SEAT MII 2013 – 1.0l petrol engine, CHYB . Wiring diagrams, Pin Connector, Location

Wiring Diagram SEAT MII 2013 - Main relay - Onboard supply control unit - Engine control unit - Terminal 75 voltage supply relay 1 - Fuse holder C

J271	Main relay
J519	Onboard supply control unit
J623	Engine control unit
J680	Terminal 75 voltage supply relay 1
SC	Fuse holder C
SC1	Fuse 1 on fuse holder C
SC3	Fuse 3 on fuse holder C
SC5	Fuse 5 on fuse holder C
SC19	Fuse 19 on fuse holder C
SC26	Fuse 26 on fuse holder C
SC31	Fuse 31 on fuse holder C
SC40	Fuse 40 on fuse holder C
SC42	Fuse 42 on fuse holder C
T7a	7-pin connector
T9	9-pin connector
T56a	56-pin connector
A2	Positive connection (15), in dash panel wiring harness
B146	Positive connection 1 (87), in interior wiring harness
B315	Positive connection 1 (30a) in main wiring harness
B321	Positive connection 7 (30a) in main wiring harness
B325	Positive connection 11 (30a) in main wiring harness
*	Up to May 2013
*2	From November 2013
*3	Up to November 2012
*4	From November 2012
*5	From May 2013
*6	Up to November 2013

Wiring Diagram SEAT MII 2013 - Ignition/starter switch - Onboard supply control unit - Engine control unit

D	Ignition/starter switch
J519	Onboard supply control unit
J623	Engine control unit
SB6	Fuse 6 on fuse holder B
T6a	6-pin connector
T7	7-pin connector
T56a	56-pin connector
T73b	73-pin connector
A104	Positive connection 2 (15), in dash panel wiring harness
B279	Positive connection 3 (15a) in main wiring harness
B350	Positive connection 1 (87a) in main wiring harness
B660	Connection (diagnosis terminal 50), in main wiring harness
*	Up to November 2013
*2	From November 2013
*3	Up to November 2012
*4	Up to May 2013
*5	From November 2012
*6	Only models with manual gearbox

Wiring Diagram SEAT MII 2013 - Steering column combination switch - Onboard supply control unit - Engine control unit

E45	Cruise control system switch
E227	Cruise control system (CCS) SET button
E595	Steering column combination switch
J519	Onboard supply control unit
J623	Engine control unit
T16d	16-pin connector
T41	41-pin connector
T56a	56-pin connector
T73a	73-pin connector
T73b	73-pin connector
A130	Connection (CCS), in dash panel wiring harness
B280	Positive connection 4 (15a) in main wiring harness
*	Up to November 2013
*2	From November 2013
*3	Only models with cruise control system (CCS)

Wiring Diagram SEAT MII 2013 - Accelerator pedal module - Onboard supply control unit - Engine control unit

GX2	Accelerator pedal module
G79	Accelerator position sender
G185	Accelerator position sender 2
J519	Onboard supply control unit
J623	Engine control unit
T6f	6-pin connector
T6p	6-pin connector, on lower section of right A-pillar
T56a	56-pin connector
*	Only left-hand drive models
*2	Only right-hand drive models

Wiring Diagram SEAT MII 2013 - Onboard supply control unit - Engine control unit - Ignition coil 1 with output stage - Ignition coil 2 with output stage - Ignition coil 3 with output stage

J519	Onboard supply control unit
J623	Engine control unit
N70	Ignition coil 1 with output stage
N127	Ignition coil 2 with output stage
N291	Ignition coil 3 with output stage
Q23	Spark plug 1
Q24	Spark plug 2
Q25	Spark plug 3
T4k	4-pin connector
T4m	4-pin connector
T4n	4-pin connector
T14	14-pin connector
T56	56-pin connector
T56a	56-pin connector
18	Earth point, on cylinder block
85	Earth connection 1, in engine compartment wiring harness
306	Earth connection (ignition coils), in engine prewiring harness
394	Earth connection 29, in main wiring harness
395	Earth connection 30, in main wiring harness
671	Earth point 1, on front of left longitudinal member
D101	Connection 1 in engine compartment wiring harness

Wiring Diagram SEAT MII 2013 - Lambda probe - Lambda probe after catalytic converter - Throttle valve module - Onboard supply control unit - Engine control unit

G39	Lambda probe
G130	Lambda probe after catalytic converter
G186	Throttle valve drive for electric throttle
G187	Throttle valve drive angle sender 1 for electric throttle
G188	Throttle valve drive angle sender 2 for electric throttle
J338	Throttle valve module
J519	Onboard supply control unit
J623	Engine control unit
N80	Activated charcoal filter solenoid valve 1
T2ba	2-pin connector
T4h	4-pin connector
T4i	4-pin connector
T6h	6-pin connector
T14	14-pin connector
T56	56-pin connector
T56a	56-pin connector
Z19	Lambda probe heater
Z29	Lambda probe 1 heater after catalytic converter
E29	Connection, in engine wiring harness

Wiring Diagram SEAT MII 2013 - Hall sender - Intake air temperature sender - Coolant temperature sender - Intake manifold pressure sender - Onboard supply control unit - Engine control unit - Injector - cylinder 1 - Injector - cylinder 2 - Injector - cylinder 3

G40	Hall sender
G42	Intake air temperature sender
G62	Coolant temperature sender
G71	Intake manifold pressure sender
J519	Onboard supply control unit
J623	Engine control unit
N30	Injector, cylinder 1
N31	Injector, cylinder 2
N32	Injector, cylinder 3
T2bb	2-pin connector
T2bc	2-pin connector
T2bd	2-pin connector
T2be	2-pin connector
T3q	3-pin connector
T4o	4-pin connector
T14	14-pin connector
T56	56-pin connector
D95	Connection (injectors), in engine compartment wiring harness
D102	Connection 2 in engine compartment wiring harness
D103	Connection 3 in engine compartment wiring harness
E56	Connection 1, in injection system wiring harness
E57	Connection 2, in injection system wiring harness
E58	Connection 3, in injection system wiring harness

Wiring Diagram SEAT MII 2013 - Brake light switch - Clutch pedal switch - Engine speed sender - Knock sensor 1 - Onboard supply control unit - Engine control unit - Camshaft control valve 1

