c compressor clutch
- A/c compressor clutch relay
- A/c refrigerant temperature switch
- A34
- A35
- C117
- C119
- C121
- Condenser fan control relay (high) (on engine compt relay box)
- Condenser fan control relay (low)
- Condenser fan motor (mounted on rear of radiator)
- Dual pressure switch (on right side of engine compartment)
- Engine compartment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Engine control system
- Engine controls system
- Engine coolant temperature sensor (on rear of cylinder head)
- Fan control relay
- Fuse 10a
- Fuse 20a
- Fuse 30a
- Fuse 7.5a
- Fusible link 2 50a
- G13 (at left front corner of engine compartment)
- G13 (at left front corner of engine compt)
- Headlights, exterior lights & wiper/washer systems
- High pressure side on-off: 2940 kpa off-on: 2350 kpa
- Hot at all times
- Hot w/ taillight relay energized
- Joint connector 1 (behind center of dash)
- Joint connector 6 (behind lower center of dash)
- Low pressure side on-off: 196 kpa off-on: 221 kpa
- Mfi relay
- Nca
- Off
- Pnk
- Red
Manual A/C Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Manual A/C Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at left front corner of engine compartment)
- (behind center of dash, near left center reinforcement)
- (behind instrument cluster)
- A/c ecu (behind center of dash, below radio)
- A17
- A17-1
- A17-2
- Air thermo sensor (behind right center of of dash, on hvac unit)
- Blower motor (behind right end of dash)
- Blower relay
- Blower switch
- C210
- C211
- C214
- Condenser fan motor
- Defogger system
- Fan control module (on fan shroud, at left front of engine compartment)
- Fuse 30a
- Fuse 7.5a
- G13
- G3 (under right front kick panel)
- Heater control panel & illumination
- Hot at all times
- Hot in on
- Inlet side
- Interior lights system
- Joint connector 2
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Nca
- Off
- Outlet side
- Outside/inside air selection damper control motor (behind upper right end of dash)
- Radiator fan motor
- Resistor (behind right side of dash, on hvac unit)
Manual A/C Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Manual A/C Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at left front corner of engine compt)
- 2.0l a/t
- 2.0l m/t
- 2.4l
- 2.4l a/t
- 2.4l m/t
- A/c compressor assembly
- A/c compressor clutch
- A/c compressor clutch relay
- A/c refrigerant temperature switch (on-off: 150 degrees centigrade) (off-on: 120 degrees centigrade)
- C115
- C116
- C117
- C118
- C119
- C120
- C133
- C134
- C135
- C136
- C137
- C138
- C139
- C140
- Dual pressure switch (on right front of engine compt)
- Engine compartment relay box (on left side of engine compartment)
- Engine compartment relay box (on left side of engine compt)
- Engine controls system
- Engine coolant temperature sensor (on rear of cylinder head)
- Exterior lights system
- Fan control relay
- Fuse 10a
- Fuse 20a
- Fuse 7.5a
- Fusible link 2 50a
- G13
- High pressure side on-off: 3138 kpa off-on: 2550 kpa
- Hot at all times
- Hot w/ taillight relay energized
- Joint connector 1 (behind center of dash)
- Joint connector 6 (behind lower center of dash)
- Low pressure side on-off: 196 kpa off-on: 221 kpa
- Mfi relay
- Nca
- Off
- Pnk
- Powertrain control module (a/t) engine control module (m/t) (behind glove box)
- Red
ANTI-LOCK BRAKES
Anti-lock Brakes Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Anti-lock Brakes Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (under center console, left of parking brake lever assembly) (lateral) g-sensor
- Abs ecu (on right rear of engine compt)
- Abs ind
- Awd-ecu (behind lower right side of dash)
- C01
- C02
- C138
- C139
- C210
- C214
- Combination meter
- Data link connector (below left side of dash)
- Engine compartment relay box (on left side of engine compartment)
- Exterior lights system
- Fuse 10 15a
- Fuse 12 7.5a
- Fuse 2 7.5a
- Fuse 5 7.5a
- Fusible link 3 60a
- G-sensor (longitudinal) (under center console, left of parking brake lever assembly)
- G14 (under front of center console)
- G7 (at top left side of dash)
- Hot at all times
- Hot in on
- Hot in on or start
- Hydraulic unit
- Joint connector 2 (behind instrument cluster)
- Joint connector 4
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Left front abs sensor (on left front wheel hub assembly)
- Left rear abs sensor (on left rear hub assembly)
- Nca
- Parking brake switch (at base of parking brake lever)
- Pnk
- Red
- Right front abs sensor (on right front wheel hub assembly)
- Right rear abs sensor (on right rear hub assembly)
- Solenoid valve
- Steering angular velocity sensor (at top of steering column)
- Stoplight switch (above brake pedal, on bracket)
- Transmissions system
Anti-lock Brakes Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Anti-lock Brakes Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- Abs ecu (on right rear of engine compartment)
- Abs ind
- Abs solenoid valve
- Abs warning light relay (on junction block)
- C01
- C210
- C214
- Combination meter
- Cpu
- Data link connector (below left side of dash)
- Dedicated fuse 10 15a
- Engine compartment relay box (on left side of engine compartment)
- Exterior lights systems
- Fusible link 3 60a
- G14 (under front of center console)
- G3 (under right front kick panel)
- Hot at all times
- Hot in on
- Hot in on or start
- Hydraulic unit
- Joint connector 5 (behind instrument cluster)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Left front wheel speed sensor (on left front wheel hub assembly)
- Left rear wheel speed sensor (at left rear wheel)
- Multi- purpose fuse 12 7.5a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Red
- Right front wheel speed sensor (on right front wheel hub assembly)
- Right rear wheel speed sensor (at right rear wheel)
- Stoplight switch (above brake pedal, on bracket)
ANTI-THEFT
Immobilizer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Immobilizer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (at right side of front deck crossmember) g3
- (behind instrument cluster) joint connector 5
- All times
- C01
- C02
- C117
- C119
- C214
- Combination meter
- Engine compartment relay box (on left side of engine compartment)
- Engine control module (behind glove box)
- Engine controls system
- Fuse 20a
- Fuse 7.5a
- Hot at
- Hot in on or start
- Ignition key
- Ignition key ring antenna
- Immobilizer-ecu (behind left side of dash, near data link connectors)
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Key reminder switch (in steering column)
- Mfi relay (on engine compt relay box)
- Nca
- Red
- Security ind
BODY CONTROL MODULES
Body Control Modules Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Body Control Modules Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (at right side of front deck crossmember) g3
- (discharge headlight)
- (halogen headlight)
- 10a
- 20a
- A10x
- A11x
- All times
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Computer data lines system
- Dedicated fuse 13 10a
- Dedicated fuse 16 10a
- Dedicated fuse 17 10a
- Dedicated fuse 18
- Dedicated fuse 19
- Dedicated fuse 20 7.5a
- Dedicated fuse 21 7.5a
- Dedicated fuse 22 10a
- Dedicated fuse 23 10a
- Door locks system
- Engine compartment relay box (on left side of engine compartment)
- Engine compartment relay box (on left side of engine compartment)
- Etacs ecu
- Exterior lights system
- Front ecu
- G13 (at left front corner of engine compartment)
- G6 (behind center of dash, near left center reinforcement)
- Headlights system
- Headlights, wiper/washer, exterior lights systems
- Horns system
- Hot at
- Hot in
- Hot in on
- Interior lights & power windows systems
- Interior lights system
- Interior lights, door locks systems
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Multi- purpose fuse 14 15a
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- On or acc
- Or start
- Pnk
- Power window relay
- Red
- Warning system
- Wiper/ washer system
- Wiper/washer system
Body Control Modules Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Body Control Modules Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- A10x
- A11x
- All times
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Computer data lines system
- Dedicated fuse 13 10a
- Dedicated fuse 16 10a
- Dedicated fuse 17 10a
- Dedicated fuse 18 10a
- Dedicated fuse 19 10a
- Dedicated fuse 20 7.5a
- Dedicated fuse 21 7.5a
- Dedicated fuse 22 10a
- Dedicated fuse 23 10a
- Door locks system
- Engine compartment relay box (left side of engine compartment)
- Engine compartment relay box (left side of engine compartment)
- Etacs ecu
- Exterior lights system
- Front ecu
- G13 (at left front corner of engine compartment)
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- Headlights system
- Headlights, wiper/washer & exterior lights systems
- Horns system
- Hot at
- Hot in
- Hot in on
- Interior lights & door locks systems
- Interior lights & door locks systems
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Multi- purpose fuse 14 15a
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- On or acc
- Or start
- Pnk
- Power tops system
- Power window relay
- Red
- Warning system
- Wiper/washer system
COMPUTER DATA LINES
Computer Data Lines Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Computer Data Lines Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (behind instrument cluster)
- Abs ecu (on right rear of engine compt)
- Awd ecu (behind lower right side of dash)
- C01
- C12
- C138
- C14
- C15
- C214
- C228
- Combination meter
- Data link connector (below left side of dash)
- Engine control module (behind glove box)
- Etacs ecu
- Fuse 15a
- G7 (at top left side of dash)
- Hot at all times
- Joint connector 2
- Joint connector 4
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Srs ecu (behind lower center of dash)
- Vehicle speed sensor (at left side of engine compt)
Computer Data Lines Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Computer Data Lines Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (2.0l)
- (at left side of engine compt)
- (behind instrument cluster)
- (behind lower center of dash) srs ecu
- (behind right end of dash) (2.0l) auto cruise control ecu
- A/t
- Abs ecu (on right rear of engine compt)
- C01
- C114
- C115
- C116
- C137
- C137 (2.4l)
- C138
- C138 (2.4l)
- C14
- C15
- C214
- C228
- Combination meter
- Data link connector (below left side of dash)
- Engine control module (m/t) powertrain control module (a/t) (behind glove box)
- Etacs ecu
- G7 (at top left side of dash)
- Hot at all times
- Joint connector 2
- Joint connector 5 (behind instru- ment cluster)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- M/t
- Multi- purpose fuse 15 15a
- Red
- Vehicle speed sensor
COOLING FAN
Cooling Fan Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Cooling Fan Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (low)
- (mounted on rear of radiator)
- A17
- A17-1
- A34
- A35
- C119
- C121
- C210
- Condenser fan control relay (high) (on engine compt relay box)
- Condenser fan control relay (on engine compt relay box)
- Condenser fan motor
- Cooling fan motor
- Engine compartment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Engine controls system
- Engine coolant temperature sensor (on rear of cylinder head)
- Fan control module (on fan shroud, at left front of engine compt)
- Fan control relay (on engine compartment relay box)
- Fuse 11 30a
- Fuse 25 30a
- Fuse 5 7.5a
- Fuse 8 20a
- Fusible link 2 50a
- G13 (at left front corner of engine compt)
- Headlights, exterior lights & wiper/washer systems
- Hot at all times
- Hot in on
- Joint connector 2 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Mfi relay (on engine compartment relay box)
- Nca
- Red
Cooling Fan Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Cooling Fan Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- 2.0l
- 2.4l
- A/t
- A17
- A17-1
- A17-2
- C117
- C118
- C119
- C121
- C133
- C134
- C135
- C136
- C139
- C140
- Condenser fan motor
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- Engine coolant temperature sensor (on rear of cylinder head)
- Fan control module (on fan shroud, at left front of engine compt)
- Fan control relay (on engine compartment relay box)
- Fuse 8 20a
- Fusible link 2 50a
