Wiring Diagram VW POLO 2013 - Battery - Starter - Alternator - Suppression filter - Airbag control unit - Battery isolation igniter - Fuse holder A - Fuse holder B - Fuse holder F
A | Battery |
B | Starter |
C | Alternator |
C1 | Voltage regulator |
C24 | Suppression filter |
J234 | Airbag control unit |
N253 | Battery isolation igniter |
SA | Fuse holder A |
SA1 | Fuse 1 in fuse holder A |
SB | Fuse holder B |
SB3 | Fuse 3 on fuse holder B |
SF | Fuse holder F |
SF3 | Fuse 3 in fuse holder F |
SA3 | Fuse 3 in fuse holder A |
SA6 | Fuse 6 in fuse holder A |
SB6 | Fuse 6 on fuse holder B |
T1m | Single connector |
T2gq | 2-pin connector |
T2gs | 2-pin connector |
T4 | 4-pin connector |
T50 | 50-pin connector |
A15 | Positive connection (15), in instrument wiring harness |
B170 | Positive connection 2 (30), in interior wiring harness |
K20 | Positive connection 1 (30), in radiator fan wiring harness |
Wiring Diagram VW POLO 2013 - Ignition/starter switch - Fuse holder B
D | Ignition/starter switch |
J59 | X-contact relief relay |
SB | Fuse holder B |
SB19 | Fuse 19 on fuse holder B |
SB20 | Fuse 20 on fuse holder B |
SB26 | Fuse 26 on fuse holder B |
SB28 | Fuse 28 on fuse holder B |
SB29 | Fuse 29 on fuse holder B |
SB30 | Fuse 30 on fuse holder B |
SB31 | Fuse 31 on fuse holder B |
SB32 | Fuse 32 on fuse holder B |
SB33 | Fuse 33 on fuse holder B |
SB35 | Fuse 35 on fuse holder B |
SB55 | Fuse 55 on fuse holder B |
SB58 | Fuse 58 on fuse holder B |
T6ba | 6-pin connector |
A32 | Positive connection (30), in dash panel wiring harness |
A33 | Connection (75), in dash panel wiring harness |
A40 | Positive connection 1 (30), in dash panel wiring harness |
A52 | Positive connection 2 (30), in dash panel wiring harness |
B170 | Positive connection 2 (30), in interior wiring harness |
B239 | Positive connection 1 (50), in interior wiring harness |
Wiring Diagram VW POLO 2013 - Starter inhibitor relay - Terminal 30 voltage supply relay - Additional coolant pump relay - Circulation pump
J207 | Starter inhibitor relay |
J317 | Terminal 30 voltage supply relay |
J496 | Additional coolant pump relay, on left in engine compartment |
J519 | Onboard supply control unit |
T2gk | 2-pin connector |
T5d | 5-pin connector |
T73a | 73-pin connector |
T73b | 73-pin connector |
V55 | Circulation pump |
135 | Earth connection 2, in dash panel wiring harness |
A132 | Connection (TCS/ESP), in dash panel wiring harness |
A151 | Connection 4 (87) in dash panel wiring harness |
B362 | Positive connection 13 (87a) in main wiring harness |
D76 | Connection (circulation pump), in engine compartment wiring harness |
* | Up to May 2011 |
*2 | From May 2011 |
*3 | From November 2012 |
Wiring Diagram VW POLO 2013 - Cruise control system switch - Radiator outlet coolant temperature sender - Engine control unit
E45 | Cruise control system switch |
G83 | Radiator outlet coolant temperature sender |
J623 | Engine control unit |
T2cw | 2-pin connector |
T41 | 41-pin connector |
T94 | 94-pin connector |
131 | Earth connection 2, in engine compartment wiring harness |
132 | Earth connection 3, in engine compartment wiring harness |
A130 | Connection (CCS), in dash panel wiring harness |
D182 | Connection 3 (87a) in engine compartment wiring harness |
* | From May 2013 |
Wiring Diagram VW POLO 2013 - Lambda probe - Lambda probe after catalytic converter - Engine control unit - Ignition coil 1 with output stage - Ignition coil 2 with output stage - Spark plug 1 - Spark plug 2
G39 | Lambda probe |
G130 | Lambda probe after catalytic converter |
J623 | Engine control unit |
N70 | Ignition coil 1 with output stage |
N127 | Ignition coil 2 with output stage |
Q23 | Spark plug 1 |
Q24 | Spark plug 2 |
T4a | 4-pin connector |
T4b | 4-pin connector |
T4h | 4-pin connector |
T6e | 6-pin connector |
T14 | 14-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
Z19 | Lambda probe heater |
Z29 | Lambda probe 1 heater after catalytic converter |