F	Brake light switch
F36	Clutch pedal switch
G28	Engine speed sender
G61	Knock sensor 1
J519	Onboard supply control unit
J623	Engine control unit
N205	Camshaft control valve 1
T2bf	2-pin connector
T2bg	2-pin connector
T3s	3-pin connector
T4q	4-pin connector
T4r	4-pin connector
T14	14-pin connector
T56	56-pin connector
T56a	56-pin connector
T73a	73-pin connector
387	Earth connection 22, in main wiring harness
389	Earth connection 24, in main wiring harness
B131	Connection (54), in interior wiring harness
B351	Positive connection 2 (87a) in main wiring harness

Wiring Diagram SEAT MII 2013 - Oil pressure switch - Fuel delivery unit - Fuel pump relay - Onboard supply control unit - Engine control unit - Dash panel insert

F1	Oil pressure switch
G	Fuel gauge sender
GX1	Fuel delivery unit
G6	Fuel system pressurisation pump
J17	Fuel pump relay
J285	Control unit in dash panel insert
J519	Onboard supply control unit
J623	Engine control unit
K	Dash panel insert
K3	Oil pressure warning lamp
K31	Cruise control system warning lamp
K43	Coolant temperature warning lamp (too cold)
K54	Battery charge condition warning lamp: red LED for less than 12 Volt
K149	Engine electronics warning lamp
SC44	Fuse 44 on fuse holder C
T1c	Single connector
T5a	5-pin connector
T10c	10-pin connector
T14	14-pin connector
T32	32-pin connector
T56	56-pin connector
T56a	56-pin connector
T73a	73-pin connector
43	Earth point, lower part of right A-pillar
382	Earth connection 17, in main wiring harness
410	Earth connection 1 (sender earth) in main wiring harness
B332	Positive connection 18 (30a) in main wiring harness
D106	Connection 4 in engine compartment wiring harness
*	Up to May 2013

Wiring Diagram SEAT MII 2013 - Starter - Alternator - Starter inhibitor relay - Onboard supply control unit - Data bus diagnostic interface - Engine control unit - Dash panel insert

A	Battery
B	Starter
C	Alternator
J119	Multifunction indicator
J207	Starter inhibitor relay
J519	Onboard supply control unit
J533	Data bus diagnostic interface
J623	Engine control unit
K	Dash panel insert
SA1	Fuse 1 in fuse holder A
T1a	Single connector
T2bf	2-pin connector
T4f	4-pin connector
T10b	10-pin connector
T32	32-pin connector
T56a	56-pin connector
T73a	73-pin connector
T73b	73-pin connector
44	Earth point, lower part of left A-pillar
379	Earth connection 14, in main wiring harness
384	Earth connection 19, in main wiring harness
B327	Positive connection 13 (30a) in main wiring harness
B383	Connection 1 (powertrain CAN bus, high), in main wiring harness
B390	Connection 1 (powertrain CAN bus, low), in main wiring harness
*	Only models with automated manual gearbox
*2	Up to May 2013
*3	From May 2013
*4	Only models with manual gearbox

SEAT MII 2013 Overview of relay carriers

Overview of relay carriers

Figure shows left-hand drive model

   

2 -	Relay​ and​ fuse​ holder​ 1 -SR1-

q	Location: and relay assignment from October 2011

q	Location and relay assignment for models with right-hand drive, from October 2011:

SEAT MII 2013 Relay assignment on relay and fuse carrier 1 -SR1- , from October 2011   Note Figure shows left-hand drive model

1 -	Terminal​ 75​ voltage​ supply​ relay​ 1 -J680-

2 -	Terminal 15 voltage supply relay -J329-

3 -	Starter relay 2 -J907-

q	Models with start/stop system only

4 -	Main relay -J271-

5 -

Vacant

6 -	Starter relay 1 -J906-

q	Models with start/stop system only

7 -	Fuel pump relay -J17-

q

Slot 7/A

q	Models with a petrol engine only

7 -	Main and dip beam relay -J33-

q

Slot 7/B

q	Models with no start/stop system only

7 -	Emergency braking function relay -J1020-

q

Slot 7/B

q	Models with start/stop system only

8 -

Vacant

9 -

Vacant

10 -	Air conditioning system relay -J32-

11 -	Starter inhibitor relay -J207-

q

Slot 11/A

11 -	Relay for gas shut-off valves -J908-

q

Slot 11/B

q	Only models with CNG engine

12 -

Vacant

Note Figure​ shows​ right-hand drive​ model

1 -	Terminal​ 75​ voltage​ supply​ relay​ 1 -J680-

2 -	Terminal 15 voltage supply relay -J329-

3 -	Starter relay 2 -J907-

q	Models with start/stop system only

4 -	Main relay -J271-

5 -

Vacant

6 -	Starter relay 1 -J906-

q	Models with start/stop system only

7 -	Fuel pump relay -J17-

q

Slot 7/A

q	Models with a petrol engine only

7 -	Main and dip beam relay -J33-

q

Slot 7/B

q	Models with no start/stop system only

7 -	Emergency braking function relay -J1020-

q

Slot 7/B

q	Models with start/stop system only

8 -

Vacant

9 -

Vacant

10 -	Air conditioning system relay -J32-

11 -	Starter inhibitor relay -J207-

q

Slot 11/A

11 -	Fuel pump relay -J17-

q

Slot 11/B

q	Only models with CNG engine

12 -

Vacant

SEAT MII 2013

SEAT MII 2013

Overview of control units in passemger compartment, for models with left-hand drive

Figure shows left-hand drive model

   

1 -	Airbag control unit -J234-

q	Fitting location

2 -	PID (portable navigation and infotainment system) -J982-

q	Fitting location

3 -	Emergency braking function sensor unit -J939-

q	Fitting location

4 -	Heater control unit -J162-

q	Fitting location

4 -	Air​ conditioning​ system​ control​ unit​ -J301-

q	Fitting location

5 -	Sliding sunroof control unit -J245-

q	Fitting location

6 -	Rear window wiper motor -V12-

q	Fitting location

7 -	Parking aid control unit -J446-

q	Fitting location

8 -	Heated front seats control unit -J774-

q	Fitting location

9 -	DC/DC voltage converter -A19-

q	Fitting location

11 -	Control unit in dash panel insert -J285-

q	Fitting location

12 -	Power steering control unit -J500-

q	Fitting location

13 -	Onboard supply control unit -J519-

q	Fitting location

SEAT MII 2013 Overview of control units in passenger compartment, for models with right-hand drive   Note Figure​ shows​ right-hand drive​ model