- G13 (at left front corner of engine compt)
- Hot at all times
- Joint connector 6 (behind lower center of dash)
- M/t
- Mfi relay (on engine compartment relay box)
- Nca
- Powertrain control module (a/t) engine control module (m/t) (behind glove box)
- Radiator fan motor
- Red
CRUISE CONTROL
2.0L
2.0L, Cruise Control Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Cruise Control Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash) joint connector 6
- Auto cruise control ecu (behind right end of dash)
- Auto cruise control switch
- Auto-cruise control vacuum pump (on right front of engine compartment)
- C01
- C02
- C114
- C116
- C118
- C120
- C204
- C214
- C229
- Cancel
- Clock spring
- Combination meter
- Computer data lines system
- Control valve
- Cruise ind
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- Exterior lights system
- Fuse 10 15a
- Fuse 2 7.5a
- Fuse 4 7.5a
- G14 (under front of center console)
- Hot at all times
- Hot in on or start
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Main
- Nca
- Off
- Output shaft speed sensor (on top right of transaxle)
- Powertrain control module (behind glove box)
- Red
- Release valve
- Resume
- Set
- Starting/ charging system
- Stoplight switch (above brake pedal, on bracket)
- Throttle position sensor (on throttle body)
2.0L, Cruise Control Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Cruise Control Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006:
- (above brake pedal, on bracket) stoplight switch
- (behind lower center of dash) joint connector 6
- Auto cruise control ecu (behind right end of dash)
- Auto cruise control switch
- Auto-cruise control vacuum pump (on right front of engine compartment)
- C-210
- C01
- C02
- C115
- C117
- C204
- C214
- C229
- Cancel
- Clock spring
- Clutch pedal position switch (above clutch pedal, on bracket)
- Combination meter
- Computer data lines system
- Control valve
- Cruise ind
- Engine compartment relay box (on left side of engine compartment)
- Engine control module (behind glove box)
- Engine controls system
- Exterior lights system
- Fuse 10 15a
- Fuse 2 7.5a
- Fuse 4 7.5a
- G14 (under front of center console)
- G15 (under left front kick panel)
- Hot at all times
- Hot in on or start
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Main
- Nca
- Off
- Red
- Release valve
- Resume
- Set
- Throttle position sensor (on throttle body)
- Vehicle speed sensor (on right side of transaxle)
2.4L
2.4L, Cruise Control Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Cruise Control Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006:
- (above brake pedal, on bracket)
- (under right front kick panel) g2
- Acc
- Accelerator pedal position sensor (right side of engine compartment)
- Auto-cruise control switch
- C-01
- C-02
- C-134
- C-136
- C-138
- C-140
- C-142
- C-204
- C-210
- C-214
- C-229
- Can
- Clock spring
- Combination meter
- Computer data lines system
- Cruise ind
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- Exterior lights system
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G14 (under front of center console)
- Hot at all times
- Hot in on or start
- Ignition switch
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Lock
- Main
- Mfi relay (on engine compartment relay box)
- Off
- Output shaft speed sensor (on top right of transaxle)
- Powertrain control module
- Red
- Res
- Set
- Start
- Starting/ charging system
- Stoplight switch
- Throttle actuator control motor
- Throttle actuator control motor relay (on engine compt relay box)
- Throttle position sensor (on throttle body)
- Transmission range switch
- Transmissions system
2.4L, Cruise Control Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Cruise Control Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006:
- (above clutch pedal, on) bracket) clutch pedal position switch
- Accelerator pedal position sensor (right side of engine compartment)
- Auto-cruise control switch
- C-01
- C-02
- C-133
- C-135
- C-137
- C-139
- C-141
- C-204
- C-210
- C-214
- C-229
- Can
- Clock spring
- Combination meter
- Computer data lines system
- Cruise ind
- Engine compartment relay box (left side of engine compartment)
- Engine control module (behind glove box)
- Engine controls system
- Exterior lights system
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G14 (under front of center console)
- G15 (under left front kick panel)
- G2 (under right front kick panel)
- Hot at all times
- Hot in on or start
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Main
- Mfi relay (on engine compartment relay box)
- Off
- Red
- Res
- Set
- Stoplight switch (above brake pedal, on bracket)
- Throttle actuator control motor
- Throttle actuator control motor relay (on engine compt relay box)
- Throttle position sensor (on throttle body)
- Vehicle speed sensor
DEFOGGERS
Defoggers Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for Defoggers Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- A/c ecu/ heater control unit (behind center of dash, below radio)
- C214
- C217
- Evolution
- F06
- F16
- G3 (under right front kick panel)
- Hot at all times
- Hot in on
- Interior lights system
- Junction block (behind left end of dash)
- Lancer
- Left remote controlled mirror
- Mirror heater
- Multi- purpose fuse 20 30a
- Multi- purpose fuse 5 7.5a
- Multi- purpose fuse 6 7.5a (lancer)
- Nca
- Rear window defogger
- Rear window defogger relay
- Right remote controlled mirror
ENGINE PERFORMANCE
2.0L
2.0L, Engine Performance Wiring Diagram, A/T (1 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Engine Performance Wiring Diagram, A/T (1 of 3) for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash) j/c 6
- (on engine compt relay box) mfi relay
- (on rear of cylinder head) camshaft position sensor
- (right side of engine)
- Air conditioning system
- C118
- C120
- Dedicated fuse 8 20a
- Egr solenoid valve
- Engine compartment relay box (left side of engine compt)
- Engine speed detection connector (in engine compt relay box)
- Evaporative emission purge solenoid valve
- G11 (left side of cylinder head, under throttle cable)
- G14 (under front of center console)
- G4 (at left rear of engine compt, on shock tower)
- Generator
- Hot at all times
- Ignition coil 1 (at top of valve cover)
- Ignition coil 2
- Instrument cluster system
- J/c 6 (behind lower center of dash)
- Nca
- Pnk
- Power steering oil pressure switch (right front of engine compt)
- Powertrain control module (behind glove box)
- Red
- Spark plugs
- Starting/ charging system
2.0L, Engine Performance Wiring Diagram, A/T (2 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Engine Performance Wiring Diagram, A/T (2 of 3) for Mitsubishi Lancer Ralliart 2006:
- (in exhaust manifold) heated oxygen sensor (front)
- (in exhaust, after catalytic converter) heated oxygen sensor (rear)
- Air conditioning
- Auto cruise control ecu (behind right end of dash)
- C01
- C210
- C214
- C217
- C228
- Combination meter
- Control circuit
- Crankshaft position sensor (on lower front of engine)
- Dedicated fuse 15 15a
- Engine compartment relay box (left side of engine compt)
- Engine coolant temperature sensor (on rear of cylinder head)
- Etacs ecu
- Evaporative emission ventilation solenoid valve (below left rear of vehicle)
- Fuel pump module
- Fuel pump relay
- Fuel tank differential pressure sensor (on top right side of fuel tank)
- G6 (behind center of dash, near left center reinforcement)
- G9 (at rear shelf panel)
- Hot at all times
- Hot in on or start
- Idle air control motor (below throttle body)
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Malfunction indicator lamp (mil)
- Manifold absolute pressure sensor (on top of intake manifold)
- Multi- purpose fuse 1 10a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 8 7.5a
- Nca
- Pnk
- Red
- System red
- Throttle position sensor (on throttle body)
- Volume airflow sensor (left rear corner of engine compt)
2.0L, Engine Performance Wiring Diagram, A/T (3 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Engine Performance Wiring Diagram, A/T (3 of 3) for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash) j/c 6
- (below left side of dash) data link connector (dlc)
- A/t control relay (on engine compt relay box)
- A/t control solenoid valve assembly (on rear of transaxle)
- A/t fluid temp
- Air conditioning system
- C114
- C116
- C14
- C15
- C210
- Dedicated fuse 10 15a
- Dedicated fuse 14 20a
- Engine compartment relay box (left side of engine compt)
- Engine compartment relay box (left side of engine compt) red
- Exterior lights system
- G14 (under front of center console)
- G4 (at left rear of eng compt, on shock tower)
- Hot at all times
- Hot in run or start
- Input shaft speed sensor (on top center of transaxle)
- J/c 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Knock sensor (on right side of engine block)
- Low/ reverse
- Multi- purpose fuse 3 7.5a
- Output shaft speed sensor (on top right of transaxle)
- Over drive
- Pnk
- Powertrain control module (behind glove box)
- Red
- Second
- Starting/ charging system
- Stoplight switch (above brake pedal, on bracket)
- Torque converter control
- Transmission range switch (left front of engine compt)
- Under drive
2.0L, Engine Performance Wiring Diagram, M/T (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Engine Performance Wiring Diagram, M/T (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (on engine compt relay box) mfi relay
- (on rear of cylinder head) camshaft position sensor
- (on right side of engine)
- Air conditioning system
- Air conditioning system
- C117
- C119
- D10
- D12
- Dedicated fuse 8 20a
- Egr solenoid valve
- Engine compartment relay box (left side of engine compt)
- Engine control module (behind glove box)
- Engine speed detection connector (in engine compt relay box)
- Evaporative emission purge solenoid valve
- Fuel pump module (at fuel tank)
- G14 (under front of center console)
- G4 (at left rear of eng compt, on shock tower)
- G9 (at rear shelf panel)
- Hot at all times
- Idle air control motor (below throttle body)
- Ignition coil 1 (at top of valve cover)
- Ignition coil 2
- Instrument cluster system
- J/c 6 (behind lower center of dash)
- Nca
- Pnk
- Power steering pressure switch (right front of engine compt)
- Red
- Spark plugs
- Starting/ charging system
2.0L, Engine Performance Wiring Diagram, M/T (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, Engine Performance Wiring Diagram, M/T (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (in exhaust manifold) heated oxygen sensor (front)
- (in exhaust, after catalytic converter) heated oxygen sensor (rear)
- (on lower front of engine) crankshaft position sensor
- Air conditioning system
- Auto cruise control ecu (behind right end of dash)
- C115
- C210
- C214
- C217
- Combination meter
- Computer data lines system
- Cruise control system
- Dedicated fuse 15 15a
- Engine compartment relay box (left side of engine compt)
- Engine control module (behind glove box)
- Engine coolant temperature sensor (on rear of cylinder head)
- Evaporative emission ventilation solenoid valve (below left rear of vehicle)
- Fuel pump relay
- Fuel tank differential pressure sensor (on top right side of fuel tank)
- G14 (under front of center console)
- G4 (at left rear of eng compt, on shock tower)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in on or start
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Knock sensor (on right side of engine block)
- Malfunction indicator lamp (mil)
- Manifold absolute pressure sensor (on top of intake manifold)
- Multi- purpose fuse 1 10a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 8 7.5a
- Nca
- Pnk
- Red
- Throttle position sensor (on throttle body)
- Vehicle speed sensor (at left side of engine compartment)
- Volume airflow sensor (on left rear corner of engine compt)
2.0L TURBO
2.0L Turbo, Engine Performance Wiring Diagram (1 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L Turbo, Engine Performance Wiring Diagram (1 of 3) for Mitsubishi Lancer Ralliart 2006:
- (at rear of engine) injector
- (at right rear of engine compartment) injector resistor
- (at top center of valve cover) injector
- (at top front of valve cover) injector
- (on engine compt relay box) mfi relay