201 | Earth connection 5, in engine compartment wiring harness |
306 | Earth connection (ignition coils), in engine prewiring harness |
602 | Earth point, in front left footwell |
D110 | Connection 8 in engine compartment wiring harness |
E29 | Connection, in engine wiring harness |
Wiring Diagram VW POLO 2013 - Accelerator position sender 2 - Oil level and oil temperature sender - Brake servo pressure sensor - Engine control unit - Ignition coil 3 with output stage - Ignition coil 4 with output stage - Spark plug 3 - Spark plug 4
G185 | Accelerator position sender 2 |
G266 | Oil level and oil temperature sender |
G294 | Brake servo pressure sensor |
J623 | Engine control unit |
N291 | Ignition coil 3 with output stage |
N292 | Ignition coil 4 with output stage |
Q25 | Spark plug 3 |
Q26 | Spark plug 4 |
T3b | 3-pin connector |
T4as | 4-pin connector |
T4av | 4-pin connector |
T4c | 4-pin connector |
T6b | 6-pin connector |
T14 | 14-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
201 | Earth connection 5, in engine compartment wiring harness |
306 | Earth connection (ignition coils), in engine prewiring harness |
A139 | Connection 3 (15) in dash panel wiring harness |
D110 | Connection 8 in engine compartment wiring harness |
Wiring Diagram VW POLO 2013 - Brake light switch - Engine control unit - Injector - cylinder 1 - Injector - cylinder 2 - Injector - cylinder 3 - Injector - cylinder 4 - Vacuum pump for brakes
F | Brake light switch |
F47 | Brake pedal switch |
J104 | ABS control unit |
J623 | Engine control unit |
N30 | Injector, cylinder 1 |
N31 | Injector, cylinder 2 |
N32 | Injector, cylinder 3 |
N33 | Injector, cylinder 4 |
T2cl | 2-pin connector |
T2cm | 2-pin connector |
T2cn | 2-pin connector |
T2co | 2-pin connector |
T4e | 4-pin connector |
T6ar | 6-pin connector |
T38 | 38-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
V192 | Vacuum pump for brakes |
D73 | Positive connection (54), in engine compartment wiring harness |
Wiring Diagram VW POLO 2013 - Oil pressure switch - Fuel gauge sender - Knock sensor 1 - Fuel pump control unit - Engine control unit - Fuel pressure regulating valve
F1 | Oil pressure switch |
G | Fuel gauge sender |
G6 | Fuel system pressurisation pump |
G61 | Knock sensor 1 |
J538 | Fuel pump control unit |
J623 | Engine control unit |
N276 | Fuel pressure regulating valve |
T2cp | 2-pin connector |
T2g | 2-pin connector |
T5 | 5-pin connector |
T10w | 10-pin connector |
T14 | 14-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
81 | Earth connection 1, in dash panel wiring harness |
199 | Earth connection 3, in dash panel wiring harness |
Wiring Diagram VW POLO 2013 - Engine control unit - Control unit for structure-borne sound - Charge pressure control solenoid valve - Activated charcoal filter solenoid valve 1 - Camshaft control valve 1 - Turbocharger air recirculation valve - Magnetic clutch for supercharger - Actuator for structure-borne sound
J623 | Engine control unit |
J869 | Control unit for structure-borne sound |
N75 | Charge pressure control solenoid valve |
N80 | Activated charcoal filter solenoid valve 1 |
N205 | Camshaft control valve 1 |
N249 | Turbocharger air recirculation valve |
N421 | Magnetic clutch for supercharger |
R214 | Actuator for structure-borne sound |
T2cq | 2-pin connector |
T2gl | 2-pin connector |
T2gm | 2-pin connector |
T2gn | 2-pin connector |
T2go | 2-pin connector |
T2gp | 2-pin connector |
T12x | 12-pin connector |
T14 | 14-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
B279 | Positive connection 3 (15a) in main wiring harness |
D180 | Connection (87a), in engine compartment wiring harness |
* | Wiring colour depends on equipment |
Wiring Diagram VW POLO 2013 - Engine speed sender - Coolant temperature sender - Intake air temperature sender 2 - Radiator fan control unit - Engine control unit - 2-pin connector - Right radiator fan
G28 | Engine speed sender |
G31 | Charge pressure sender |
G62 | Coolant temperature sender |
