Wiring Diagram VW SAVEIRO 2011 - Battery - starter - alternator - voltage regulator

A | Battery |
B | Starter |
C | Alternator |
C1 | Voltage regulator |
T2o | 2-pin connector, near battery |
T2p | 2-pin connector, on alternator |
1 | Earth strap, battery - body |
49 | Earth point, near battery |
500 | Screw connection 1 (30), on relay plate |
501 | Screw connection 2 (30), on relay plate |
D26 | Connection (B+), in alternator wiring harness |
P1 | Positive connection (30), in fuse holder on battery |
Wiring Diagram VW SAVEIRO 2011 - Ignition/starter switch - X-contact relief relay
D | Ignition/starter switch |
J59 | X-contact relief relay |
J362 | Immobilizer control unit |
R | Radio |
T6a | 6-pin connector, behind the right trim in front dash panel |
T7c | 7-pin connector, on ignition/starter switch |
T8a | 8-pin connector, on immobilizer control unit |
T8d | 8-pin connector, on radio |
A2 | Positive connection (15), in dash panel wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Lambda probe - engine control unit - throttle valve positioner
G39 | Lambda probe |
J301 | Air conditioning system control unit |
J362 | Immobilizer control unit |
J365 | Air conditioning system switch-off relay |
J623 | Engine control unit |
T4c | 4-pin connector, on Lambda probe |
T4w | 4-pin connector, on throttle valve positioner |
T6a | 6-pin connector, behind the right trim in front dash panel |
T6c | 6-pin connector, behind the right trim in front dash panel |
T7d | 7-pin connector, on air conditioning system control unit |
T8a | 8-pin connector, on immobilizer control unit |
T8b | 8-pin connector, behind dash panel |
T9a | 9-pin connector, on air conditioning system switch-off relay |
T80a | 80-pin connector, on engine control unit |
V60 | Throttle valve positioner |
E42 | Positive connection (30a), in injection system wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Speedometer sender - engine control unit - injector - cylinder 1 - injector - cylinder 2 - injector - cylinder 3 - injector - cylinder 4
G22 | Speedometer sender |
J623 | Engine control unit |
N30 | Injector, cylinder 1 |
N31 | Injector, cylinder 2 |
N32 | Injector, cylinder 3 |
N33 | Injector, cylinder 4 |
T2ca | 2-pin connector, on injector, cylinder 1 |
T2cb | 2-pin connector, on injector, cylinder 2 |
T2cc | 2-pin connector, on injector, cylinder 3 |
T2cd | 2-pin connector, on injector, cylinder 4 |
T3c | 3-pin connector, on speedometer sender |
T5p | 5-pin connector, near cylinder head cover |
T6a | 6-pin connector, behind the right trim in front dash panel |
T80a | 80-pin connector, on engine control unit |
331 | Earth connection, in injection system wiring harness |
E40 | Connection (speedometer sender), in injection system wiring harness |
G3 | Positive connection in wiring harness - injectors |
Wiring Diagram VW SAVEIRO 2011 - Engine control unit - cold start valve - active charcoal filter system solenoid valve 1 - ignition transformer - spark plug connector - spark plugs - fuel pump for cold start
J623 | Engine control unit |
N17 | Cold start valve |
N80 | Activated charcoal filter system solenoid valve 1 |
N152 | Ignition transformer |
P | Spark plug connector |
Q | Spark plugs |
T2b | 2-pin connector, on active charcoal filter system solenoid valve 1 |
T2bx | 2-pin connector, on cold start valve |
T2by | 2-pin connector, on fuel pump for cold start |
T3p | 3-pin connector, on ignition transformer |
T80a | 80-pin connector, on engine control unit |
V263 | Fuel pump for cold start |
E30 | Connection (87a), in engine wiring harness |
E45 | Connection (87), in injection system wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Fuel pump relay - cold start device relay - engine control unit
J17 | Fuel pump relay |
J41 | Cold start device relay |
J623 | Engine control unit |
T9b | 9-pin connector, on fuel pump relay |
T9k | 9-pin connector, on cold start device relay |
T80a | 80-pin connector, on engine control unit |
341 | Earth connection 2, in injection system wiring harness |