1 -	Onboard supply control unit -J519-

q	Fitting location

2 -	Power steering control unit -J500-

q	Fitting location

3 -	Control unit in dash panel insert -J285-

q	Fitting location

5 -	Emergency braking function sensor unit -J939-

q	Fitting location

6 -	Rear window wiper motor -V12-

q	Fitting location

7 -	Parking aid control unit -J446-

q	Fitting location

8 -	Sliding sunroof control unit -J245-

q	Fitting location

9 -	Heater control unit -J162-

q	Fitting location

9 -	Air​ conditioning​ system​ control​ unit​ -J301-

q	Fitting location

10 -	DC/DC voltage converter -A19-

q	Fitting location

11 -	PID (portable navigation and infotainment system) -J982-

q	Fitting location

12 -	Heated front seats control unit -J774-

q	Fitting location

13 -	Airbag control unit -J234-

q	Fitting location

Airbag control unit -J234- Fitting location of airbag control unit -J234-

1 -	Airbag control unit -J234-

q	-A- 50-pin connector, -T50-

Back to overview SEAT MII 2013 PID (portable navigation and infotainment system) -J982- PID (portable navigation and infotainment system) -J982- Fitting location portable navigation and infotainment system -J982-

1 -	PID (portable navigation and infotainment system) -J982-

q	-A- 16-pin connector -T16e-

Back to overview SEAT MII 2013 Emergency braking function sensor unit -J939- Emergency braking function sensor unit -J939- Fitting location emergency braking function sensor unit -J939-

1 -	Emergency braking function sensor unit -J939-

q	-A- 7-pin connector -T7c-

Connector assignment emergency braking function sensor unit -J939-

-T7c-	Designation
1	--
2	--
3	Powertrain CAN low
4	Powertrain CAN, high
5	Terminal 15
6	--
7	Terminal 31

Back to overview SEAT MII 2013 Heater control unit -J162- Heater control unit -J162- Fitting location heater control unit -J162-

1 -	Heater control unit -J162-

q	-A- 5-connector -T5b-

q	-B- 16-pin connector -T16g-

q	-C- 18-pin connector -T18-

Connector assignment of heater control unit -J162-

-T5b-	Designation		-T16g-	Designation		-T18-	Designation
1	4th blower speed		1	--		1	--
2	3rd blower speed		2	--		2	--
3	2nd blower speed		3	--		3	--
4	1st blower speed		4	--		4	--
5	Supply +12V		5	--		5	--
			6	--		6	--
			7	--		7	--
			8	--		8	--
			9	--		9	--
			10	Terminal 31		10	--
			11	--		11	--
			12	Terminal 58d		12	--
			13	--		13	--
			14	--		14	--
			15	--		15	--
			16	--		16	--
						17	--
						18	--

Back to overview SEAT MII 2013 Air conditioning system control unit -J301- Air conditioning system control unit -J301- Fitting location of air conditioning system control unit -J301-

1 -	Air conditioning system control unit -J301-

q	-A- 5-connector -T5b-

q	-B- 16-pin connector -T16g-

q	-C- 18-pin connector -T18-

Connector assignment of air conditioning system control unit -J301-

-T5b-	Designation		-T16g-	Designation		-T18-	Designation
1	4th blower speed		1	AC signal		1	--
2	3rd blower speed		2	Evaporator earth		2	--
3	2nd blower speed		3	Evaporator signal		3	Evaporator temperature sensor signal
4	1st blower speed		4	--		4	Evaporator temperature sensor earth
5	Supply +12V		5	--		5	--
			6	--		6	--
			7	--		7	--
			8	--		8	--
			9	--		9	--
			10	Terminal 31		10	--
			11	Terminal 15		11	--
			12	Terminal 58d		12	--
			13	--		13	--
			14	--		14	--
			15	--		15	--
			16	--		16	--
						17	--
						18	--

Back to overview SEAT MII 2013 Sliding sunroof control unit -J245- Sliding sunroof control unit -J245- Fitting location of sliding sunroof control unit -J245-

1 -	Sliding sunroof control unit -J245-

q	-A- 10-pin connector -T10a-

Connector assignment sliding sunroof control unit -J245-

-T10a-	Designation
1	LIN
2	Sliding sunroof adjustment regulator supply
3	Sliding sunroof adjustment regulator slider
4	Sliding sunroof adjustment regulator earth
5	--
6	--
7	Sunroof button, pull/push
8	--
9	Terminal 31
10	Terminal 30

Back to overview SEAT MII 2013 Rear window wiper motor -V12- Rear window wiper motor -V12- Fitting location of rear window wiper motor -V12-

1 -	Rear window wiper motor -V12-

q	-A- 4-pin connector -T4a-

Connector assignment of rear window wiper motor -V12-

-T4a-	Designation
1	Terminal 31
2	Steering column switch, intermittent
3	Steering column switch, rear wash
4	Terminal 75

Back to overview SEAT MII 2013 Parking aid control unit -J446- Parking aid control unit -J446- Fitting location of parking aid control unit -J446-

1 -	Parking aid control unit -J446-

q	A = 16-pin connector -T16-

q	B - 12-pin connector -T12c-

Connector assignment parking aid control unit -J446-

-T16-	Designation		-T12c-	Designation
1	Terminal 15		1	--
2	Rear sound sender signal		2	--
3	--		3	Rear, centre sensor signal
4	--		4	Rear, right sensor signal
5	--		5	Rear, left sensor signal
6	Powertrain CAN, high		6	--
7	--		7	--
8	Terminal 31		8	Rear sensor earth
9	--		9	--
10	Rear sound sender supply		10	--
11	--		11	Rear sensor current
12	--		12	--
13	--
14	--
15	Powertrain CAN low
16	--

Back to overview SEAT MII 2013 Heated front seats control unit -J774- Heated front seats control unit -J774- Fitting location of heated front seat control unit -J774- , only for models with left-hand drive   Note Figure shows left-hand drive model

1 -	Heated front seats control unit -J774-

q	-A- 16-pin connector -T16a-

Fitting location of heated front seat control unit -J774- , only for models with right-hand drive   Note Figure​ shows​ right-hand drive​ model

