Wiring Diagram VW GOL 2010 - Battery - starter - alternator - voltage regulator

A | Battery |
B | Starter |
C | Alternator |
C1 | Voltage regulator |
T1ag | Single pin connector, on starter |
T2bo | 2-pin connector, on alternator |
T2v | 2-pin connector, near battery |
T16c | 16-pin connector, yellow, next to relay plate |
1 | Earth strap, battery - body |
49 | Earth point, near battery |
D26 | Positive connection (B+), in alternator wiring harness |
P1 | Positive connection (30), in fuse holder on battery |
Wiring Diagram VW GOL 2010 - Ignition/starter switch - X-contact relief relay - terminal 30 wiring junction
D | Ignition/starter switch |
J59 | X-contact relief relay |
R | Radio |
SA15 | Fuse 15 on fuse holder A |
SA32 | Fuse 32 on fuse holder A |
T4b | 4-pin connector, on front interior light |
T6a | 6-pin connector, on X-contact relief relay |
T7c | 7-pin connector, on ignition/starter switch |
T8h | 8-pin connector, on radio |
T16b | 16-pin connector, red, next to relay plate |
T16c | 16-pin connector, yellow, next to relay plate |
TV2 | Terminal 30 wiring junction |
W1 | Front interior light |
A40 | Positive connection 1 (30), in dash panel wiring harness |
A49 | Connection 1, in dash panel wiring harness |
A99 | Connection 1 (87), in dash panel wiring harness |
Wiring Diagram VW GOL 2010 - Fuel pump relay
F4 | Reversing light switch |
J17 | Fuel pump relay |
J362 | Immobilizer control unit |
SA10 | Fuse 10 on fuse holder A |
SA11 | Fuse 11 on fuse holder A |
SA20 | Fuse 20 on fuse holder A |
SA21 | Fuse 21 on fuse holder A |
SA23 | Fuse 23 on fuse holder A |
SA24 | Fuse 24 on fuse holder A |
T2ax | 2-pin connector, on reversing light switch |
T8g | 8-pin connector, on immobilizer control unit |
T9b | 9-pin connector, on fuel pump relay |
T16f | 16-pin connector, black, behind the glove compartment |
T16g | 16-pin connector, red, behind the glove compartment |
A2 | Positive connection (15), in dash panel wiring harness |
A20 | Positive connection (15a), in dash panel wiring harness |
A32 | Positive connection (30), in dash panel wiring harness |
Wiring Diagram VW GOL 2010 - Hall sender - engine control unit - ignition transformer - ignition transformer output stage - ignition distributor - spark plug connector - spark plugs
G40 | Hall sender |
J623 | Engine control unit |
N152 | Ignition transformer |
N157 | Ignition transformer output stage |
O | Ignition distributor |
P | Spark plug connector |
Q | Spark plugs |
T2df | 2-pin connector, on ignition transformer output stage |
T3ag | 3-pin connector, on Hall sender |
T45a | 45-pin connector, on engine control unit |
343 | Earth connection (ignition coil), in injection system wiring harness |
Wiring Diagram VW GOL 2010 - Speedometer sender - engine control unit - active charcoal filter system solenoid valve 1 - push-in bridge
G22 | Speedometer sender |
J362 | Immobilizer control unit |
J365 | Air conditioning system switch-off relay |
J623 | Engine control unit |
N80 | Activated charcoal filter system solenoid valve 1 |
T2ar | 2-pin connector, on active charcoal filter system solenoid valve 1 |
T2dg | 2-pin connector, on push-in bridge |
T3ab | 3-pin connector, on speedometer sender |
T8g | 8-pin connector, on immobilizer control unit |
T9j | 9-pin connector, on air conditioning system switch-off relay |
T16f | 16-pin connector, black, behind the glove compartment |
T16g | 16-pin connector, red, behind the glove compartment |
T45a | 45-pin connector, on engine control unit |
TV23 | Push-in bridge |
43 | Earth point, lower part of right A-pillar |
491 | Earth connection 6, in injection system wiring harness |
E67 | Connection 1 (87a), in injection system wiring harness |
E95 | Connection 2 (vehicle speed sensor), in injection system wiring harness |
Wiring Diagram VW GOL 2010 - Engine control unit - injector - cylinder 1 - injector - cylinder 2 - injector - cylinder 3 - injector - cylinder 4 - throttle valve module