- (on rear of cylinder head) exhaust camshaft position sensor
- (on right side of engine)
- 47
- Air conditioning system
- B25
- C119
- C121
- Clutch pedal position switch (above nca
- Clutch pedal, on bracket)
- Control valve (front of engine)
- Cooling fans system
- Dedicated fuse 8 20a
- Egr vacuum regulator solenoid valve
- Engine compartment relay box (left side of engine compt)
- Engine control module (behind glove box)
- Evaporative emission purge solenoid valve
- Fuel pressure solenoid (on right side of engine)
- G15 (under left front kick panel)
- G4 (left side of engine compartment)
- Generator (front of engine)
- Hot at all times
- Idle air control motor (below throttle body)
- Intake camshaft position sensor (on rear of cylinder head)
- J/c 6 (behind lower center of dash)
- Nca
- Oil feeder
- Pnk
- Power steering pressure switch (right front of engine compt)
- Red
- Turbocharger wastegate solenoid (left front of engine compt)
2.0L Turbo, Engine Performance Wiring Diagram (2 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L Turbo, Engine Performance Wiring Diagram (2 of 3) for Mitsubishi Lancer Ralliart 2006:
- C210
- C214
- Dedicated fuse 15 20a
- Engine compartment relay box (left side of engine compt)
- Fuel level sensor (sub) (on top right side of fuel tank)
- Fuel pump & level sensor (main) (in fuel tank)
- Fuel pump relay
- Fuel pump relay 3 (at right side of firewall)
- Fuel pump resistor (right rear of engine compt)
- Fuel tank temperature sensor (on top of fuel tank)
- G11 (at rear of engine, below cylinder head)
- G2 (at right "a" pillar)
- G4 (left side of engine compt)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in on or start
- Ignition coil 1 (at rear of engine)
- Ignition coil 2 (top front of engine)
- Instrument cluster system
- Junction block (behind left end of dash)
- Knock sensor (on right side of engine block)
- Multi- purpose fuse 8 7.5a
- Nca
- Red
- Spark plugs
2.0L Turbo, Engine Performance Wiring Diagram (3 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L Turbo, Engine Performance Wiring Diagram (3 of 3) for Mitsubishi Lancer Ralliart 2006:
- c117
- (behind glove box) engine control module
- (behind instrument cluster) j/c 5
- (below left rear of vehicle) evaporative emission ventilation solenoid valve
- (below left side of dash) data link connector (dlc)
- (left side of of engine compt) g4
- (on exhaust manifold) heated oxygen sensor (front)
- (on exhaust pipe, downstream of catalytic converter) heated oxygen sensor (rear)
- (on lower front of engine) crankshaft position sensor
- Air condi- tioning system
- Air conditioning system
- Anti-theft system
- C01
- C119
- C14
- C15
- C210
- C214
- Combination meter
- Engine coolant temperature sensor (on rear of cylinder head)
- Engine speed detection connector (in engine compt relay box)
- Fuel tank differential pressure sensor (on top right side of fuel tank)
- G14 (under front of center console)
- Hot in on or start
- J/c 2 (behind instrument cluster)
- J/c 4
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Malfunction indicator lamp (mil)
- Manifold absolute pressure sensor (at left rear of engine compartment)
- Multi- purpose fuse 1 10a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Red
- Starting/ charging system
- Throttle position sensor (on throttle body)
- Transmissions system
- Vehicle speed sensor (on right side of transaxle)
- Volume airflow sensor (on left front corner of engine compt)
2.4L
2.4L, Engine Performance Wiring Diagram, A/T (1 of 5) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, A/T (1 of 5) for Mitsubishi Lancer Ralliart 2006:
- (on engine compt relay box) mfi relay
- (on rear of cylinder head) camshaft position sensor
- (rear of cylinder head) engine oil control valve
- (right side of engine)
- (under front of center console) g14
- Air conditioning system
- C-134
- C-136
- Cooling fans system
- Cruise control system
- Dedicated fuse 8 20a
- Engine compartment relay box (left side of engine compt)
- Engine oil pressure switch (at rear of engine)
- Evaporative emission purge solenoid valve
- Exhaust gas recirculation valve (on right side of engine)
- Fuel injectors
- G4 (at left rear of eng compt, on shock tower)
- Hot at all times
- Ignition coil 1 (on top of engine)
- Ignition coil 2 (top front of engine)
- Ignition coil 3 (on top of engine)
- Ignition coil 4 (top of engine)
- J/c 6 (behind lower center of dash)
- Nca
- Pnk
- Power steering oil pressure switch (on power steering pump)
- Powertrain control module
- Red
- Spark plug
- Starting/charging system
2.4L, Engine Performance Wiring Diagram, A/T (2 of 5) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, A/T (2 of 5) for Mitsubishi Lancer Ralliart 2006:
- (in exhaust, after catalytic converter) heated oxygen sensor (rear)
- (in exhaust, at catalytic converter) heated oxygen sensor (front)
- C01
- C210
- C214
- C217
- Combination meter
- Control circuit
- Crankshaft position sensor (behind timing belt cover, above crankshaft)
- Dedicated fuse 15 15a
- Engine compartment relay box (left side of engine compt)
- Engine coolant temperature sensor (on rear of cylinder head)
- Evaporative emission ventilation solenoid valve (below left rear of vehicle)
- Fuel pump relay
- Fuel tank differential pressure sensor (on top right side of fuel tank)
- Hot at all times
- Hot in on or start
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Malfunction indicator lamp (mil)
- Manifold absolute pressure sensor (on intake manifold)
- Mass airflow sensor (on air intake tube)
- Multi- purpose fuse 1 10a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 8 7.5a
- Pnk
- Red
2.4L, Engine Performance Wiring Diagram, A/T (3 of 5) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, A/T (3 of 5) for Mitsubishi Lancer Ralliart 2006:
- (below left side of dash) data link connector (dlc)
- (on engine compartment relay box)
- C14
- C228
- Etacs ecu
- Fuel pump module (at fuel tank)
- G9 (at rear shelf panel)
- Instrument cluster system
- J/c 2 (behind instrument cluster)
- J/c 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Pnk
- Red
- Throttle actuator control motor relay
2.4L, Engine Performance Wiring Diagram, A/T (4 of 5) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, A/T (4 of 5) for Mitsubishi Lancer Ralliart 2006:
- A/t control relay (on engine compt relay box)
- A/t control solenoid valve assembly (on rear of transaxle)
- A/t fluid temp
- C210
- Dedicated fuse 10 15a
- Dedicated fuse 14 20a
- Engine compartment relay box (left side of engine compt)
- Engine compartment relay box (left side of engine compt) red
- Exterior lights system
- Hot at all times
- Hot in run or start
- Input shaft speed sensor (on top center transaxle)
- Interior lights system
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Low/ reverse
- Multi- purpose fuse 3 7.5a
- Output shaft speed sensor (on top right of transaxle)
- Over drive
- Red
- Second
- Starting/ charging system
- Stoplight switch (above brake pedal, on bracket)
- Torque converter control
- Transmission range switch
- Under drive
2.4L, Engine Performance Wiring Diagram, A/T (5 of 5) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, A/T (5 of 5) for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash)
- (on throttle body) throttle position sensor
- (pins 109-112 not used)
- (right side of engine compt) accelerator pedal position sensor
- Air conditioning system
- C-138
- C-140
- C-142
- Cruise control system
- Engine speed detection connector (in engine compt relay box)
- G14 (under front of center console)
- G4 (at left rear of eng compt, on shock tower)
- J/c 6
- J/c 6 (behind lower center of dash)
- Knock sensor (in engine block, above oil pan)
- Powertrain control module
- Red
- Starting/charging system
- Tac motor
2.4L, Engine Performance Wiring Diagram, M/T (1 of 4) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, M/T (1 of 4) for Mitsubishi Lancer Ralliart 2006:
- (on engine compt relay box) mfi relay
- (on rear of cylinder head) camshaft position sensor
- (on rear of cylinder head) engine oil control valve
- (on right side of engine)
- Air conditioning system
- C-133
- C-135
- Cooling fans system
- Cruise control system
- Dedicated fuse 8 20a
- Engine compartment relay box (left side of engine compt)
- Engine control module (behind glove box)
- Engine oil pressure switch (at rear of engine)
- Evaporative emission purge solenoid valve
- Exhaust gas recirculation valve (on right side of engine)
- Fuel injectors (at intake manifold)
- G14 (under front of center console)
- G4 (at left rear of engine compt, on shock tower)
- Hot at all times
- Ignition coil 1 (at top of engine)
- Ignition coil 2 (top front of engine)
- Ignition coil 3 (on top of engine)
- Ignition coil 4 (top of engine)
- J/c 6 (behind lower center of dash)
- Nca
- Pnk
- Power steering oil pressure switch (on power steering pump)
- Red
- Spark plug
- Starting/charging system
2.4L, Engine Performance Wiring Diagram, M/T (2 of 4) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, M/T (2 of 4) for Mitsubishi Lancer Ralliart 2006:
- (in exhaust, after catalytic converter) heated oxygen sensor (rear)
- (in exhaust, at catalytic converter) heated oxygen sensor (front)
- C01
- C210
- C214
- C217
- Combination meter
- Crankshaft position sensor (behind timing belt cover, above crankshaft)
- Dedicated fuse 15 15a
- Engine compartment relay box (left side of engine compt)
- Engine coolant temperature sensor (on rear of cylinder head)
- Fuel pump relay
- Fuel tank differential pressure sensor (on top right side of fuel tank)
- Hot at all times
- Hot in on or start
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Malfunction indicator lamp (mil)
- Manifold absolute pressure sensor (on intake manifold)
- Mass airflow sensor
- Multi- purpose fuse 1 10a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 8 7.5a
- Nca
- Pnk
- Red
2.4L, Engine Performance Wiring Diagram, M/T (3 of 4) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, M/T (3 of 4) for Mitsubishi Lancer Ralliart 2006:
- (below left side of dash) data link connector (dlc)
- (on engine compartment relay box)
- C14
- C15
- D10
- D12
- Fuel pump module & fuel level sensor (at fuel tank)
- G14 (under front of center console)
- G9 (at rear shelf panel)
- Instrument cluster system
- J/c 2 (behind instrument cluster)
- J/c 5 (behind instrument cluster)
- Pnk
- Red
- Throttle actuator control motor relay
- Vehicle speed sensor (at left side of engine compt)
2.4L, Engine Performance Wiring Diagram, M/T (4 of 4) for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, Engine Performance Wiring Diagram, M/T (4 of 4) for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash)
- (on throttle body) throttle position sensor
- (pins 109-112 not used)
- (right side of engine compartment) accelerator pedal position sensor
- Air conditioning system
- C-137
- C-139
- C-141
- Cruise control system
- Engine control module (behind glove box)
- Engine speed detection connector (in engine compt relay box)
- G14 (under front
- G14 (under front of center console)
- G4 (at left rear of engine compt, on shock tower)
- J/c 6
- J/c 6 (behind lower center of dash)
- Knock sensor (in engine block, above oil pan)
- Of center console)
- Red
- Starting/charging system
- Tac motor
EXTERIOR LIGHTS
Back-up Lamps Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Back-up Lamps Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- Back-up light switch (on transaxle)
- C210
- G8 (under rear seat back, at right upper corner of rear shelf panel)
- G9 (under rear seat back, at left upper corner of rear shelf panel)
- Hot in run or start
- Joint connector 4
- Junction block (behind left end of dash)
- Left back-up light
- Left rear combination light assembly
- Multi- purpose fuse 3 7.5a
- Nca
- Red
- Right back-up light
- Right rear combination light assembly
Back-up Lamps Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Back-up Lamps Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (behind instrument cluster) joint connector 2
- A/t
- Back-up light switch (on top of transaxle)
- C210
- G8 (at rear shelf panel)
- G9 (at rear shelf panel)
- Hot in on or start
- Junction block (behind left end of dash)