G299 | Intake air temperature sender 2 |
J293 | Radiator fan control unit |
J623 | Engine control unit |
T2cr | 2-pin connector |
T2cz | 2-pin connector |
T3n | 3-pin connector |
T4ab | 4-pin connector |
T4au | 4-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
V7 | Radiator fan |
V35 | Right radiator fan |
D141 | Connection (5V) in engine prewiring harness |
Wiring Diagram VW POLO 2013 - High-pressure sender - Fuel pressure sender - Engine control unit - Air conditioner compressor regulating valve
G65 | High-pressure sender |
G247 | Fuel pressure sender |
J255 | Climatronic control unit |
J301 | Air conditioning system control unit |
J623 | Engine control unit |
N280 | Air conditioner compressor regulating valve |
SB25 | Fuse 25 on fuse holder B |
T2eo | 2-pin connector |
T3ag | 3-pin connector |
T3o | 3-pin connector |
T4 | 4-pin connector |
T60 | 60-pin connector |
82 | Earth connection 1, in front left wiring harness |
327 | Earth connection (sender earth), in engine compartment wiring harness |
A20 | Positive connection (15a), in dash panel wiring harness |
D174 | Connection 2 (5V) in engine prewiring harness |
* | According to equipment |
*2 | From May 2011 |
*3 | Up to May 2011 |
Wiring Diagram VW POLO 2013 - Hall sender - Intake air temperature sender - Intake air temperature sender 3 - Engine control unit
G40 | Hall sender |
G42 | Intake air temperature sender |
G71 | Intake manifold pressure sender |
G520 | Intake air temperature sender 3 |
G583 | Intake manifold pressure sender 3 |
J623 | Engine control unit |
T3c | 3-pin connector |
T4d | 4-pin connector |
T4n | 4-pin connector |
T60 | 60-pin connector |
Wiring Diagram VW POLO 2013 - Throttle valve module - Engine control unit - Regulating flap control unit
G186 | Throttle valve drive for electric throttle |
G187 | Throttle valve drive angle sender 1 for electric throttle |
G188 | Throttle valve drive angle sender 2 for electric throttle |
G584 | Regulating flap potentiometer |
J338 | Throttle valve module |
J623 | Engine control unit |
J808 | Regulating flap control unit |
T5a | 5-pin connector |
T6c | 6-pin connector |
T60 | 60-pin connector |
T94 | 94-pin connector |
V380 | Regulating flap position control motor |
B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
Wiring Diagram VW POLO 2013 - Coolant shortage indicator sender - Control unit in dash panel insert - Dash panel insert
G1 | Fuel gauge |
G32 | Coolant shortage indicator sender |
J285 | Control unit in dash panel insert |
K | Dash panel insert |
K2 | Alternator warning lamp |
K3 | Oil pressure warning lamp |
K43 | Coolant temperature warning lamp (too cold) |
K83 | Exhaust emissions warning lamp |
K105 | Reserve fuel warning lamp |
K149 | Engine electronics warning lamp |
T2cy | 2-pin connector |
T32 | 32-pin connector |
110 | Earth connection 2, in dash panel wiring harness |
269 | Earth connection (sender earth) 1, in dash panel wiring harness |
439 | Earth connection 3, in dash panel wiring harness |
B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
* | Up to November 2012 |
*2 | From November 2012 |
VW POLO 2013 Overview of control units
2 - | Actuator for structure-borne sound -R214- |
q | Fitting location |
3 - | ABS control unit -J104- |
q | Connector assignment |
4 - | Control unit for structure-borne sound -J869- |
q | Fitting location |
q | Connector assignment |
5 - | Airbag control unit -J234- |
q | Connector assignment |
6 - | Control unit with display for radio and navigation -J503- |
6 - | Air conditioning system control unit -J301- |
6 - | Climatronic control unit -J255- |
7 - | Multimedia system control unit -J650- |
7 - | Data bus diagnostic interface -J533- |
7 - | Headlight range control unit -J431- |
q | Fitting location |
q | Connector assignment |
9 - | Mobile telephone operating electronics control unit -J412- |
q | Connector assignment |
10 - | Sliding sunroof adjustment control unit -J245- |
11 - | Rear right door control unit -J389- |