J623 | Engine control unit |
N30 | Injector, cylinder 1 |
N31 | Injector, cylinder 2 |
N32 | Injector, cylinder 3 |
N33 | Injector, cylinder 4 |
T2bd | 2-pin connector, on injector, cylinder 1 |
T2be | 2-pin connector, on injector, cylinder 2 |
T2bf | 2-pin connector, on injector, cylinder 3 |
T2bg | 2-pin connector, on injector, cylinder 4 |
T4n | 4-pin connector, on throttle valve positioner |
T5o | 5-pin connector, near cylinder head cover |
T45a | 45-pin connector, on engine control unit |
V60 | Throttle valve positioner |
G3 | Positive connection in wiring harness - injectors |
Wiring Diagram VW GOL 2010 - Intake air temperature sender - knock sensor 1 - coolant temperature sender - throttle valve potentiometer - intake manifold pressure sender
G42 | Intake air temperature sender |
G61 | Knock sensor 1 |
G62 | Coolant temperature sender |
G69 | Throttle valve potentiometer |
G71 | Intake manifold pressure sender |
J623 | Engine control unit |
T2as | 2-pin connector, on coolant temperature sender |
T2au | 2-pin connector, on knock sensor 1 |
T3f | 3-pin connector, on throttle valve potentiometer |
T4s | 4-pin connector, on intake air temperature sender |
T5n | 5-pin connector, near cylinder head cover |
T45a | 45-pin connector, on engine control unit |
492 | Earth connection 2 (sender earth), in injection system wiring harness |
Wiring Diagram VW GOL 2010 - Coolant temperature display sender - Lambda probe - engine control unit
F163 | Thermal switch for air conditioning system shut-off |
G2 | Coolant temperature sender |
G39 | Lambda probe |
J623 | Engine control unit |
T1af | Single pin connector, on thermal switch for air conditioning system shut-off |
T2j | 2-pin connector, on coolant temperature sender |
T4p | 4-pin connector, on Lambda probe |
T8b | 8-pin connector, behind centre dash panel |
T16b | 16-pin connector, red, next to relay plate |
T16f | 16-pin connector, black, behind the glove compartment |
T16g | 16-pin connector, red, behind the glove compartment |
T45a | 45-pin connector, on engine control unit |
335 | Earth connection 5, in dash panel wiring harness |
E66 | Connection 2 (30a), in injection system wiring harness |
Wiring Diagram VW GOL 2010 - Fuel gauge sender - fuel gauge - coolant temperature gauge - fuel system pressurisation pump
G | Fuel gauge sender |
G1 | Fuel gauge |
G3 | Coolant temperature gauge |
G6 | Fuel system pressurisation pump |
J285 | Control unit with display in dash panel insert |
K | Dash panel insert |
T4z | 4-pin connector, on fuel pump |
T16b | 16-pin connector, red, next to relay plate |
T16g | 16-pin connector, red, behind the glove compartment |
T32a | 32-pin connector, on dash panel insert |
21 | Earth point, near fuel pump |
44 | Earth point, lower part of left A-pillar |
86 | Earth connection 1, in rear wiring harness |
A193 | Positive connection (87a), in dash panel wiring harness |
* | only for Saveiro |
Wiring Diagram VW GOL 2010 - Oil pressure switch - control unit with display in dash panel insert - dash panel insert - alternator warning lamp - oil pressure warning lamp
F22 | Oil pressure switch |
G5 | Rev. counter |
J1 | Turn signal relay |
J285 | Control unit with display in dash panel insert |
K | Dash panel insert |
K2 | Alternator warning lamp |
K3 | Oil pressure warning lamp |
K101 | Speed warning lamp, yellow symbol |
K105 | Reserve fuel warning lamp |
T1c | Single pin connector, on oil pressure switch |
T9a | 9-pin connector, on turn signal relay |
T16a | 16-pin connector, behind driver storage compartment |
T16g | 16-pin connector, red, behind the glove compartment |
T32a | 32-pin connector, on dash panel insert |
44 | Earth point, lower part of left A-pillar |
81 | Earth connection 1, in dash panel wiring harness |
135 | Earth connection 2, in dash panel wiring harness |
VW GOL 2010 ABS control unit J104
ABS control unit -J104- |
|
Designation of connector: |