- Left back-up light
- Left rear combination light assembly
- M/t
- Multi- purpose fuse 3 7.5a
- Nca
- Red
- Right back-up light
- Right rear combination light assembly
- Transmission range switch (left front of engine compt)
Exterior Lamps Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Exterior Lamps Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (not used)
- A10x
- A11x
- Air conditioning system
- Anti-lock brakes system
- Back-up lamps circuit
- C210
- C217
- Dedicated fuse 10 15a
- Dedicated fuse 13 10a
- Dedicated fuse 20 7.5a
- Dedicated fuse 21 7.5a
- Dedicated fuse 22 10a
- Engine compartment relay box (on left side of engine compartment)
- Front ecu
- G1 (at right front corner of engine compartment)
- G13 (at left front corner of engine compartment)
- G8 (under rear seat back, at right upper corner of rear shelf panel)
- G9 (under rear seat back, at left upper corner of rear shelf panel)
- Gnd
- Headlights system
- High mounted stop light
- Hot at all times
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left front combi- nation assembly
- Left license plate light
- Left rear combination light assembly turn
- Left rear side marker light
- Left side turn signal light
- Nca
- Off
- Position
- Power source
- Red
- Right license plate light
- Right rear combination light assembly turn
- Right rear side marker light
- Stop
- Stoplight switch (above brake pedal, on bracket)
- Tail
- Taillight relay
- Turn
- Vehicles w/ halogen headlights
- Vehicles w/ hid headlights
Exterior Lamps Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Exterior Lamps Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Column switch (on top of steering column)
- Column-ecu
- Combination meter
- Data link connector (below left side of dash)
- Etacs ecu
- G1 (at right front corner of engine compt)
- G13 (at left front corner of engine compt)
- G3 (at right side of front deck crossmember)
- G6 (behind center of dash, near left center reinforcement)
- G7 (at top left side of dash)
- Gnd
- Hazard warning light switch
- Head
- Hot in on
- Hot in on or start
- Illum
- Interior lights system
- Joint connector
- Joint connector (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Junction block (behind left end of dash)
- Left turn ind
- Left turn signal light relay
- Lighting switch
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Off
- Pnk
- Position
- Power source
- Right front combination light assembly
- Right side turn signal light
- Right turn ind
- Right turn signal light relay
- Tail
- Turn
- Vehicles w/ halogen headlights
- Vehicles w/ hid headlights
Exterior Lamps Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Exterior Lamps Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- A10x
- A11x
- Anti-lock brakes system
- Back-up lamps circuit
- C210
- C217
- Cruise control system
- Dedicated fuse 10 15a
- Dedicated fuse 13 10a
- Dedicated fuse 20 7.5a
- Dedicated fuse 21 7.5a
- Dedicated fuse 22 10a
- Engine compartment relay box (on left side of engine compartment)
- Front ecu
- G1 (at right front corner of engine compartment)
- G13 (at left front corner of engine compartment)
- G13 (at left front corner of engine compt)
- G7 (at top left side of dash)
- G8 (at rear shelf panel)
- G9 (at rear shelf panel)
- Gnd
- High mounted stop light (rear shelf)
- High mounted stop light (rear spoiler)
- Hot at all times
- Joint connector (behind center of dash)
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left front turn signal light
- Left license plate light
- Left position light
- Left rear combination light assembly
- Left side turn signal light
- Nca
- Off
- Power source
- Red
- Right license plate light
- Right position light
- Right rear combination light assembly
- Stop
- Stoplight switch (above brake pedal, on bracket)
- Tail
- Taillight relay
- Turn
Exterior Lamps Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Exterior Lamps Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Column ecu
- Column switch
- Combination meter
- Data link connector (below left side of dash)
- Etacs ecu
- G1 (at right front corner of engine compt)
- G13 (at left front corner of engine compt)
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- G7 (at top left side of dash)
- Gnd
- Hazard warning light switch
- Head
- Hot in on
- Hot in start or on
- Interior lights system
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left turn ind
- Left turn signal light relay
- Lighting switch
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Off
- Pnk
- Power source
- Power tops system
- Right front turn signal light
- Right side turn signal light
- Right turn ind
- Right turn signal light relay
- Tail
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Ground Distribution Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- Battery
- Clutch interlock switch & clutch pedal position switch
- Combination meter, audio amplifier & connector lock switch
- Electric pump relay, windshield wiper motor, abs ecu, engine control module, awd-ecu, vehicle speed sensor & brake fluid level indicator switch
- Fuel pump relay 1, etacs ecu, combination meter & blower motor
- G1 (at right front corner of engine compartment)
- G10 (at lower left rear of engine)
- G11 (at rear of engine, below cylinder head)
- G13 (at left front corner of engine compartment)
- G14 (under front of center console)
- G15 (under left front kick panel)
- G16 (behind center of dash, on right dash support)
- G17 (at sunroof motor assembly)
- G2 (at right "a" pillar)
- G3 (at right side of front deck crossmember)
- G4 (left side of engine compartment)
- G5 (on center tunnel, right of accelerator pedal)
- G6 (behind center of dash, near left center reinforcement)
- G7 (at top left side of dash)
- G8 (under rear seat back, at right upper corner of rear shelf panel)
- G9 (under rear seat back, at left upper corner of rear shelf panel)
- Headlight leveling switch, hazard warning light switch, rheostat, immobilizer ecu, steering angular velocity sensor, cigarette lighter, heater control (a/c ecu), blower relay, seat belt switch, etacs ecu, data link connector, combination meter, fog light switch, clock, column switch, key reminder switch & ashtray illumination light
- Headlight leveling switch, heater control (a/c ecu), seat belt switch, blower relay, cigarette lighter, clock, column switch, etacs ecu, fog light switch, key reminder switch, left door lock key cylinder switch, left front door lock actuator, power window main switch, power window sub switch, remote controlled mirror switch, steering angular velocity sensor, immobilizer-ecu, hazard warning light switch & ashtray illumination light
- Ignition coils
- Left front combination light assembly, right front combination light assembly, left headlight (high), right side turn signal light & right fog light
- Left front combination light assembly, right headlight, left fog light, condenser fan motor, fan control module, fan control relay, front ecu, left side turn signal light & right front combination light assembly
- License plate lights, left rear combination light assembly,
- Main fuel pump & level sensor, fuel temperature sensor & right side turn signal light
- Pressure unit assembly, awd-ecu, proportioning valve, knock sensor shield, vehicle speed sensor, ignition coils, electric pump relay, engine control module
- Rear washer motor, right rear combination light assembly & windshield washer motor
- Rear window defogger
- Rear wiper motor, rear side marker lights & high mounted stoplight
- Sunroof motor assembly & sunroof switch
Ground Distribution Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Ground Distribution Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- 2.4l
- Abs ecu, auto-cruise control ecu (2.0l), throttle position sensor shield (2.4l), engine control module, brake fluid level indicator switch, powertrain control module, vehicle speed sensor (m/t) & windshield wiper motor
- Battery
- Brake fluid level indicator switch, clutch pedal position switch (m/t), & starter relay interlock switch
- Data link connector, combination meter, rheostat, rear shelf high mounted stoplight, rear spoiler high mounted stoplight & etacs ecu
- Etacs ecu
- Fuel level sensor, fuel pump module, license plate lights & left rear combination light assembly
- Fuel pump relay 1, etacs ecu, audio amplifier & blower motor
- G1 (at right front corner of engine compartment)
- G10 (at rear of cylinder head)
- G11 (on left side of cylinder head, under throttle cable)
- G12 (at left front of engine compartment, left of battery)
- G13 (at left front corner of engine compartment)
- G14 (under front of center console)
- G15 (under left front kick panel)
- G16 (behind center of dash, on right dash support)
- G2 (under right front kick panel)
- G3 (under right front kick panel)
- G4 (at left rear of engine compartment, on shock tower)
- G5 (on center tunnel, right of accelerator pedal)
- G6 (behind center of dash, near left center reinforcement)
- G7 (at top left side of dash)
- G8 (at rear shelf panel)
- G9 (at rear shelf panel)
- Ignition coils
- Ignition coils, powertrain control module, knock sensor shield & engine control module
- Left headlight, left position light, right side turn signal light & windshield washer motor
- Occupant classification-ecu & srs-ecu
- Rear window defogger
- Right front turn signal light, right headlight, fog lights, fan control module, fan control relay, front ecu, left side turn signal light, left front turn signal light & right position light
- Right rear combination light assembly, sunroof motor assembly & sunroof switch
- Seat belt switch, heater control unit (a/c ecu), abs warning light relay, blower relay, cigarette lighter, clock, column switch, etacs ecu, fog light switch, key reminder switch, left door lock key cylinder switch, ashtray illumination light, left front door lock actuator, power window main switch, right front power window sub switch, remote controlled mirror switch, left remote controlled mirror, right remote controlled mirror & hazard warning light switch
- Stoplight switch
HEADLIGHTS
Headlights Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Headlights Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (at left front corner of engine compartment)
- (at right front corner of engine compartment)
- (at right side of front deck crossmember)
- (at right side of front deck crossmember) g3
- (at top left side of dash)
- (behind center of dash, near left center reinforcement) g6
- (on left side of engine compt) engine compartment relay box
- A10x
- A11x
- Air conditioning system
- Beam ind
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Column switch (on top of steering column)
- Column-ecu
- Combination meter
- Computer data lines system
- Controller discharge
- Dedicated fuse 16 10a
- Dedicated fuse 17 10a
- Dedicated fuse 18 20a 10a
- Dedicated fuse 19 20a 10a
- Dedicated fuse 20 7.5a
- Dimmer/ passing switch
- Discharge controller
- Etacs ecu
- Fog ind
- Fog light relay (on engine compt relay box)
- Fog light switch
- Front ecu
- Front ecu (in engine compt relay box)
- Fuse 10a
- Fuse 15a
- G1 (at right front corner of engine compt)
- G13
- G13 (at left front corner of engine compartment)
- G13 (at left front corner of engine compt)
- Halogen headlight
- Head
- Headlight
- Headlight relay high
- Headlight relay low
- Hid
- Hid bulb
- Hid headlights
- Hot at all times
- Hot in on
- Hot in on or start
- Ill
- Interior lights system
- Joint conn- ector 2 (behind instru- ment cluster)
- Joint conne- ctor 1 (behind center of dash)
- Joint conne- ctor 2 (behind instru- ment cluster)
- Joint connector (behind right side of dash)
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Junction block (behind left end of dash)
- Left fog light
- Left front combi- nation light assembly
- Left front combination light assembly
- Left front door switch
- Left headlight
- Lighting switch
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Nca
- Off
- Pass
- Pnk
- Red
- Right fog light
- Right front combi- nation light asse- mbly
- Right front combination light assembly
- Right headlight
- Tail
- Taillight relay
Headlights Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Headlights Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (at left front corner of engine compartment)