q | Connector assignment |
12 - | Sliding sunroof adjustment control unit -J245- |
q | Fitting location from May 2010 |
13 - | Trailer detector control unit -J345- |
q | Connector assignment |
13 - | Parking aid control unit -J446- |
q | Connector assignment |
q | Fitting location |
15 - | Rear left door control unit -J388- |
q | Connector assignment |
16 - | Voltage stabiliser -J532- |
q | Fitting location |
q | Connector assignment |
17 - | Multifunction steering wheel control unit -J453- |
18 - | Heated front seats control unit -J774- |
q | Fitting location right-hand drive |
q | Connector assignment |
19 - | Driver door control unit -J386- |
q | Connector assignment |
20 - | Control unit in dash panel insert -J285- |
21 - | Onboard supply control unit -J519- |
q | Connector assignment |
22 - | Windscreen wiper motor -V- |
23 - | Engine control unit -J623- |
q | Connector assignment |
23 - | Power steering sensor -G250- |
24 - | Gas mode control unit -J659- |
q | Connector assignment up to November 2010 |
q | Connector assignment from November 2010 |
25 - | Power steering control unit -J500- |
26 - | Radiator fan control unit -J293- |
q | Fitting location from May 2011 |
q | Fitting location for models with two radiator fans |
q | Fitting location |
|
Connector assignment: |
A - | Control unit for structure-borne sound -J869- |
B - | 12-pin connector -T12x- |
|
Connector assignment: |
A - | ABS control unit -J104- |
B - | 38-pin connector -T38- |
Connector assignment: |
1 - | Airbag control unit -J234- |
2 - | 50-pin connector -T50- |
Control unit with display for radio and navigation -J503- |
Connector assignment: |
A - | Control unit with display for radio and navigation -J503- |
B - | Quadlock Connector |
q | 8-pin connector, black -T8k- |
q | 8-pin connector, brown -T8j- |
q | 12-pin connector, blue -T12f- |
C - | Radio -R- |
D - | Single connector for aerial |
E - | 26-pin connector -T26- |
F - | 2-pin connector for aerial |
G - | 12-pin connector, (connection for Japan) |
Air conditioning system control unit -J301- |
Connector assignment: |
A - | 5-pin connector -T5l- |
B - | 16-pin connector -T16h- |
C - | 18-pin connector -T18- |
D - | Air conditioning system control unit -J301- |
Climatronic control unit -J255- |
Connector assignment: |
A - | Climatronic control unit -J255- |
B - | 20-pin connector -T20- |
C - | 16-pin connector -T16i- |
Multimedia system control unit -J650- |
Fitting location: |
1 - | Multimedia system control unit -J650- |
2 - | 12-pin connector -T12e- |
|
Note:
|
Connector assignment. |
1 - | Front passenger door control unit -J387- |
2 - | 16-pin connector -T16l- |
|
Connector assignment: |
1 - | Mobile telephone operating electronics control unit -J412- |
2 - | 54-pin connector -T54- |
Sliding sunroof adjustment control unit -J245- |
Fitting location up to May 2010 |
1 - | Sliding sunroof adjustment control unit -J245- |
2 - | 16-pin connector -T16m- |
Note:
|
Connector assignment. |
1 - | Rear right door control unit -J389- |
2 - | 16-pin connector -T16k- |
Sliding sunroof adjustment control unit -J245- |
Fitting location from May 2010 |
1 - | Sliding sunroof adjustment control unit -J245- |
A - | 10-pin connector -T10x- |
|
Connector assignment: |
A - | 16-pin connector -T16f- |
B - | 12-pin connector -T12a- |
C - | Trailer detector control unit -J345- |
Parking aid control unit -J446- |
Connector assignment: |
A - | 16-pin connector -T16e- |
B - | Not assigned |
C - | 12-pin connector -T12- |
D - | Parking aid control unit -J446- |
|
|
Connector assignment. |
1 - | Rear left door control unit -J388- |
2 - | 16-pin connector -T16j- |
|
|
Multifunction steering wheel control unit -J453- |
Fitting location: |
A - | Multifunction steering wheel control unit -J453- |
B - | 5-pin connector -T5m- |
C - | 6-pin connector -Flachleiter- |
|
|
Connector assignment: |
1 - | Heated front seats control unit -J774- |
2 - | 16-pin connector -T16n- |
|
Connector assignment. |