1 -	Heated front seats control unit -J774-

q	-A- 16-pin connector -T16a-

Connector assignment of heated front seats control unit -J774-

-T16a-	Designation			Designation
1	LED, stage 1, right		9	Terminal 31
2	LED, stage 2, left		10	--
3	LED, stage 2, right		11	--
4	LED, stage 1, left		12	Button for right seat heating
5	Seat heating authorisation, BCM		13	Terminal 75
6	Button for left seat heating		14	Terminal 75
7	--		15	Seat heater left
8	--		16	Seat heater right

Back to overview SEAT MII 2013 DC/DC voltage converter1 -A19- Fitting location of voltage converter -A19-

1 -	DC/DC voltage converter -A19-

q	-A- 12-pin connector -T12a-

1)  Only models with start/stop system Connector assignment voltage converter -A19 -

-T12a-	Designation
1	Terminal 30
2	Terminal 31
3	Terminal 15
4	Terminal 50
5	--
6	--
7	Terminal 30 stab
8	--
9	--
10	--
11	--
12	--

Back to overview SEAT MII 2013 Control unit in dash panel insert -J285- Control unit in dash panel insert -J285- Fitting location of control unit in dash panel insert -J285-

1 -	Control unit in dash panel insert -J285-

q	A- 32-pin connector -T32-

Connector assignment control unit in dash panel insert -J285-

-T32-	Designation			Designation
1	Tank sender 1 full		17	--
2	Tank sender 1 empty		18	Coolant low level
3	--		19	Ambient temperature
4	--		20	Terminal 31 sensor earth
5	--		21	MFI to
6	--		22	MFI from
7	Transponder 1		23	MFI OK/Reset
8	Transponder 2		24	Belt latch
9	Speedometer output		25	Parking brake/EPB
10	Speedometer input		26	Brakes, general
11	--		27	Oil pressure
12	--		28	Powertrain CAN, high
13	Rear fog light		29	Powertrain CAN low
14	Main beam		30	--
15	--		31	Terminal 15
16	Terminal 31		32	Terminal 30

Back to overview SEAT MII 2013 Power steering control unit -J500- Power steering control unit -J500- Fitting location of power steering control unit -J500- , only for models with right-hand drive   Note Figure shows left-hand drive model

1 -	Power steering control unit -J500-

q	-A- 2-pin connector -T2aq-

q	-B- 3-pin connector -T3p-

q	-C- 6-pin connector -T6i-

q	-D- 6-pin connector -T6j-

Fitting location of power steering control unit -J500- , only for models with right-hand drive   Note Figure​ shows​ right-hand drive​ model

1 -	Power steering control unit -J500-

q	-A- 2-pin connector -T2aq-

q	-B- 3-pin connector -T3p-

q	-C- 6-pin connector -T6i-

q	-D- 6-pin connector -T6j-

Connector assignment of power steering control unit -J500-

-T2aq-	Designation		-T3p-	Designation
1	Terminal 31		1	Powertrain CAN low
2	Terminal 30A		2	Powertrain CAN, high
			3	Terminal 15

Back to overview SEAT MII 2013 Onboard supply control unit -J519- Onboard supply control unit -J519- Fitting location of onboard supply control unit -J519- for models with left-hand drive   Note Figure shows left-hand drive model

1 -	Onboard supply control unit -J519-

q	-A- 73-pin connector -T73a-, black

q	-B- 73-pin connector -T73b-, white

Fitting location of onboard supply control unit -J519- for models with right-hand drive   Note Figure​ shows​ right-hand drive​ model

1 -	Onboard supply control unit -J519-

q	-A- 73-pin connector -T73a-, black

q	-B- 73-pin connector -T73b-, white

Connector assignment onboard supply control unit -J519-

-T73a-	Designation		-T73b-	Designation
1	--		1	--
2	Left dipped beam		2	Right dipped beam
3	--		3	Left daytime running lights
4	Interior light dimmer		4	58D supply
5	Right daytime running lights		5	--
6	Rear fog light		6	--
7	Fog light, lighting rotary switch		7	Licence plate light
8	--		8	--
9	Emergency braking function button		9	Left fog light with cornering light
10	Central locking authorisation motor, rear lid		10	Right fog light with cornering light
11	Central locking, lock motor, driver		11	Terminal 30 reversing lights, dipped beam
12	Central locking, common motor, driver		12	Reversing light
13	Central locking, safe, driver		13	Terminal 30 left turn signal/brake light
14	Terminal 31 central locking		14	Left turn signal
15	Central locking motor front passenger		15	Right turn signal
16	Terminal 30 central locking		16	Brake light
17	--		17	--
18	--		18	Powertrain CAN low
19	Driver door rotary latch		19	Powertrain CAN high
20	Passenger door rotary latch		20	Convenience CAN high
21	Central locking status lock, front passenger		21	Convenience CAN low
22	Central locking status lock, driver		22	CAN diagnosis low
23	Unlock rear lid		23	CAN diagnosis high
24	Central locking lock position, driver		24	LIN 2, roof
25	Central locking unlock button		25	--
26	--		26	--
27	Bonnet contact		27	Front wipers 1st stage, steering column lock switch
28	Hazard warning button		28	Central locking lock position, front passenger
29	Horn button		29	Rotary light switch - zero position
30	Rear lid main latch		30	--
31	Rear lid first latch		31	Heated rear window button
32	Right turn signal, steering column switch		32	Front wiper, end switch
33	Left turn signal, steering column switch		33	--
34	--		34	--
35	--		35	--
36	Seat heating authorisation		36	--
37	--		37	LIN, alternator
38	Heated exterior mirror		38	Terminal 31 electronics
39	Terminal 31 signal earth		39	Terminal 30 electronics
40	Right side light		40	Terminal 31 signal earth
41	Left side light		41	--
42	Terminal S ignition switch		42	--
43	Brake light sensor		43	Rear fog light, rotary light switch
44	Terminal 15 ignition switch		44	CCS set, steering column switch
45	Side light, rotary light switch		45	CCS E/A, steering column switch
46	--		46	CCS RES, steering column switch
47	--		47	CCS cancel, steering column switch
48	--		48	Reversing light switch
49	--		49	Terminal L
50	--		50	Terminal 50 ignition switch
51	--		51	Terminal X ignition switch
52	Fuel pump relay		52	Dip beam position, rotary light switch
53	--		53	Front wipers 2nd stage, steering column lock switch
54	Terminal X relay		54	--
55	Starter inhibitor relay		55	Starter inhibitor signal
56	Hazard warning light button LED		56	Central locking status lock, rear lid
57	--		57	--
58	LED Safe LED		58	Heated exterior mirror switch
59	LED lock/unlock button		59	Terminal 30, reference
60	Heated rear window LED		60	Terminal 31, reference
61	--		61	Steering column switch, washer pump
62	Main beam, steering column switch		62	Steering column switch, front wiper intermittent
63	Terminal 30, left main/dipped beam, daytime driving lights		63	Heated rear window
64	Terminal 30 heated exterior mirror		64	--
65	Terminal 30G		65	--
66	Terminal 30, interior light/30G		66	--
67	--		67	Terminal 30 heated rear window
68	Terminal 30 windscreen wiper		68	Terminal 30, right main/dipped beam, daytime driving lights
69	Front wipers 1st stage		69	--
70	Brake earth, front wiper		70	--
71	Front wipers 2nd stage		71	--
72	Horn		72	--
73	Terminal 30 horn		73	--