- (at top left side of dash) g7
- (behind instrument cluster)
- A10x
- A11x
- Beam ind
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Column switch (on top of steering column)
- Column-ecu
- Combination meter
- Computer data lines system
- Dedicated fuse 16 10a
- Dedicated fuse 17 10a
- Dedicated fuse 18 10a
- Dedicated fuse 19 10a
- Dedicated fuse 22 10a
- Dedicated fuse 6 15a
- Dimmer/ passing switch
- Engine compartment relay box (left side of engine compt)
- Etacs ecu
- Fog ind
- Fog light relay (on engine compartment relay box)
- Fog- light switch
- Front ecu
- Front-ecu (in engine compt relay box)
- G1 (at right front corner of engine compartment)
- G13
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- Head
- Headlight relay high
- Headlight relay low
- Hot at all times
- Hot in on
- Hot in on or start
- Illum
- Interior lights system
- J/c 3 (behind right side of dash)
- Joint conn- ector 2 (behind instru- ment cluster)
- Joint connector (behind center of dash)
- Joint connector (behind right side of dash)
- Joint connector 5
- Junction block (behind left end of dash)
- Left fog- light
- Left front door switch (at left front door)
- Left headlight
- Lighting switch
- Low field effect transistor for headlight
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Nca
- Off
- Pass
- Pnk
- Pulse width modulation
- Red
- Right fog- light
- Right headlight
- Tail
HORN
Horn Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Horn Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (behind left center of front bumper fascia)
- (behind left end of front bumper fascia)
- Clock spring
- Dedicated fuse 7 10a
- Engine compartment relay box (on left side of engine compt)
- Horn (hi)
- Horn (lo)
- Horn relay (on engine compt relay box)
- Horn switch
- Hot at all times
- Joint connector 5 (behind instrument cluster)
- Nca
- Red
Horn Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Horn Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- Clock spring
- Dedicated fuse 7 10a
- Engine compartment relay box (on left side of engine compartment)
- Horn (hi) (behind left center of front bumper fascia)
- Horn (low) (behind left center of front bumper fascia)
- Horn relay (on engine compt relay box)
- Horn switch
- Hot at all times
- Joint connector 2 (behind instrument cluster)
- Nca
- Red
INSTRUMENT CLUSTER
Instrument Cluster Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Cluster Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at top left side of dash) g7
- Abs ind
- Anti-lock brakes system
- Anti-theft system
- Brake fluid level indicator switch (on brake master cylinder reservoir)
- Brake ind
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Charge ind
- Combination meter
- Control circuit
- Door ind
- Engine coolant temperature gauge unit (left rear of engine)
- Engine oil pressure switch (at rear of engine)
- Etacs ecu
- Exterior lights system
- Fog ind
- Fuel gauge
- Fuel ind
- Fuse 2 7.5a
- G14 (under front of center console)
- Headlights system
- High beam ind
- Hot in on or start
- Illumination
- Interior lights system
- Joint connector 4
- Junction block (behind left end of dash)
- Left turn ind
- Malfunction ind light
- Nca
- Odometer/trip
- Oil ind
- Parking brake switch (at base of parking brake lever)
- Pnk
- Red
- Right turn ind
- Seat belt ind
- Security ind
- Speedometer
- Srs ind
- Starting/charging system
- Tachometer
- Temperature gauge
- Warning system
Instrument Cluster Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Cluster Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at left rear door) left rear door switch
- (at right rear door) right rear door switch
- (at right side of front deck cross member) g3
- (on top right side of fuel tank) fuel level sensor (sub)
- C117
- C119
- C121
- Clock
- Detection connector (in engine compt relay box)
- Engine compartment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Engine controls system
- Engine speed
- Fuel pump & level sensor (main) (in fuel tank)
- Fuse 20 7.5a
- Fuse 22 10a
- Fuse 23 10a
- G14 (under front of center console)
- G2 (at right "a" pillar)
- Hot at all times
- Hot in on or acc
- Hot with tail- light relay energized
- Joint connector (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- Left front door switch
- Nca
- Red
- Right front door switch
- Vehicle speed sensor (on right side of transaxle)
Instrument Cluster Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Cluster Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at top left side of dash) g7
- A/t
- Abs ind
- Anti-lock brakes system
- Brake fluid level indicator switch (2.4l: on brake fluid master cylinder reservoir) (2.0l: on brake master cylinder reservoir)
- Brake ind
- C01
- C02
- C210
- C214
- C217
- C226
- C228
- Charge ind
- Combination meter
- Control circuit
- Cruise control system
- Cruise ind
- Door ind
- Engine coolant temperature gauge unit (left rear of engine)
- Engine oil pressure switch (2.0l: on right front of engine) (2.4l: at rear of engine)
- Etacs ecu
- Exterior lights system
- Exterior lights system
- Fog ind
- Fuel gauge
- Fuel ind
- Fuse 2 7.5a
- Fuse 3 7.5a
- G14 (under front of center console)
- Headlights system
- High beam ind
- Hot in on or start
- Illumination
- Interior lights system
- Joint connector 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left turn ind
- M/t
- Malfunction ind light
- Nca
- Odometer/trip
- Oil ind
- Parking brake switch (at base of parking brake lever)
- Pnk
- Red
- Right turn ind
- Seat belt ind
- Speedometer
- Srs ind
- Starting/charging system
- Tachometer
- Temperature gauge
- Warning system
Instrument Cluster Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Cluster Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at left front door) left front door switch
- (at left rear door) left rear door switch
- (at right front door) right front door switch
- (at right rear door) right rear door switch
- (under right front kick panel) g3
- 2.0l a/t
- 2.0l m/t
- 2.4l a/t
- 2.4l m/t
- C114
- C115
- C116
- C117
- C118
- C119
- C120
- C133
- C134
- C137
- C138
- Clock
- Detection connector (in engine compt relay box)
- Engine compartment relay box (left side of engine compt)
- Engine speed
- Fuel level sensor (in fuel tank)
- Fuse 20 7.5a
- Fuse 22 10a
- Fuse 23 10a
- G14 (under front of center console)
- G9 (at rear shelf panel)
- Hot at all times
- Hot in on or acc
- Hot w/ tail- light relay energized
- Joint connector (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 5 (behind instrument cluster)
- Joint connector 6 (behind lower center of dash)
- M/t
- Output shaft speed sensor (a/t) (on top right of transaxle)
- Pnk
- Powertrain control module (a/t) engine control module (m/t) (behind glove box)
- Red
- Transmissions & engine controls systems
- Transmissions system
- Vehicle speed sensor (m/t) (at left side of engine compt)
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Courtesy Lamps Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (at right side of front deck crossmember) g3
- (behind center of dash, near left center reinforcement)
- (behind instrument cluster)
- (in steering column) (closed when key is removed) key reminder switch
- 10a
- C01
- C02
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Combination meter
- Dedicated fuse 22
- Dedicated fuse 23
- Door
- Engine compartment relay box (on left side of engine compartment)
- Etacs ecu
- Front dome light
- G3 (at right side of front deck crossmember)
- Hot at all times
- Hot in acc or on
- Hot in start or on
- Illum
- Ind
- Joint connector 1 (behind center of dash)
- Joint connector 2
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Junction block (behind left end of dash)
- Left front door switch
- Left rear door switch (at left rear door)
- Luggage compartment light
- Luggage compartment light switch
- Map
- Multi- purpose fuse 14 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Off
- Rear dome light (w/o sunroof)
- Red
- Right front door switch
- Right rear door switch (at right rear door)
- Room
Courtesy Lamps Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Courtesy Lamps Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (behind center of dash, near left center reinforcement) g6
- (in steering column) (closed when key is removed) key reminder switch
- 10a
- C01
- C02
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Combination meter
- Dedicated fuse 22
- Dedicated fuse 23
- Door
- Door ind
- Engine compartment relay box (on left side of engine compartment)
- Etacs ecu
- Front dome light
- G3 (under right front kick panel)
- Hot at all times
- Hot in acc or on
- Hot in start or on
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Left front door switch (at left front door)
- Left rear door switch (at left rear door)
- Luggage compartment light
- Luggage compartment light switch
- Map
- Multi- purpose fuse 14 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Off
- Rear dome light (w/o sun roof)
- Red
- Right front door switch (at right front door)
- Right rear door switch (at right rear door)
- Room
Instrument Illumination Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Illumination Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (5 bulbs)
- A/c ecu
- A10x
- A11x
- Acd mode changeover switch
- Ashtray illumination light
- C02
- C210
- C214
- Cigarette lighter illumination light
- Clock
- Column ecu
- Column switch
- Combination meter
- Engine compartment relay box (on left side of engine compartment)
- Fog light switch
- Front ecu
- Fuse 20 7.5a
- Fuse 21 7.5a
- G3 (at right side of front deck cross member)
- G7 (at top left side of dash)
- Hazard warning light switch
- Head
- Headlight leveling switch
- Hot at all times
- Illumination
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Lighting switch
- Off
- Radio & cd player
- Rheostat
- Tail
- Taillight relay
Instrument Illumination Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Instrument Illumination Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (5 bulbs)
- A/c ecu (behind center of dash, below radio)
- A/t selector lever position illumination light
- A10x
- A11x
- Ashtray illumination light
- C02
- Cigarette lighter illumination light
- Clock
- Column ecu
- Column switch
- Combination meter
- Engine compartment relay box (on left side of engine compartment)
- Fog light switch
- Front ecu
- Fuse 20 7.5a
- G3 (under right front kick panel)
- G7 (at top left side of dash)
- Hazard warning switch
- Head
- Hot at all times
- Illumination
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Lighting switch
- Nca
- Off
- Radio & cd player
- Rheostat
- Tail
- Taillight relay
POWER DISTRIBUTION
Power Distribution Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Power Distribution Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (connected to battery positive terminal)
- 20a
- Air conditioning & cooling fans systems
- Air conditioning system
- Air conditioning, sound, interior lights, defogger, instrument cluster, exterior lights & headlights systems
- Anti-lock brakes & exterior lights systems
- Anti-lock brakes system
- Battery
- Charging system
- Cooling fans, anti-theft & engine controls systems
- Door locks & exterior lights systems
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- Exterior lights & instrument cluster systems
- Front ecu
- Fuse 10 15a
- Fuse 11 30a
- Fuse 12 7.5a
- Fuse 13 10a
- Fuse 15 20a
- Fuse 16 10a
- Fuse 17 10a
- Fuse 18 10a
- Fuse 19 10a
- Fuse 20 7.5a
- Fuse 20a
- Fuse 21 7.5a
- Fuse 22 10a
- Fuse 25 30a
- Fuse 6 15a
- Fuse 7 10a
- Fuse 8 20a
- Fuse 9 10a
- Fusible link 1 60a
- Fusible link 2 50a
- Fusible link 26 100a
- Fusible link 27 60a
- Fusible link 3 60a
- Fusible link 4 40a
- Fusible link 5 30a
- G10 (at lower left rear of engine)
- G4 (left side of engine compt)
- Headlight relay high
- Headlight relay low
- Headlights system
- Horns & anti-theft systems
- Off
- Pnk
- Red
- Sound systems
- Sound, door locks, interior lights, instrument cluster, headlights, warning, power windows, wiper/washer, exterior lights & power tops systems
- Starting/
- Starting/ charging system
- Taillight relay
- To fuse 15 (diagram 2 of 2)
- To ignition switch (diagram 2 of 2)