E41 | Positive connection (15), in injection system wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Engine speed sender - knock sensor 1 - coolant temperature sender - throttle valve potentiometer - engine control unit
G28 | Engine speed sender |
G61 | Knock sensor 1 |
G62 | Coolant temperature sender |
G69 | Throttle valve potentiometer |
J101 | Radiator fan 2nd speed relay |
J623 | Engine control unit |
T2d | 2-pin connector, on coolant temperature sender |
T2e | 2-pin connector, on knock sensor 1 |
T3a | 3-pin connector, on throttle valve potentiometer |
T3o | 3-pin connector, on engine speed sender |
T6k | 6-pin connector, behind the left trim in front dash panel |
T6n | 6-pin connector, behind the right trim in front dash panel |
T9c | 9-pin connector, on radiator fan 2nd speed relay |
T80a | 80-pin connector, on engine control unit |
339 | Earth connection (sender earth), in injection system wiring harness |
E47 | Positive connection 2 (5 Volt), in injection system wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Hall sender - intake air temperature sender - intake manifold pressure sender - engine control unit
F129 | Air conditioning system pressure switch |
G40 | Hall sender |
G42 | Intake air temperature sender |
G71 | Intake manifold pressure sender |
J209 | Fresh air blower and radiator fan relay |
J623 | Engine control unit |
T3b | 3-pin connector, on Hall sender |
T4e | 4-pin connector, on air conditioning system pressure switch |
T4x | 4-pin connector, on intake air temperature sender |
T5o | 5-pin connector, near cylinder head cover |
T6k | 6-pin connector, behind the left trim in front dash panel |
T6n | 6-pin connector, behind the right trim in front dash panel |
T9h | 9-pin connector, on fresh air blower and radiator fan relay |
T80a | 80-pin connector, on engine control unit |
342 | Earth connection 4, in injection system wiring harness |
E50 | Positive connection 3 (5 Volt), in injection system wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Fuel gauge sender - fuel system pressurisation pump
G | Fuel gauge sender |
G6 | Fuel system pressurisation pump |
S13 | Fuse in relay plate fuse holder |
S14 | Fuse in relay plate fuse holder |
T1a | Single pin connector, behind the right trim in front dash panel |
T4i | 4-pin connector, on fuel pump |
T6a | 6-pin connector, behind the right trim in front dash panel |
T6b | 6-pin connector, behind the right trim in front dash panel |
T6e | 6-pin connector, behind the dash panel near relay plate |
T6g | 6-pin connector, behind the dash panel near relay plate |
T16a | 16-pin connector, behind driver storage compartment |
51 | Earth point, in luggage compartment |
86 | Earth connection 1, in rear wiring harness |
335 | Earth connection 5, in dash panel wiring harness |
A164 | Positive connection 2 (30a), in dash panel wiring harness |
Wiring Diagram VW SAVEIRO 2011 - Oil pressure switch - coolant temperature sender - speedometer - control unit with display in dash panel insert - dash panel insert - alternator warning lamp
F22 | Oil pressure switch |
G1 | Fuel gauge |
G2 | Coolant temperature sender |
G3 | Coolant temperature gauge |
G5 | Rev. counter |
G21 | Speedometer |
J285 | Control unit with display in dash panel insert |
K | Dash panel insert |
K2 | Alternator warning lamp |
K3 | Oil pressure warning lamp |
K105 | Reserve fuel warning lamp |
K132 | Electric power control fault lamp |
T1p | Single pin connector, on oil pressure switch |
T2ag | 2-pin connector, on coolant temperature sender |
T6b | 6-pin connector, behind the right trim in front dash panel |
T6i | 6-pin connector, behind the left trim in front dash panel |
T16a | 16-pin connector, behind driver storage compartment |
T32a | 32-pin connector, on dash panel insert |
A76 | Connection (diagnosis wire K), in dash panel wiring harness |
A108 | Connection (speed signal), in dash panel wiring harness |
VW SAVEIRO 2011 ABS control unit J104