1 - | Driver door control unit -J386- |
2 - | 16-pin connector -T16g- |
Control unit in dash panel insert -J285- |
1 - | Control unit in dash panel insert -J285- |
2 - | 32-pin connector -T32- |
Onboard supply control unit -J519- |
Fitting location: |
1 - | Onboard supply control unit -J519- |
Connector assignment: |
A - | 73-pin connector -T73a- |
B - | 73-pin connector -T73b- |
Description of signal for onboard supply control unit -J519- |
Connector | Pin | Terminal |
A | 1 | - |
A | 2 | Left dipped beam output signal 1) |
A | 3 | - |
A | 4 | Interior lighting out put signal, door contact switch |
A | 5 | - |
A | 6 | Rear fog light output signal 1) |
A | 7 | Fog light switch input signal |
A | 8 | - |
A | 9 | - |
A | 10 | Rear lid release motor output signal |
A | 11 | Central locking motor "lock" output signal for all doors |
A | 12 | Central locking motor output signal for driver's door |
A | 13 | Central locking motor "Safe" output signal for all doors |
A | 14 | Central locking earth input signal (31) |
A | 15 | Central locking motor output signal for front passenger door and rear doors |
A | 16 | Central locking supply input signal (30) |
A | 17 | Central locking lock unit input signal for rear left door |
A | 18 | Central locking lock unit input signal for rear right door |
A | 19 | Driver side door contact switch input signal |
A | 20 | Front passenger side door contact switch input signal |
A | 21 | Central locking lock unit input signal for front passenger door |
A | 22 | Central locking lock unit input signal for driver's door |
A | 23 | Rear lid handle release button input signal |
A | 24 | Central locking input signal, driver door |
A | 25 | Interior locking button input signal |
A | 26 | Door contact switch input signal for rear right door |
A | 27 | Bonnet contact switch input signal |
A | 28 | Hazard warning light button input signal |
A | 29 | Horn plate input signal |
A | 30 | Rear lid lock position 2 input signal |
A | 31 | Rear lid lock position 1 input signal |
A | 32 | Right turn signal switch input signal |
A | 33 | Left turn signal switch input signal |
A | 34 | Door contact switch input signal for rear left door |
A | 35 | - |
A | 36 | Switch-off signal for heated seat |
A | 37 | - |
A | 38 | Heated exterior mirror output signal |
A | 39 | Earth input signal (31) |
A | 40 | Rear right side light bulb output signal |
A | 41 | Rear left side light bulb output signal |
A | 42 | Supply input signal (86s) for ignition/starter switch |
A | 43 | Brake pedal position sender input signal |
A | 44 | Supply input signal (15) for ignition/starter switch |
A | 45 | Side light switch input signal |
A | 46 | - |
A | 47 | - |
A | 48 | - |
A | 49 | Headlight washer system relay output signal |
A | 50 | - |
A | 51 | - |
A | 52 | Fuel supply relay output signal |
A | 53 | - |
A | 54 | Supply input signal (75a) for ignition/starter switch 1) |
A | 55 | Starter inhibitor relay output signal (only models with automatic gearbox) |
A | 56 | Hazard warning light system warning lamp signal output |
A | 57 | Interior monitoring "off" warning lamp output signal |
A | 58 | Central locking SAFE function warning lamp output signal |
A | 59 | Interior locking warning lamp output signal |
A | 60 | Heated rear window warning lamp output signal |
A | 61 | - |
A | 62 | Main beam output signal 1) |
A | 63 | Supply input signal (30), left headlight 1) |
A | 64 | Supply input signal (30), heated exterior mirrors |
A | 65 | Supply (30G) output signal, interior light and luggage compartment light |
A | 66 | Supply input signal (30), interior lights |
A | 67 | - |
A | 68 | Supply input signal (30), window wiper |
A | 69 | Window wiper position 1 output signal |
A | 70 | Window wiper earth input signal |
A | 71 | Window wiper position 2 output signal |
A | 72 | Horn output signal |
A | 73 | Horn supply input signal (30) |
B | 1 | - |
B | 2 | Right dipped beam output signal 1) |
B | 3 | - |
B | 4 | - |
B | 5 | - |