- To junction block (diagram 2 of 2)
- W/ halogen headlamps
- W/ hid headlamps
Power Distribution Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Power Distribution Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- Acc
- Air conditioning system
- Air conditioning, wiper/washer, headlights & exterior lights, engine controls & anti-lock brakes systems
- Anti-lock brakes & power tops systems
- C211
- C212
- C214
- C225
- Cigarette lighter
- D23
- D24
- Defogger system
- Defogger system
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- From fusible link 1 (diagram 1 of 2)
- From fusible link 4 (diagram 1 of 2)
- From fusible link 5 (diagram 1 of 2)
- Fuse 1 10a
- Fuse 11 7.5a
- Fuse 12 7.5a
- Fuse 14 15a
- Fuse 15 15a
- Fuse 19 30a
- Fuse 2 7.5a
- Fuse 20 30a
- Fuse 21 20a
- Fuse 23 10a
- Fuse 3 7.5a
- Fuse 5 7.5a
- Fuse 7 20a
- Fuse 8 7.5a
- Fuse 9 15a
- G3 (at right side of front deck crossmember)
- Ignition switch
- Instrument cluster, interior lights & sound systems
- Junction block (behind left end of dash)
- Lock
- Mirrors system
- Power tops system
- Power windows system
- Red
- Start
- Starting/charging system
- Wiper/washer & interior lights systems
- Wiper/washer system
Power Distribution Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Power Distribution Wiring Diagram, Except Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (connected to battery positive terminal)
- Air conditioning & cooling fans systems
- Air conditioning system
- Air conditioning, sound, interior lights, defogger, transmissions, instrument cluster, exterior lights & head lights cruise control & systems
- Anti-lock brakes system
- Anti-lock brakes, cruise control, transmissions & exterior lights systems
- Battery
- Cruise control, engine controls & transmissions systems
- Door locks & exterior lights systems
- Engine compartment relay box (left side of engine compartment)
- Engine controls system
- Front ecu
- Fuse 10 15a
- Fuse 12 7.5a
- Fuse 13 10a
- Fuse 14 20a
- Fuse 15 15a
- Fuse 16 10a
- Fuse 17 10a
- Fuse 18 10a
- Fuse 19 10a
- Fuse 20 7.5a
- Fuse 21 7.5a
- Fuse 22 10a
- Fuse 24 20a
- Fuse 6 15a
- Fuse 7 10a
- Fuse 8 20a (2.4l)
- Fuse 9 10a
- Fusible link 1 60a
- Fusible link 2 50a
- Fusible link 26 120a
- Fusible link 3 60a
- Fusible link 4 40a
- Fusible link 5 30a
- G10 (at rear of cylinder head)
- G12 (at left front of engine compt, left of battery)
- Headlight relay high
- Headlight relay low
- Headlights system
- Horns & door locks systems
- Off
- Pnk
- Red
- Sound systems
- Sound, door locks, interior lights, instrument cluster, headlights, warning, power windows, power tops, wiper/washer & exterior lights systems
- Starting/ charging system
- Taillight relay
- To fuse 15 (diagram 2 of 2)
- To ignition switch (diagram 2 of 2)
- To junction block (diagram 2 of 2)
- Transmissions system
Power Distribution Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Power Distribution Wiring Diagram, Except Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (behind left end of dash) junction block
- 7.5a
- Acc
- Air conditioning system
- Air conditioning, wiper/washer, headlights & exterior lights systems
- Anti-lock brakes & power tops system
- C211
- C212
- C214
- C225
- Cigarette lighter
- Cruise control system
- D23
- D24
- Defogger system
- Engine compartment relay box (left side of engine compartment)
- Engine controls system
- From fusible link 1 (diagram 1 of 2)
- From fusible link 4 (diagram 1 of 2)
- From fusible link 5 (diagram 1 of 2)
- Fuse 1 10a
- Fuse 11 7.5a
- Fuse 12 7.5a
- Fuse 14 15a
- Fuse 15 15a
- Fuse 19 30a
- Fuse 2 7.5a
- Fuse 20 30a
- Fuse 21 20a
- Fuse 23 10a
- Fuse 3 7.5a
- Fuse 4 (2.0l)
- Fuse 5 7.5a
- Fuse 7 20a
- Fuse 8 7.5a
- Fuse 9 15a
- G3 (under right front kick panel)
- Ignition switch
- Instrument cluster, interior lights & sound systems
- Interior lights systems
- Junction block (behind left end of dash)
- Lock
- Mirrors system
- Power tops system
- Power windows system
- Red
- Start
- Starting/charging, engine controls, transmissions & cruise control systems
- Transmissions & engine controls systems
- Wiper/washer system
POWER DOOR LOCKS
Power Door Locks Wiring Diagram, Evolution with Keyless Entry for Mitsubishi Lancer Ralliart 2006
List of elements for Power Door Locks Wiring Diagram, Evolution with Keyless Entry for Mitsubishi Lancer Ralliart 2006:
- (at left front door) left front door switch
- (at right front door) right front door switch
- (at right front door) right rear door switch
- (under right front kick panel)
- C210
- C214
- C217
- C226
- C227
- C228
- Dedicated fuse 22 10a
- Door lock switch
- Engine compartment relay box (left side of engine compt)
- Etacs ecu
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in start or run
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Left door lock key cylinder switch (in left front door)
- Left front door lock actuator (in driver's door)
- Left rear door lock actuator (in left rear door)
- Left rear door switch (at left front door)
- Lock
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Power window main switch
- Power window sub switch
- Red
- Right front door lock actuator (in front passenger's door)
- Right front door lock switch
- Right rear door lock actuator (in right rear door)
- Unlock
Power Door Locks Wiring Diagram, Evolution without Keyless Entry for Mitsubishi Lancer Ralliart 2006
List of elements for Power Door Locks Wiring Diagram, Evolution without Keyless Entry for Mitsubishi Lancer Ralliart 2006:
- C210
- C214
- C217
- C226
- C227
- C228
- Dedicated fuse 22 10a
- Door lock switch
- Engine compartment relay box (on left side of engine compt)
- Etacs ecu
- G3 (at right side of front deck crossmember)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in start or run
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Left door lock key cylinder switch (in left front door)
- Left front door lock actuator (in driver's door)
- Left rear door lock actuator (in left rear door)
- Lock
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Power window main switch
- Power window sub switch
- Right front door lock actuator (in front passenger's door)
- Right front door lock switch
- Right rear door lock actuator (in right rear door)
- Unlock
Power Door Locks Wiring Diagram, Except Evolution with Keyless Entry for Mitsubishi Lancer Ralliart 2006
List of elements for Power Door Locks Wiring Diagram, Except Evolution with Keyless Entry for Mitsubishi Lancer Ralliart 2006:
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Dedicated fuse 22 10a
- Door lock switch
- Engine compartment relay box (left side of engine compt)
- Etacs ecu
- Exterior lights system
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- Horns system
- Hot at all times
- Hot in start or run
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Key reminder switch (in steering column)
- Left door lock key cylinder switch (in left front door)
- Left front door lock actuator (in driver's door)
- Left front door switch (at left front door)
- Left rear door lock actuator (in left rear door)
- Left rear door switch (at left rear door)
- Lock
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Power window main switch
- Power window sub switch
- Red
- Right front door lock actuator (in front passenger's door)
- Right front door lock switch
- Right front door switch (at right front door)
- Right rear door lock actuator (in right rear door)
- Right rear door switch (at right rear door)
- Unlock
Power Door Locks Wiring Diagram, Except Evolution without Keyless Entry for Mitsubishi Lancer Ralliart 2006
List of elements for Power Door Locks Wiring Diagram, Except Evolution without Keyless Entry for Mitsubishi Lancer Ralliart 2006:
- C210
- C214
- C217
- C218
- C226
- C227
- C228
- Dedicated fuse 22 10a
- Door lock switch
- Engine compartment relay box (on left side of engine compt)
- Etacs ecu
- G3 (at right side of front deck crossmember)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in start or run
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Left door lock key cylinder switch (in left front door)
- Left front door lock actuator (in driver's door)
- Left front door switch
- Left rear door lock actuator (in left rear door)
- Lock
- Multi- purpose fuse 15 15a
- Multi- purpose fuse 2 7.5a
- Nca
- Pnk
- Power window main switch
- Power window sub switch
- Red
- Right front door lock actuator (in front passenger's door)
- Right front door lock switch
- Right front door switch
- Right rear door lock actuator (in right rear door)
- Unlock
POWER MIRRORS
Power Mirrors Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Power Mirrors Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- C214
- Down
- G3 (at right side of front deck crossmember)
- Hot in acc or run
- Joint connector 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left
- Left remote controlled mirror
- Multi- purpose fuse 11 7.5a
- Nca
- Off
- Red
- Remote controlled mirror switch
- Right
- Right remote controlled mirror
Power Mirrors Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Power Mirrors Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (under right front kick panel)
- (under right front kick panel) g3
- C214
- Defogger system
- Down
- E03
- E10
- E19
- E20
- Hot in acc or on
- Htr
- Joint connector (behind right side of dash)
- Junction block (behind left end of dash)
- Left
- Left remote controlled mirror
- Multi- purpose fuse 11 7.5a
- Nca
- Off
- Red
- Remote controlled mirror switch
- Right
- Right remote controlled mirror
- W/ mirror heater
- W/o mirror heater
POWER TOP/SUNROOF
Power Top/Sunroof Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for Power Top/Sunroof Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- (behind instrument cluster) joint connector 2
- (evolution)
- (evolution: at right side of front deck crossmember)
- (lancer)
- C210
- C214
- C218
- C226
- C228
- Close/ down
- Control circuit
- Dedicated fuse 21 20a
- Engine compartment relay box (on left side of engine compartment)
- Etacs ecu
- Evolution
- G3 (lancer: under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- G8 g17 (evolution) (lancer) (at rear (at sunroof motor assembly)
- Headlights system
- Hot at all times
- Hot in on
- Hot in on or start
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (under left end of dash)
- Lancer
- Multi- purpose fuse 12 7.5a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 22 10a
- Off
- Open
- Red
- Shelf panel)
- Sun roof motor assembly (at rear of sun roof)
- Sun roof switch
- Wiper/washer, headlights & exterior lights systems
POWER WINDOWS
Power Windows Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Power Windows Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- Auto down
- C210
- C211
- C214
- C217
- C226
- C228
- Data link connector (below left side of dash)
- Door lock switch
- Door locks system
- Down
- Engine compartment relay box (on left side of engine compt)
- Etacs-ecu
- Fuse 22 10a
- Fusible link 5 30a
- G3 (at right side of front deck cross member)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in run or start
- Illum
- J/c 4
- Joint connector (behind right side of dash)
- Joint connector 1 (behind center of dash)
- Junction block (behind left end of dash)
- Left front door switch
- Left front power window regulator motor (in driver's side door)
- Left front power window switch
- Left rear power window switch
- Left rear power window regulator motor (in left rear door)
- Left rear power window sub switch
- Lock
- Lock switch
- Multi- purpose fuse 2 7.5a
- Nca
- Off
- Power window main switch
- Power window relay
- Red
- Right front door switch
- Right front power window switch
- Right front power window regulator motor (in right front door)
- Right front power window sub switch
- Right rear power window switch
- Right rear power window regulator motor (in right rear door)
- Right rear power window sub switch
- Unlock
Power Windows Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Power Windows Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- C210
- C211
- C214
- C217
- C226
- C228
- Data link connector (below left side of dash)
- Door lock switch
- Door locks system
- Down
- Engine compartment relay box (on left side of engine compt)
- Etacs-ecu