Back to overview

SEAT MII 2013 Overview of fuse holder

Overview of fuse holder    

q	Fuse assignment, from October 2011

q	Fuse assignment, from May 2013

q	Fitting location right-hand drive

q	Fuse assignment, from October 2011

q	Fuse assignment, from May 2013

q	Fuse assignment, from October 2011

q	Fuse assignment, from May 2013

q	Fuse assignment, from October 2011

q	Fuse assignment, from May 2013

SEAT MII 2013 Location fuse holder A SA Location fuse holder A -SA-

1 -	Fuse holder A (SA)

⇒ Electrical system, Repair Group 97, Removing and installing fuse holders

Multifuse strip fuse

The fuse strip (multifuse) must be replaced as a complete unit.

Back to overview

SEAT MII 2013

Fuse assignment, fuse holder A -SA- , from October 2011

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SA1	B1	Fuse 1 on fuse holder A -SA1-	150A 175A 2	Alternator -C-	30
SA2	C1
SA3	D1	Fuse 3 on fuse holder A -SA3-	110 A	Fuse holder C -SC-	30
				Main relay -J271-
				Terminal​ 75​ voltage​ supply​ relay​ 1 -J680-
SA4	E1	Fuse 4 on fuse holder A -SA4-	40 A	Power steering control unit -J500-	30
SA5	F1	Fuse 5 on fuse holder A -SA5-	40 A	ABS control unit -J104-	30
SA6	G1	Fuse 6 on fuse holder A -SA6-	40 A	Radiator fan control unit -J293-	30
SA7	H1	Fuse 7 on fuse holder A -SA7-	50A	Electronic manual gearbox control unit -J514-1	30

1 Depends on equipment

2 Models with start/stop system only

Back to overview

SEAT MII 2013

Fuse assignment fuse holder A -SA- , from May 2013

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SA1	B1	Fuse 1 on fuse holder A -SA1-	150A 175A 2	Alternator -C-	30
SA2	C1	Fuse 2 on fuse holder A -SA2-	30 A	Amplifier -R12-	30
SA3	D1	Fuse 3 on fuse holder A -SA3-	110 A	Fuse holder C -SC-	30
				Main relay -J271-
				Terminal​ 75​ voltage​ supply​ relay​ 1 -J680-
SA4	E1	Fuse 4 on fuse holder A -SA4-	50 A	Power steering control unit -J500-	30
SA5	F1	Fuse 5 on fuse holder A -SA5-	40 A	ABS control unit -J104-	30
SA6	G1	Fuse 6 on fuse holder A -SA6-	40 A	Radiator fan control unit -J293-	30
SA7	H1	Fuse 7 on fuse holder A -SA7-	50A	Electronic manual gearbox control unit -J514-1	30

1 Depends on equipment

2 Models with start/stop system only

Back to overview

SEAT MII 2013 Fittings location fuse holder B -SB-

2 -	Fuse holder B (SB)

-	Fuse colours

50A - red

40 A - orange

30 A - light-green

25 A - natural (white)

20 A - yellow

15 A - light blue

10A - red

7.5 A - brown

5A - light-brown

3 A - violet

Back to overview

SEAT MII 2013

Fuse assignment, fuse holder B -SB- , from October 2011

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SB1	J1	Fuse 1 on fuse holder B -SB1-	25 A	ABS control unit -J104-	30
SB2	J2	Fuse 2 on fuse holder B -SB2-	30 A	Radiator​ fan​ thermal​ switch -F18-	30
				Radiator fan control unit -J293-
SB3	J3	Fuse 3 on fuse holder B -SB3-	5A	Radiator fan control unit -J293-	30
				Terminal Signition switch -D-
SB4	J4	Fuse 4 on fuse holder B -SB4-	10 A	ABS control unit -J104-	30
SB5	J5	Fuse 5 on fuse holder B -SB5-	5 A	Onboard supply control unit -J519-	30
				t  Reference
SB6	J6	Fuse 6 on fuse holder B -SB6-	30 A	Fuse holder C -SC- Ignition/starter switch -D-	30

Back to overview

SEAT MII 2013

Fuse assignment fuse holder B -SB- , from May 2013

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SB1	J1	Fuse 1 on fuse holder B -SB1-	30 A	ABS control unit -J104-	30
SB2	J2	Fuse 2 on fuse holder B -SB2-	30 A	Radiator​ fan​ thermal​ switch -F18-	30
				Radiator fan control unit -J293-
SB3	J3	Fuse 3 on fuse holder B -SB3-	7.5 A	Radiator fan control unit -J293-	30
				Terminal Signition switch -D-
SB4	J4	Fuse 4 on fuse holder B -SB4-	10 A	ABS control unit -J104-	30
SB5	J5	Fuse 5 on fuse holder B -SB5-	5 A	Onboard supply control unit -J519-	30
				t  Reference
SB6	J6	Fuse 6 on fuse holder B -SB6-	30 A	Fuse holder C -SC- Ignition/starter switch -D-	30