A - | ABS control unit -J104- |
B - | 31-pin connector, on ABS control unit -T31a- |
|
|
Designation of connector: |
A - | Airbag control unit -J234- |
B - | 75-pin connector, on ABS control unit -T75a- |
|
|
Designation of connector: |
A - | Control unit with display in dash panel insert -J285- |
B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
1 - | Vacant |
2 - | Engine control unit |
3 - | Terminal 15a |
4 - | Terminal R |
5 - | Fuel gauge sender |
6 - | Airbag control unit |
7 - | Terminal 31 |
8 - | Coolant temperature sender |
9 - | Terminal 31 |
10 - | Oil pressure switch |
11 - | Engine control unit |
12 - | Terminal 61 |
13 - | Engine control unit |
14 - | Terminal 75 |
15 - | Terminal 58 |
16 - | Terminal 58 |
17 - | Radio |
18 - | Radio |
19 - | ABS control unit |
20 - | Immobilizer control unit |
21 - | Radio |
22 - | Terminal L |
23 - | Terminal 30 |
24 - | Terminal 31 |
25 - | Terminal K |
26 - | Speedometer sender |
27 - | Engine control unit |
28 - | Speedometer sender |
29 - | Brake system monitoring |
30 - | Terminal 56a |
31 - | Terminal 58d |
32 - | Terminal 58d |
B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
Note
for models with 1.0 l Flex engine, 1.0 l and 1.4 l petrol engines only, from March 2008 |
1 - | Terminal 30 |
2 - | Terminal 31 |
3 - | Turn signal |
q | only for Gol Phoenix |
4 - | Terminal CAN-Bus high |
5 - | Terminal CAN-Bus low |
6 - | Vacant |
7 - | Radio |
8 - | Radio |
9 - | Radio |
10 - | Terminal 61 |
11 - | Terminal 56a |
12 - | ABS control unit |
13 - | Airbag control unit |
14 - | Brake system monitoring |
15 - | Immobilizer control unit |
16 - | Immobilizer control unit |
17 - | Terminal 15 |
18 - | Terminal 31 |
19 - | Vacant |
20 - | Terminal 31 |
21 - | CAN Shield |
22 - | Fuel gauge sender |
23 - | Oil pressure switch |
24 - | S-contact |
25 - | Speedometer sender |
26 - | Terminal K |
27 - | Terminal L |
28 - | Vacant |
29 - | Terminal 75 |
30 - | Terminal 58d |
31 - | Terminal 58d |
32 - | Terminal R |
Note
|
|
Designation of connector: |
A - | Control unit with display in dash panel insert -J285- |
B - | 32-pin connector, on control unit in dash panel insert -T32a- |
1 - | Speedometer sender |
2 - | Vacant |
3 - | Terminal 15 |
4 - | Terminal R |
5 - | Fuel gauge sender |
6 - | Airbag control unit |
7 - | Terminal 31 |
8 - | Coolant temperature sender |
9 - | Terminal 31 |
10 - | Oil pressure switch |
11 - | Engine control unit |
12 - | Terminal 61 |
13 - | Engine control unit |
14 - | Terminal 75 |
15 - | Oil pressure switch |
16 - | Immobilizer control unit |
17 - | Radio |
18 - | Radio |
19 - | ABS control unit |
20 - | Terminal 58d |
21 - | Radio |
22 - | Coolant shortage indicator sender |
23 - | Terminal 30 |
24 - | Terminal 31 |
25 - | Terminal K |
26 - | Terminal 58 |
27 - | Engine control unit |
28 - | Speedometer sender |
29 - | Brake system monitoring |
30 - | Terminal 56a |
31 - | Terminal L |
32 - | Terminal 56 |
|
|
Designation of connector: |
A - | Convenience system central control unit -J393- |
B - | 12-pin connector, on convenience system central control unit -T12c- |
C - | 23-pin connector, on convenience system central control unit -T23a- |
D - | 12-pin connector, on convenience system central control unit -T12b- |
|
|
Designation of connector: |
A - | Engine control unit -J623- |
B/C - | 80-pin connector, on engine control unit -T80a- |
|
|
Designation of connector: |
A - | Air conditioning system control unit -J301- |
B - | 5-pin connector, on air conditioning system control unit -T5d- |
C - | 7-pin connector, on heater control unit -T7d- |
|
|
Designation of connector: |
A - | Immobilizer control unit -J362- |
B - | 8-pin connector, on immobilizer control unit -T8g- |
C - | 2-pin connector, on immobilizer control unit -T2bp- |
|
|
Designation of connector: |
A - | Alarm system control unit -J85- |
B - | 22-pin connector, on alarm system control unit -T22a- |