ABS control unit -J104- |
|
Designation of connector: |
A - | ABS control unit -J104- |
B - | 31-pin connector, on ABS control unit -T31a- |
|
|
Designation of connector: |
A - | Airbag control unit -J234- |
B - | 75-pin connector, on ABS control unit -T75a- |
|
|
Designation of connector: |
A - | Control unit with display in dash panel insert -J285- |
B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
1 - | Vacant |
2 - | Engine control unit |
3 - | Terminal 15a |
4 - | Terminal R |
5 - | Fuel gauge sender |
6 - | Airbag control unit |
7 - | Terminal 31 |
8 - | Coolant temperature sender |
9 - | Terminal 31 |
10 - | Oil pressure switch |
11 - | Engine control unit |
12 - | Terminal 61 |
13 - | Engine control unit |
14 - | Terminal 75 |
15 - | Terminal 58 |
16 - | Terminal 58 |
17 - | Radio |
18 - | Radio |
19 - | ABS control unit |
20 - | Immobilizer control unit |
21 - | Radio |
22 - | Terminal L |
23 - | Terminal 30 |
24 - | Terminal 31 |
25 - | Terminal K |
26 - | Speedometer sender |
27 - | Engine control unit |
28 - | Speedometer sender |
29 - | Brake system monitoring |
30 - | Terminal 56a |
31 - | Terminal 58d |
32 - | Terminal 58d |
B - | 32-pin connector, on control unit with display in dash panel insert -T32a- |
Note
for models with 1.0 l Flex engine, 1.0 l and 1.4 l petrol engines only, from March 2008 |
1 - | Terminal 30 |
2 - | Terminal 31 |
3 - | Turn signal |
q | only for Gol Phoenix |
4 - | Terminal CAN-Bus high |
5 - | Terminal CAN-Bus low |
6 - | Vacant |
7 - | Radio |
8 - | Radio |
9 - | Radio |
10 - | Terminal 61 |
11 - | Terminal 56a |
12 - | ABS control unit |
13 - | Airbag control unit |
14 - | Brake system monitoring |
15 - | Immobilizer control unit |
16 - | Immobilizer control unit |
17 - | Terminal 15 |
18 - | Terminal 31 |
19 - | Vacant |
20 - | Terminal 31 |
21 - | CAN Shield |
22 - | Fuel gauge sender |
23 - | Oil pressure switch |
24 - | S-contact |
25 - | Speedometer sender |
26 - | Terminal K |
27 - | Terminal L |
28 - | Vacant |
29 - | Terminal 75 |
30 - | Terminal 58d |
31 - | Terminal 58d |
32 - | Terminal R |
Note
|
|
Designation of connector: |
A - | Control unit with display in dash panel insert -J285- |
B - | 32-pin connector, on control unit in dash panel insert -T32a- |
1 - | Speedometer sender |
2 - | Vacant |
3 - | Terminal 15 |
4 - | Terminal R |
5 - | Fuel gauge sender |
6 - | Airbag control unit |
7 - | Terminal 31 |
8 - | Coolant temperature sender |
9 - | Terminal 31 |
10 - | Oil pressure switch |
11 - | Engine control unit |
12 - | Terminal 61 |
13 - | Engine control unit |
14 - | Terminal 75 |
15 - | Oil pressure switch |
16 - | Immobilizer control unit |
17 - | Radio |
18 - | Radio |
19 - | ABS control unit |
20 - | Terminal 58d |
21 - | Radio |
22 - | Coolant shortage indicator sender |
23 - | Terminal 30 |
24 - | Terminal 31 |
25 - | Terminal K |
26 - | Terminal 58 |
27 - | Engine control unit |
28 - | Speedometer sender |
29 - | Brake system monitoring |
30 - | Terminal 56a |
31 - | Terminal L |
32 - | Terminal 56 |
|
|
Designation of connector: |
A - | Convenience system central control unit -J393- |
B - | 12-pin connector, on convenience system central control unit -T12c- |
C - | 23-pin connector, on convenience system central control unit -T23a- |
D - | 12-pin connector, on convenience system central control unit -T12b- |
|
|
Designation of connector: |
A - | Engine control unit -J623- |
B/C - | 80-pin connector, on engine control unit -T80a- |
|
|
Designation of connector: |
A - | Air conditioning system control unit -J301- |
B - | 5-pin connector, on air conditioning system control unit -T5d- |
C - | 7-pin connector, on heater control unit -T7d- |
|
|
Designation of connector: |
A - | Immobilizer control unit -J362- |
B - | 8-pin connector, on immobilizer control unit -T8g- |
C - | 2-pin connector, on immobilizer control unit -T2bp- |
|
|
Designation of connector: |
A - | Alarm system control unit -J85- |
B - | 22-pin connector, on alarm system control unit -T22a- |