Back to overview

SEAT MII 2013 Fuse holder C SC

Fuse holder C -SC-

Fittings location fuse holder C -SC- , LHD

1 -	Fuse holder C -SC-

-	Fuse colours

50A - red

40 A - orange

30 A - light-green

25 A - natural (white)

20 A - yellow

15 A - light blue

10A - red

7.5 A - brown

5A - light-brown

3 A - violet

Back to overview

Fitting location fuse holder C -SC- , RHD

-	Fuse holder C -SC-

-	Fuse colours

50A - red

40 A - orange

30 A - light-green

25 A - natural (white)

20 A - yellow

15 A - light blue

10A - red

7.5 A - brown

5A - light-brown

3 A - violet

Back to overview

Fuse assignment, fuse holder C -SC- , from October 2011

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
1	-	Fuse 1 on fuse holder C -SC1-	5A	Dash panel insert -K-	15
				Engine control unit -J623-
				Radiator fan control unit -J293-
2	-	Fuse 2 on fuse holder C -SC2-	15 A	Air conditioning system relay -J32-	15
				Air​ conditioning​ system​ control​ unit​ -J301-
				Diagnostic connection -U31-
				High-pressure sender -G65-
3	-	Fuse 3 on fuse holder C -SC3-	7.5A	Brake light switch -F-	87
				Clutch pedal switch -F36-
				Camshaft​ control​ valve​ 1 -N205-
4	-	Fuse 4 on fuse holder C -SC4-	7.5A	Onboard supply control unit -J519-	58
				t  Light switch -E1- dipped beam/daytime driving lights/main beam
5	-	Fuse 5 on fuse holder C -SC5-	5A	Onboard supply control unit -J519- t  Ignition/starter switch -D-	15
				Cruise control system switch -E45-
6	-	Fuse 6 on fuse holder C -SC6-	5A	Headlight range control regulator -E102-	15
				Left headlight range control motor -V48-
				Right headlight range control motor -V49-
				Mirror adjustment switch -E43-
7	-	Fuse 7 on fuse holder C -SC7-	10 A	Selector lever -E313-	30
8	-	Fuse 8 on fuse holder C -SC8-	7.5A	Electronic manual gearbox control unit -J514-	15
				Selector lever -E313-
9	-	Fuse 9 on fuse holder C -SC9-	7.5A	Airbag​ control​ unit​ -J234-	15
				Dash panel centre switch module 2 -EX35-
10	-	Fuse 10 on fuse holder C -SC10-	5A	Parking aid control unit -J446-	15
11	-	Fuse 11 on fuse holder C -SC11-	10 A	Right headlight dipped beam bulb -M31-	30
12	-	Fuse 12 on fuse holder C -SC12-	5A	Dash panel insert -K-	75
				Rear left fog light bulb -L46-
13	-	Fuse 13 on fuse holder C -SC13-	10 A	Left headlight dipped beam bulb -M29-	30
14	-	Fuse 14 on fuse holder C -SC14-	15 A	Rear window wiper motor -V12-	75
15	-	Fuse 15 on fuse holder C -SC15-	15 A	Light switch -E1-	30
16	-	Fuse 16 on fuse holder C -SC16-	5A	Terminal 15 voltage supply relay -J329-	15
				Power steering control unit -J500-
17	-	Fuse 17 on fuse holder C -SC17-	15 A	Washer​ pump​ switch​ (automatic​ wash/wipe​ and​ headlight​ washer​ system) -E44-	15
18	-	Fuse 18 on fuse holder C -SC18-	7.5A	Reversing light switch -F4-	15
19	-	Fuse 19 on fuse holder C -SC19-	15 A	Injector,​ cylinder​ 1 -N30-	87
				Injector,​ cylinder​ 2 -N31-
				Injector,​ cylinder​ 3 -N32-
20	-	Fuse 20 on fuse holder C -SC20-	5A	ABS control unit -J104-	15
				Emergency braking function sensor unit -J939-
				Steering angle sensor -G85-
21	-	Fuse 21 on fuse holder C -SC21-	5A	Right side light bulb -M3-	58
				Right tail light bulb -M2-
				Number plate light -X-
				Onboard supply control unit -J519-
				t  Light switch -E1- , side lights
22	-	Fuse 22 on fuse holder C -SC22-	10 A	Left daytime running light bulb -L174-	58
				Right daytime running light bulb -L175-
23	-	Fuse 23 on fuse holder C -SC23-	5A	Left side light bulb -M1-	58
				Left tail light bulb -M4-
24	-	Fuse 24 on fuse holder C -SC24-	15 A	Headlight flasher switch -E5-	30
25	-	Fuse 25 on fuse holder C -SC25-	10 A	Windscreen and rear window washer pump -V59-	30
26	-	Fuse 26 on fuse holder C -SC26-	5A	Main relay -J271-	30
				Dash panel insert -K-
				Steering angle sensor -G85-
27	-	Fuse 27 on fuse holder C -SC27-	7.5A	Onboard supply control unit -J519-	30
				t  Front interior light -W1- t  Front passenger reading light -W13- t  Driver reading lamp -W19-
28	-	Fuse 28 on fuse holder C -SC28-	5A	Diagnostic connection -U31-	30
29	-	Fuse 29 on fuse holder C -SC29-	7.5A	Onboard supply control unit -J519-	30
30	-	Fuse 30 on fuse holder C -SC30-	5A	Onboard supply control unit -J519-	30
				t  Heated exterior mirror on driver side -Z4- t  Heated exterior mirror on front passenger side -Z5-
31	-	Fuse 31 on fuse holder C -SC31-	10 A	Lambda probe -G39-	87
				Lambda probe after catalytic converter -G130-
				Activated charcoal filter system solenoid valve 1 -N80-
32	-	Fuse 32 on fuse holder C -SC32-	15 A	Onboard supply control unit -J519-	30
				t  Turn signal/brake light
33	-	Fuse 33 on fuse holder C -SC33-	10 A	Right headlight main beam bulb -M32-	56a
34	-	Fuse 34 on fuse holder C -SC34-	10 A	Left headlight main beam bulb -M30-	56a
				Dash panel insert -K-
35	-	Fuse 35 on fuse holder C -SC35-
36	-	Fuse 36 on fuse holder C -SC36-	15 A	Cigarette lighter -U1-	75
37	-	Fuse 37 on fuse holder C -SC37-	30 A	Air​ conditioning​ system​ control​ unit​ -J301-	75
				Heater control unit -J162-
38	-	Fuse 38 on fuse holder C -SC38-	15 A	Radio -R-	30
39	-	Fuse 39 on fuse holder C -SC39-	30 A	Sliding sunroof control unit -J245-	30
40	-	Fuse 40 on fuse holder C -SC40-	15 A	Engine control unit -J623-	87
41	-	Fuse 41 on fuse holder C -SC41-	25 A	Onboard supply control unit -J519-	30
				t  Central locking
42	-	Fuse 42 on fuse holder C -SC42-	25 A	Ignition coil 1 with output stage -N70-	87
				Ignition coil 2 with output stage -N127-
				Ignition coil 3 with output stage -N291-
43	-	Fuse 43 on fuse holder C -SC43-	20A	Heated front seats control unit -J774-	75
				Dash panel centre switch module -EX22-
				Dash panel centre switch module 2 -EX35-
44	-	Fuse 44 on fuse holder C -SC44-	15 A	Fuel pump relay -J17-	30
45	-	Fuse 45 on fuse holder C -SC45-	20A	Light switch -E1-	30
46	-	Fuse 46 on fuse holder C -SC46-	30 A	Onboard supply control unit -J519-	30
				t  Heated rear window -Z1-
47	-	Fuse 47 on fuse holder C -SC47-	25 A	Front right window regulator switch -E41-	15
48	-	Fuse 48 on fuse holder C -SC48-	20A	Onboard supply control unit -J519-	30
				t  Treble tone horn -H2- t  Bass tone horn -H7-
49	-	Fuse 49 on fuse holder C -SC49-	20A	Onboard supply control unit -J519-	30
				t  Wiper motor control unit -J400-
50	-	Fuse 50 on fuse holder C -SC50-	15 A	Left fog light bulb -L22-	75
				Right fog light bulb -L23-
51	-	Fuse 51 on fuse holder C -SC51-	25 A	Front left window regulator switch -E40-	30