- Fuse 10a
- Fusible link 5 30a
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in run or start
- Illum
- Joint connector (behind right side of dash)
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Junction block (behind left end of dash)
- Left front door switch (at left front door)
- Left front power window switch
- Left front power window motor (in driver's side door)
- Left rear power window switch
- Left rear power window motor (in left rear door)
- Left rear power window sub switch
- Lock
- Lock switch
- Multi- purpose fuse 2 7.5a
- Nca
- Off
- Power window main switch
- Power window relay
- Red
- Right front door switch (at right front door)
- Right front power window switch
- Right front power window motor (in right front door)
- Right front power window sub switch
- Right rear power window switch
- Right rear power window motor (in right rear door)
- Right rear power window sub switch
- Unlock
RADIO
4-Speaker System Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for 4-Speaker System Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- (if equipped) pole antenna
- Antenna amplifier (if equipped)
- Antenna feeder
- Antenna feeder cable
- Cable nca
- Cd auto changer
- Dedicated fuse 20 7.5a
- Dedicated fuse 22 10a
- Dedicated fuse 23 10a
- Din cable
- Engine compartment relay box (on left side of engine compartment)
- Hot at all times
- Hot in on or acc
- Hot w/ taillight relay energized
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Left door speaker
- Left rear speaker
- Nca
- Radio & cd player
- Red
- Right door speaker
- Right rear speaker
- Roof antenna
6-Speaker System Wiring Diagram, Evolution without Amplifier for Mitsubishi Lancer Ralliart 2006
List of elements for 6-Speaker System Wiring Diagram, Evolution without Amplifier for Mitsubishi Lancer Ralliart 2006:
- Antenna amplifier
- Antenna feeder cable
- Cd auto changer
- Din cable
- Engine compartment relay box (on left side of engine compartment)
- Fuse 20 7.5a
- Fuse 22 10a
- Fuse 23 10a
- Hot at all times
- Hot in on or acc
- Hot w/ taillight relay energized
- Interior lights system
- Joint connector 1 (behind center of dash)
- Left front door speaker
- Left rear door speaker
- Left tweeter (w/ radio & cd player)
- Nca
- Pnk
- Radio & cd player
- Red
- Right front door speaker
- Right rear door speaker
- Right tweeter (w/ radio & cd player)
- Roof antenna
6-Speaker System Wiring Diagram, Except Evolution without Amplifier for Mitsubishi Lancer Ralliart 2006
List of elements for 6-Speaker System Wiring Diagram, Except Evolution without Amplifier for Mitsubishi Lancer Ralliart 2006:
- (behind instrument cluster) joint connector 5
- Antenna amplifier (if equipped)
- Antenna feeder cable
- Antenna feeder nca
- Cable
- Cd auto changer
- Dedicated fuse 20 7.5a
- Dedicated fuse 22 10a
- Dedicated fuse 23 10a
- Din cable
- Engine compartment relay box (on left side of engine compartment)
- Hot at all times
- Hot in on or acc
- Hot w/ taillight relay energized
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Left door speaker
- Left rear speaker
- Left tweeter
- Nca
- Pole antenna
- Radio & cd player
- Red
- Right door speaker
- Right rear speaker
- Right tweeter
- Roof antenna
7-Speaker System Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for 7-Speaker System Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- (evolution)
- (lancer)
- Antenna amplifier
- Antenna feeder cable
- Audio amplifier (under driver's seat)
- Cd auto changer
- Din cable
- Engine compartment relay box (on left side of engine compartment)
- Evolution
- Fuse 20 7.5a
- Fuse 22 10a
- Fuse 23 10a
- Fuse 24 20a
- G16 (evolution) (behind center of dash, on right dash support)
- G6 (lancer) (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in on or acc
- Hot w/ taillight relay energized
- Interior lights system
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Lancer
- Left door speaker
- Left rear speaker
- Left tweeter
- Nca
- Nca nca
- Pnk
- Radio & cd player
- Red
- Right door speaker
- Right rear speaker
- Right tweeter
- Roof antenna
- Woofer
STARTING/CHARGING
Charging Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Charging Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (connected to battery positive terminal)
- 40a
- 7.5a
- Acc
- Battery
- C01
- C119
- C121
- C211
- C214
- Combination meter
- Dedicated fuse 12
- Engine comp- artment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Fuse 2 7.5a
- Fusible link 26 100a
- Fusible link 4
- G10 (at lower left rear of engine)
- G4 (left side of engine compartment)
- Generator
- Generator malfunction light
- Ignition switch
- Joint connector 4
- Junction block (behind left end of dash)
- Lock
- Nca
- Red
- Run
- Start
- Starting circuit
Charging Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Charging Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (connected to battery positive terminal)
- 2.0l a/t
- 2.0l m/t
- 2.4l a/t
- 2.4l m/t
- 40a
- 7.5a
- Acc
- Battery
- C01
- C117
- C118
- C119
- C120
- C135
- C136
- C137
- C138
- C211
- C214
- Charge indicator
- Comb- ination meter
- Dedicated fuse 12
- Engine comp- artment relay box (left side of engine compt)
- Engine control module (m/t) (behind glove box)
- Fusible link 26 120a
- Fusible link 4
- G10 (at rear of cylinder head)
- G12 (at left front of engine compt, left of battery)
- Generator
- Ignition switch
- Joint connector 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Lock
- Multi- purpose fuse 2 7.5a
- Nca
- Powertrain control module (a/t) (behind glove box)
- Red
- Run
- Start
- Starting circuit
Starting Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006
List of elements for Starting Wiring Diagram, A/T for Mitsubishi Lancer Ralliart 2006:
- (connected to battery positive terminal)
- Acc
- Battery
- Charging circuit
- Engine compartment relay box (left side of engine compt)
- Engine controls system
- Fusible link 26 120a
- Fusible link 4 40a
- G10 (at rear of cylinder head)
- G12 (at left front of engine compt, left of battery)
- Ignition switch
- Joint connector 6 (behind lower center of dash)
- Lock
- Nca
- Run
- Start
- Starter
- Transmission range switch (left front of engine compt)
Starting Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006
List of elements for Starting Wiring Diagram, M/T for Mitsubishi Lancer Ralliart 2006:
- (at lower left rear of engine)
- (connected to battery positive terminal)
- Acc
- Battery
- Charging circuit
- Clutch interlock switch (lancer evolution) (left side of dash) interlock switch (lancer) (above clutch pedal, on bracket)
- Engine compartment relay box (on left side of engine compt)
- Engine controls system
- Fusible link 26 100a (lancer evolution) 120a (lancer)
- Fusible link 4 40a
- G10
- G10 (at rear of cylinder head)
- G12 (at left front of engine compt, left of battery)
- G15 (under left front kick panel)
- G4 (left side of engine compt)
- Ignition switch
- Lancer
- Lancer evolution
- Lock
- Nca
- Red
- Run
- Start
- Starter
- Starter relay (on engine compartment relay box)
SUPPLEMENTAL RESTRAINTS
Supplemental Restraints Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Supplemental Restraints Wiring Diagram, Evolution (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at left front of engine compartment) left front impact sensor
- (at right front of engine compartment) right front impact sensor
- (at top left side of dash) g7
- (behind center of dash, on right dash support) g16
- (partial) (below left side of
- Air bag drive circuit
- C-01
- C-02
- C-12
- C-214
- Clock spring
- Combination meter
- Connector lock switch (connector coupled: on) (connector uncoupled: off)
- Dash)
- Data
- Data link connector (dlc)
- Detection circuit
- Driver's side air bag module (squib) (in steering column)
- Fuse 7.5a
- Ground
- Hot in on or start
- Ignition
- J/c 2 (behind instrument cluster)
- J/c 4
- Junction block (behind left end of dash)
- Nca
- Off
- Srs ecu (behind lower center of dash)
- Srs indicator
- Warning light
Supplemental Restraints Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for Supplemental Restraints Wiring Diagram, Evolution (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (at base of right "b" pillar, behind trim) right seat belt pretensioner
- (at right side of dash) passenger's side air bag module squib
- (connector coupled: on) (connector uncoupled: off) connector lock switch
- Air bag drive circuit
- C-13
- Connector lock switch (connector coupled: on) (connector uncoupled: off)
- Left seat belt pretensioner (at base of left "b" pillar, behind trim)
- Nca
- Off
- Red
- Srs ecu (behind lower center of dash)
Supplemental Restraints Wiring Diagram, Except Evolution (1 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for Supplemental Restraints Wiring Diagram, Except Evolution (1 of 3) for Mitsubishi Lancer Ralliart 2006:
- (in dash
- 3c-21
- Air bag drive
- C-210
- C-214
- C-28
- Combination meter
- Connector lock switch (connector coupled: on) (connector uncoupled: off)
- Data
- Data link connector (dlc) (partial) (under left side of dash)
- Fuse 7.5a
- G16 (behind center of dash on right dash support)
- Grd
- Hot in on or start
- Hot with taillight relay energized
- Indicator drive ckt
- Interface
- J/c
- Junction block (left end of dash)
- Off
- Passenger's side air bag off indicator light
- Passenger's side seat belt warning light
- Pnk
- Power
- Red
- Relay box (left side of engine compt)
- S107 (in dash harn, behind lower center of dash)
- S108 (in instrument wiring harness behind right side of dash)
- Side impact
- Srs
- Srs ecu (behind lower center of dash)
- Warning light
- Wiring harness, behind center of dash) s106
Supplemental Restraints Wiring Diagram, Except Evolution (2 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for Supplemental Restraints Wiring Diagram, Except Evolution (2 of 3) for Mitsubishi Lancer Ralliart 2006:
- (connector coupled: on) (connector uncoupled: off) connector lock switch
- (connector coupled: on) connector uncoupled: off) connector lock switch
- Clock spring
- Driver's side air bag module squib
- G16 (behind center of dash, on right dash support)
- Left front impact sensor (at left front corner of engine compartment)
- Left occupant classification sensor (under left front seat)
- Nca
- Occupant classification ecu (under front of front passenger's seat)
- Off
- Passenger's side air bag module squib
- Pnk
- Right front impact sensor (at right front corner of engine compartment)
- Right occupant classification sensor (under right front seat)
- Twisted wires
Supplemental Restraints Wiring Diagram, Except Evolution (3 of 3) for Mitsubishi Lancer Ralliart 2006
List of elements for Supplemental Restraints Wiring Diagram, Except Evolution (3 of 3) for Mitsubishi Lancer Ralliart 2006:
- (connector coupled: on) (connector uncoupled: off) connector lock switch
- Air bag drive circuit
- Buckle sw
- C-27
- C-29
- Connector lock switch (connector coupled: on) (connector uncoupled: off)
- Driver's side seat belt buckle switch (in driver's seat belt buckle)
- Front impact sensor
- Left seat belt pretensioner (base of left "b" pillar)
- Left side air bag module squib (with side air bag)
- Left side impact sensor (with side air bag) (at base of left "b" pillar)
- Nca
- Occ sensor
- Off
- Passenger's side seat belt buckle switch (in passenger's seat belt buckle)
- Pnk
- Pretensioner drive circuit
- Red
- Right seat belt pretensioner (base of right "b" pillar)
- Right side air bag module squib (with side air bag)
- Right side impact sensor (with side air bag) (at base of right "b" pillar)
- Seat belt buckle switch
- Seat slide sensor (under driver's seat)
- Seat slide sensor detection
- Solid state
- Srs-ecu (behind lower center of dash)
- Twisted wires
TRANSMISSION
4WD Wiring Diagram, Evolution with ABS (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 4WD Wiring Diagram, Evolution with ABS (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (on left front corner of engine compt) proportioning valve
- Acd mode changeover switch
- Anti-lock brakes system
- Awd-ecu (behind lower right side of dash)
- C138
- C139
- C210
- C214
- Combination meter
- Computer data lines system
- Drive circuit
- Fuse 7.5a
- G3 (at right side of front deck crossmember)