B | 6 | - |
B | 7 | - |
B | 8 | - |
B | 9 | Left fog light bulb output signal |
B | 10 | Right fog light bulb output signal |
B | 11 | Fog light bulb supply input signal (30) |
B | 12 | Reversing light output signal (only models with automatic gearbox) |
B | 13 | Turn signal and brake light supply input signal (30) |
B | 14 | Left turn signal output signal |
B | 15 | Right turn signal output signal |
B | 16 | Brake lights output signal |
B | 17 | LIN bus, door control unit and switches in steering wheel |
B | 18 | Powertrain CAN, low |
B | 19 | Powertrain CAN, high |
B | 20 | Convenience CAN, high |
B | 21 | Convenience CAN, low |
B | 22 | Diagnosis CAN, low |
B | 23 | Diagnosis CAN, high |
B | 24 | LIN bus, sliding sunroof adjustment control unit, rain and light detector sensor, interior monitoring sensor |
B | 25 | - |
B | 26 | - |
B | 27 | Window wiper position 1 input signal |
B | 28 | Central locking input signal, front passenger door |
B | 29 | - |
B | 30 | Interior monitoring deactivation switch input signal |
B | 31 | Heated rear window button input signal |
B | 32 | Wiper limit switch input signal |
B | 33 | - |
B | 34 | Switch and instrument illumination (58d) input signal |
B | 35 | - |
B | 36 | LIN bus, alarm horn |
B | 37 | Signal (K), diagnosis |
B | 38 | Earth input signal (31) for electronics |
B | 39 | Supply input signal (30) for electronics |
B | 40 | - |
B | 41 | - |
B | 42 | Brake contact switch input signal |
B | 43 | - |
B | 44 | Cruise control system "Set" input signal |
B | 45 | Cruise control system "On/Off" input signal |
B | 46 | Cruise control system "Reset" input signal |
B | 47 | Cruise control system "Cancel" input signal |
B | 48 | Reversing light switch input signal |
B | 49 | Signal (L) alternator |
B | 50 | Starter relay input signal 1) |
B | 51 | Supply input signal (75a) for ignition/starter switch |
B | 52 | Window washer pump supply input signal |
B | 53 | Window wiper position 2 input signal |
B | 54 | - |
B | 55 | Starter inhibitor signal (only models with automatic gearbox) |
B | 56 | - |
B | 57 | - |
B | 58 | Heated exterior mirror switch input signal |
B | 59 | Input signal for reference voltage (30) |
B | 60 | Input signal for earth - reference voltage (31) |
B | 61 | Washer pump motor and rear window wiper motor output signal |
B | 62 | Windscreen wiper intermittent operation input signal |
B | 63 | Heated rear window output signal |
B | 64 | - |
B | 65 | - |
B | 66 | - |
B | 67 | Heated rear window supply input signal (30) |
B | 68 | Supply input signal (30), right headlight 1) |
B | 69 | - |
B | 70 | - |
B | 71 | - |
B | 72 | - |
B | 73 | - |
1) Only models with start/stop system |
Engine control unit -J623- |
Fitting location: |
1 - | Windscreen wiper motor -V- |
2 - | 14-pin connector -T14- |
3 - | Brake light switch -F- |
4 - | Brake fluid level warning contact -F34- |
5 - | Engine control unit -J623- |
Connector assignment: |
-T80- - | 80-pin connector |
Note:
t | The T80 connector is composed of a 52-pin connector and a 28-pin connector. |
t | According to equipment |
Connector assignment: |
A - | Engine control unit -J623- |
B - | 94-pin connector -T94- |
C - | 60-pin connector -T60- |
Note:
t | The connector is composed of a 94-pin connector and a 60-pin connector. |
t | According to equipment |
|
|
Connector assignment: (to November 2010) |
A - | Gas mode control unit -J659- |
B - | 56-pin connector -T56-, on wiring harness |
Connector assignment: (from November 2010) |
Note:
Warning, special pin on connector! |
A - | Gas mode control unit -J659- |
B - | 48-pin connector -T48b- |
C - | 32-pin connector -T32a- |
Power steering control unit -J500- |
Fitting location: |
1 - | 4-pin connector -T4z- |
2 - | 2-pin connector -T2di- |
3 - | 3-pin connector -T3s- |
4 - | Power steering control unit -J500- |
5 - | Steering hydraulics pump -V119- |
6 - | Bass horn -H7- , 2-pin connector -T2fd- |
7 - | Treble horn -H2- , 2-pin connector -T2fc- |
|
|
|
|
|