Back to overview

Fuse assignment fuse holder C -SC- , from May 2013

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
1	-	Fuse 1 on fuse holder C -SC1-	7.5A	Dash panel insert -K-	15
				Engine control unit -J623-
				Radiator fan control unit -J293-
2	-	Fuse 2 on fuse holder C -SC2-	15 A	Air conditioning system relay -J32-	15
				Air​ conditioning​ system​ control​ unit​ -J301-
				Diagnostic connection -U31-
				High-pressure sender -G65-
3	-	Fuse 3 on fuse holder C -SC3-	7.5A	Brake light switch -F-	87
				Clutch pedal switch -F36-
				Camshaft​ control​ valve​ 1 -N205-
4	-	Fuse 4 on fuse holder C -SC4-	7.5A	Onboard supply control unit -J519-	58
				t  Light switch -E1- dipped beam/daytime driving lights/main beam
5	-	Fuse 5 on fuse holder C -SC5-	7.5A	Onboard supply control unit -J519- t  Ignition/starter switch -D-	15
				Cruise control system switch -E45-
6	-	Fuse 6 on fuse holder C -SC6-	7.5A	Headlight range control regulator -E102-	15
				Left headlight range control motor -V48-
				Right headlight range control motor -V49-
				Mirror adjustment switch -E43-
7	-	Fuse 7 on fuse holder C -SC7-	10 A	Selector lever -E313-	30
8	-	Fuse 8 on fuse holder C -SC8-	7.5A	Electronic manual gearbox control unit -J514-	15
				Selector lever -E313-
9	-	Fuse 9 on fuse holder C -SC9-	7.5A	Airbag​ control​ unit​ -J234-	15
				Dash panel centre switch module 2 -EX35-
10	-	Fuse 10 on fuse holder C -SC10-	7.5A	Parking aid control unit -J446-	15
11	-	Fuse 11 on fuse holder C -SC11-	10 A	Right headlight dipped beam bulb -M31-	56b
12	-	Fuse 12 on fuse holder C -SC12-	7.5A	Dash panel insert -K-	55a
				Control unit in dash panel insert -J285-
				Rear left fog light bulb -L46-
				Onboard supply control unit -J519-
13	-	Fuse 13 on fuse holder C -SC13-	10 A	Left headlight dipped beam bulb -M29-	30
14	-	Fuse 14 on fuse holder C -SC14-	15 A	Rear window wiper motor -V12-	75
15	-	Fuse 15 on fuse holder C -SC15-	15 A	Light switch -E1-	30
16	-	Fuse 16 on fuse holder C -SC16-	7.5A	Terminal 15 voltage supply relay -J329-	15
				Power steering control unit -J500-
17	-	Fuse 17 on fuse holder C -SC17-	15 A	Washer​ pump​ switch​ (automatic​ wash/wipe​ and​ headlight​ washer​ system) -E44-	15
18	-	Fuse 18 on fuse holder C -SC18-	7.5A	Reversing light switch -F4-	15
19	-	Fuse 19 on fuse holder C -SC19-	15 A	Injector,​ cylinder​ 1 -N30-	87
				Injector,​ cylinder​ 2 -N31-
				Injector,​ cylinder​ 3 -N32-
20	-	Fuse 20 on fuse holder C -SC20-	7.5A	ABS control unit -J104-	15
				Emergency braking function sensor unit -J939-
				Steering angle sensor -G85-
21	-	Fuse 21 on fuse holder C -SC21-	7.5A	Right side light bulb -M3-	58
				Right tail light bulb -M2-
				Number plate light -X-
				Onboard supply control unit -J519-
				t  Light switch -E1- , side lights
22	-	Fuse 22 on fuse holder C -SC22-	10 A	Left daytime running light bulb -L174-	58
				Right daytime running light bulb -L175-
23	-	Fuse 23 on fuse holder C -SC23-	7.5A	Left side light bulb -M1-	58
				Left tail light bulb -M4-
24	-	Fuse 24 on fuse holder C -SC24-	15 A	Headlight flasher switch -E5-	30
25	-	Fuse 25 on fuse holder C -SC25-	10 A	Windscreen and rear window washer pump -V59-	53
26	-	Fuse 26 on fuse holder C -SC26-	7.5A	Main relay -J271-	30
				Dash panel insert -K-
				Steering angle sensor -G85-
27	-	Fuse 27 on fuse holder C -SC27-	7.5A	Onboard supply control unit -J519-	30
				t  Front interior light -W1- t  Front passenger reading light -W13- t  Driver reading lamp -W19-
28	-	Fuse 28 on fuse holder C -SC28-	7.5A	Diagnostic connection -U31-	30
29	-	Fuse 29 on fuse holder C -SC29-	7.5A	Onboard supply control unit -J519-	30
30	-	Fuse 30 on fuse holder C -SC30-	7.5A	Onboard supply control unit -J519-	30
				t  Heated exterior mirror on driver side -Z4- t  Heated exterior mirror on front passenger side -Z5-
31	-	Fuse 31 on fuse holder C -SC31-	10 A	Lambda probe -G39-	87
				Lambda probe after catalytic converter -G130-
				Activated charcoal filter system solenoid valve 1 -N80-
32	-	Fuse 32 on fuse holder C -SC32-	15 A	Onboard supply control unit -J519-	30
				t  Turn signal/brake light
33	-	Fuse 33 on fuse holder C -SC33-	10 A	Right headlight main beam bulb -M32-	56a
34	-	Fuse 34 on fuse holder C -SC34-	10 A	Left headlight main beam bulb -M30-	56a
				Dash panel insert -K-
35	-	Fuse 35 on fuse holder C -SC35-
36	-	Fuse 36 on fuse holder C -SC36-	20A	Cigarette lighter -U1-	75
37	-	Fuse 37 on fuse holder C -SC37-	30 A	Air​ conditioning​ system​ control​ unit​ -J301-	75
				Heater control unit -J162-
38	-	Fuse 38 on fuse holder C -SC38-	15 A	Radio -R-	30
39	-	Fuse 39 on fuse holder C -SC39-	30 A	Sliding sunroof control unit -J245-	30
40	-	Fuse 40 on fuse holder C -SC40-	15 A	Engine control unit -J623-	87
41	-	Fuse 41 on fuse holder C -SC41-	25 A	Onboard supply control unit -J519-	30
				t  Central locking
42	-	Fuse 42 on fuse holder C -SC42-	25 A	Ignition coil 1 with output stage -N70-	87
				Ignition coil 2 with output stage -N127-
				Ignition coil 3 with output stage -N291-
43	-	Fuse 43 on fuse holder C -SC43-	20A	Heated front seats control unit -J774-	75
				Dash panel centre switch module -EX22-
				Dash panel centre switch module 2 -EX35-
44	-	Fuse 44 on fuse holder C -SC44-	15 A	Fuel pump relay -J17-	30
45	-	Fuse 45 on fuse holder C -SC45-	20A	Light switch -E1-	30
46	-	Fuse 46 on fuse holder C -SC46-	30 A	Onboard supply control unit -J519-	30
				t  Heated rear window -Z1-
47	-	Fuse 47 on fuse holder C -SC47-	30 A	Front right window regulator switch -E41-	15
48	-	Fuse 48 on fuse holder C -SC48-	20A	Onboard supply control unit -J519-	30
				t  Treble tone horn -H2- t  Bass tone horn -H7-
49	-	Fuse 49 on fuse holder C -SC49-	30 A	Onboard supply control unit -J519-	30
				t  Wiper motor control unit -J400-
50	-	Fuse 50 on fuse holder C -SC50-	15 A	Left fog light bulb -L22-	55a
				Right fog light bulb -L23-
			20A1	Onboard supply control unit -J519-1
51	-	Fuse 51 on fuse holder C -SC51-	30 A	Front left window regulator switch -E40-	30