- G4 (left side of engine compt)
- Gravel ind
- Hot in on
- Hot in on or start
- Ill
- Interior lights system
- J/c 2 (behind instrument cluster)
- J/c 3 (behind right side of dash)
- J/c 4
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Nca
- Parking brake switch (at base of parking brake lever)
- Pnk
- Red
- Snow ind
- Steering angular velocity sensor (at top of steering column)
- Tarmac ind
4WD Wiring Diagram, Evolution with ABS (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 4WD Wiring Diagram, Evolution with ABS (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (left side of engine compt)
- (on front wheel hub assembly)
- (under center console, left of parking brake lever assembly) (lateral) g-sensor
- Abs-ecu (on right rear of engine compt)
- C-214
- C117
- C119
- Electric pump (at left front corner of engine compt)
- Electric pump relay (at right side of firewall)
- Engine compartment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Engine controls system
- Exterior lights system
- Fuse 10a
- Fuse 15a
- Fuse 60a
- Fuse 7.5a
- Fusible link
- G-sensor (longitudinal) (under center console, left of parking brake lever assembly)
- Hot at all times
- Hot in on
- J/c 1 (behind center of dash)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Left front abs sensor
- Left rear abs sensor (on left rear hub assembly)
- Nca
- Pnk
- Pressure sensor (on left front corner of engine compt)
- Red
- Right front abs sensor
- Right rear abs sensor (on right rear hub assembly)
- Stoplight switch (above brake pedal, on bracket)
- Throttle position sensor (on throttle body)
4WD Wiring Diagram, Evolution without ABS (1 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 4WD Wiring Diagram, Evolution without ABS (1 of 2) for Mitsubishi Lancer Ralliart 2006:
- (on left front corner of engine compt) proportioning valve
- (under center console, left of parking brake lever assembly) (lateral) g-sensor
- Acd mode changeover switch
- Awd-ecu (behind lower right side of dash)
- C138
- C139
- C210
- C214
- Combination meter
- Computer data lines system
- Drive circuit
- Fuse 7.5a
- G-sensor (longitudinal) (under center console, left of parking brake lever assembly)
- G3 (at right side of front deck crossmember)
- G4 (left side of engine compt)
- Gravel ind
- Hot in on
- Hot in on or start
- Ill
- Interior lights system
- J/c 2 (behind instrument cluster)
- J/c 3 (behind right side of dash)
- J/c 4
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Nca
- Parking brake switch (at base of parking brake lever)
- Pnk
- Red
- Snow ind
- Steering angular velocity sensor (at top of steering column)
- Tarmac ind
4WD Wiring Diagram, Evolution without ABS (2 of 2) for Mitsubishi Lancer Ralliart 2006
List of elements for 4WD Wiring Diagram, Evolution without ABS (2 of 2) for Mitsubishi Lancer Ralliart 2006:
- (on front wheel hub assembly) right front abs sensor
- C117
- C119
- Electric pump (at left front corner of engine compt)
- Electric pump relay (at right side of firewall)
- Engine compartment relay box (on left side of engine compt)
- Engine control module (behind glove box)
- Engine controls system
- Exterior lights system
- Fuse 10a
- Fuse 15a
- Fuse 60a
- Fusible link
- G4 (left side of engine compt)
- Hot at all times
- Interior lights system
- J/c 1 (behind center of dash)
- J/c 6 (behind lower center of dash)
- Left front abs sensor (on front wheel hub assembly)
- Left rear abs sensor (on left rear hub assembly)
- Nca
- Pnk
- Pressure sensor (on left front corner of engine compt)
- Red
- Right rear abs sensor (on right rear hub assembly)
- Stoplight switch (above brake pedal, on bracket)
- Throttle position sensor (on throttle body)
2.0L
2.0L, A/T Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for 2.0L, A/T Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- (under front of center console) g14
- A/t control relay (on engine compt relay box)
- A/t control solenoid valve assembly (on rear of transaxle)
- A/t oil temp
- C-114
- C-116
- C-118
- C-120
- C210
- Crankshaft position sensor (on lower front of engine)
- Data link connector (below left side of dash)
- Engine compartment relay box (on left side of engine compt)
- Engine control system
- Engine controls system
- Engine coolant temperature sensor (on rear of cylinder head)
- Exterior lights system
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G14 (under front of center console)
- Hot at all times
- Hot in run or start
- Input shaft speed sensor (on top center of transaxle)
- J/c 2 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Low/ reverse
- Mfi relay (on engine compartment relay box)
- Output shaft speed sensor (on top right of transaxle)
- Over drive
- Powertrain control module (behind glove box)
- Red
- Second
- Starting/ charging system
- Stop light switch (above brake pedal, on bracket)
- Throttle position sensor (on throttle body)
- Torque converter control
- Transmission range switch (left front of engine compt)
- Under drive
2.4L
2.4L, A/T Wiring Diagram for Mitsubishi Lancer Ralliart 2006
List of elements for 2.4L, A/T Wiring Diagram for Mitsubishi Lancer Ralliart 2006:
- (behind lower center of dash) j/c 6
- (on rear of junction block, behind left end of dash) etacs ecu
- (on top center of transaxle) input shaft speed sensor
- A/t control relay (on engine compartment relay box)
- A/t control solenoid valve assembly (on rear of transaxle)
- A/t oil temp
- C-134
- C-136
- C-138
- C-140
- C-142
- C210
- C228
- Combination meter
- Data link connector (below left side of dash)
- Engine compartment relay box (on left side of engine compt)
- Engine controls system
- Exterior lights system
- Fuse 15a
- Fuse 20a
- Fuse 7.5a
- G14 (under front of center console)
- Hot at all times
- Hot in run or start
- J/c 2 (behind instrument cluster)
- J/c 5 (behind instrument cluster)
- J/c 6 (behind lower center of dash)
- Junction block (behind left end of dash)
- Low/ reverse
- Mfi relay (on engine compartment relay box)
- Output shaft speed sensor (on top right of transaxle)
- Over drive
- Powertrain control module (behind glove box)
- Red
- Second
- Starting/ charging system
- Stop light switch (above brake pedal,on bracket)
- Tac motor
- Throttle actuator control motor relay (on eng compt relay box)
- Throttle position sensor (on throttle body)
- Torque converter control
- Transmission range switch (left front of engine compt)
- Under drive
WARNING SYSTEMS
Warning Systems Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Warning Systems Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (at right side of front deck crossmember) g3
- (behind instrument cluster) joint connector 2
- (on top of steering column) column switch
- C01
- C02
- C210
- C214
- C217
- C226
- C227
- C228
- Column ecu
- Combination meter
- Computer data lines system
- Door ind
- Engine compartment relay box (on left side of engine compt)
- Etacs-ecu
- Fuse 10a
- G6 (behind center of dash, near left center reinforcement)
- Hot at all times
- Hot in run or start
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Junction block (behind left end of dash)
- Key reminder switch (in steering column)
- Left front door switch
- Multi- purpose fuse 2 7.5a
- Nca
- Red
- Seat belt ind
- Seat belt switch (inside driver's seat belt buckle)
Warning Systems Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Warning Systems Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (at left front door) left front door switch
- (behind instrument cluster) joint connector 5
- (under right front kick panel) g3
- C01
- C02
- C210
- C214
- C217
- C226
- C227
- C228
- Column ecu
- Column switch (on top of steering column)
- Combination meter
- Computer data lines system
- Door ind
- Engine compartment relay box (on left side of engine compt)
- Etacs-ecu
- Fuse 10a
- G6 (behind center of dash, near left center reinforcement)
- Headlights system
- Hot at all times
- Hot in run or start
- Joint connector 1 (behind center of dash)
- Joint connector 3 (behind right side of dash)
- Junction block (behind left end of dash)
- Key reminder switch (in steering column)
- Multi- purpose fuse 2 7.5a
- Nca
- Red
- Seat belt ind
- Seat belt switch (inside driver's seat belt buckle)
WIPER/WASHER
Front Wiper/Washer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Front Wiper/Washer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- A10x
- A11x
- Acc or on
- Air conditioning system
- C210
- C214
- C226
- C228
- Circuit breaker
- Column ecu
- Column switch
- Dedicated fuse 22 10a
- Engine compartment relay box (on left side of engine compartment)
- Engine controls system
- Etacs ecu
- Fast
- Front ecu (in engine compartment relay box)
- G13 (at left front corner of engine compartment)
- G14 (under front of center console)
- G3 (at right side of front deck crossmember)
- G6 (behind center of dash, near left center reinforcement)
- G8 (under rear seat back, at right upper corner of rear shelf panel)
- High
- Hot at all times
- Hot in
- Hot in on
- Hot in start
- Int
- Intermittent wiper interval adjusting knob
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 4
- Joint connector 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Low
- Mist
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Multi- purpose fuse 7 20a
- Or on
- Pnk
- Red
- Slow
- Vehicle speed sensor (on right side of transaxle)
- Wash
- Washer switch
- Windshield washer motor (at right rear of trunk, on washer fluid reservoir)
- Windshield wiper motor (on right rear of engine compt)
- Wiper switch
Front Wiper/Washer Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Front Wiper/Washer Wiring Diagram, Except Evolution for Mitsubishi Lancer Ralliart 2006:
- (at right rear of trunk, on washer fluid reservoir)
- 2.0l
- 2.4l
- A/t
- A10x
- A11x
- Acc or on
- C116
- C138
- C210
- C214
- C226
- C228
- Circuit breaker
- Column ecu
- Column switch
- Dedicated fuse 22 10a
- Engine compartment relay box (left side of engine compartment)
- Engine controls system
- Etacs ecu
- Fast
- Front-ecu (in engine compartment relay box)
- G1 (at right front corner of engine compartment)
- G13 (at left front corner of engine compt)
- G14 (under front of center console)
- G3 (under right front kick panel)
- G6 (behind center of dash, near left center reinforcement)
- High
- Hot at all times
- Hot in
- Hot in on
- Hot in start
- Int
- Intermittent wiper interval adjusting knob
- Joint connector 1 (behind center of dash)
- Joint connector 2 (behind instrument cluster)
- Joint connector 3 (behind right side of dash)
- Joint connector 5 (behind instrument cluster)
- Junction block (behind left end of dash)
- Low
- M/t
- Mist
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 5 7.5a
- Multi- purpose fuse 7 20a
- Off
- Or on
- Pnk
- Power tops system
- Powertrain control module (behind glove box)
- Slow
- Vehicle speed sensor (at left side of engine compartment)
- Wash
- Washer switch
- Windshield washer motor
- Windshield wiper motor (2.0l: on right rear of engine compt) (2.4l: at right rear of firewall)
- Wiper switch
Rear Wiper/Washer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006
List of elements for Rear Wiper/Washer Wiring Diagram, Evolution for Mitsubishi Lancer Ralliart 2006:
- (behind center of dash, near left center reinforcement) g6
- (behind instrument cluster) joint
- (under rear seat back, at left upper corner of rear shelf panel)
- Acc or on
- Back-up light switch (on transaxle)
- C210
- C214
- C217
- C226
- C227
- C228
- Column ecu
- Column switch
- Connector 2
- Connector 3 (behind right side of dash)
- Data link connector (below left side of dash)
- Dedicated fuse 22 10a
- Engine compartment relay box (on left side of engine compartment)
- Etacs ecu
- G3 (at right side of front deck crossmember)
- G8 (under rear seat back, at right upper corner of rear shelf panel)
- Hot at all times
- Hot in
- Joint
- Joint connector 1 (behind center of dash)
- Joint connector 4
- Junction block (behind left end of dash)
- Multi- purpose fuse 14 15a
- Multi- purpose fuse 2 7.5a
- Multi- purpose fuse 3 7.5a
- Nca
- Pnk
- Rear washer motor (at right rear of trunk, on washer fluid reservoir)
- Rear washer switch
- Rear wiper motor (below right side of rear speaker shelf)
- Rear wiper switch
- Red
- Start or on