1 Models with start/stop system only Back to overview

Fuse holder D -SD-

Fitting location fuse holder D -SD- , LHD

A -	Fuse holder D -SD-

q	Models with start/stop system only

-	Fuse colours

50A - red

40 A - orange

30 A - light-green

25 A - natural (white)

20 A - yellow

15 A - light blue

10A - red

7.5 A - brown

5A - light-brown

3 A - violet

Back to overview

Fuse assignment, fuse holder D -SD- , from October 2011

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SD1		Fuse 1 on fuse holder D -SD1-	5A	Emergency braking function sensor unit -J939-	30
SD2		Fuse 2 on fuse holder D -SD2-	5A	Dash panel insert -K-	30
SD3		Fuse 3 on fuse holder D -SD3-	10 A	Radio -R-	30
SD4		Fuse 4 on fuse holder D -SD4-	7.5 A	Voltage converter -A19- Starter relay 1 -J906- Starter relay 2 -J907-	15
SD5
SD6
SD7
SD8
SD9		Fuse 9 on fuse holder D -SD9-	15 A	Onboard supply control unit -J519- t  Right main beam/dipped beam/daytime driving lights	30
SD10		Fuse 10 on fuse holder D -SD10-	15 A	Onboard supply control unit -J519- t  Left main beam/dipped beam/daytime driving lights	30
SD11		Fuse 11 on fuse holder D -SD11-	30 A	Starter relay 1 -J906- Starter relay 2 -J907-	30
SD12		Fuse 12 on fuse holder D -SD12-	30 A	Voltage converter -A19-	30

Back to overview

Fuse assignment fuse holder D -SD- , from May 2013

No.		Current Flow Diagram designation	Nominal value	Function/component	Terminal
SD1		Fuse 1 on fuse holder D -SD1-	7.5A	Emergency braking function relay -J1020- Emergency braking function sensor unit -J939-	30
SD2		Fuse 2 on fuse holder D -SD2-	7.5A	Dash panel insert -K-	30
SD3		Fuse 3 on fuse holder D -SD3-	15 A	Radio -R-	30
SD4		Fuse 4 on fuse holder D -SD4-	7.5 A	Voltage converter -A19- Starter relay 1 -J906- Starter relay 2 -J907-	15
SD5
SD6
SD7
SD8
SD9		Fuse 9 on fuse holder D -SD9-	15 A	Onboard supply control unit -J519- t  Right main beam/dipped beam/daytime driving lights	30
SD10		Fuse 10 on fuse holder D -SD10-	15 A	Onboard supply control unit -J519- t  Left main beam/dipped beam/daytime driving lights	30
SD11		Fuse 11 on fuse holder D -SD11-	30 A	Starter relay 1 -J906- Starter relay 2 -J907-	30
SD12		Fuse 12 on fuse holder D -SD12-	30 A	Voltage converter -A19-	30

Back to overview